Modeling thermal analysis for predicting thermal hazards relevant to transportation safety and runaway reaction for 2,2′-azobis(isobutyronitrile)

The pure decomposition behavior of 2,2′-azobis (isobutyronitrile) (AIBN) and its physical phase transformation were examined and discussed. The thermal decomposition of this self-reactive azo compound was explored using differential scanning calorimetry (DSC) to elucidate the stages in the progress of this chemical reaction. DSC was used to predict the kinetic and process safety parameters, such as self-accelerating decomposition temperature (SADT), time to maximum reaction rate under adiabatic conditions (TMR_ad), and apparent activation energy (E_a), under isothermal and adiabatic conditions with thermal analysis models. Moreover, vent sizing package 2 (VSP2) was applied to examine the runaway reaction combined with simulation and experiments for thermal hazard assessment of AIBN. A thorough understanding of this reaction process can identify AIBN as a hazardous and vulnerable chemical during upset situations. The sublimation and melting of AIBN near its apparent onset decomposition temperature contributed to the initial steps of the reaction and explained the exothermic attributes of the peaks observed in the calorimetric investigation.     

Experimental hazardous risk investigation of energetic styphnic acid analytical reagent in calorimetric analysis

Analytical reagents identify and manage metal pollution, a major environmental issue. Regrettably, these compounds' safety concerns, especially when heated, have been neglected. This research examines the thermal hazard of the extremely reactive analytical reagent styphnic acid. Differential scanning calorimetry, thermogravimetric analysis, and accelerating rate calorimetry examined styphnic acid's thermodynamics. Thermogravimetric analysis showed weight loss reactions starting at 127 °C and peaking at 208 °C. Differential scanning calorimetry showed an endothermic peak at 176 °C. The accelerating rate calorimetry test showed that styphnic acid self-accelerates at 237 °C after 196.5 °C. Kissinger, Ozawa-Flynn-Wall, and Kissinger-Akahira-Sunose thermokinetic models calculated apparent activation energy from 131.677 to 155.718 kJ/mol. A nonlinear regression analysis showed that styphnic acid undergoes a two-step autocatalytic reaction during heat degradation. Thermal safety was assessed by measuring time to conversion limit, maximum rate, total energy release, self-accelerating decomposition temperature, and adiabatic temperature rise. Styphnic acid is less stable at higher temperatures and its thermal hazards depend on heating rate. The computed SADT was 109.04 °C, with alarm and control temperatures of 104.04 and 99.04 °C, respectively. The risk matrix analysis based on T_ad and TMR_ad suggests reducing thermal instability. This study on styphnic acid's thermal risks and safe storage and transit during analytical applications is beneficial.     

Effects of metal ions on thermal hazard of tert-butyl peroxy-3,5,5-trimethylhexanoate

As a commonly used initiator for polyethylene, tert-butyl peroxide 3,5,5-trimethylhexanoate (TBPTMH), with the molecular formula of C₁₃H₂₆O₃, is more likely to decompose and cause fires and explosions. Understanding the thermal risks of TBPTMH mixed with common metal ions, potentially in containers and pipes, is important. In this work, by using differential scanning calorimetry (DSC) and Phi-Tec adiabatic calorimetry, the effects of CuCl₂, FeCl₃, CuBr_2, and FeBr₃ on the thermal decomposition of TBPTMH were investigated. Adiabatic kinetic analysis was performed and the apparent activation energy (E_a) was calculated by thermodynamic analysis. Time to maximum rise under adiabatic conditions (TMR_ad) and the self-accelerating decomposition temperature (SADT) under different packing qualities were reckoned. It was found that the thermal risk of TBPTMH was increased while mixing these metal ions, especially CuBr₂. To ensure the safety of the substance in process industry, the temperature of TBPTMH in the presence of metal should be governed below 39.48 °C. This work was expected to provide some guidance for improving the process safety of TBPTMH.     

Thermal hazard assessment for synthesis of 3-methylpyridine-N-oxide

The exothermic oxidation of 3-methylpyridine with hydrogen peroxide was analyzed by Reaction Calorimeter (RC1e) in semi-batch operation. Heat releasing rate and heat conversion were studied at different operating conditions, such as reaction temperature, feeding rate, the amount of catalyst and so on. The thermal hazard assessment of the oxidation was derived from the calorimetric data, such as adiabatic temperature rise (ΔT_ad) and the maximum temperature of synthesis reaction (MTSR) in out of control conditions. Along with thermal decomposition of the product, the possibility of secondary decomposition under runaway conditions was analyzed by time to maximum rate (TMR_ad). Also, risk matrix was used to assess the risk of the reaction. Results indicated that with the increase of the reaction temperature, the reaction heat release rate increased, while reaction time and exotherm decreased. With the increase of feeding time, heat releasing rate decreased, but reaction time and exotherm increased. With the amount of the catalyst increased, heat releasing rate increased, reaction time decreased and exothermic heat increased. The risk matrix showed that when the reaction temperature was 70 °C, feeding time was 1 h, and the amount of catalyst was 10 g and 15 g, respectively, the reaction risk was high and must be reduced.     

Research on thermal decomposition characteristics of H foaming agent with different moisture contents

N, N-Dinitroso pentamethylene tetramine, also known as H foaming agent, is a self-reactive chemical substance commonly used in the rubber industry. Decomposition, explosion and combustion may be caused by the presence of fire or high temperature. As a high-risk chemical that is strictly regulated in China, H foaming agent has ever triggered multiple accidents. During the study of the decomposition thermal process of H foaming agent, it was found that the presence of moisture content at different levels had a significant effect on its thermal stability. The thermal characteristics of H foaming agent under different moisture contents was studied through the test means such as adiabatic calorimetry and high-pressure differential scanning calorimetry. Through isothermal calorimetry experiment, it was found that the decomposition of H foaming agent had obvious auto-catalytic characteristics. In the moisture content within the range of 0–40%, with the increase of moisture content, the initial exothermic temperature T_onset of the mixture system of H foaming agent and water decreased, while the time from initial heat release to rapid temperature rise of the reaction system (induction period) was gradually prolonged, and the temperature increment of the reaction system was increased gradually. As the proportion of moisture content in the system increased, the adiabatic temperature rise ΔT_ad of the mixture system of H foaming agent and water gradually decreased, meanwhile the time to maximum rate under adiabatic condition (TMR_ad) gradually decreased. The research results have guiding significance for finding the reasonable moisture content of H foaming agent in the drying process and determining the upper temperature limit during storage and transportation.     

Thermal research on the uncontrolled behavior of styrene bulk polymerization

Thermal runaway can occur during the styrene bulk polymerization process because of easily formed local hotspots resulting from the high viscosity of reactants and the difficulty of heat dissipation. To obtain the thermal hazard characteristics, the polymerization behavior of styrene was investigated using differential scanning calorimetry (DSC) at a scanning rate of β = 2 °C/min. Experimental results showed that the exothermic peaks obtained for heat initiation were different from those obtained when initiator was added. The exothermic peak changed from one to two after the initiator was added. The exothermic onset temperature (T₀) was also reduced. Phi-tech II was utilized to study the bulk polymerization of styrene in an adiabatic environment. The adiabatic temperature rise (ΔT_ad), starting temperature of uncontrolled polymerization (T_star), maximum temperature (T_end), and heat of polymerization (ΔH) under different conditions were acquired. When the dose of the additive was increased, the starting temperature of uncontrolled polymerization (T_star) decreased and the adiabatic temperature rise (ΔT_ad) increased gradually. Severity grading was performed based on the severity evaluation criteria of runaway reaction. The results can help designers decide whether it is necessary to take certain measures to reduce risk.     

Process hazard assessment of energetic ionic liquid with kinetic evaluation and thermal equilibrium

With the continuous development of battery technology, there are new research investments in materials of various parts. In the field of electrolytes, ionic liquids (IL) are considered to be excellent electrolytes and have been widely studied in distinct energy fields. However, it is necessary to pay attention to the safety characteristics of ionic liquids at high temperature due to the application of energy, but there is little research on the reaction and kinetics of ionic liquids. To ensure the safety of ionic liquids, such as high temperature, the common ionic liquid 1-Ethyl-3-methylimidazolium nitrate ([Emim] NO₃) was selected for analysis. The exothermic mode is obtained from the data of differential scanning calorimetry. The basic reaction parameters of [Emim] NO₃ were determined with thermodynamic equation simulation. For ionic liquids in the actual situation, consider adding a heat balance model to estimate its temperature change pattern and find out the hazard temperature and related safety parameters. Temperature changes were estimated by constructing 25.0 g and 50.0 g packages to simulate material reactions and heat transfer in the external environment. The results showed that [Emim] NO₃ had shorter TMR_ad and TCL (<1 day) when the temperature was above 180 °C.     

Relationship between electric spark sensitivity and activation energy of the thermal decomposition of nitramines for safety measures in industrial processes

This study presents a new simple correlation between electric spark sensitivity of nitramines and their activation energies of thermolysis, which are important for safety measures in industrial processes. The new correlation can help to elucidate the mechanism of initiation of energetic materials by electric spark. It can be used to predict the magnitude of electric spark sensitivity of new nitramines, which is difficult to measure. The methodology assumes that electric spark sensitivity of a nitramine with general formula C_aH_bN_cO_d can be expressed as a function of its activation energy of thermal decomposition as well as optimized elemental composition and the contribution of specific molecular structural parameters. The new correlation has the root mean square and the average deviations of 1.37 and 1.09 J, respectively, for 21 nitramines with different molecular structures. The proposed new method is also tested for 16 nitramines so that there is no experimental data of electrostatic sensitivity for them.     

Using thermal analysis with kinetic calculation method to assess the thermal stability of 2-cyanopropan-2-yliminourea

Azo compounds, which are commonly used as initiators and blowing agents, are also typical self-reactive materials capable of undergoing runaway reaction during storage and transportation, which can cause severe fires and accidents. To ensure the thermal safety of azo compounds in the process, transportation, and applications, this study investigated 2-cyanopropan-2-yliminourea, which can also be called V-30. First, thermal decomposition characteristics under the non-isothermal conditions were obtained using differential scanning calorimetry. Second, the collected data were combined with a mathematical model to evaluate the primary thermal hazard during the process for V-30. Then, based on a heat-transfer model, the self-accelerating decomposition temperature (SADT) was extrapolated for consideration and non-consideration of consumption of chemicals. The results showed that SADT of V-30 was less than 80 °C. Therefore, it is essential to avoid a temperature beyond SADT or the cooling system will fail. The influence of consumption was also considered for SADT in this study.     

Thermal hazard analysis of triacetone triperoxide (TATP) by DSC and GC/MS

Thermal degradation of triacetone triperoxide (TATP) was studied using differential scanning calorimetry (DSC) and gas chromatography/mass spectrometry (GC/MS). TATP, a potential explosive material, is powerful organic peroxide (OP) that can be synthesized by available chemicals, such as acetone and hydrogen peroxide in the laboratory or industries. The thermokinetic parameters, such as exothermic onset temperature (T₀) and heat of decomposition (ΔH_d), were determined by DSC tests. The gas products from thermal degradation of TATP were identified using GC/MS technique.In this study, H₂O₂ was mixed with propanone (acetone) and H₂SO₄ catalysis that produced TATP. The T₀ of TATP was determined to be 40 °C and E_a was calculated to be 65 kJ/mol. A thermal decomposition peak of H₂O₂ was analyzed by DSC and two thermal decomposition peaks of H₂O₂/propanone were determined. Therefore, H₂O₂/propanone mixture was applied to mix acid that was discovered a thermal decomposition peak (as TATP) in this study. According to risk assessment and analysis methodologies, risk assessment of TATP for the environmental and human safety issue was evaluated as 2-level of hazard probability rating (P) and 6-level of severity of consequences ratings (S). Therefore, the result of risk assessment is 12-point and was evaluated as “Undesirable” that should be enforced the effect of control method to reduce the risk.     

Thermal hazard accident investigation of hydrogen peroxide mixing with propanone employing calorimetric approaches

Hydrogen peroxide (H₂O₂), historically, due to its broad applications in the chemical industries, has caused many serious fires and explosions around the world. Its thermal hazards may also be incurred by an incompatible reaction with other chemicals, and a runaway reaction may be induced in the last stage. This study applied thermal analytical methods to explore the H₂O₂ leading to these accidents by incompatibility and to discuss what might be formed by the upset situations. Thermal hazard analysis contained a solvent, propanone (CH₃COCH₃, so-called acetone), which was deliberately selected to mix with H₂O₂ for investigating the degree of thermal hazard. Differential scanning calorimetry (DSC) and vent sizing package 2 (VSP2) were employed to evaluate the thermal hazard of H₂O₂. The results indicated that H₂O₂ is highly hazardous while mixed with propanone, as a potential contaminant. The time to maximum rate (TMR) was used as emergency response time in the chemical industries. Therefore, TMR of H₂O₂ was calculated to be 70 min for runaway reaction (after T₀) and TMR of H₂O₂/propanone was discovered to be 27 min only. Fire and explosion hazards could be successfully lessened if the safety-related data are properly imbedded into manufacturing processes.     

Comparisons of TGA and DSC approaches to evaluate nitrocellulose thermal degradation energy and stabilizer efficiencies

This study investigated the thermal degradation energy (activation energy, E_a) for nitrocellulose (NC) with low nitrogen content of 11.71 mass%, so-called NC3, by using two different kinds of thermal analysis instruments: thermogravimetric analyzer (TGA) and differential scanning calorimetry (DSC). A comparison of E_a for various nitrogen content NC samples at two scanning rates (5 and 10 °C min^?1) tested by TGA and DSC is also discussed in this paper. Meanwhile, our aim was to analyze the anti-degradation of E_a for NC with high nitrogen content, as so-called NC1. Thermal stability for NC1 with diphenylamine (DPA) was tested via DSC with 10 DPA concentrations in weights of 0, 0.25, 0.50, 0.75, 1.0, 1.25, 1.50, 1.75, 2.0, and 3.0 mass%. Experimental results indicated that E_a of NC3s was 319.91 kJ mol^?1. Moreover, that while dosing DPA into NC1 the best recipe could be employed to avoid any violent NC1 runaway and also can be used to distinguish the differences of thermal decomposition E_a between NC with different nitrogen contents. This study established a fast and efficient procedure for thermal decomposition properties of NC, and could be applied as an intrinsically safer design during relevant operations.     

Analytical modelling of hydrocarbon pool fires: Conservative evaluation of flame temperature and thermal power

As well known, risk is a combination of probability and consequences of an accident. In analyzing the consequence of accidental hydrocarbon fires and the potential for domino effects, the evaluation of the flame extent and temperature are of the utmost importance. Since the primary effects of pool fires are connected to thermal radiation and issues of interplant/tank spacing employees’ safety zones, firewall specifications are to be addressed on the basis of a proper consequence analysis. By means of real scale experimental tests it was verified that both the thermal power and the flame temperature, T_f, increase as the pool area increases, up to reach maximum values in connection with a “critical pool dimension”. Dealing with pool areas higher than the critical one, experimental results, performed by different researchers at different scales, show a decrease of T_f. An in-depth analysis of the different concurring phenomena connected to a pool fire development allowed identifying the limiting step controlling the flame temperature. In fact, the trend of T_f is mainly determined by the increasing difficulty of oxygen diffusion within the internal bulk of gaseous hydrocarbons. In this article, we propose a novel pool fire modelling approach based on the simplified physical phenomena occurring in a circular turbulent diffusion fire and suitable to provide a theoretical insight into the above-mentioned experimental trends and to obtain the maximum values of the flame temperature and of the thermal power.The geometry of the pool is dictated by the surroundings (i.e., diking) and the analytical models here presented were successfully applied to the common situation of circular pools.However, it must be remarked that the developed model, matching fairly well experimental data for different hydrocarbons, can be applied in modelling similar scenarios characterized by different geometric or environmental conditions (e.g. road and rail tunnel fires).     

The application of kinetics based simulation method in thermal risk prediction of coal

Coal spontaneous combustion is one of the major natural disasters faced in coal mines. The accurate prediction of the thermal risk of coal is of great importance. However, there isn't a widely accepted approach to get the oxidation process of coal that under adiabatic condition or in a specific environment under mine at present. To demonstrate whether the advanced kinetics simulation method could be employed to obtain the accurate oxidation process of coal for determining the coal's thermal risk in the mine design phase and mining phase, DSC experiments were conducted by C80 micro-calorimeter to get the heat behavior of coal, based on which the kinetic parameters can be solved and the oxidation process of coal can be predicted.The results showed that the kinetics based simulation method was successfully used to predict the adiabatic temperature rise process of coal for risk prediction. The deviation between the predicted curve and tested curve that obtained by adiabatic test is small enough to be accepted. Kinetics based simulation method is a promising candidate, instead of adiabatic test, to assess the propensity of coal to spontaneous combustion, which can play an important role in the design phase of the mine and mining area. Moreover, through establishing the heat balance equation of residual coal and with the aid of kinetics based simulation method, the oxidation process of coal that in the suffocation zone of the gob was also accurately predicted. According to the index t₇₀ (the time required for coal to reach 70 °C) and v_min (the lower limit of the advancing speed of the working face) obtained from the predicted curve, the thermal risk of coal was predicted to guide the further adjustment of the advancing speed of the working face, the amount of the injected mud and the determination that whether to add other fire prevention measures. Kinetics based simulation method, be of great practical importance in risk prediction of coal that in the gob, can be also used as a convenient tool to guide the safe production in the actual mining process.     

Thermodynamic method for the prediction of solid CO2 formation from multicomponent mixtures

The increase in GHG concentration has a direct effect on global climate conditions. Among the possible technologies to mitigate GHG emissions, CCS is being accepted to gain emission reduction. Such technology also involves cryogenic CO₂ capture processes based on CO₂ freeze-out or where the formation of solid CO₂ must be avoided. Captured CO₂ is usually transported in pipelines for the reinjection.The risk associated to the release of CO₂ is due to the changing temperatures and pressures the system may experience, which can lead to the deposition of solid CO₂ where it must be avoided. Prolonged exposure to dry ice can cause severe skin damage and its resublimation could pose a danger of hypercapnia. It is, thus, necessary to build up a tool able to predict the conditions in which CO₂ can freeze-out.A thermodynamic methodology based on cubic EoSs has been developed which is able to predict solid–liquid–vapor equilibrium of CO₂ mixtures with n-alkanes or H₂S which are usually found in equipment for acidic gas, mainly natural gas, treatment.The focus is a detailed analysis of the method performances when more than two components are present since, for such a case, literature does not provide significant modeling results.     

Calorimetric behaviors of N2H4 by DSC and superCRC

The objective of this study is to obtain information about the thermal decomposition behaviors of hydrazine (N₂H₄) caused by metals, using differential scanning calorimeter (DSC) and SuperCRC. The DSC measurements revealed that the exothermic reactions of N₂H₄ were caused by the reaction conditions such as the type of cells; the T_DSC with a gold pan is 485.2 K and that with a glass capillary is 620.5 K. Besides, the activation energy of the thermal decomposition of N₂H₄, calculated from the Kissinger and Ozawa methods, were found to be about 38±2 kJ mol⁻¹ in the gold pan and 141±8 kJ mol⁻¹ in the glass capillary. Moreover, a heat flow profile was observed with SuperCRC during the mixing of N₂H₄ and the metal ion solution at 298 K. The maximum heat flow was related to the metal ion oxidative characters. The higher oxidative characters would provide a faster acceleration for the exothermic behavior than the lower oxidative ions. Based on this study, Mn(VII) and Cr(VI) were considered to exhibit strongly oxidative characteristics during mixing with N₂H₄.