粉煤灰砖块对磷酸盐的吸附特性

以建筑废料粉煤灰砖块为吸附剂材料,通过静态吸附实验研究其对磷酸盐的吸附特征,以及磷酸盐初始浓度、吸附剂投加量、pH等因素对吸附反应的影响。Langmuir、Freundlich和Temkin等温模型的分析发现,Langmuir等温式方程最适合描述吸附过程,对磷酸盐的理论饱和吸附容量为44.62 mg/g。利用伪一级动力学模型、伪二级动力学模型和颗粒内扩散模型考察了吸附过程特征,其中伪二级动力学模型为最适于描述粉煤灰砖块对磷酸盐的吸附过程的动力学模型。通过颗粒内扩散模型、Bangham方程及Boyd模型对吸附动力学机理进行的探讨表明,颗粒内扩散速率不是粉煤灰砖块吸附磷酸盐反应的惟一速率控制步,膜扩散速率和颗粒内扩散速率共同影响着吸附反应速率。磷酸盐浓度较低时主要是膜扩散限制吸附反应速率,而磷酸盐浓度较高时则颗粒内扩散成为速率控制步。研究证明,粉煤灰砖块粉末作为湿地基质具有对磷酸盐很强的吸附能力,在减少了固体废弃物的数量的同时又可以实现水污染控制的目的。     

响应面分析法优化造纸污泥吸附剂除磷工艺

以造纸厂废水污泥为原料,采用微波加热法制备造纸污泥吸附剂。利用制备的造纸污泥吸附剂对模拟含磷废水进行了吸附研究,探讨了吸附时间、投加量、pH值、转速和温度等因素对除磷效果的影响,并采用响应面设计法优化吸附工艺条件。结果表明,获得了最佳除磷工艺条件为吸附时间97 min,投加量6.9 g/L,pH=6,转速200 r/min,温度30℃,在此条件下磷的去除率可达99%以上。因此,造纸污泥吸附剂对磷的吸附效果良好,具有重要的实际应用价值。     

生物质材料预处理餐饮废水

采用4种廉价的生物质材料（水葫芦、柚子皮、木屑、核桃壳）用于餐饮废水的预处理。通过静态烧杯实验，研究了各生物质材料预处理废水的效果及最佳处理条件。结果表明，生物质材料对废水中COD的去除率均在45％以上，油脂吸附量为4～16mg／g，最优吸附材料为水葫芦，COD去除率达65％，油脂吸附量为16mg／g；水葫芦和柚子皮的最佳处理条件为：粒径〈0．2mm，投加量为20g／L，废水pH为4，处理时间为2h，温度为20℃；木屑和核桃壳的最佳实验条件为：粒径〈0．2mm，投加量为28g／L，pH为2，处理时间为2．5h，温度为20℃。生物质对餐饮废水的预处理，为废水中大量有机物和废弃油脂的去除提供了新思路和途径。     

褐煤对废水中酸性红B的吸附去除

选用褐煤作为廉价吸附剂,脱除模拟废水中染料酸性红B。研究了褐煤对废水中酸性红B的吸附动力学、等温吸附模式,考察了pH、褐煤投加量以及离子强度(NaCl)对吸附效果的影响。结果表明,吸附动力学较好地符合准二级速率方程(R2=1.000),并且以化学吸附为主;吸附等温式满足Langmuir方程(R2=0.986),最大单分子层吸附量为42 mg/g;废水中染料的去除率随溶液pH的减小而明显增加,在pH=1时,去除效果最好,证实吸附过程存在静电吸引及化学键合;在一定条件下,溶液中酸性红B的去除率随褐煤投加量增加而增加;吸附效果随溶液中离子强度(NaCl)的增加而增强。说明褐煤可以作为一种廉价吸附材料,用于处理含染料废水。     

Phosphate removal from wastewater using aluminium oxide as adsorbent

The development and manufacture of an adsorbent to remove phosphate for the prevention of eutrophication in lakes is very important. The use of aluminium oxide (alumina) as an organic adsorbent to remove phosphate from wastewater has been investigated. The characteristics of this absorption process were investigated to determine the important parameters, such as the pH and the aluminium ion concentration. Moreover, chemical treatment methods to enhance the adsorption capacity of alumina were tested. Dynamic studies and equilibrium adsorption isotherm studies were conducted to determine the adsorption capacity and efficiency. The experimental results indicate that it is necessary to increase the temperature above 500°C in order to obtain a high-capacity adsorbent, and alumina treated with acid or calcium or magnesium has a larger adsorption capacity for phosphate than untreated adsorbent. Moreover, the adsorption of phosphate was enhanced at a lower pH and a higher aluminium ion concentration, and a simple Freundlich isotherm could express the equilibrium adsorption isotherm, and the intragranular diffusion controlling model was used to test the dynamic studies. These findings have important implications for the application and development of aluminium oxide as a prospective adsorbent.     

铁基膨润土对水中磷酸根的吸附热力学及动力学研究

采用铁盐改性制得铁基膨润土,研究了其对水中磷酸根的吸附性能及影响因素,结果表明,通过对膨润土的改性提高了磷的去除率,含磷废水初始pH值的大小对磷的去除率影响不大,初始浓度越低越有利于磷的去除。磷的去除率随改性膨润土的投加量增大而提高,随温度升高而增大。进一步研究表明,改性膨润土对磷的吸附是吸热反应,其吸附等温线可采用Langmuir等温吸附方程拟合;改性膨润土对磷的吸附是快速吸附,在20 min内,磷去除率达70%以上,符合准二级吸附动力学模型。     

Effect of sewer headspace air-flow on hydrogen sulfide removal by corroding concrete surfaces

Hydrogen sulfide adsorption and oxidation by corroding concrete surfaces at different air-flows were quantified using a pilot-scale sewer reactor. The setup was installed in an underground sewer research station with direct access to wastewater. Hydrogen sulfide gas was injected into the headspace of the sewer reactor once per hour in peak concentrations of approximately 500 ppmv. The investigated range of sewer air-flows was representative for natural ventilated sewer systems, and covered both laminar and turbulent conditions. The experiments demonstrated a significant effect of sewer air-flow on the kinetics of hydrogen sulfide removal from the sewer headspace. From the lowest to the highest air-flow investigated, the rate of adsorption and oxidation increased more than threefold. At all air-flows, the reaction kinetics followed a simple n-th order rate equation with a reaction order of 0.8. The effect of air-flow on hydrogen sulfide adsorption and oxidation kinetics was quantified by a simple empirical equation.     

Removal mechanism of endosulfan sorption onto wood charcoal

Endosulfan is among the most widely used pesticides in developing countries and other parts of the world and has been found to contaminate various parts of the environment, including drinking water sources. In an earlier study to find a suitable adsorbent to remove endosulfan, wood charcoal was found to give promising results. In the present study, the process controlling the rate of endosulfan sorption onto wood charcoal and the mechanism of removal were examined using various methodologies. Both film and pore diffusion coefficients were determined, and the linearity of the rate constants of adsorption with initial endosulfan concentrations revealed the process to be controlled by film diffusion. This was supported by the linear fit of the rate constants with the inverse of the diameter of adsorbent particles and the change in adsorption rates with agitation speed. Multiple interruption tests also revealed that endosulfan sorption onto wood charcoal is controlled by film diffusion. The increase in reaction rate constant with temperature and isosteric heat of adsorption in the range of -2.655 to 5.185 kcal/mol implied that the endosulfan removal process was endothermic in nature. The activation energy of 2.33 kcal/mol, which was less than 12 kcal/mol, revealed that the removal mechanism could be attributed to physisorption with a major contribution of van der Waals and electrostatic forces.     

粉末活性炭对三烯丙基异氰脲酸酯的吸附性能简

用静态吸附法考察粉末活性炭对水中三烯丙基异氰脲酸酯（CAIC）的吸附行为，采用单因素分析法对活性炭吸附化工废水中TAIC的工艺条件进行研究。实验结果表明，在TAIC模拟废水中，其TAIC初始浓度为800 mg/L，pH为7，在温度为298 K、转速为150 r/min的条件下，当活性炭的投加量达到4.4 g/L，吸附反应时间为50 min时，TAIC的去除效率最高为96.17%；对于实际废水，其TAIC初始浓度为1 500 mg/L，溶液pH为3，在温度为298 K、转速为150 r/min的条件下，当活性炭投加量达到10 g/L，吸附反应时间为2 h时，TAIC的去除效率最高为46.8%。这也是由于实际废水组分复杂，其他有机物存在一定的吸附竞争机制。     

改性粉煤灰处理低浓度含磷废水的研究

以酸改性粉煤灰为吸附剂,处理低质量浓度(1 mg/L左右)磷酸盐溶液,探讨了改性剂的种类、改性剂用量、吸附剂用量、反应时间、pH以及温度对除磷效果的影响.结果表明:(1)经过酸改性后粉煤灰的磷去除率显著提高,而且硫酸改性粉煤灰的除磷效果更好,磷去除率最高可达97.68％.(2)最佳条件:选择硫酸用量为5 mL/g进行改性,硫酸改性粉煤灰投加量为2.0g,反应时间为60 min,pH为7.2～10.8,温度为25℃(即室温).(3)改性粉煤灰对磷的吸附更符合Freundlich吸附等温模型,既有物理吸附,也有化学吸附,并以Ca、Mg氧化物与磷形成磷的沉淀物为主.     

连续式生物吸收工艺脱除二氧化硫

运用连续式生物吸收处理工艺,以废糖蜜发酵液作为碳源进行了微生物法去除SO2气体的研究,在简单粗放的实验条件下,研究了脱硫脱硫弧菌对较大气量SO2气体的去除效果,并对产物H2S在第二级生物反应器中的去除率进行了测定。实验结果表明,随着进气量由0.18 m3/h增大至5 m3/h,脱硫率会降低,但是随之提高搅拌速度和补料速度后,脱硫率又恢复到较高水平,当搅拌速度为590 r/min时,5 L生物反应液可以处理5 m3/h的SO2气体,1#反应器SO2去除率和2#反应器H2S去除率分别达到92%和98%以上。在气量增至5 m3/h时,1#和2#反应器补料流速分别为175 mL/h和200 mL/h时,没有亚硫酸盐和硫化物的积累,pH值和菌体浓度稳定,系统运行良好。     

纳米有机膨润土对苯酚的吸附性能研究

通过对天然膨润土改性,制备纳米有机膨润土并用于吸附苯酚,探讨了吸附时间、溶液pH、纳米有机膨润土投加量等因素对苯酚吸附的影响。结果表明,吸附在5 min内快速达到平衡,溶液pH可以影响苯酚在溶液中的状态,是影响苯酚吸附性能的重要因素。纳米有机膨润土吸附苯酚的过程可用伪二级反应动力学方程来描述,伪二级吸附速率常数为1.3 g/(mg.min)。吸附等温线符合Langmuir等温方程,在25℃时,Langmuir理论最大吸附容量可达到536.32 mg/g,吸附热力学参数表明吸附过程是自发的、放热的物理吸附过程。     

利用厌氧菌发酵产物处理含铅废水及机理研究

针对传统方法去除废水中重金属铅的缺陷,利用4株厌氧微生物的发酵产物,在不同投加量、pH、温度和反应时间下研究该产物的除铅效果。通过正交实验确定了微生物发酵产物对含铅废水处理的最佳反应条件为:发酵产物投加量为0.5 g,反应时间为20 min,pH=6,温度20℃,铅的去除率99.4%以上,并用蓄电池厂的实际废水进行验证实验,获得相同的效果;同时通过扫描电子显微镜和X-射线能量散射光谱分析厌氧细菌代谢的混合物成分,对去除机理进行了初步探讨,为生物技术处理含铅废水提供了一种新方法和理论依据。     

Waste Fe(III)/Cr(III) hydroxide as adsorbent for the removal of Cr(VI) from aqueous solution and chromium plating industry wastewater

Fe(III)/Cr(III) hydroxide, a waste material from the fertilizer industry, has been used for the adsorption of Cr(VI) from aqueous solution, over a range of initial metal ion concentrations (5-30 mg litre(-1)), agitation times (1-180 min), adsorbent dosages (100-1200 mg per 50 ml), temperatures (24, 29 and 38 degrees C) and pH values (4.5-10). The adsorption of Cr(VI) increased with the initial concentration of Cr(VI) and with temperature. The process of uptake follows both the Langmuir and the Freundlich isotherm models. The applicability of Lagergren and empirical kinetic models has also been investigated. Almost quantitative removal of Cr(VI) at 10 mg litre(-1) in a 50-ml solution by 500 mg of adsorbent was found at an equilibrium pH of 5.6. The efficiency of chromium removal was also tested using wastewater from the chromium plating industry.     

Combustion characteristics of spent catalyst and paper sludge in an internally circulating fluidized-bed combustor

Combustion of spent vacuum residue hydrodesulfurization catalyst and incineration of paper sludge were carried out in thermo-gravimetric analyzer and an internally circulating fluidized-bed (ICFB) reactor. From the thermo-gravimetric analyzer-differential thermo-gravimetric curves, the pre-exponential factors and activation energies are determined at the divided temperature regions, and the thermo-gravimetric analysis patterns can be predicted by the kinetic equations. The effects of bed temperature, gas velocity in the draft tube and annulus, solid circulation rate, and waste feed rate on combustion efficiency of the wastes have been determined in an ICFB from the experiments and the model studies. The ICFB combustor exhibits uniform temperature distribution along the bed height with high combustion efficiency (>90%). The combustion efficiency increases with increasing reaction temperature, gas velocity in the annulus region, and solid circulation rate and decreases with increasing waste feed rate and gas velocity in the draft tube. The simulated data from the kinetic equation and the hydrodynamic models predict the experimental data reasonably well.     

PAC混凝沉降法处理陶瓷废水操作条件的优化

采用PAC混凝沉降法对陶瓷废水进行处理,考察PAC用量、搅拌强度、搅拌时间、进水pH和沉降时间对处理效果的影响,获得优化的操作条件。实验表明:水样的脱色率、浊度去除率和悬浮物去除率随着PAC用量、搅拌强度、搅拌时间和沉降时间的增大和进水pH的降低而呈现增大的趋势;最佳操作条件为:当废水量小、处理时间充足时,选用PAC用量为12 mg/L、搅拌强度为中速、搅拌时间为10 min、进水pH为6、沉降时间为2 h,此条件下水样的脱色率、浊度去除率和悬浮物去除率分别达到95.6%、95.7%和85.6%;当废水量大、处理时间不充足时,选用PAC用量为60 mg/L,沉降时间为30 min,此条件下水样的脱色率、浊度去除率和悬浮物去除率分别达到94.1%、93.4%和84.4%。证明混凝法对于去除陶瓷废水中的悬浮与胶体颗粒均是有效的。     

垃圾焚烧飞灰对染料（亚甲基蓝）的吸附性能

以垃圾焚烧飞灰为吸附剂对亚甲基蓝进行了吸附脱色实验。主要探讨了飞灰粒径、用量、温度、pH值和初始浓度等因素对亚甲基蓝吸附的影响，同时分析了吸附上清液中重金属Pb和Cr的浸出毒性。研究结果表明，在25—45℃、pH值2～12、飞灰用量1～5g范围内，经过180min吸附，亚甲基蓝的脱色率都达75％以上，最高可达99．46％。实验还得出，除重金属Pb外，吸附上清液中重金属的浸出量远远低于《危险废物鉴别标准浸出毒性鉴别》的限定值。因此，若能降低重金属Pb的浸出，飞灰将具有应用于处理染料废水的巨大潜力。     

Kinetics and stoichiometry of aerobic sulfide oxidation in wastewater from sewers-effects of pH and temperature.

Kinetics and stoichiometry of aerobic chemical and biological sulfide oxidation in wastewater from sewer networks were studied. In this respect, the effects of temperature and pH were investigated in the ranges 10 to 20 degrees C and 5 to 9, respectively. The temperature dependency of sulfide oxidation kinetics was described using an Arrhenius relationship. The effect of pH on the rate of chemical sulfide oxidation is related to the dissociation of hydrogen sulfide (H2S) to hydrogen sulfide ion (HS(-)), with HS(-) being more readily oxidized than H2S. Biological sulfide oxidation exhibited the highest rates at ambient wastewater pH, and the reaction was inhibited at both low and high pH values. Chemical sulfide oxidation was found to produce thiosulfate and sulfate, while elemental sulfur was the main product of biological sulfide oxidation. Based on the investigations, general rate equations and stoichiometric constants were determined, enabling the processes to be incorporated to conceptual sewer process models.     

Use of carbonised beet pulp carbon for removal of Remazol Turquoise Blue-G 133 from aqueous solution

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g^?1at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.     

Combustion Characteristics of Spent Catalyst and Paper Sludge in an Internally Circulating Fluidized-Bed Combustor

Abstract

Combustion of spent vacuum residue hydrodesulfurization catalyst and incineration of paper sludge were carried out in thermo-gravimetric analyzer and an internally circulating fluidized-bed (ICFB) reactor. From the thermogravimetric analyzer-differential thermo-gravimetric curves, the pre-exponential factors and activation energies are determined at the divided temperature regions, and the thermo-gravimetric analysis patterns can be predicted by the kinetic equations. The effects of bed temperature, gas velocity in the draft tube and annulus, solid circulation rate, and waste feed rate on combustion efficiency of the wastes have been determined in an ICFB from the experiments and the model studies. The ICFB combustor exhibits uniform temperature distribution along the bed height with high combustion efficiency (>90%). The combustion efficiency increases with increasing reaction temperature, gas velocity in the annulus region, and solid circulation rate and decreases with increasing waste feed rate and gas velocity in the draft tube. The simulated data from the kinetic equation and the hydrodynamic models predict the experimental data reasonably well.