Goods in the Anthroposphere as a Metal Emission Source A Case Study of Stockholm,Sweden

The aim of this study was to quantify the diffuse emissionsduring use of metal containing goods in the capital of Sweden,Stockholm. The following metals were studied: Cadmium (Cd), Chromium (Cr), Copper (Cu), Lead (Pb), Mercury (Hg), Nickel (Ni) and Zinc (Zn).A major part of the metals are found in a protected environmentwhere degrading processes like corrosion are most limited. However, during the lifetime of some goods the metal release to the environment is significant. The quantitatively most dominant emissions were found for Cu and Zn. The tap water system and roofs/fronts (Cu) represent goods with large exposedareas but with relatively small release rates per unit. In contrast, brake linings, aerial lines and electrical grounding (Cu) and tyres, brake linings and chemicals (Zn) are allgoods with high release rates but mostly limited exposed stocks.High yearly emissions are also found for Pb, ammunition andsinkers dominate the calculated emissions totally. For Cr and Ni, stainless steel represent the major part of the stocks, butcorrosion was estimated to give only a minor contribution to the emissions. Potential emission sources, i.e. stabilisers,pigments and plated goods dominate the exposed Cd stock. Theseemissions were not quantified due to lack of data. Hg is currently phased out, but one major source of emission, i.e. the use of amalgam, will be continuously significant for several decades. The importance of the traffic sector is obvious. The emissionsfrom brake linings (Cu, Zn and Pb), tyres (Zn, Pb, Cr and Ni)and asphalt wear (Cu, Zn, Cr, Ni and Pb) are all of large importance for the total emission from respectively metal.     

Potential emissions from two mechanically-biologically pretreated (MBT) wastes

The interaction of parameters determining the potential emissions of two different mechanically-biologically pretreated municipal solid wastes (MBT wastes) is elucidated in this work. The origins of the wastes are Germany and Sweden. By means of lab-scale experiments, increased stabilisation through composting is preferably determined by a decrease in respiration activity. Concurrently, the stabilisation is verified for the leachates by a decrease in COD, DOC, and BOD(5). Total organic carbon content reflects stabilisation less accurately. FT-IR and thermal analytical methods add valuable information about the state of degradation, especially when several distinct thermal parameters are taken into account. Mobility of Cr, Ni, Pb, and Zn produced by a batch leaching test with deionized water is reduced by the pretreatment of both materials. Mobility of copper unambiguously increased. A principle component analysis (PCA) of membrane fractionated leachates indicates an affinity of Cu to mobile humic acids or dissolved organic carbon. High Cr, Zn, and Ni contents in the solid co-occur with high contents of solid humic acids. To a lesser extent, this is also true for solid Cd, Cu, and Pb contents. Due to differences in required landfilling conditions, actual emissions and after-care phase length will depend on whether each waste is landfilled in Germany or Sweden.     

气化炉渣的重金属浸出特性及化学形态分析

分别采用硫酸硝酸法、水平振荡法和醋酸缓冲溶液法制取气化炉渣的浸出液，考察了不同提取方式对浸出液中重金属质量浓度的影响。采用改进BCR连续提取法对气化炉渣中的重金属Cr，Zn，Cu，Pb，Ni，As，Cd的化学形态进行了分析。实验结果表明：煤气化工艺中的气化炉渣属第Ⅰ类一般工业固体废物;在3种提取方式中，醋酸缓冲溶液法的重金属浸出种类最多，且浸出量最大;Cd和Cr对环境具有较高的潜在危害性，Cu次之，Zn，Pb，Ni，As主要以残渣态形式存在，对环境的直接危害性较低。     

Metal fractionation in soil profiles at automobile mechanic waste dumps.

Soil profiles at five automobile mechanic waste dumps in Port-Harcourt, Nigeria were investigated to assess the spatial distribution, chemical speciation, and likely mobility of Cd, Cu, Pb, Zn, Cr and Ni in the soil as a function of the soil properties. A sequential fractionation protocol was used that generated six different fractions into which soil metal could partition. Cadmium was associated with non-residual fractions at surface horizons, but at lower depths it was in the residual fractions. Copper and Cr partitioned into organic and residual fractions, while Pb was associated with an Fe-Mn oxide fraction and the residual fractions. Zinc in surface horizons partitioned into an Fe-Mn oxide fraction and a fraction that captured carbonate-bound species, but in subsurface horizons, it was mainly in the residual fractions. Ni was predominantly found in the residual fractions. Mobility factors were calculated, and their values tended to decrease with increasing profile depth, indicating that these metals are relatively mobile in the surface horizons compared the subsurface except for chromium in the 15-30 cm depths. The mobility factors for the heavy metals follow the order: Cd > Zn > Pb > Cu > Cr > Ni. The results suggest that there is serious contamination hazard with Cd, Pb, and Zn in the soil profiles.     

Heavy metals in source-separated compost and digestates

The production of compost and digestate from source-separated organic residues is well established in Europe. However, these products may be a source of pollutants when applied to soils. In order to assess this issue, composts, solid and liquid digestates from Switzerland were analyzed for heavy metals (Cd, Co, Cr, Cu, Ni, Pb and Zn) addressing factors which may influence the concentration levels: the treatment process, the composition, origin, particle size and impurity content of input materials, the season of input materials collection or the degree of organic matter degradation.Composts (n = 81) showed mean contents being at 60% or less of the legal threshold values. Solid digestates (n = 20) had 20–50% lower values for Cd, Co, Pb and Zn but similar values for Cr, Cu and Ni. Liquid digestates (n = 5) exhibited mean concentrations which were approximately twice the values measured in compost for most elements. Statistical analyses did not reveal clear relationships between influencing factors and heavy metal contents. This suggests that the contamination was rather driven by factors not addressed in the present study.According to mass balance calculations related to Switzerland, the annual loads to agricultural soils resulting from the application of compost and digestates ranged between 2% (Cd) and 22% (Pb) of total heavy metal loads. At regional scale, composts and digestates are therefore minor sources of pollution compared to manure (Co, Cu, Ni, Zn), mineral fertilizer (Cd, Cr) and aerial deposition (Pb). However, for individual fields, fertilization with compost or digestates results in higher heavy metal loads than application of equivalent nutrient inputs through manure or mineral fertilizer.     

An assessment of municipal solid waste compost quality produced in different cities of India in the perspective of developing quality control indices

A study was conducted to investigate physico-chemical properties, fertilizing potential and heavy metal polluting potentials of municipal solid waste composts produced in 29 cities of the country. Results indicated that except a very few samples, all other samples have normal pH and EC. Organic matter as well as major nutrients N and P contents in MSW composts are generally low as compared to the composts prepared from rural wastes. Heavy metal contents in composts from bigger cities (>1 million population) were higher by about 86% for Zn, 155% for Cu, 194% for Cd, 105% for Pb, 43% for Ni and 132% for Cr as compared to those from smaller cities (<1 million population). Composts prepared from source separated biogenos wastes contained, on average, higher organic matter (by 57%), total N (by 77%) and total P (by 78%), but lower concentrations of heavy metals Zn (by 63%), Cu (by 78%), Cd (by 64%), Pb (by 84%), Ni (by 50%), and Cr (by 63%) as compared to those prepared from mixed wastes. Partial segregation at the site of composting did not improve quality of compost significantly in terms of fertilizing parameters and heavy metal contents. Majority of MSW composts did not conform to the quality control guideline of ‘The Fertilizer (Control) Order 1985’ in respect of total organic C, total P, total K as well as heavy metals Cu, Pb and Cr. In order to enable the relevant stakeholders to judge overall quality, a scheme has been proposed for the categorization of composts into different marketable classes (A, B, C, and D) and restricted use classes (RU-1, RU-2, and RU-3) on the basis their fertilizing potential and as well as potential for contaminating soil and food chain. Under the scheme, ‘Fertilizing index’ was calculated from the values of total organic C, N, P, K, C/N ratio and stability parameter, and ‘Clean index’ was calculated from the contents of heavy metals, taking the relative importance of each of the parameters into consideration. As per the scheme, majority of the compost samples did not belong to any classes and hence, have been found unsuitable for any kind of use. As per the regulatory limits of different countries, very few compost samples (prepared from source separated biogenos wastes) were found in marketable classes (A, B, C and D) and some samples (11–14) were found suitable only for some restricted use.     

Effect of nine years of animal waste deposition on profile distribution of heavy metals in Abeokuta,south-western Nigeria and its implication for environmental quality

Uncontrolled deposition of waste from animal farms is a common practice in south-western Nigeria, and the presence of heavy metals in soil constitutes environmental and health hazards by polluting the soil, ground water, adjoining streams and rivers. The study investigated the profile distribution of Mn, Pb, Cd, Zn, Fe, Cu, Ni and Cr in some tropical Alfisols in south-western Nigeria after nine years disposal of animal wastes. The amount of these metals in the soil horizons was high enough to cause health and phytotoxic risks. All the metals except Zn and Cr increased down the profile, while Mn, Pb, Cd, Fe, Cu and Ni accumulated at 80–120 cm depth. The increment of these metals at this depth over the top soil were 26%, 143%, 72%, 47%, 328% for Mn, Pb, Cd, Cu and Ni, respectively. It thus, shows their mobility and the possibility of polluting ground water. The Mn content at the poultry and cattle waste sites increased by 127% and 25%, respectively over the control, while that of cattle and swine dump site for Cd content were 9.82 and 15.63 mg kg^?1, respectively. Lead content also increased by 8.52 and 5.25 mg kg^?1, respectively.There was the accumulation of Zn and Cu at the swine dump site while the cattle dump site had the highest amounts of nickel and chromium. The least amount of Fe was recorded at the swine waste dump site. The reduction in organic matter with depths together with the reduced pH might have favored the mobility of the metals. The ranking of pollution among the sites was poultry > swine > cattle > sheep and could be due to the type of ration fed, the vaccination programmes, sanitation programmes and other management practices.     

Urban Metal Flows – A Case Study of Stockholm. Review and Conclusions

Metals have rapidly accumulated in the anthroposphere, especiallyin urban areas, indicating possible environmental and resource problems. Here, Stockholm City was chosen for a case study of urban metal flows, i.e. metal inflow to, metals in the stock of,and metal outflow from the anthroposphere to the biosphere. Themetal stock of Stockholm is large and still growing. The large amounts of metals in the solid waste fraction totally dominatethe outflow from the city. For major parts of the stock, the emissions from goods in use are negligible. There are, however,goods applications corresponding to significant emissions: e.g. the traffic sector (Cu, Zn, Cr, Ni, Pb), the tapwater system (Cu), roofs/fronts or other metal surfaces (Cu, Zn). Today's known metal flows from the anthroposphere of Stockholm to the biosphere and sewage sludge are quantitatively dominated by Zn(34 ton y^-1) and Cu (14 ton y^-1). Historical and present emissions have resulted in high metal concentrations insediments (especially Cd, Hg and Pb, but also Cu and Zn), groundwater (Cu, Hg) and in soils (Hg, Cu, Pb). At present theannual median concentrations are below the Swedish limits for metals in sewage sludge, even if the safety margins aresmall for Cd, Hg and to some extent Cu. The flows of Cu and Zn to Stockholm soils are high with a significant accumulationindicating an environmental impact in a longer time perspective.High levels of metals in surface sediments in the waterenvironments reflects an ongoing input where these metals aretransported from known (Cu, Zn) and or partly unknown (Cd, Hg, Pb) sources. In future urban areas, monitoring of metal flows must be performed both in the anthroposphere and the biospherein order to have a pro active approach to urban environmentalproblems and to get prompt answers to measures taken.     

Salinity, organic content, micronutrients and heavy metals in pig slurries from South-eastern Spain

The increase in commercial pig production is an opportunity to reuse animal manures in arid and semiarid soils as a source of nutrients and organic matter. However, there are components in pig slurry that are potentially dangerous for the environment. In this study, pig slurries of 36 pig farms in South-eastern Spain were evaluated for salt content (electrical conductivity, chloride and sodium), organic load (BOD5 and COD), micronutrients (Fe, Cu, Mn and Zn), and heavy metals (Cd, Co, Cr, Ni and Pb). Except for electrical conductivity, Cu and Zn, components in pig slurries did not vary considerably between animal production stages, indicating similar management of diverse animal types. Assuming an application rate based on the maximum input of nitrogen from animal manure (210 kg total N/ha/yr), the estimates for soil annual load of Cl and Na, 415 kg/ha, could be a significant salinisation risk. Cu and Zn seemed to be the metals that could be accumulated most in soils where application of pig slurries is common (4 and 15 kg/ha/yr, respectively). The estimated heavy metal (Cd, Co, Cr, Ni and Pb) input to soils would be 260 g/ha/yr, with a relative contribution of Cr>Ni>Pb>Co>Cd.     

Chemical properties of heavy metals in typical hospital waste incinerator ashes in China

Incineration has become the main mechanism for hospital waste (HW) disposal in China after the outbreak of Severe Acute Respiratory Syndrome (SARS) in 2003. However, little information is available on the chemical properties of the resulting ashes. In the present study, 22HW ash samples, including 14 samples of bottom ash and eight samples of fly ash, were collected from four typical HW incineration plants located across China. Chemical analysis indicated that the HW ashes contained large amounts of metal salts of Al, Ca, Fe, K, Mg, Na with a concentration range of 1.8-315gkg(-1). Furthermore, the ashes contained high concentrations of heavy metals such as Ag, As, Ba, Bi, Cd, Cr, Cu, Mn, Ni, Pb, Ti, Sb, Sn, Sr, Zn with a vast range of 1.1-121,411mgkg(-1), with higher concentrations found in the fly ash samples. Sequential extraction results showed that Ba, Cr, Ni and Sn are present in the residual fraction, while Cd existed in the exchangeable and carbonate fractions. As, Mn, Zn existed in the Fe-Mn oxide fraction, Pb was present in the Fe-Mn oxide and residual fractions, and Cu was present in the organic matter fraction. Furthermore, toxicity characteristic leaching procedure (TCLP) results indicated that leached amounts of Cd, Cu and Pb from almost all fly ash samples exceeded the USEPA regulated levels. A comparison between the HW ashes and municipal solid waste (MSW) ash showed that both HW bottom ash and fly ash contained higher concentrations of Ag, As, Bi, Cd, Cr, Cu, Pb, Ti, and Zn. This research provides critical information for appropriate HW incineration ash management plans.     

Metals in Sediments from the Stockholm Region: Geographical Pollution Patterns and Time Trends

The city of Stockholm is intersected and surrounded by water.Freshwater flows eastward and mixes with slightly brackish water in central Stockholm to finally reach the Baltic Sea. Inorder to estimate the magnitude and geographical impact of Stockholm as a source of metals to the aquatic environments, sediments from 117 stations in the Stockholm region have beenanalysed for metals (As, Cd, Co, Cr, Cu, Hg, Ni, Pb and Zn).This paper reports on the geographical pollution pattern and onthe time trends in metal pollution in Stockholm during the 20th century. Stockholm is a strong source of Cd, Cu, Hg,Pb and Zn whereas the Cr concentrations are moderately perturbed.In contrast, the concentrations of As, Co, and Ni are in generalclose to preindustrial levels. The concentrations of Cd, Cu, Hg,Pb and Zn are highest in central Stockholm and eastwards (i.e., in the water flow direction). Sediments upstream of Stockholm andin lakes that are not hydrologically connected to central Stockholm show a significantly lower impact. This may be indicative of metals emitted in Stockholm mainly being transported by the water route. Of Cd, Hg, Pb, and Zn, Cd showsthe most pronounced decline in accumulation rates over the lasttwo decades.     

Century Perspective of Heavy Metal Use in Urban Areas. A Case Study in Stockholm

The inflow and stock (amount in use) of heavy metals (cadmium(Cd), chromium (Cr), copper (Cu), lead (Pb), mercury (Hg), nickel (Ni) and zinc (Zn)) in goods in 1995 have been quantifiedin the anthroposphere of Stockholm, Sweden. Statistics on national, regional and local level were used. Contacts were established with representatives from production and constructionin the industrial sector and with authorities. The results show that the stock of Cd is 0,2 kg per capita. For the other heavymetals the corresponding result per capita is: Cr 8, Cu 170, Hg 0,01, Ni 4, Pb 73 and Zn 40 kg. The inflow varies between2–8%of the stock indicating the importance of the stock. The lowestlevels are for Cu and Pb. Heavy metal levels in solid waste are high, between 15–45% of the amount in the inflow (Hg excluded), the lowest values were for Cu and Pb. Thus, recyclingis incomplete. Long life expectancy goods form the majority of the stock but there is a tendency that short life expectancy goods increase their importance in the inflow. Concealedgoods are also more frequent in inflow than in the stock.     

Heavy metal mobility and potential availability in animal manure: using a sequential extraction procedure

In this study, dairy cow manure, goat manure, and chicken manure were collected from three farms and analyzed to find out the concentration of Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn. The concentration and potential of mobility and availability of heavy metals were studied in the animal manure samples. BCR Sequential extraction procedure was used to determine the binding forms of the metals. In this study, pseudo total concentrations of Mn and Zn were found out to be predominant in all the types of animal manure samples. According to the results, it was traced that Cr, Cu, and Ni were observed to be at the second highest level while Cd, Co, and Pb were seen at the lowest level in all the manure samples. When extractable amounts of heavy metals are taken into consideration, it is seen that the amount of the mobile fractions of heavy metals except for Cr and Ni are higher in comparison with that of immobile fraction in all the animal manure samples. It was also viewed that Mn, Cd, and Zn are more available in dairy cow manure and chicken manure whereas Cd, Co, and Mn are more available in goat manure.     

Fixation and partitioning of heavy metals in slag after incineration of sewage sludge

Fixation of heavy metals in the slag produced during incineration of sewage sludge will reduce emission of the metals to the atmosphere and make the incineration process more environmentally friendly. The effects of incineration conditions (incineration temperature 500-1100°C, furnace residence time 0-60min, mass fraction of water in the sludge 0-75%) on the fixation rates and species partitioning of Cd, Pb, Cr, Cu, Zn, Mn and Ni in slag were investigated. When the incineration temperature was increased from 500 to 1100°C, the fixation rate of Cd decreased from 87% to 49%, while the fixation rates of Cu and Mn were stable. The maximum fixation rates for Pb and Zn and for Ni and Cr were reached at 900 and 1100°C, respectively. The fixation rates of Cu, Ni, Cd, Cr and Zn decreased as the residence time increased. With a 20min residence time, the fixation rates of Pb and Mn were low. The maximum fixation rates of Ni, Mn, Zn, Cu and Cr were achieved when the mass fraction of water in the sludge was 55%. The fixation rate of Cd decreased as the water mass fraction increased, while the fixation rate of Pb increased. Partitioning analysis of the metals contained in the slag showed that increasing the incineration temperature and residence time promoted complete oxidation of the metals. This reduced the non-residual fractions of the metals, which would lower the bioavailability of the metals. The mass fraction of water in the sludge had little effect on the partitioning of the metals. Correlation analysis indicated that the fixation rates of heavy metals in the sludge and the forms of heavy metals in the incinerator slag could be controlled by optimization of the incineration conditions. These results show how the bioavailability of the metals can be reduced for environmentally friendly disposal of the incinerator slag.     

添加CaO对燃煤重金属元素富集效果的影响

选取CaO作为吸附剂,探究了不同燃烧温度下添加CaO对重金属元素在燃煤灰渣中富集效果的影响规律。实验结果表明:添加CaO对重金属元素Cr未起到富集作用,而对Mn,Ni,Cu,Zn,As,Cd,Pb 7种重金属元素的富集效果显著;随燃烧温度的升高,CaO对各赋存形态的Mn,Ni,Cu,Zn,As的富集效果先变好而后变差,对各赋存形态的Cd和Pb的富集效果越来越好;CaO添加比(预处理后的CaO颗粒与预处理后的原煤的质量比)越大,CaO对Mn,Ni,Cu,Zn,As,Cd,Pb的富集效果越好,燃烧温度为850℃时的最佳CaO添加比为4%。     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

赤泥中重金属元素的浸出性与结合形态

采用等离子体质谱仪分析了拜耳法赤泥(BRM)和烧结法赤泥(SRM)中Cr,Ni,Cu,Zn,As,Cd,Cs,Pb等8种重金属元素的含量。采用逐级提取的方法分析了BRM和SRM中8种重金属元素的浸出情况和形态分布差异。实验结果表明:SRM中水溶态As的质量浓度达到17.3μg/L,BRM和SRM中可交换态Cr的质量浓度均在2 300μg/L以上,对水环境可能存在潜在危害;两种赤泥中不同形态重金属的浸出率有较大差异,SRM中Ni和BRM中Zn的总浸出率分别在60%和50%以上。     

Effect of sintering temperature on the properties and leaching of incinerator bottom ash.

The fine particle size fraction of municipal solid waste incinerator bottom ash is often problematic because reuse applications for this material are limited. In these experiments incinerator bottom ash with a particle size of less than 8 mm was processed using conventional ceramic production techniques involving wet milling, drying, compacting and sintering. The effect of sintering temperature on the sintered density, microstructure, acid neutralization capacity (ANC) and the release of metal ions as a function of leachate pH are reported. Sintering at 1080 degrees C produced samples with maximum density. This material contained diopside (CaMgSi2O6), clinoenstatite (Mg2Si2O6) and wollastonite (CaSiO3) as the major crystalline phases. The acid neutralization capacity of sintered samples is significantly lower than milled bottom ash, and further reduces as the sintering temperature increases. This is associated with reduced leaching of Ca from sintered ash samples under all leachate pH conditions. Heavy metals present in the incinerator bottom ash included Cr, Cu, Ni, Zn, Cd and Pb. Sintering under optimum conditions reduced the leachable fraction of these metals under aggressive acid conditions (leachate pH 3) by factors ranging from 90% for Ni to greater than 99% for Cr, Cd, Zn and Pb.     

Assessment of benefits and risks of landfill materials for agriculture in Eritrea

In Eritrea, farmers have applied landfill materials as fertiliser to their fields for several decades. A sampling scheme in the landfill site of Asmara and selected farmers' fields was carried out to investigate the benefits and risks of using landfill materials for agriculture. Soil samples were collected from farmers' fields (7 samples) and from the Asmara landfill site (12 samples). The samples were analysed for major plant nutrients, heavy metals (Cd, Cr, Cu, Pb, Ni, Hg and Zn), and some physical properties. Nearly 65% (by weight) of the total landfill material mined from the landfill site constituted waste fractions of various substances. The remaining 35% was composed of soil-like materials, which are apparently used to fertilize agricultural soils. The average organic matter, total nitrogen, and available phosphorus contents of soils with landfill material measured 2.4%, 0.13%, and 45 mg kg(-1), respectively. However, soils without landfill material consisted of 1.1 % organic matter, 0.04% total N, and <40 mg kg(-1) of available P. Except for Hg, all the other heavy metals in the landfill site showed values above the permissible limits. In particular, the average concentrations of Cu (913 mg kg(-1)) and Pb (598 mg kg(-1)) in the landfill site were nine-fold and four-fold greater than the allowable limits, respectively. It is, therefore, suggested that composting fresh organic wastes should be considered and tested as an alternative material for fertilising agricultural soils and to maintain the quality of the environment.     

Land application of biosolids. Soil response to different stabilization degree of the treated organic matter

The effect of land application of biosolids on an agricultural soil was studied in a 2-month incubation experiment. The soil microbial biomass and the availability of heavy metals in the soil was monitored after the application of four different composting mixtures of sewage sludge and cotton waste, at different stages of composting. Land application caused an increase of both size and activity of soil microbial biomass that was related to the stabilization degree of the composting mixture. Sewage sludge stabilization through composting reduced the perturbance of the soil microbial biomass. At the end of the experiment, the size and the activity of the soil microbial biomass following the addition of untreated sewage sludge were twice those developed with mature compost. For the mature compost, the soil microbial biomass recovered its original equilibrium status (defined as the specific respiration activity, qCO2) after 18 days of incubation, whereas the soil amended with less stabilized materials did not recover equilibrium even after the two-month incubation period. The stabilization degree of the added materials did not affect the availability of Zn, Ni, Pb, Cu, Cr and Cd in the soil in the low heavy metal content of the sewage sludge studied. Stabilization of organic wastes before soil application is advisable for the lower perturbation of soil equilibria status and the more efficient C mineralization.