Heavy metal mobility and potential availability in animal manure: using a sequential extraction procedure

In this study, dairy cow manure, goat manure, and chicken manure were collected from three farms and analyzed to find out the concentration of Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn. The concentration and potential of mobility and availability of heavy metals were studied in the animal manure samples. BCR Sequential extraction procedure was used to determine the binding forms of the metals. In this study, pseudo total concentrations of Mn and Zn were found out to be predominant in all the types of animal manure samples. According to the results, it was traced that Cr, Cu, and Ni were observed to be at the second highest level while Cd, Co, and Pb were seen at the lowest level in all the manure samples. When extractable amounts of heavy metals are taken into consideration, it is seen that the amount of the mobile fractions of heavy metals except for Cr and Ni are higher in comparison with that of immobile fraction in all the animal manure samples. It was also viewed that Mn, Cd, and Zn are more available in dairy cow manure and chicken manure whereas Cd, Co, and Mn are more available in goat manure.     

Chemical properties of heavy metals in typical hospital waste incinerator ashes in China

Incineration has become the main mechanism for hospital waste (HW) disposal in China after the outbreak of Severe Acute Respiratory Syndrome (SARS) in 2003. However, little information is available on the chemical properties of the resulting ashes. In the present study, 22HW ash samples, including 14 samples of bottom ash and eight samples of fly ash, were collected from four typical HW incineration plants located across China. Chemical analysis indicated that the HW ashes contained large amounts of metal salts of Al, Ca, Fe, K, Mg, Na with a concentration range of 1.8-315gkg(-1). Furthermore, the ashes contained high concentrations of heavy metals such as Ag, As, Ba, Bi, Cd, Cr, Cu, Mn, Ni, Pb, Ti, Sb, Sn, Sr, Zn with a vast range of 1.1-121,411mgkg(-1), with higher concentrations found in the fly ash samples. Sequential extraction results showed that Ba, Cr, Ni and Sn are present in the residual fraction, while Cd existed in the exchangeable and carbonate fractions. As, Mn, Zn existed in the Fe-Mn oxide fraction, Pb was present in the Fe-Mn oxide and residual fractions, and Cu was present in the organic matter fraction. Furthermore, toxicity characteristic leaching procedure (TCLP) results indicated that leached amounts of Cd, Cu and Pb from almost all fly ash samples exceeded the USEPA regulated levels. A comparison between the HW ashes and municipal solid waste (MSW) ash showed that both HW bottom ash and fly ash contained higher concentrations of Ag, As, Bi, Cd, Cr, Cu, Pb, Ti, and Zn. This research provides critical information for appropriate HW incineration ash management plans.     

Fixation and partitioning of heavy metals in slag after incineration of sewage sludge

Fixation of heavy metals in the slag produced during incineration of sewage sludge will reduce emission of the metals to the atmosphere and make the incineration process more environmentally friendly. The effects of incineration conditions (incineration temperature 500-1100°C, furnace residence time 0-60min, mass fraction of water in the sludge 0-75%) on the fixation rates and species partitioning of Cd, Pb, Cr, Cu, Zn, Mn and Ni in slag were investigated. When the incineration temperature was increased from 500 to 1100°C, the fixation rate of Cd decreased from 87% to 49%, while the fixation rates of Cu and Mn were stable. The maximum fixation rates for Pb and Zn and for Ni and Cr were reached at 900 and 1100°C, respectively. The fixation rates of Cu, Ni, Cd, Cr and Zn decreased as the residence time increased. With a 20min residence time, the fixation rates of Pb and Mn were low. The maximum fixation rates of Ni, Mn, Zn, Cu and Cr were achieved when the mass fraction of water in the sludge was 55%. The fixation rate of Cd decreased as the water mass fraction increased, while the fixation rate of Pb increased. Partitioning analysis of the metals contained in the slag showed that increasing the incineration temperature and residence time promoted complete oxidation of the metals. This reduced the non-residual fractions of the metals, which would lower the bioavailability of the metals. The mass fraction of water in the sludge had little effect on the partitioning of the metals. Correlation analysis indicated that the fixation rates of heavy metals in the sludge and the forms of heavy metals in the incinerator slag could be controlled by optimization of the incineration conditions. These results show how the bioavailability of the metals can be reduced for environmentally friendly disposal of the incinerator slag.     

Effect of nine years of animal waste deposition on profile distribution of heavy metals in Abeokuta,south-western Nigeria and its implication for environmental quality

Uncontrolled deposition of waste from animal farms is a common practice in south-western Nigeria, and the presence of heavy metals in soil constitutes environmental and health hazards by polluting the soil, ground water, adjoining streams and rivers. The study investigated the profile distribution of Mn, Pb, Cd, Zn, Fe, Cu, Ni and Cr in some tropical Alfisols in south-western Nigeria after nine years disposal of animal wastes. The amount of these metals in the soil horizons was high enough to cause health and phytotoxic risks. All the metals except Zn and Cr increased down the profile, while Mn, Pb, Cd, Fe, Cu and Ni accumulated at 80–120 cm depth. The increment of these metals at this depth over the top soil were 26%, 143%, 72%, 47%, 328% for Mn, Pb, Cd, Cu and Ni, respectively. It thus, shows their mobility and the possibility of polluting ground water. The Mn content at the poultry and cattle waste sites increased by 127% and 25%, respectively over the control, while that of cattle and swine dump site for Cd content were 9.82 and 15.63 mg kg^?1, respectively. Lead content also increased by 8.52 and 5.25 mg kg^?1, respectively.There was the accumulation of Zn and Cu at the swine dump site while the cattle dump site had the highest amounts of nickel and chromium. The least amount of Fe was recorded at the swine waste dump site. The reduction in organic matter with depths together with the reduced pH might have favored the mobility of the metals. The ranking of pollution among the sites was poultry > swine > cattle > sheep and could be due to the type of ration fed, the vaccination programmes, sanitation programmes and other management practices.     

Investigation of potentially toxic heavy metals in different organic wastes used to fertilize market garden crops

The benefits of using organic waste as fertilizer and soil amendment should be assessed together with the environmental impacts due to the possible presence of heavy metals (HMs). This study involved analysing major element and HM contents in raw and size-fractionated organic wastes (17 sewage sludges and composts) from developed and developing countries. The overall HM concentration pattern showed an asymmetric distribution due to the presence of some wastes with extremely high concentrations. HM concentrations were correlated with the size of cities or farms where the wastes had been produced, and HM were differentiated with respect to their origins (geogenic: Cr–Ni; anthropogenic agricultural and urban: Cu–Zn; anthropogenic urban: Cd–Pb). Size fractionation highlighted Cd, Cu, Zn and Pb accumulation in fine size fractions, while Cr and Ni were accumulated in the coarsest. HM associations with major elements revealed inorganic (Al, Fe, etc.) bearing phases for Cr and Ni, and sulfur or phosphorus species for Cd, Cu Pb and Zn.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

硫酸锰渣污染土壤中重金属的形态分布及生物活性

测定了硫酸锰渣污染土壤中Cu,Zn,Cd,Pb,Mn的总量和各形态含量.结果表明重金属总量远超过环境背景值和土壤环境二级标准.重金属各形态分布特征:Cu,有机态>残渣态>铁锰氧化态>碳酸盐态>可交换态;Zn,残渣态>铁锰氧化态>有机态>碳酸盐态>可交换态;Cd,铁锰氧化态>可交换态>碳酸盐态>残渣态>有机态;Pb,铁锰氧化态>残渣态>有机态>碳酸盐态>可交换态;Mn,铁锰氧化态>残渣态>可交换态>有机态>碳酸盐态.重金属的生物可利用性系数和迁移系数均为Cd>Mn>Pb>Cu>Zn.     

无机稳定剂处理重金属污染土壤

以重金属污染土壤为研究对象，比较了铁屑、蒙脱石、碳酸钙和羟基磷灰石4种稳定剂对土壤中Pb，Zn，Cd，Cu 4种重金属的稳定效果。实验结果表明，4种稳定剂稳定效率的大小顺序为：羟基磷灰石﹥碳酸钙﹥蒙脱石﹥铁屑。当稳定剂质量分数为10%时，羟基磷灰石、碳酸钙、蒙脱石和铁屑对Pb，Zn，Cd，Cu 4种重金属的平均稳定效率分别为99.63%，98.53%，97.15%，86.95 %。未加稳定剂时，土壤中的Pb以残渣态为主，Zn以残渣态和可交换态为主，Cd以残渣态为主，Cu以残渣态和可交换态为主；加入稳定剂后，土壤中4种金属可交换态的所占比例（简称占比）均显著降低，还原态的占比明显增大，残渣态的占比略有增大，氧化态的占比基本保持不变。     

Variations of metal distribution in sewage sludge composting

In the study, the variations of heavy metal distributions (of Cu, Mn, Pb, and Zn) during the sewage sludge composting process were investigated by sequential extraction procedures. The total content of Cu and Zn in the composted mixture increased after the composting process. Mn and Zn were mainly found in mobile fractions (exchangeable fraction (F1), carbonate fraction (F2), and Fe/Mn oxide fraction (F3)). Cu and Pb were strongly associated with the stable fractions (organic matter/sulfides fraction (F4) and residual fraction (F5)). These five metal fractions were used to calculate the metal mobility (bioavailability) in the sewage sludge and composted mixture. The mobility (bioavailability) of Mn, Pb, and Zn (but not Cu) increased during the composting process. The metal mobility in the composted mixture ranked in the following order: Mn>Zn>Pb>Cu.     

气化炉渣的重金属浸出特性及化学形态分析

分别采用硫酸硝酸法、水平振荡法和醋酸缓冲溶液法制取气化炉渣的浸出液，考察了不同提取方式对浸出液中重金属质量浓度的影响。采用改进BCR连续提取法对气化炉渣中的重金属Cr，Zn，Cu，Pb，Ni，As，Cd的化学形态进行了分析。实验结果表明：煤气化工艺中的气化炉渣属第Ⅰ类一般工业固体废物;在3种提取方式中，醋酸缓冲溶液法的重金属浸出种类最多，且浸出量最大;Cd和Cr对环境具有较高的潜在危害性，Cu次之，Zn，Pb，Ni，As主要以残渣态形式存在，对环境的直接危害性较低。     

添加CaO对燃煤重金属元素富集效果的影响

选取CaO作为吸附剂,探究了不同燃烧温度下添加CaO对重金属元素在燃煤灰渣中富集效果的影响规律。实验结果表明:添加CaO对重金属元素Cr未起到富集作用,而对Mn,Ni,Cu,Zn,As,Cd,Pb 7种重金属元素的富集效果显著;随燃烧温度的升高,CaO对各赋存形态的Mn,Ni,Cu,Zn,As的富集效果先变好而后变差,对各赋存形态的Cd和Pb的富集效果越来越好;CaO添加比(预处理后的CaO颗粒与预处理后的原煤的质量比)越大,CaO对Mn,Ni,Cu,Zn,As,Cd,Pb的富集效果越好,燃烧温度为850℃时的最佳CaO添加比为4%。     

万山汞矿区土壤重金属污染特征及来源解析

以万山汞矿区土壤为研究对象,采用电感耦合等离子体质谱仪和原子荧光光谱仪测定土壤中的重金属含量,分别运用内梅罗综合污染指数（NPI）法和潜在生态风险指数（RI）法评价土壤重金属污染和潜在生态风险,并应用相关性分析、主成分分析和聚类分析对土壤重金属来源进行分析。结果表明：土壤Hg、Cd、As、Pb、Cu、Ni和Zn出现不同程度累积,分别达贵州省背景值的263.61、2.31、1.28、2.11、1.70、1.01和3.52倍;土壤重金属平均NPI为188.00,属于严重污染水平,Hg是主要污染因子;土壤重金属平均RI为10 655.70,属于极强潜在生态风险水平,Hg是主要潜在生态风险因子;土壤中Cu、Ni、Cr主要源于自然活动,As、Pb、Zn主要源于燃煤和交通运输污染,Cd主要源于农业污染,Hg主要源于汞冶炼污染。     

Salinity, organic content, micronutrients and heavy metals in pig slurries from South-eastern Spain

The increase in commercial pig production is an opportunity to reuse animal manures in arid and semiarid soils as a source of nutrients and organic matter. However, there are components in pig slurry that are potentially dangerous for the environment. In this study, pig slurries of 36 pig farms in South-eastern Spain were evaluated for salt content (electrical conductivity, chloride and sodium), organic load (BOD5 and COD), micronutrients (Fe, Cu, Mn and Zn), and heavy metals (Cd, Co, Cr, Ni and Pb). Except for electrical conductivity, Cu and Zn, components in pig slurries did not vary considerably between animal production stages, indicating similar management of diverse animal types. Assuming an application rate based on the maximum input of nitrogen from animal manure (210 kg total N/ha/yr), the estimates for soil annual load of Cl and Na, 415 kg/ha, could be a significant salinisation risk. Cu and Zn seemed to be the metals that could be accumulated most in soils where application of pig slurries is common (4 and 15 kg/ha/yr, respectively). The estimated heavy metal (Cd, Co, Cr, Ni and Pb) input to soils would be 260 g/ha/yr, with a relative contribution of Cr>Ni>Pb>Co>Cd.     

Use of dewatered municipal sludge on Canna growth in pot experiments with a barren clay soil

The present study evaluated the possibility of using the dewatered municipal sludge for non-agricultural purposes. The sludge was amended with soil and was applied at 0, 165, 330, 495 and 660 t/ha to promote the growth of Canna. The results showed that the Canna growth pattern exhibited a pronounced positive growth response in the range of 165–495 t/ha, and the Canna could not survive at an amendment rate of 660 t/ha. The analysis of chlorophyll fluorescence parameters showed that sludge did no harm to Canna, while under the conditions of barren soil alone, the plants were put into nutrients stress conditions. Due to the application of sludge, the concentration of heavy metals (Cu, Zn, Cr, Cd, Pb and Ni) in soil increased. However, by planting of Canna, contents of Cd, Ni and Zn showed trends of decline; Cd and Ni have shown a significant decline in concentration, while Zn had only limit response. As a result, dewatered sludge might be used to amend the barren soil and Canna could be used for phytoremediation of sludge.     

A study of heavy metals and their fate in the composting of tannery sludge

Tannery waste is categorized as toxic and hazardous in Malaysia due to its high content of Cr (in excess of 500 mg/kg) and other heavy metals. Heavy metals, when in high enough concentrations, have the potential to be both phytotoxic and zootoxic. Heavy metals are found as contaminants in tannery sludge. This investigation aimed to identify the fate of chromium, cadmium, copper, lead, and zinc concentrations in tannery sludge throughout a 50-day composting cycle. The results of this study showed a general increase in the removal of Cr, Cd, Pb, and to a much smaller extent Zn and Cu, manifested by a decrease in their overall concentrations within the solid fraction of the final product (the decreases were likely the result of leaching). Furthermore, in using a sequential extraction method for sludge composting at different phases of treatment, a large proportion of the heavy metals were found to be associated to the residual fraction (70-80%) and fractions more resistant to extraction, X-NaOH, X-EDTA, X-HNO3 (12-29%). Less than 2% of the metals were bound to bioavailable fractions X-(KNO3+H2O).     

Evaluation of Active Cap Materials for Metal Retention in Sediments

This study evaluated chemically active amendments used to construct active caps for remediating contaminated sediments. Three experiments assessed the effects of apatite, organoclay, zeolite, and biopolymers (chitosan and xanthan) on metal mobility, retention, and speciation. The first showed that the amendments individually and in mixtures (2 percent dry weight) reduced the concentrations of Cr, Co, Ni, and Pb in water extracts from reduced sediment. The second experiment, which used sequential extraction procedures to evaluate the effects of the amendments on metal speciation, showed that the amendments reduced the potentially mobile fractions of Pb, Zn, Ni, Cr, and Cd that are likely to be bioavailable. Last, column studies showed that active caps composed of the amendments prevented the diffusive transport of metals from contaminated sediment over six months. In addition, there was a “zone of influence” beneath the caps in which water extractable concentrations of metals declined substantially compared with untreated sediment. © 2014 Wiley Periodicals, Inc.     

Concentrations of heavy metals in fly ash from a coal-fired power plant with respect to the new Finnish limit values

In Finland, the new limit values for heavy metals in fertilizers used in agriculture and in forestry came into force in March 2007, and for materials used as earth construction agents, in June 2006. From the utilization point of view, it was notable that the total heavy metal concentrations (Cd, Cu, Pb, Cr, Mo, Zn, As, Ni, Ba, and Hg) in fly ash from a coal-fired power plant were lower than those limit values. The concentrations of the easily soluble elements Ca, Mg, Na, P, and Zn in the fly ash were between 3.5 and 35 times higher than those found in the coarse mineral soils of Finland. Fly ash is a potential agent for soil remediation and for improving soil fertility. If inorganic materials and by-products are utilized in earthworks, the content of harmful compounds must be low and the harmful components must be tightly bound to the matrix. Therefore, a five-stage sequential extraction procedure was used to evaluate the extractability of different elements in fly ash into the following fractions: (1) the water-soluble fraction, (2) the exchangeable fraction (CH₃COOH), (3) the easily reduced fraction (NH₂OH-HCl), (4) the oxidizable fraction (H₂O₂ + CH₃COONH₄), and (5) the residual fraction (HF + HNO₃ + HCl).     

Leaching behavior of heavy metals from municipal solid waste incineration bottom ash and its geochemical modeling

With the increase in the number of municipal solid waste incineration (MSWI) plants constructed in China recently, great attention has been paid to the heavy metal leaching toxicity of MSWI residues. In this study, the effects of various parameters, including extractant, leaching time, liquid-to-solid ratio, leachate pH, and heavy metal content, on the release properties of Cd, Cr, Cu, Ni, Pb, and Zn from MSWI bottom ash were investigated. Partial least-squares analysis was employed to highlight the interrelationships between the factors and response variables. Both experimental research and geochemical modeling using Visual MINTEQ software were conducted to study the pH-dependent leaching behavior of these metals in fresh and weathered bottom ash, considering precipitation/dissolution and surface complexation reactions (adsorption by hydrous ferric oxide and amorphous aluminum oxide/hydroxide). The results showed that leachate pH was the predominant factor influencing heavy metal leachability. The leaching of Cu, Pb, and Zn was mainly controlled by precipitation/dissolution reactions, whereas surface complexation had some effect on the leaching of Cr, Cd, and Ni for certain pH ranges. The modeling results aggreed well with the experimental results. Part of this work was presented at the Fourth International Conference on Combustion, Incineration/Pyrolysis and Emission Control (i-CIPEC)     

Acidic bioleaching of heavy metals from sewage sludge

The overall objective of this study was to evaluate the use of controlled bio-acidification prior to land application as a decontamination process to remove heavy metals from sludge. The sulfur-oxidizing bacteria were naturally available in the sludge samples and were activated by providing sulfur and aeration at 28°C–30°C. Activation resulted in bio-acidification to pH 2 within 5–11 days. Successive inoculation of fresh sludges with 5% acidified samples reduced the acidification time to 2–3 days in most samples. Bio-acidification resulted in dissolving significant quantities of heavy metals from all sludge types tested. The maximum solubilization results were: 86%–97% for Ni; 48%–98% for Pb; 26%–71% for Cr; 18%–91% for Zn; 16%–90% for Cu; 7%–60% for Cd. Limited metal solubilization results were observed in the various control samples that accompanied the bio-acidified samples. The leaching results in the control samples were limited to 2%–19% for Ni, 0%–7% for Pb, 0%–5% for Cr, 0.3%–4% for Zn, 0.2%–4% for Cu and 0%–3% for Cd. The results confirmed that Ni and Pb were the easiest metals to dissolve from the various sludge types. On the other hand, the lowest solubilization results were observed for Cu and Cd, and moderate solubilization results were achieved for Cr. The bio-acidification process resulted in moderate gains in terms of improving the suitability of tested sludges for land application. Received: April 19, 1999 / Accepted: November 4, 1999     

Chemical sequential extraction of heavy metals and sulphur in bottom ash and in fly ash from a pulp and paper mill complex

A five-stage sequential extraction procedure was used to determine the distribution of 11 metals (Cd, Cr, Cu, Mo, Pb, Zn, As, Co, V, Ni, Ba), and sulphur (S) in bottom ash and in fly ash from a fluidized bed co-combustion (i.e. wood and peat) boiler of Stora Enso Oyj Oulu Mill at Oulu, Northern Finland, into the following fractions: (1) water-soluble fraction (H2O); (2) exchangeable fraction (CH3COOH); (3) easily reduced fraction (NH2OH-HCl); (4) oxidizable fraction (H2O2 + CH3COONH4); and (5) residual fraction (HF + HNO3 + HCl). Although metals were extractable in all fractions, the highest concentrations of most of the metals occurred in the residual fraction. From the environmental point of view, this fraction is the non-mobile fraction and is potentially the least harmful. The Ca concentrations of 29.3 g kg(-1) (dry weight) in bottom ash and of 68.5 g kg(-1) (dry weight) in fly ash were correspondingly approximately 18 and 43 times higher than the average value of 1.6 g kg(-1) (dry weight) in arable land in Central Finland. The ashes were strongly alkaline pH (approximately 12) and had a liming effects of 9.3% (bottom ash) and 13% (fly ash) expressed as Ca equivalents (dry weight). The elevated Ca concentrations indicate that the ashes are potential agents for soil remediation and for improving soil fertility. The pH and liming effect values indicate that the ashes also have a pH buffering capacity. From the environmental point of view, it is notable that the heavy metal concentrations in both types of ash were lower than the Finnish criteria for ash utilization.