NH3选择性还原NOx催化剂的制备及性能评价

以堇青石蜂窝陶瓷为载体,采用TiO2浆液涂覆载体,再负载活性组分V和W,制备了NH3选择性还原NOx催化剂,研究了TiO2涂层的制备工艺条件,并对催化剂的活性及稳定性进行了评价.实验结果表明,制备TiO2涂层的最佳工艺条件为:TiO2浆液中铝溶胶质量分数12％,浆液pH 1.91,浆液固含量(TiO2与铝溶胶中Al2O...     

湿法石灰石/石膏烟气脱硫泵的选材及选型

简述了湿法烟气脱硫生产中浆液的性质，并根据浆液特点阐述了耐磨耐蚀泵的选材与选型．为湿法石灰石／石膏烟气脱硫浆液输送泵的研发提供参考。     

“水泥—黏土—粉煤灰—生石灰”固化浆液性能试验

松散岩体固化已成为一种提高岩体强度，改善巷道支护条件的重要手段，已应用的固化注浆材料各有特点，如单一水泥浆液的优点是结石体强度高、透水性低，材料来源广、价廉，但其可注性及稳定性较差，凝结时间长，而且凝结时间难以控制等，限制了它的适用范围，而在水泥浆中加入添加剂，则可以改善水泥浆的性能，水泥一粉煤灰浆液可以提高水泥浆的可注性，提高浆液固结的早期强度，增强浆液的稳定性，减少水泥消耗，降低成本。     

600MW机组湿法脱硫吸收塔溢流原因分析及对策

阐述了火电厂600MW机组石灰石—石膏湿法脱硫系统吸收塔浆液溢流的危害,分析了吸收塔浆液溢流的原因,主要是石膏浆液品质差、氧化风量不合理、浆液循环泵、浆液喷淋的影响,溢流管接口位置布置不合理等。通过适当降低运行液位、合理布置吸收塔溢流管道等措施解决了吸收塔浆液溢流问题,确保脱硫系统稳定运行。     

石灰石-石膏法烟气脱硫系统处理废稀硫酸

采用石灰石-石膏法脱硫装置处理废稀硫酸.研究了石灰石浆液和废稀硫酸的不同投加顺序以及不同反应晶种(石膏浆液、石膏稀浆液)对所得石膏晶粒形态和抽滤物含水率的影响.试验结果表明:与废稀硫酸加入石灰石浆液的方式相比,石灰石浆液加入废稀硫酸的方式更利于石膏结晶,晶粒更大,所得石膏抽滤物含水率更低;以石膏浆液和石膏稀浆液作为反应...     

湿法脱硫多因素引起的浆液恶化原因分析及处理措施

在石灰石—石膏湿法脱硫系统中,吸收塔浆液恶化是系统运行经常出现的问题,浆液恶化不仅易影响浆液pH值,降低系统的脱硫效率,还会造成脱硫副产物石膏脱水困难。为此,结合2×600 MW机组湿法脱硫系统浆液恶化问题,通过检测与分析探讨了引起浆液品质变差的原因,并提出了解决措施。     

石灰石/石膏湿法烟气脱硫金属浆液循环泵国产化研究及实践

介绍了襄樊五二五泵业有限公司成功开发烟气脱硫金属浆液循环泵的相关成果，包括泵的水力模型、结构、机械密封、材料的研究等。经工业性考核和鉴定，该泵已完全可以实现我国50～600MW火电机组湿法脱硫装置的各种金属浆液循环泵的国产化。     

浆液循环泵运行电流影响因素分析研究

着重分析了吸收塔浆液液位、浆液密度两个运行参数对循环泵运行电流的影响。结果认为：浆液液位对泵电流影响较小,实际运行中可不予考虑;浆液密度对泵运行电流影响较大,需要加强优化控制。     

石灰石／石灰-石膏湿法脱硫浆液溢流问题研究

在火电厂石灰石／石灰一石膏湿法脱硫系统中,吸收塔浆液溢流是运行过程中常见的问题之一,它对FGD系统的稳定运行非常不利。分析了吸收塔浆液溢流的成因,介绍了浆液溢流对FGD系统运行的危害,提出了吸收塔浆液溢流的预防和处理措施。     

吸收塔浆液起泡原因分析及消泡剂的选择

针对在多个湿法脱硫项目中出现的吸收塔浆液起泡现象,分析了引起塔内浆液起泡的原因,提出了相应的处理措施,探讨脱硫吸收塔浆液起泡专用消泡剂的作用原理及选择原则。     

Recovery of silicon powder from kerf loss slurry waste using superconducting high gradient magnetic separation technology

A major challenge in recycling of silicon powder from kerf loss slurry waste is the complete removal of metal particles. The traditional acid leaching method is costly and not green. In this paper, a novel approach to recover high-purity Si from the kerf loss slurry waste of solar grade silicon was investigated. The metal impurities were removed with superconducting high gradient magnetic separation technology. The effects of process parameters such as magnetic flux density, slurry density, and slurry flow velocity on the removal efficiency were investigated, and the parameters were optimized. In one lot of control experiments, the silicon content was increased from 90.91 to 95.83%, iron content reduced from 3.24 to 0.57%, and aluminum content from 2.44 to 1.51% under the optimum conditions of magnetic flux density of 4.0 T, slurry density of 20 g/L, and slurry flow velocity of 500 mL/min. The result indicates that the superconducting high gradient magnetic separation technology is a feasible purifying method, and the magnetic separation concentrate could be used as an intermediate product for high-purity Si powder.

     

多炉一塔湿法脱硫系统石膏脱水环节探讨

通过对脱硫吸收塔内五个区浆液的综合分析,讨论了石膏脱水系统环节的设计,结合天津第一热电厂脱硫工程,分析了各脱水设备在不同工艺流程中的选择条件,提出了一种湿法脱硫过程中浆液分配器的改进设计。     

Air stripping of ammonia from pig slurry: characterisation and feasibility as a pre- or post-treatment to mesophilic anaerobic digestion

The objective of the present paper has been to study the effect of pig slurry waste type, fresh or anaerobically digested, and the effect of initial pH on ammonia air stripping from pig slurry waste at high temperature (80 degrees C). Stripping process as pre- or post-treatment to anaerobic digestion has been also evaluated. Treatment performances differ according to pig slurry type. When fresh pig slurry is used, despite working at 80 degrees C, a high initial pH (11.5) is required for complete ammonia removal. On the other hand, for digested pig slurry, complete ammonia removal without pH modification is possible and organic matter significantly less contaminates recovered ammonia salt. Batch anaerobic tests showed that ammonia air stripping is not an advisable pre-treatment to pig slurry anaerobic digestion.     

Chemical and spectroscopic characterization of organic matter during the anaerobic digestion and successive composting of pig slurry

In this work, anaerobic digestion of pig slurry and successive composting of the digestate after centrifugation were studied by means of chemical analysis, FTIR and fluorescence spectroscopy as excitation–emission matrix (EEM). Chemical analysis highlighted the organic matter transformation occurring during the processes. A decrease of volatile solids and total organic carbon were observed in the digestate with respect to the fresh pig slurry as a consequence of the consumption of sugars, proteins, amino acids and fatty acids used by microorganisms as a C source. Water Extractable Organic Matter (WEOM) was obtained for all samples and fractionated into a hydrophilic and a hydrophobic fraction. The highest WEOM value was found in the pig slurry indicating a high content of labile organic C. The digestate centrifuged and the digestate composted showed lower hydrophilic and higher hydrophobic contents because of the decrease of labile C. Total phenolic content was lower in the digestate with respect to fresh pig slurry sample (36.7%) as a consequence of phenolic compounds degradation. The strong decrease of total reducing sugars in the digestate (76.6%) as compared to pig slurry confirmed that anaerobic process proceed mainly through consumption of sugars which represent a readily available energy source for microbial activity. FTIR spectra of pig slurry showed bands indicative of proteins and carbohydrates. A drop of aliphatic structures and a decrease of polysaccharides was observed after the anaerobic process along with the increase of the peak in the aromatic region. The composted substrate showed an increase of aromatic and a relative decrease of polysaccharides. EEM spectra provided tryptophan:fulvic-like fluorescence ratios which increased from fresh substrate to digestate because of the OM decompostion. Composted substrate presented the lowest ratio due to the humification process.     

A study of iron mineral transformation to reduce red mud tailings

This study examines the effects of iron mineral transformation in an aluminum extraction process on the settling behavior, and the physical and chemical properties of the resulting red mud slurry that must be disposed of. By producing a red mud with a higher solid content, the total volume of mud slurry will also be reduced for a given alumina production rate and more caustic soda will be recovered. The settling behavior and the mineralogical, physical, and physico-chemical properties of one bauxite and three red muds processed under varying conditions were analyzed based on examination of the iron mineral transformations. The properties of red muds derived from the same bauxite can differ markedly due to variations in operating conditions of the Bayer process, such as temperature and the addition of a reducing agent. The settling of red mud can be improved by converting goethite into hematite and/or magnetite to produce a mud of larger particle size, smaller specific surface area, and larger specific gravity, characteristics which reduce the total volume of mud slurry to be disposed of and which allow for less potential contamination from caustic soda. This study also found that the by-product--Bayer sodalite--has the high exchange capacity for Na+ that might contribute to the long-term environmental problems.     

Effects of fly ash addition on physical properties of porous clay-fly ash composites via polymeric replica technique

The porous composites of clay and fly ash have the potential to be used in many fields, such as catalyst support and gas adsorbents. In this study, various ratios of fly ash (1–2) with different percentage of suspension (50–70 wt%) were applied to produce porous clay-fly ash composites via polymeric replica technique. Fabrication process starts by mixing clay and fly ash in distilled water to form slurry. The process is followed by fully immersing polymer sponge in slurry. The excess slurry is then removed through squeezing. Finally, the sponge coated with slurry is sintered at 500 and 1250 °C for 1 h. It is found that the compressive strength of porous composites improves significantly (0.178–1.28 MPa) when the amount of clay-fly ash suspension mixture (50–70 wt%) increases. The compressive strength of porous composites is mainly attributed to the mullite, quartz and amorphous phase formations. These results are supported by X-ray diffraction analysis. On the other hand, increase in the amount of suspension reduces the apparent density (from 2.44 to 2.32 g/cm³) and porosity (from 97 to 85 %). The reduction in apparent density is believed to be caused by the presence of high fly ash content in porous composites. The melted fly ash cenospheres have closed the internal pores and increased density of samples. Higher suspension level not only reduces porosity, but also increases close pores of the porous composites. The results are justified through the observation from the structures of porous clay-fly ash composites.     

利用造纸黑液制备水煤浆添加剂

利用造纸黑液中有效成分，经过适当处理制备水煤浆添加剂，并且对添加剂的性能进行了测试。结果表明，依照该工艺生产的添加剂，性能优良，能够满足工业生产需要。     

Enhanced methane production from ultrasound pre-treated and hygienized dairy cattle slurry

The effect of hygienization (70 °C, 60 min) and ultrasound (6000 ± 500 kJ/kg total solids (TS)) pre-treatments on hydrolysis and biological methane (CH(4)) potential (BMP) of dairy cattle slurry was studied. The BMP of the untreated slurry (control) was 210 ± 10 Nm(3) CH(4)/ton volatile solids (VS) added; after ultrasound pre-treatment it was 250 ± 10 Nm(3) CH(4)/ton VS(added) and after hygienization 280 ± 20 Nm(3) CH(4)/ton VS(added). The specific methanogenic activity (SMA) of the inoculum increased from 22 (untreated) to 26 (ultrasound treated) and up to 28 N ml CH(4)/g VS d, after hygienization. However, only hygienization achieved a positive net energy balance. Both pre-treatments increased the VS-based hydrolysis of slurry (10-96%), soluble nitrogen (N(sol)) content in digestates (20 ± 5%) and biodegradability of the slurry (8 ± 3%) as estimated via elevated VS removal.