Investigation of a Mercury Speciation Technique for Flue Gas Desulfurization Materials

Abstract

Most of the synthetic gypsum generated from wet flue gas desulfurization (FGD) scrubbers is currently being used for wallboard production. Because oxidized mercury is readily captured by the wet FGD scrubber, and coal-fired power plants equipped with wet scrubbers desire to benefit from the partial mercury control that these systems provide, some mercury is likely to be bound in with the FGD gypsum and wallboard. In this study, the feasibility of identifying mercury species in the FGD gypsum and wallboard samples was investigated using a large sample size thermal desorption method. Potential candidates of pure mercury standards including mercuric chloride (HgCl₂), mercurous chloride (Hg₂Cl₂), mercury oxide (HgO), mercury sulfide (HgS), and mercuric sulfate (HgSO₄) were analyzed to compare their results with those obtained from FGD gypsum and dry wallboard samples. Although any of the thermal evolutionary curves obtained from these pure mercury standards did not exactly match with those of the FGD gypsum and wallboard samples, it was identified that Hg₂Cl₂ and HgCl₂ could be candidates. An additional chlorine analysis from the gypsum and wallboard samples indicated that the chlorine concentrations were approximately 2 orders of magnitude higher than the mercury concentrations, suggesting possible chlorine association with mercury.     

Characterization of size-fractionated particulate mercury in Shanghai ambient air

The size-fractionated particulate mercury in ambient air was collected at the top of a university campus building in Shanghai from March 2002 to September 2003. Wet digestion followed by cold vapor atom adsorption spectroscopy (CVAAS) was employed to analyze total particulate mercury concentration. Two-step extraction was performed to differentiate volatile particle-phase mercury (VPM), reactive particle-phase mercury (RPM) and inert particle-phase mercury (IPM). The average concentrations of mercury in PM_1.6, PM₈ and total suspended particle (TSP) were 0.058–0.252, 0.148–0.398 and 0.233–0.529 ng m⁻³, respectively. About 50%–60% of mercury in PM₈ was in PM_1.6, and about 60%–70% of mercury in TSP was in PM₈. Particulate mercury was mainly concentrated on fine particles. The mercury fraction in fine particulate matters (<1.6 μm) was over 4 μg g⁻¹ while 1–2 μg g⁻¹ in TSP. Both were much higher than background values, suggesting that anthropogenic sources are the predominant emission contributors. Seasonal variation indicated that the mercury in TSP in spring was higher than that in summer; however, the mercury in fine particles (<1.6 μm) varied little. The fact that fine particulate mercury (<1.6 μm) was well correlated with sulfate and elemental carbon, but not with fluoride, chloride, nitrate and organic carbon, demonstrates that fine particulate mercury is closely associated with stationary sources and gas–particle transformation. Speciation analysis of mercury showed that VPM fraction decreased with the decrease of particle size, while IPM fraction increased and occupied over 50% in particle <1.6 μm. The detailed species in VPM, RPM and IPM were discussed. Coal burning was estimated to contribute approximately 80% of total atmospheric mercury.     

Atmospheric mercury species in the European Arctic: Measurements and modelling

Concentrations of different species of mercury in arctic air and precipitation have been measured at Ny-Ålesund (Svalbard) and Pallas (Finland) during 1996–1997. Typical concentrations for vapour phase mercury measured at the two stations were in the range of 0.7–2 ng m⁻³ whereas particulate mercury concentrations were below 5 pg m⁻³. Total mercury in precipitation was in the range 3–30 ng l⁻¹. In order to evaluate the transport and deposition of mercury to the arctic from European anthropogenic sources, the Eulerian transport model HMET has been modified and extended to also include mercury species. A scheme for chemical conversion of elemental mercury to other species of mercury and deposition characteristics of different mercury species have been included in the model. European emission inventories for three different forms of Hg (Hg⁰, HgCl₂ and Hg_p) have been implemented in the numerical grid system for the HMET model.     

Atmospheric concentrations of ammonia and ammonium at an agricultural site in the southeast United States

In this study, we present ∼1 yr (October 1998–September 1999) of 12-hour mean ammonia (NH₃), ammonium (NH₄⁺), hydrochloric acid (HCl), chloride (Cl⁻), nitrate (NO₃⁻), nitric acid (HNO₃), nitrous acid (HONO), sulfate (SO₄²⁻), and sulfur dioxide (SO₂) concentrations measured at an agricultural site in North Carolina's Coastal Plain region. Mean gas concentrations were 0.46, 1.21, 0.54, 5.55, and 4.15 μg m⁻³ for HCl, HNO₃, HONO, NH₃, and SO₂, respectively. Mean aerosol concentrations were 1.44, 1.23, 0.08, and 3.37 μg m⁻³ for NH₄⁺, NO₃⁻, Cl⁻, and SO₄²⁻, respectively. Ammonia, NH₄⁺, HNO₃, and SO₄²⁻ exhibit higher concentrations during the summer, while higher SO₂ concentrations occur during winter. A meteorology-based multivariate regression model using temperature, wind speed, and wind direction explains 76% of the variation in 12-hour mean NH₃ concentrations (n=601). Ammonia concentration increases exponentially with temperature, which explains the majority of variation (54%) in 12-hour mean NH₃ concentrations. Dependence of NH₃ concentration on wind direction suggests a local source influence. Ammonia accounts for >70% of NH_x (NH_x=NH₃+NH₄⁺) during all seasons. Ammonium nitrate and sulfate aerosol formation does not appear to be NH₃ limited. Sulfate is primarily associated ammonium sulfate, rather than bisulfate, except during the winter when the ratio of NO₃⁻–NH₄⁺ is ∼0.66. The annual average NO₃⁻–NH₄⁺ ratio is ∼0.25.     

On the performance of a semi-continuous PM2.5 sulphate and nitrate instrument under high loadings of particulate and sulphur dioxide

The need for highly time-resolved data on atmospheric aerosol composition has prompted the development of several semi-continuous techniques in recent years. It is necessary to evaluate the performance of these new techniques under different meteorological and chemical conditions. We report on the results of intercomparison between a new commercial PM_2.5 semi-continuous sulphate and nitrate instrument (AIM, URG9000B) and filter-based technique. The study was carried out in the summer of 2005 in two polluted suburban/rural areas near Shanghai and Beijing, China, yielding unique results on the performance of this instrument in more polluted environments compared to most of the previously reported studies. The two methods had a good (R²>0.67) overall correlation for sulphate and nitrate, but showed discrepancies in absolute concentrations. At low levels of sulphate (<20 μg m⁻³) and SO₂ (<30 ppbv), the AIM data agreed with the filter result in Beijing (AIM=0.97×filter+0.60, R²=0.94). However, the semi-continuous instrument gave much higher sulphate values at high SO₂ concentrations (in Shanghai), which was due to a positive interference from SO₂ that broke through the denuder. At high sulphate loading, on the other hand, the AIM gave a much smaller sulphate reading, which was apparently due to an insufficient supply of water vapor to dissolve all the soluble ions under high aerosol loadings. For nitrate, while the two methods showed a good agreement in Shanghai (AIM=0.83×filter+0.00, R²=0.96), evaporative loss from the filters at high temperatures and negative bias in the AIM at high particle loading complicated the correlation in Beijing. Our study points out the need for careful evaluation and modification of the AIM for use in highly polluted environments. Under clean to moderately polluted conditions, the AIM can provide useful, highly time-resolved sulphate and nitrate data.     

Characteristics of atmospheric speciated mercury concentrations (TGM,Hg(II) and Hg(p)) in Seoul,Korea

Ambient speciated mercury concentrations including total gaseous mercury (TGM), gaseous divalent mercury (Hg(II)), and particulate mercury (Hg(p)) were measured on the roof of the Graduate School of Public Health building in Seoul, Korea from February 2005 to February 2006. The average concentrations were 3.22 ± 2.10 ng m^?3, 27.2 ± 19.3 pg m^?3, and 23.9 ± 19.6 pg m^?3 for TGM, Hg(II), and Hg(p), respectively. Hg(II) and Hg(p) concentrations were higher during the daytime than during the nighttime, probably because of high photochemical activity. Hg⁰ concentrations were not significantly correlated with ozone however a positive correlation between ozone and Hg(II) was found during periods of high humidity. Eighteen days were characterized as pollution events with 24 h average PM_2.5 concentrations >65 μg m^?3. The average concentrations of TGM and Hg(p) during these events were 1.4–2 times higher than those during non-pollution events. In order to identify the contribution of long-range transported mercury to the enhanced mercury concentrations in Korea, an episode was defined as a period with hourly average TGM and CO concentrations higher than the monthly average TGM and CO concentrations and with significant enhancement of both TGM and CO concentrations for at least 10 h. A total of 70 episodes were identified during the sampling period: 36 local episodes and 34 long-range transport episodes. The mean ΔTGM/ΔCO slope for all episodes was 0.0063 ng m^?3 ppbv^?1 which agreed well with the slope (0.0036–0.0074 ng m^?3 ppbv^?1) found in previous studies that identified long-range transport of TGM from China. The mean slope during non-events was 0.0011 ng m^?3 ppbv^?1. Back-trajectory analysis showed that during episodes, air parcels arrived mostly from the major industrial areas in China (n = 25, 73%), followed by Japan (n = 4, 12%), Yellow Sea (n = 3, 9%), and Russia (n = 2, 6%).     

Prevalence of low chlorinated dibenzo-p-dioxin/dibenzofurans in human serum

Mono- to tri-chlorinated dibenzo-p-dioxin/dibenzofurans (DD/Fs) have not been studied as extensively as the 17 toxic 2,3,7,8-substituted congeners. In this study for the first time, mono- to octa-chlorinated DD/Fs were analyzed for seventy one human serum samples collected from incinerator workers as well as residents living near and far from the facility. The mean concentrations of ∑Cl_1–8DD/Fs and 17-toxic congeners were 1890 and 398 pg g^?1 lipid (11.9 TEQ pg g^?1 lipid), respectively. 2,3,4,7,8-PeCDF, 1,2,3,7,8-PeCDD, and 1,2,3,6,7,8-HxCDD were predominant congeners that accounted for more than 78% of the TEQ concentrations. The profile for polychlorinated dibenzo-p-dioxins (PCDDs) was dominated by the most chlorinated congener, OCDD (>58%), while decreasing concentrations with increasing degree of chlorination were seen for polychlorinated dibenzofurans (PCDFs); MoCDFs (>83%) and DiCDFs (>6%). ∑Cl_1–3DD/Fs accounted for 77% of the serum concentrations of ∑Cl_1–8DD/Fs. These findings confirm that human beings are exposed to a large amount of ∑Cl_1–3DD/Fs. Moreover, MoCDFs contributed more than 60% of the ∑Cl_1–8DD/Fs and was highly correlated with ∑Cl_1–8DD/Fs. Thus, 2-MoCDF could be a predictive indicator for ∑Cl_1–8DD/Fs (r_s = 0.96), and the combination of 2-MoCDF and OCDD could explain the 95.9% variation in the serum of ∑Cl_1–8DD/Fs. These results suggest that low chlorinated DD/Fs should be studied extensively until these low chlorinated congeners will have been elucidated for their toxicities.     

Nitric acid and the origin and size segregation of aerosol nitrate aloft during BRACE 2002

As part of the BRACE 2002 May field intensive, the NOAA Twin Otter flew 21 missions over terrestrial, marine, and mixed terrestrial and marine sites in the greater Tampa, Florida, airshed including over Tampa Bay and the Gulf of Mexico. Aerosols were collected with filter packs and their inorganic fractions analyzed post hoc with ion chromatography. Anion mass dominated both the fine- (particle diameters ⩽2.5 μm) and coarse-mode (particle diameters 10.0–2.5 μm) inorganic fractions: SO₄²⁻in the fine fraction, 3.7 μg m⁻³ on average and Cl⁻ and NO₃⁻ in the coarse fraction, 0.6 μg m⁻³ on average and 1.4 μg m⁻³ on average, respectively. Ammonium ion dominated the inorganic fine-mode cation mass, averaging 1.2 μg m⁻³, presumably in association with SO₄². Coarse-mode cation mass was dominated by Na⁺, but the concentrations of Ca²⁺ and K⁺ together often equaled or exceeded the Na⁺ mass which was, on average, 0.6 μg m⁻³. Nitrate appeared predominantly in the coarse rather than the fine fraction, as expected, and the fine fraction never contributed >15% of the total NO₃ concentration. Nitric acid dominated the NO₃⁻ contribution from both aerosol size fractions, and constituted at least 45% of the total NO₃ in all samples. Coarse-mode Cl⁻ depletion, and hence NO₃⁻ replacement, reached 100% within the first 4 h of plume travel from the urban core in some samples, although it was most often less than 100% and slightly below the expected 1:1 ratio with coarse-mode NO₃⁻ concentration: the slope of the regression line of NO₃⁻ concentration to Cl⁻ depletion was 0.9 in the coarse fraction. In addition, terrestrial samples were markedly lower in Cl⁻ depletion, and thus in substituted NO₃^–, than were marine and mixed samples: 15–25% depletion in terrestrial samples vs. 50–65% in marine samples with the same air mass age. Thus, we conclude that NO₃⁻ and its progenitor compound HNO₃ were present in the Tampa airshed in insufficient amounts to titrate fully the slightly alkaline coarse-mode particles there, and to replace completely the Cl⁻ from the coarse-mode NaCl.     

The relationships between mercury and selenium in plankton and fish from a tropical food web

Background, aim, and scope  Selenium (Se) has been shown to reduce mercury (Hg) bioavailability and trophic transfer in aquatic ecosystems. The study of methylmercury (MeHg) and Se bioaccumulation by plankton is therefore of great significance in order to obtain a better understanding of the estuarine processes concerning Hg and Se accumulation and biomagnification throughout the food web. In the western South Atlantic, few studies have documented trace element and MeHg in fish tissues. No previous study about trace elements and MeHg in plankton has been conducted concerning tropical marine food webs. Se, Hg, and MeHg were determined in two size classes of plankton, microplankton (70–290 μm) and mesoplankton (≥290 μm), and also in muscle tissues and livers of four fish species of different trophic levels (Mugil liza, a planktivorous fish; Bagre spp., an omnivorous fish; Micropogonias furnieri, a benthic carnivorous fish; and Centropomus undecimalis, a pelagic carnivorous fish) from a polluted estuary in the Brazilian Southeast coast, Guanabara Bay. Biological and ecological factors such as body length, feeding habits, and trophic transfer were considered in order to outline the relationships between these two elements. The differences in trace element levels among the different trophic levels were investigated. Materials and methods  Fish were collected from July 2004 to August 2005 at Guanabara Bay. Plankton was collected from six locations within the bay in August 2005. Total mercury (THg) was determined by cold vapor atomic absorption spectrometry (CV-AAS) with sodium borohydride as a reducing agent. MeHg analysis was conducted by digesting samples with an alcoholic potassium hydroxide solution followed by dithizone-toluene extraction. MeHg was then identified and quantified in the toluene layer by gas chromatography with an electron capture detector (GC-ECD). Se was determined by AAS using graphite tube with Pin platform and Zeeman background correction. Results and discussion  Total mercury, MeHg, and Se increased with plankton size class. THg and Se values were below 2.0 and 4.8 μg g⁻¹ dry wt in microplankton and mesoplankton, respectively. A large excess of molar concentrations of Se in relation to THg was observed in both plankton size class and both fish tissues. Plankton presented the lowest concentrations of this element. In fish, the liver showed the highest THg and Se concentrations. THg and Se in muscle were higher in Centropomus undecimalis (3.4 and 25.5 nmol g⁻¹) than in Micropogonias furnieri (2.9 and 15.3 nmol g⁻¹), Bagre spp (1.3 and 3.4 nmol g⁻¹) and Mugil liza (0.3 and 5.1 nmol g⁻¹), respectively. The trophic transfer of THg and Se was observed between trophic levels from prey (considering microplankton and mesoplankton) to top predator (fish). The top predators in this ecosystem, Centropomus undecimalis and Micropogonias furnieri, presented similar MeHg concentrations in muscles and liver. Microplankton presented lower ratios of methylmercury to total mercury concentration (MeHg/THg) (34%) than those found in mesoplankton (69%) and in the muscle of planktivorous fish, Mugil liza (56%). The other fish species presented similar MeHg/THg in muscle tissue (of around 100%). M. liza showed lower MeHg/THg in the liver than C. undecimalis (35%), M. furnieri (31%) and Bagre spp. (22%). Significant positive linear relationships were observed between the molar concentrations of THg and Se in the muscle tissue of M. furnieri and M. liza. These fish species also showed significant inverse linear relationships between hepatic MeHg and Se, suggesting a strong antagonistic effect of Se on MeHg assimilation and accumulation. Conclusions  Differences found among the concentrations THg, MeHg, and Se in microplankton, mesozooplankton, and fishes were probably related to the preferred prey and bioavailability of these elements in the marine environment. The increasing concentration of MeHg and Se at successively higher trophic levels of the food web of Guanabara Bay corresponds to a transfer between trophic levels from the lower trophic level to the top-level predator, suggesting that MeHg and Se were biomagnified throughout the food web. Hg and Se were positively correlated with the fish standard length, suggesting that larger and older fish bioaccumulated more of these trace elements. THg, MeHg, and Se were a function of the plankton size. Recommendations and perspectives  There is a need to assess the role of selenium in mercury accumulation in tropical ecosystems. Without further studies of the speciation of selenium in livers of fishes from this region, the precise role of this element, if any, cannot be verified in positively affecting mercury accumulation. Further studies of this element in the study of marine species should include liver samples containing relatively high concentrations of mercury. A basin-wide survey of selenium in fishes is also recommended.     

Chemical composition of fine particles from incense burning in a large environmental chamber

 This study is aimed to characterize the major chemical compositions of PM_2.5 from incense burning in a large environmental chamber. Chemical analyses, including X-ray fluorescence for elemental species, ion chromatography for water soluble inorganic species (chloride, nitrate, sulfate, sodium, potassium, ammonium) and thermal/optical reflectance analysis for carbon species were carried out for combustion of three incense categories (traditional, aromatic and church incense). The average concentrations from incense burning ranged from 139.8 to 4414.7 μg m⁻³ for organic carbon (OC), and from 22.8 to 74.0 μg m⁻³ for elemental carbon (EC), respectively. The average OC and EC concentrations in PM_2.5 of three incense categories were in the order of church incense>traditional incense>aromatic incense. OC/EC ratios ranged from 7.0 to 39.1 for the traditional incense, with an average of 21.7; from 3.2 to 11.9 for the aromatic incense, with an average of 7.7. The concentrations of Cl⁻, SO₄²⁻, Na⁺ and K⁺ were highly variable. On average, the inorganic ion concentration sequence was traditional incense>church incense>aromatic incense. The profiles for elements were dominated by Na, Cl and K. In general, the major components in PM_2.5 fraction from incense burning are OC (especially OC2, OC3 and OC4), EC and K.     

A photochemical reactor for studies of atmospheric chemistry

A photochemical reactor for studies of atmospheric kinetics and spectroscopy has been built at the Copenhagen Center for Atmospheric Research. The reactor consists of a vacuum FTIR spectrometer coupled to a 100 L quartz cylinder by multipass optics mounted on electropolished stainless steel end flanges, surrounded by UV-A, UV-C and broadband sun lamps in a temperature-controlled housing. The combination of a quartz vessel and UV-C lamps allows higher concentrations of O(¹D) and OH than can be generated by similar chambers. The reactor is able to produce radical concentrations of ca. 8 × 10¹¹ cm^?3 for OH, 3 × 10⁶ cm^?3 for O(¹D), 3.3 × 10¹⁰ cm^?3 for O(³P) and 1.6 × 10¹² cm^?3 for Cl. The reactor can be operated at pressures from 10^?3 to 10³ mbar and temperatures from 240 to 330 K. As a test of the system we have studied the reaction CHCl₃ + Cl using the relative rate technique and find k_CHCl3+Cl/k_CH4+Cl = 1.03 ± 0.11, in good agreement with the accepted value.     

Chemical and strontium isotope characterization of rainwater in karst virgin forest,Southwest China

Strontium isotope ratios and concentrations of Ca²⁺, NH₄⁺, Na⁺, K⁺, Mg²⁺, Cl^?, SO₄^2?, NO₃^? and Al³⁺, Sr²⁺ were measured for 52 rainwater samples collected in virgin forest in a rural region between May 2007 and Dec. 2008. The rainwater pH values vary from 4.1 to 7.2 with a volume weight mean (VWM) value of 5.40. 40 of 52 samples have pH value above 5.0, indicating that the regional rainwater was not acidic. Among anions and cations, sulphate concentration (40.4 μeq l^?1, VWM) is the highest in the rainwater, followed by ammonium and calcium (30.2 and 20.8 μeq l^?1, VWM). Rainwater quality is characterized by low salinity and neutralized pH.The chemical compositions and ⁸⁷Sr/⁸⁶Sr ratios of the rainwater samples vary considerably. Using Na⁺ concentration as an indicator of marine origin, the proportions of sea salt and crustal elements were estimated from elemental ratios. The ⁸⁷Sr/⁸⁶Sr ratios were used to characterize different sources base on the data sets of this study and those from literatures. Such sources include weathering of limestone (⁸⁷Sr/⁸⁶Sr = 0.7075), remote soil dust (⁸⁷Sr/⁸⁶Sr > 0.7135) and anthropogenic source (fertilizers: ⁸⁷Sr/⁸⁶Sr = 0.7079). The results of the present study suggest that one likely source for high ammonium and calcium concentration is local soil. Due to a large contribution of these cations to the sulphate neutralization action, the rainwater in this region displays non-acidity, and thus has not significant environmental impact. The wet precipitation in the karst virgin forest in Guizhou province is strongly influenced by natural sources rather than anthropogenic sources.     

Fenton-like oxidation and mineralization of phenol using synthetic Fe(II)–Fe(III) green rusts

Background, aim, and scope  

In literature, the environmental applications of green rust (GR) have mainly been pointed out through the reduction of inorganic contaminants and the reductive dechlorination of chlorinated organics. However, reactions involving GR for the oxidation and mineralization of organic pollutants remain very scantly described. In this study, the ability of three synthetic Fe(II)–Fe(III) green rusts, GR(CO₃²⁻), GR(SO₄²⁻), and GR(Cl⁻), to promote Fenton-like reaction was examined by employing phenol as a model pollutant. Unlike the traditional Fenton’s reagent (dissolved Fe(II) + H₂O₂), where the pH values have to be lowered to less than 4, the proposed reaction can effectively oxidize the organic molecules at neutral pH and could avoid the initial acidification which may be costly and destructive for the in situ remediation of contaminated groundwater and soils. The green rust reactivity towards the oxidative transformation of phenol was thoroughly evaluated by performing a large kinetic study, chemical analyses, and spectroscopic investigations.     

The Effect of Coal Combustion Flue Gas Components on Low-Level Chlorine Speciation Using EPA Method 26A

ABSTRACT

U.S. Environmental Protection Agency (EPA) Method 26A is the recommended procedure for capturing and speci-ating halogen (X₂) and hydrogen halide (HX) stack emissions from combustion sources. Previous evaluation studies of Method 26A have focused primarily on hydrogen chloride (HCl) speciation. Capture efficiency, bias, and the potential interference of Cl₂ at high levels (>20 ppm [u,g/m³]) and NH₄Cl in the flue gas stream have been investigated. It has been suggested that precise Cl₂ measurement and accuracy in quantifying HX or X₂ using Method 26A are difficult to achieve at Cl₂ concentrations <5 ppm; however, no performance data exist to support this. Coal contains low levels of Cl, in the range of 5-2000 ppmw, which results in the presence of HCl and Cl₂ in the products of combustion. HCl is the predominant Cl compound formed in the high-temperature combustion process, and it persists in the gas as the products of combustion cool. Concentrations of Cl₂ in coal combustion flue gas at stack temperatures typically do not exceed 5 ppm. For this research, bench-scale experiments using simulated combustion flue gas were designed to validate the ability of Method 26A to speci-ate low levels of Cl₂ accurately. This paper presents the results of the bench-scale tests. The effect of various flue gas components is discussed. The results indicate that SO₂ is the only component in coal combustion flue gas that has an appreciable effect on Cl₂ distribution in Method 26A impingers, and that Method 26A cannot accurately speciate HCl and Cl₂ in coal combustion flue gas without modification.     

The influence of natural stressors on the toxicity of nickel to <Emphasis Type="Italic">Daphnia magna</Emphasis>

Global warming has become a source of awareness regarding the potential deleterious effects of extreme abiotic factors (e.g., temperature, dissolved oxygen (DO) levels) and also their influence on chemicals toxicity. In this work, we studied the combined effects of nickel and temperature (low and high levels) and nickel and low levels of DO to Daphnia magna, and concentration addition and independent action concepts as well as their deviations for synergism/antagonism, dose ratio and dose level dependency, were applied to survival and feeding rate data. Nickel single exposure showed an LC₅₀ value for 48 h of 7.36 mg l⁻¹ and an EC₅₀ value for feeding impairment at 2.41 mg l⁻¹. In the acute exposures to high and low temperatures, 50% of mortality was observed, respectively, at 30.7°C and 4.2°C whereas 50% reduction on the feeding activity was recorded at 22.6°C and 16.0°C. Relatively to low DO levels, a LC₅₀ value for 48 h of 0.5 mg l⁻¹ was obtained; feeding activity EC₅₀ value was 2 mg l⁻¹. On acute combined experiments, antagonism was observed for the combination of nickel and extreme temperatures, whereas a synergistic behaviour was observed in the combined exposure of nickel and low DO levels. At sublethal levels, nickel showed to be the main inducer of toxicity at high and low temperatures but not at low levels of dissolved oxygen. Toxicokinetics and toxicodynamics modelling studies should be made in the future to understand the toxicological pathways involved on complex combinations of stressors and to validate any conclusions.     

不同来源废水COD、TOC与Cl-的关系

通过对含盐化工废水(A)、受潮汐影响的河流水(B)、城市生活污水处理厂排水(C)、采油废水(D)4种不同来源废水进行为期15 d的采样监测,测定了其COD、TOC和Cl-浓度,分析比较了3种废水指标之间的关系,其中COD分别使用重铬酸钾法、氯气校正法和碘化钾碱性高锰酸钾法3种方法进行测定.实验结果表明,4种废水Cl-浓...     

The implementation of data reconciliation for evaluating a full-scale petrochemical wastewater treatment plant

Data reconciliation and mass balance analysis were conducted for the first time to improve the data obtained from a petrochemical wastewater treatment plant (WWTP), and the results were applied to evaluate the performance of the plant. Daily average values for 209 days from the inlet and outlet of the plant obtained from WWTP documentation center along with the results of four sampling runs in this work were used for data reconciliation and performance evaluation of the plant. Results showed that standard deviation and relative errors in the balanced data of each measurement decreased, especially for the process wastewater from 24.5 to 8.6 % for flow and 24.5 to 1.5 % for chemical oxygen demand (COD). The errors of measured data were −137 m³/day (−4.41 %) and 281 kg/day (7.92 %) for flow and COD, respectively. According to the balanced data, the removal rates of COD and 5-day biological oxygen demand (BOD₅) through the aeration unit were equal to 37 and 46 %, respectively. In addition, the COD and BOD₅ concentrations were reduced by about 61.9 % (2137 kg/day) and 78.1 % (1976 kg/day), respectively, prior to the biological process. At the same time, the removal rates of benzene, toluene, and styrene were 56, 38, and 69 %, respectively. The results revealed that about 40 % of influent benzene (75.5 kg/day) is emitted to the ambient air at the overhead of the equalization basin. It can be concluded that the volatilization of organic compounds is the basic mechanism for the removal of volatile organic compounds (VOCs) and it corresponds to the main part of total COD removal from the WWTP.

     

Acute effects of copper and mercury on the estuarine fish Pomatoschistus microps: Linking biomarkers to behaviour

The main objective of the present study was to investigate possible links between biomarkers and swimming performance in the estuarine fish Pomatoschistus microps acutely exposed to metals (copper and mercury). In independent bioassays, P. microps juveniles were individually exposed for 96 h to sub-lethal concentrations of copper or mercury. At the end of the assays, swimming performance of fish was measured using a device specially developed for epibenthic fish (SPEDE). Furthermore, the following biomarkers were measured: lipid peroxidation (LPO) and the activity of the enzymes acetylcholinesterase (AChE), lactate dehydrogenase (LDH), glutathione S-transferases (GST), 7-ethoxyresorufin-O-deethylase (EROD), superoxide dismutase (SOD), catalase (CAT), glutathione reductase (GR) and glutathione peroxidase (GPx). LC₅₀s of copper and mercury (dissolved throughout metal concentrations) at 96 h were 568 μg L⁻¹ and 62 μg L⁻¹, respectively. Significant and concentration-dependent effects of both metals on swimming resistance and covered distance against water flow were found at concentrations equal or higher than 50 μg L⁻¹ for copper and 3 μg L⁻¹ for mercury (dissolved throughout metal concentrations). These results indicate that SPEDE was efficacious to quantify behavioural alterations in the epibenthic fish P. microps at ecologically relevant concentrations. Significant alterations by both metals on biomarkers were found including: inhibition of AChE and EROD activities, induction of LDH, GST and anti-oxidant enzymes, and increased LPO levels, with LOEC values ranging from 25 to 200 μg L⁻¹ for copper and from 3 to 25 μg L⁻¹ for mercury (dissolved throughout metal concentrations). Furthermore, significant and positive correlations were found between some biomarkers (AChE and EROD) and behavioural parameters, while negative correlations were found for others (LPO, anti-oxidant enzymes and LDH) suggesting that disruption of cholinergic function through AChE inhibition, decreased detoxification capability due to EROD inhibition, additional energetic demands to face chemical stress, and oxidative stress and damage may contribute to decrease the swimming performance of fish. Since a reduced swimming capability of fish may reduce their ability to capture preys, avoid predators, and interfere with social and reproductive behaviour, the exposure of P. microps to copper and/or mercury concentrations similar to those tested here may decrease the fitness of wild populations of this species.     

Mercury emission trend influenced by stringent air pollutants regulation for coal-fired power plants in Korea

Regulatory control of mercury emission from anthropogenic sources has become a global concern in the recent past. Coal-fired power plants are one of the largest sources of anthropogenic mercury emission into the atmosphere. This paper summarizes the current reducing trend of mercury emission as co-beneficial effect by more stringent regulation changes to control primary air pollutants with introducing test results from the commercial coal-fired facilities and suggesting a guideline for future regulatory development in Korea. On average, mercury emission concentrations ranged 16.3–2.7 μg Sm^?3, 2.4–1.1 μg Sm^?3, 3.1–0.7 μg Sm^?3 from anthracite coal-fired power plants equipped with electrostatic precipitator (ESP), bituminous coal-fired power plants with ESP + flue gas desulphurization (FGD) and bituminous coal-fired power plants with selective catalytic reactor (SCR) + cold side (CS) ? ESP + wet FGD, respectively. Among the existing air pollution control devices, the best configuration for mercury removal in coal-fired power plants was SCR + CS ? ESP + wet FGD, which were installed due to the stringent regulation changes to control primary air pollutants emission such as SO₂, NOx and dust. It was estimated that uncontrolled and controlled mercury emission from coal-fired power plants as 10.3 ton yr^?1 and 3.2 ton yr^?1 respectively. After the installation of ESP, FGD and SCR system, following the enforcement of the stringent regulation, 7.1 ton yr^?1 of mercury emission has been reduced (nearly 69%) from coal-fired power plants as a co-benefit control. Based on the overall study, a sample guideline including emission limits were suggested which will be applied to develop a countermeasure for controlling mercury emission from coal-fired power plants.