鸡蛋壳制备乙酸钙冰雪融化剂的研究

以鸡蛋壳为原料,对高温煅烧分解蛋壳、中和法制备乙酸钙(CA)的最佳反应条件进行了研究,试验结果表明:在反应温度为50 ℃、配料摩尔比为CaO∶乙酸＝1∶2.8、乙酸浓度为15 mol/L、石灰乳浓度(以氧化钙计)为1.3 mol/L时CA产量最大.产品融冰试验表明:CA在环境温度-10℃以上使用时,其融冰效果较好.     

从废甲醇合成催化剂中回收铜锌

将废RK-05甲醇合成催化剂经过煅烧、浸取、精制等工序回收其中的铜和锌。经正交实验得到煅烧废催化剂的最优工艺参数为:废催化剂筛目100目,煅烧温度950℃,煅烧时间60 min。最佳浸取工艺条件为:废催化剂加入量约4 g/L,浸取温度75℃,浸取剂用量与理论用量体积比2.0~3.0,浸取剂浓度4.0 mol/L,浸取时间10min。精制工序制备CuO的最佳工艺条件为:锌粒与滤渣质量比为1.00,反应时间3 h,煅烧温度450℃,煅烧时间4 h。制备ZnO的最佳工艺条件为:煅烧温度800℃,煅烧时间60 min。回收的产品CuO纯度为99.1%,满足GB/T674—2003《化学试剂粉状氧化铜》中优级品的标准。回收的产品ZnO纯度为99.6%,满足GB/T3185—1992《氧化锌(间接法)》中一级品的标准。     

酸洗废液制备高纯氧化铁红

以钢板酸洗废液为原料,采用铁粉预处理、除杂、合成、水洗、干燥、煅烧等工序制备高纯氧化铁红.最佳工艺条件为:预处理温度80℃,预处理时间3h,铁粉加入量为理论值的1.5倍;除杂温度65 ℃,聚丙烯酰胺加入量60 mg/L;米用将FeC12溶液和饱和NH4HCO3溶液同时滴加入反应器的方式进行沉淀反应;煅烧温度800℃.在此工艺条件下处理酸洗废液,可制得纯度为99.3％的高纯氧化铁红.     

废甲醇催化剂的回收和利用

介绍了利用废甲醇催化剂生产活性氧化锌和五水硫酸铜的方法，试验结果表明，最佳工艺条件为：催化剂粒度80目；酸浸反应的硫酸浓度3．6则mol/L，100g原料中硫酸用量325mL；净化反应的pH控制在5—5．5，温度85℃；活性氧化锌煅烧温度800℃；铜粉焙烧温度600℃，通风量0．8L／min，焙烧时间2．5h；硫酸铜生产过程中，反应温度为60—80℃，时间2h。该方法具有工艺简单、操作方便、产品质量好的特点，并可减少环境污染，变废为宝，具有较好的经济效益。     

MnO_2陶粒臭氧氧化催化剂的制备及其性能

以凹凸棒土为载体、MnO_2为活性组分,制备了MnO_2陶粒臭氧氧化催化剂,并以草酸为模拟污染物,采用响应面法对催化剂的制备条件进行了优化。实验结果表明:各因素对草酸去除率影响的显著性顺序为MnO_2投加量盐酸溶液质量分数煅烧时间煅烧温度。催化剂的最佳制备条件为:MnO_2投加量200 mg/g,盐酸溶液质量分数20%,煅烧时间2 h,煅烧温度400℃。在初始草酸质量浓度150 mg/L、溶液pH 3.11、臭氧投加量8.10 mg/min、臭氧-氧气曝气量400 m L/min的条件下,最佳条件制备的催化剂在反应30 min时的草酸去除率达66.99%。催化剂具有良好的活性稳定性,且催化过程中Mn~(2+)溶出量低。催化剂具有较大的比表面积,负载的MnO_2类型为α-MnO_2和β-MnO_2。     

粉煤灰的改性及其吸附性能

以改性粉煤灰为吸附剂,对亚甲基蓝溶液进行吸附实验。经正交实验确定改性粉煤灰的最佳制备条件:煅烧温度为850℃,粉煤灰与ZnCl2的质量比为2∶2,盐酸加入量为2.4mol/L,粉煤灰粒径为16.8mm。在亚甲基蓝溶液初始质量浓度为10mg/L、改性粉煤灰加入量为200mg/L、振荡时间为3.0h、溶液pH为5、吸附温度为25℃的条件下,亚甲基蓝的降解率和溶液脱色率分别达86.24%和82.76%。     

以酸洗废液为原料制备FeCl2工艺研究

研究了不锈钢酸洗废液经除杂、蒸发浓缩、冷却结晶、高温焙烧的工艺,成功制得FeCl₂产品。其除杂最佳条件是：还原铁粉添加量1.1eq,p H3.5,结晶最佳温度是30℃;焙烧最佳条件是：草酸添加量为2%,焙烧温度250℃,焙烧时间2 h,在N₂气氛炉下焙烧即可得到纯度≥99%的FeCl₂产品,实现了酸洗废液资源化再生利用。     

尖晶石型铝酸盐光催化还原CO_2

采用有机物前驱法制备了3种尖晶石型铝酸盐催化剂(CoAl_2O_4,ZnAl_2O_4,CoAl_2O_4)。采用FTIR,XRD,UV-Vis DRS等技术对催化剂进行表征,并将催化剂应用于CO_2的光催化还原。表征结果显示:除CoAl_2O_4外,CoAl_2O_4和ZnAl_2O_4在煅烧时均直接形成尖晶石相;CoAl_2O_4,CoAl_2O_4,ZnAl_2O_4的平均粒径分别为25.21,21.35,23.26 nm,禁带宽度分别为1.77,1.45,3.82 eV。分别以煅烧温度为900℃、煅烧时间为4 h时制得的ZnAl_2O_4,CoAl_2O_4,CoAl_2O_4为催化剂,在催化剂加入量为1.5 g/L、CO_2流量为200 mL/min、反应温度为60℃的条件下光催化反应8 h,甲酸产生量分别为443.54,365.65,241.39μmol/g。     

硫酸渣制备高纯度硫酸亚铁

以高铁硫酸渣为原料,采用酸浸一还原-除杂-结晶-重结晶-干燥工艺,合成高纯度硫酸亚铁.通过反应温度、反应时闻对硫酸渣中铁的浸出率的影响,以及结晶温度、干燥温度,干燥时间、于燥时间对硫酸亚铁产品纯度的影响做分析实验,得出最佳酸浸条件:硫酸渣与硫酸的固液比为1:3,硫酸质量分数为20%-25%,反应温度为80℃,反应时间为6 h,搅拌强度为200 r/min;最佳结晶精制条件:结晶溶液pH值1:3,温度为60℃,温度海60℃;除杂最佳条件:pH值约为4.5;冷却结晶温度控制在20℃,结晶秣过程为30℃于燥6 h.     

高浓度酚醛树脂生产废水的预处理

采用二次缩合反应预处理高浓度酚醛树脂生产废水。一次反应的最佳工艺条件为：甲醛加入量0.010 0 mL/mL，Ba（OH）2加入量0.005 g/mL，反应时间3 h，反应温度85 ℃。最佳工艺条件下的一次反应COD去除率为 52.9%。二次反应中，当反应温度为80 ℃、反应时间为3 h、尿素加入量为3 g/L时，二次反应COD去除率最高，为31.5%。COD=85 000 mg/L、ρ（挥发酚）= 12 000 mg/L、ρ（甲醛）=6 740 mg/L的废水经两次缩合反应处理后，出水中COD=27 400 mg/L，COD的总去除率为67.8%;ρ（挥发酚）=2 400 mg/L，挥发酚的总去除率达80.0%;ρ（甲醛）= 980 mg/L，甲醛的总去除率达84.9%。处理1 t废水还可回收酚醛树脂6.75 kg。     

Effects of calcium hydroxide and calcium chloride addition to bentonite in iron ore pelletization.

Pyrite ash is created as waste from the roasting of pyrite ores during the production of sulphuric acid. These processes generate great amounts of pyrite ash waste that is generally land filled. This creates serious environmental pollution due to the release of acids and toxic substances. Pyrite ash waste can be utilized in the iron production industry as a blast furnace feed to process this waste and prevent environmental pollution. The essential parameters affecting the pelletization process of pyrite ash were studied using bentonite as a binder. Experiments were then carried out using bentonite and a mixture of bentonite with calcium hydroxide and calcium chloride in order to make the bentonite more effective. The metallurgical properties of pyrite ash, bentonite, calcium hydroxide, calcium chloride, a mixture of these and sintered pellets were studied using X-ray analysis. The crushing strength tests were carried out to investigate the strength of pyrite ash waste pellets. The results of these analyses showed that pyrite ash can be agglomerated to pellets and used in the iron production industry as a blast furnace feed. The crushing strength of the pellets containing calcium hydroxide and calcium chloride in addition to bentonite was better than the strength of pellets prepared using only bentonite binder.     

Recovery of iron oxide and calcium chloride from an iron-rich chloride waste using calcium carbonate

Journal of Material Cycles and Waste Management - The ilmenite-chloride process has used for the production of TiCl4 from the ilmenite (FeTiO3) ore, which produces cyclone dust containing mostly...     

Conversion of calcium sulphide to calcium carbonate during the process of recovery of elemental sulphur from gypsum waste

The production of elemental sulphur and calcium carbonate (CaCO₃) from gypsum waste can be achieved by thermally reducing the waste into calcium sulphide (CaS), which is then subjected to a direct aqueous carbonation step for the generation of hydrogen sulphide (H₂S) and CaCO₃. H₂S can subsequently be converted to elemental sulphur via the commercially available chemical catalytic Claus process. This study investigated the carbonation of CaS by examining both the solution chemistry of the process and the properties of the formed carbonated product. CaS was successfully converted into CaCO₃; however, the reaction yielded low-grade carbonate products (i.e. <90 mass% as CaCO₃) which comprised a mixture of two CaCO₃ polymorphs (calcite and vaterite), as well as trace minerals originating from the starting material. These products could replace the Sappi Enstra CaCO₃ (69 mass% CaCO₃), a by-product from the paper industry which is used in many full-scale AMD neutralisation plants but is becoming insufficient. The insight gained is now also being used to develop and optimize an indirect aqueous CaS carbonation process for the production of high-grade CaCO₃ (i.e. >99 mass% as CaCO₃) or precipitated calcium carbonate (PCC).     

次氯酸钙溶液的脱硫脱硝特性

采用Ca(ClO)2溶液在高效反应瓶中与模拟烟气进行脱硫脱硝实验,考察了模拟烟气中SO2和NOx的去除效果,以动力学为理论基础研究了Ca(ClO)2的脱硫脱硝性能。实验结果表明:在模拟烟气中SO2,NO,NO2的质量浓度分别为3700,1300,820 mg/m^3及Ca(ClO)2溶液浓度为0.35 mol/L的条件下,SO2去除率达到100%,NOx去除率达到67%。脱硫过程中吸收液中的ClO-是100%脱硫率的保障。Ca^2+吸收SO2的反应速率呈现一级反应的特征。得到的脱硫产物CaSO4·2H2O达到了工业石膏的品质要求。同时脱硫脱硝时NOx和SO2具有协同作用。     

Mechanochemical dechlorination of polyvinyl chloride with calcium sulfates

Polyvinyl chloride (PVC) was milled with hydrated or unhydrated calcium sulfates (CaSO₄·2H₂O or CaSO₄) in air by using a planetary mill to investigate mechanochemical dechlorination behavior. The milling process resulted in size reduction and in the breaking of bonds leading to mechanically induced solid state reaction, forming CaCl₂ and dechlorinated hydrocarbon with C=C double bonds in the product. Washing the milled mixtures with water at room temperature allowed removal of the chloride formed during milling, and more than 95% of the chlorine in PVC was removed from a mixture milled for 4 h. This process could offer a potential route for the handling and disposal of both PVC and gypsum wastes. H₂S gas was generated during milling; more H₂S was released from the unhydrated sample than from the hydrated sample.     

有机钙硫氮协同控制技术研究

有机钙硫氮协同脱除技术是一种极具应用前景的污染物综合控制技术。分析了有机钙硫氮协同脱除的机理及影响因素，介绍了该技术在国内外的研究发展状况。     

Study of nitrogen oxide absorption in the calcium sulfite slurry

Experiments were conducted using a bubbling reactor to investigate nitrogen oxide absorption in the calcium sulfite slurry. The effects of CaSO₃ concentration, NO₂/NO mole ratio and O₂ concentrations on NO₂ and SO₂ absorption efficiencies were investigated. Five types of additives, including MgSO₄, Na₂SO₄, FeSO₄, MgSO₄/Na₂SO₄ and FeSO₄/Na₂SO₄, had been evaluated for enhancing NO₂ absorption in CaSO₃ slurry. Results showed that CaSO₃ concentration had significant impact on NO₂ and SO₂ absorption efficiencies, and the highest absorption efficiencies of SO₂ and NO₂ could reach about 99.5 and 75.0 %, respectively. Furthermore, the NO₂ absorption was closely related to the NO₂/NO mole ratio, and the existence of NO₂ in flue gas may promote NO absorption. The presence of O₂ in simulated flue gas was disadvantage for NO _x removal because it can oxidize sulfite to sulfate. It was worth pointing out that FeSO₄/Na₂SO₄ was the best additive among those investigated additives, as the NO₂ removal efficiency was significantly increased from 74.8 to 95.0 %. IC and in situ FTIR results suggest that the main products were NO₃ ^? and NO₂ ^? in liquid phase and N₂O, N₂O₅ and HNO₃ in gas phase during the CaSO₃ absorption process.     

过氧化钙降解有机污染物研究进展

CaO₂具有很好的稳定性,可在水和土壤中逐步分解生成H₂O₂成为氧化反应的氧化剂,已作为H₂O₂的替代物用于环保领域的研究中。介绍了CaO₂的作用机理,综述了CaO₂用于处理含卤代物、染料、抗生素、苯系物等废水的研究进展,以及CaO₂用于治理含石油烃、多环芳烃、苯系物和农药的污染土壤的研究进展。提出未来的研究方向：充分利用CaO₂水解生成O₂和H₂O₂的特性,探索化学与生物联合修复技术;探究CaO₂与其他氧化剂联用技术,从而增加CaO₂修复技术的适用性和经济性。     

钙法提钒尾渣的浮选脱硫试验

根据钙法提钒尾渣的矿物特性,采用浮选法分离其中的石膏以实现脱硫,分别考察了矿浆pH、矿浆液固比、捕收剂添加量及浮选中水循环次数等因素对浮选指标的影响,并进行了理论分析,确定了钙法提钒尾渣浮选脱硫的优选工艺参数。试验结果表明,在矿浆pH为7、矿浆液固比为5∶1、捕收剂添加量为0.6~0.8 kg/t的条件下,可获得w（S）低于0.3%、w（Fe）约为34%的富铁料,S脱除率可达95%,Fe回收率约为90%。     

湿法烟气脱硫中亚硫酸钙氧化技术的研究进展

分析了国内外湿法脱硫工艺中亚硫酸钙的氧化反应控制因素研究成果，指出浆液pH值一般控制在4．5—5，采用Mn^2＋作为催化剂时，CaSO3有较高的氧化效率。对我国亚硫酸钙氧化技术的继续研究提出了一些建议，为湿法脱硫工艺设计提供参考。