Homogeneous degradation of 1,2,9,10-tetrachlorodecane in aqueous solutions using hydrogen peroxide, iron and UV light

The homogeneous degradation of the polychlorinated n-alkane, 1,2,9,10-tetrachlorodecane (T4C10), was studied in aqueous solutions of hydrogen peroxide, including Fenton and photo-Fenton reaction conditions. All solutions were adjusted to a pH of 2.8 and an ionic strength of 0.1 M NaClO4 prior to photolysis. T4C10 (2 x 10(-6) M) was substantially degraded by the H2O2/UV system (1.0 x 10(-2) M H2O2), with 60% disappearance in 20 min of irradiation in a photoreactor equipped with 300 nm lamps of light intensity 3.6 x 10(-5) Ein L(-1) min(-1) (established by ferrioxalate actinometry). The reaction produced stoichiometric amounts of chloride ion indicating complete dechlorination of the chlorinated n-alkane. T4C10 degraded very slowly under Fenton (Fe2+/H2O2/dark) and Fenton-like (Fe3+/H2O2/dark) conditions. However, when the same solutions were irradiated, T4C10 degraded more rapidly than in the H2O2/UV system, with 61% disappearance in 10 min of exposure. The rapid degradation is related to the enhanced degradation of hydrogen peroxide to oxidizing *OH radicals under photo-Fenton conditions. Degradation was inhibited in both the H2O2/UV and photo-Fenton systems by the addition of KI and tert-butyl alcohol due to *OH scavenging.     

Spatial and Geographical Variations of Urban, Suburban and Rural Atmospheric Concentrations of Phenols and Nitrophenols (7 pp)

Goal, Scope and Background Atmospheric sampling (gas and particles) of 5 phenols (phenol, m-cresol, p-cresol, o-cresol, pentachlorophenol) and 15 nitrophenols (3-methyl-2-nitrophenol, 3-nitrophenol, 4-methyl-2-nitrophenol, 5-methyl-2-nitrophenol, 2-methyl-3nitrophenol, 3-methyl-4-nitrophenol, 2,6-dinitrophenol, bromoxynil, 2,5-dinitrophenol, 2,6-dinitro-p-cresol, 2,4-dinitrophenol, ioxynil, DNOC, 3,4-dinitrophenol, dinoseb) on XAD-2 resin (20 gr) and glass fibre filters, respectively, were performed in 2002 by using 'Digitel DA80' high volume samplers. These measurements were undertaken in order to show spatial and geographical variations of concentrations and the role of traffic in the emissions of these compounds to the atmosphere. Methods Sampling were performed in Strasbourg (eastern France), in its vicinity (Schiltigheim) and in Erstein. Sites were chosen to be representative of urban (Strasbourg), suburban (Schiltigheim) and rural (Erstein) conditions. Field campaigns were undertaken simultaneously in urban and suburban sites during all the seasons during 4 hours at a flow rate of 60 m3.h-1, which gives a total of 240 m3 of air per sample. Period of sampling varied between 06h00 to 10h00, 11h00 to 15h00 and 18h00 to 22h00 in order to evaluate a variation of concentration during automobile traffic between urban, suburban and rural areas. Gas and particle samples were separately Soxhlet extracted for 12 h with a mixture of CH2Cl2 / n-hexane (50:50 v/v), concentrated to about 1 mL with a rotary evaporated and finally dried under nitrogen. Dry extracts were dissolved in 1 mL of CH3CN. Before analysis, extracts were sylilated by using MTBSTFA. Analysis was performed by GC/MSD in the SIM mode. Results and Discussion Partitioning of phenolic compounds between gas and particle phases seems to be mainly correlated with vapour pressure. Among phenolic compounds analysed, phenol, p-cresol, pentachlorophenol and 2.4-dinitrophenol were detected in all samples and emissions from traffic seems to be the major source for the presence of these compounds to the atmosphere. No increase of concentrations in autumn tend to confirm this hypothesis since, with the use of domestic heating in colder months, increases of PAHs concentrations were observed and these compounds are known to be emitted by all combustion processes. Pentachlorophenol is a special case since this molecule is only used as wood preservative. Its presence in all atmospheric samples, whatever the locations and the period of time is the consequence of its persistence. Conclusions and Perspectives These measurements demonstrate that phenols and nitrophenols are emitted to the atmosphere and further measurements, in order to confirm their sources, their behaviour and their potential impact to the air quality and to human health should be undertaken especially since the literature collected is relatively old. Concentrations of pentachlorophenol measured are very low and, due to its toxicity, further investigations should be undertaken. - * The basis of this peer-reviewed paper is a presentation at the 9th FECS Conference on 'Chemistry and Environment', 29 August to 1 September 2004, Bordeaux, France.     

Oxidation of TNT by photo-Fenton process

A series of photo-Fenton reactions have been performed for the degradation of 2,4,6-trinitrotoluene (TNT) in a 4.2-l reactor. The degradation reaction rate of TNT followed a pseudo-first-order behavior; and the rate constants for 2.4mW cm(-2)UV only, 2.4mW cm(-2)UV/H(2)O(2), Fenton, photo-Fenton (2.4mW cm(-2)) and photo-Fenton (4.7mW cm(-2)) were 0.002min(-1), 0.007min(-1), 0.014min(-1), 0.025min(-1) and 0.037min(-1), respectively. Increasing the intensity of UV light, and the concentrations of ferrous ions and hydrogen peroxide promoted the oxidation rate under the experimental conditions in this study. The weighting factor (f), the Fe(II)-promoted efficiency (r) and the promoted-UV light efficiency (p) were calculated to clarify their effects on the TNT oxidation. Moreover, the inhibition effect of hydroxyl radical was also observed in both Fenton and photo-Fenton oxidation when the concentration of Fe(II) were higher than 2.88mM. Solid phase micro-extraction was first applied to the separation of the organic byproducts from TNT oxidation. GC/MS was employed to identify the byproducts during the Fenton and photo-Fenton oxidation of TNT. These compounds were clarified as 1,3,5-trinitrobenzene, 1-methyl-2,4-dinitrobenzene 2,5-dinitrobenzoic acid and 1,3-dinitrobenzene. By these byproducts, the mechanisms of the methyl group oxidation, decarboxylation, aromatic ring breakage, and hydrolysis can be recognized and demonstrated. The pathway of TNT oxidation by photo-Fenton process was also proposed in this study.     

The role of ferrous ion in Fenton and photo-Fenton processes for the degradation of phenol

The efficiency of different Fenton-related oxidative processes such as Fenton, solar-Fenton and UV-Fenton were examined using phenol as a model compound in simulated and industrial wastewater. A batch study was conducted to optimize parameters like pH, hydrogen peroxide concentration and ferrous ion concentration governing the Fenton process. At optimum conditions, different Fenton-related processes were compared for the degradation of phenol. Increased degradation and mineralisation efficiency were observed in photo-Fenton processes as compared to conventional Fenton process. The maximum mineralising efficiency for phenol with Fenton, solar and UV-Fenton processes were 41%, 96% and 97% respectively. In Fenton process, carboxylic acids like acetic acid and oxalic acid were formed as end products during the degradation of phenol while in photo-Fenton processes, both these ions were identified during the early stages of phenol degradation and were oxidized almost completely at 120 min of the reaction time. In photo-Fenton processes (solar and UV light) complete degradation were observed with 0.4 mM of Fe2+ catalyst as compared to 0.8 mM of Fe2+ in conventional Fenton process. In Fenton and solar-Fenton processes, an iron reusability study was performed to minimize the amount of iron used in treatment process. The efficacy of Fenton and solar-Fenton processes was applied to effluent from phenol resin-manufacturing unit for the removal and mineralisation of phenol.     

Wet deposition of pesticides and nitrophenols at two sites in Denmark: measurements and contributions from regional sources

The concentrations of selected pesticides, of some of their degradation products and nitrophenols in rain were measured at two stations in Denmark in the period January 2000-July 2001. Forty compounds were quantified at least at one station during at least one sampling period. Additionally 17 compounds could be detected but not quantified, and 22 compounds could not be detected at all. The highest depositions of pesticides were observed for pendimethalin and desethylterbuthylazine, which is a degradation product of terbuthylazine. The deposition of the nitrophenols 2,4-dinitrophenol, DNOC, 3-methyl-4-nitrophenol was much higher than that of pesticides. The deposition of 2,4-dinitrophenol was e.g. up to a factor of 40 higher than that of pendimethalin. Atrazine, chloridazon, 2,4-D, dieldrin, disulfoton, fenitrothion, isoproturon, lenacil, metazachlor and propachlor were found in precipitation, although these pesticides are not allowed in Denmark. It can therefore be concluded that they came from abroad and have been transported over at least 60-80 km. For some of these compounds the transport distance is much longer.     

Kinetic degradation of the pollutant guaiacol by dark Fenton and solar photo-Fenton processes

This work is first intended to optimize the experimental conditions for the maximum degradation of guaiacol (2-methoxyphenol) by Fenton’s reagent, and second, to improve the process efficiency through the use of solar radiation. Guaiacol is considered as a model compound of pulp and paper mill effluent. The experiments were carried out in a laboratory-scale reactor subjected or not to solar radiation. Hydrogen peroxide solution was continuously introduced into the reactor at a constant flow rate. The kinetics of organic matter decay was evaluated by means of the chemical oxygen demand (COD) and the absorbance measurements. The experimental results showed that the Fenton and solar photo-Fenton systems lead successfully to 90% elimination of COD and absorbance at 604 nm from a guaiacol solution under particular experimental conditions. The COD removal always obeyed a pseudo-first-order kinetics. The effect of pH, temperature, H₂O₂ dosing rate, initial concentration of Fe²⁺, and initial COD was investigated using the Fenton process. The solar photo-Fenton system needed less time and consequently less quantity of H₂O₂. Under the optimum experimental conditions, the solar photo-Fenton process needs a dose of H₂O₂ 40% lower than that used in the Fenton process to remove 90% of COD.     

Degradation of chlordecone and beta-hexachlorocyclohexane by photolysis, (photo-)fenton oxidation and ozonation

Intensive use of chlorinated pesticides from the 1960s to the 1990s has resulted in a diffuse contamination of soils and surface waters in the banana-producing areas of the French West Indies. The purpose of this research was, for the first time, to examine the degradation of two of these persistent pollutants – chlordecone (CLD) and beta-hexachlorocyclohexane (β-HCH) in 1 mg L^?1 synthetic aqueous solutions by means of photolysis, (photo-) Fenton oxidation and ozonation processes. Fenton oxidation is not efficient for CLD and yields less than 15% reduction of β-HCH concentration in 5 h. Conversely, both molecules can be quantitatively converted under UV-Vis irradiation reaching 100% of degradation in 5 h, while combination with hydrogen peroxide and ferrous iron does not show any significant improvement except in high wavelength range (>280 nm). Ozonation exhibits comparable but lower degradation rates than UV processes. Preliminary identification of degradation products indicated that hydrochlordecone was formed during photo-Fenton oxidation of CLD, while for β-HCH the major product peak exhibited C₃H₃Cl₂ as most abundant fragment.     

Measurement of phase-distributed nitrophenols in Rome ambient air

Atmospheric nitrophenols (NPs) were determined both in the gas and particle phases by combining the annular denuder sampling technique with GC-MS analysis. The phase distribution of six mono-NPs identified in air sampled in downtown Rome was assessed. 4-NP, 3-methyl-4-NP and 2,6-dimethyl-4-NP were found for more than 75% in the particle phase, whilst 2-NP, 4-methyl-2-NP and 5-methyl-2-NP predominated in the gas phase. Concentration levels lower than 20 ng m-3 were observed for all NPs, among which 4-NP (17.8+/-5.6 ng m-3) and 2-NP (10.4+/-4.2 ng m-3) were the most abundant congeners in the two phases, respectively.     

Abatement and degradation pathways of toluene in indoor air by positive corona discharge

Indoor air concentrations of volatile organic compounds often exceed outdoor levels by a factor of 5. There is much interest in developing new technologies in order to improve indoor air quality. In this work non-thermal plasma (DC positive corona discharge) is explored as an innovative technology for indoor air purification. An inlet gas stream of 10 l min(-1) containing 0.50+/-0.02 ppm toluene was treated by the plasma reactor in atmospheric conditions. Toluene removal proved to be achievable with a characteristic energy density epsilon(0) of 50 J l(-1). Removal efficiencies were higher for 26% relative humidity (epsilon(0)=35 J l(-1)), compared with those at increased humidities (50% relative humidity, epsilon(0)=49 J l(-1)). Reaction products such as formic acid, benzaldehyde, benzyl alcohol, 3-methyl-4-nitrophenol, 4-methyl-2-nitrophenol, 4-methyl-2-propyl furan, 5-methyl-2-nitrophenol, 4-nitrophenol, 2-methyl-4,6-dinitrophenol are identified by means of mass spectrometry. Based on these by-products a toluene degradation mechanism is proposed.     

Fe/活性炭多相类Fenton法湿式氧化罗丹明B废水的研究

采用自制的Fe/活性炭（Fe/AC）为催化剂,H₂O₂为氧化剂,组成多相类Fenton试剂催化降解罗丹明B染料废水。实验结果表明,在催化剂加入量为0.8 g/L,H₂O₂体积分数为0.3%,废水pH值为13,反应时间为30 min的条件下,质量浓度为200 mg/L的罗丹明B染料废水的脱色率达100%。反应动力学研究表明,罗丹明B脱色反应近似为一级反应,30℃时反应速率常数为0.02675 min^-1,表观活化能为69.47 kJ/mol。     

CuO/γ-Al_2O_3类Fenton试剂降解丁基黄药

CuO/γ-Al2O3类Fenton试剂是降解丁基黄药的优良试剂。该试剂与传统的Fenton试剂相比,提高了反应的pH值,可在较高pH（4~5）条件下反应,而传统的Fenton试剂的适宜pH值一般在3以下。采用单因素实验和正交实验相结合的方法研究了pH、催化剂投加量、过氧化氢投加量以及反应时间对丁基黄药降解效果的影响,并对催化剂的使用寿命进行了探讨。研究结果表明,反应的最佳条件为：pH为4~5,催化剂投加量为6 g/L,过氧化氢用量为30 mg/L,反应30min。在此反应条件下,丁基黄药的降解率达98%以上;影响丁基黄药降解效果的因素大小顺序为：pH〉反应时间〉H2O2用量〉催化剂投加量,其中pH对CuO/γ-Al2O3类Fenton试剂降解丁基黄药的影响最为显著。     

Parathion degradation and its intermediate formation by Fenton process in neutral environment

The purpose of this study is to investigate parathion degradation by Fenton process in neutral environment. The initial parathion concentration for all the degradation experiments was 20 ppm. For hydrogen ion effect on Fenton degradation, the pH varied from 2 to 8 at the [H₂O₂] to [Fe²⁺] ratio of 2-2 mM, and the result showed pH 3 as the most effective environment for parathion degradation by Fenton process. Apparent degradation was also observed at pH 7. The subsequent analysis for parathion degradation was conducted at pH 7 because most environmental parathion exists in the neutral environment. Comparing the parathion degradation results at various Fenton dosages revealed that at Fe²⁺ concentrations of 0.5, 1.0 and 1.5 mM, the Fenton reagent ratio ([H₂O₂]/[Fe²⁺]) for best-removing performance were found as 4, 3, and 2, resulting in the removal efficiencies of 19%, 48% and 36%, respectively. Further increase in Fe²⁺ concentration did not cause any increase of the optimum Fenton reagent ratio for the best parathion removal. The result from LC-MS also indicated that hydroxyl radicals might attack the PS double bond, the single bonds connecting nitro-group, nitrophenol, or the single bond within ethyl groups of parathion molecules forming paraoxons, nitrophenols, nitrate/nitrite, thiophosphates, and other smaller molecules. Lastly, the parathion degradation by Fenton process at the presence of humic acids was investigated, and the results showed that the presence of 10 mg L⁻¹ of humic acids in the aqueous solution enhanced the parathion removal by Fenton process twice as much as that without the presence of humic acids.     

Enhanced degradation of polycyclic aromatic hydrocarbons by biodegradation combined with a modified Fenton reaction

A study has been conducted to enhance degradation of a mixture of polycyclic aromatic hydrocarbons (PAHs) by combining biodegradation with hydrogen peroxide oxidation in a former manufactured gas plant (MGP) soil. An active bacterial consortium enriched from the MGP surface soil (0-2 m) biodegraded more than 90% of PAHs including 2-, 3-, and 4-ring hydrocarbons in a model soil. The consortium was also able to transform about 50% of 4- and 5-ring hydrocarbons in the MGP soil. As a chemical oxidant, Fenton's reagent (H2O2 + Fe2+) was very efficient in the destruction of a mixture of PAHs (i.e., naphthalene (NAP), fluorene (FLU), phenanthrene (PHE), anthracene (ANT), pyrene (PYR), chrysene (CHR), and benzo(a)pyrene (BaP)) in the model soil; noticeably, 84.5% and 96.7% of initial PYR and BaP were degraded, respectively. In the MGP soil, the same treatment destroyed more than 80% of 2- and 3-ring hydrocarbons and 20-40% of 4- and 5-ring compounds. However, the low pH requirement (pH 2-3) for optimum Fenton reaction made the process incompatible with biological treatment and posed potential hazards to the soil ecosystem where the reagent was used. In order to overcome such limitation, a modified Fenton-type reaction was performed at near neutral pH by using ferric ions and chelating agents such as catechol and gallic acid. By the combined treatment of the modified Fenton reaction and biodegradation, more than 98% of 2- or 3-ring hydrocarbons and between 70% and 85% of 4- or 5-ring compounds were degraded in the MGP soil, while maintaining its pH about 6-6.5.     

Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

Fe(III)–EDDS complex in Fenton and photo-Fenton processes: from the radical formation to the degradation of a target compound

The present work compares the efficiency of homogenous Fenton and photo-Fenton processes in the presence of Fe(III)–EDDS complex under different experimental conditions. 4-tert-Butylphenol (4-t-BP), which is one of the endocrine disrupting chemicals, was used as a model pollutant to investigate the Fenton and photo-Fenton application. The efficiency of homogenous photo-Fenton process was significantly much higher than homogenous Fenton process, which is due to the rapid formation of Fe²⁺ under UV irradiation of the iron complex and the photochemical formation of HO^? from the photolysis of the complex Fe(III)–EDDS. Through the degradation of 4-t-BP, the effect of Fe(III)–EDDS concentration, H₂O₂ concentration, pH, and oxygen was investigated in both processes. Such trend was also correlated with pH calculating the polychromatic Fe²⁺ quantum yield formation at pH 4.0, 6.0, and 8.6. The results showed that at high Fe(III)–EDDS and H₂O₂ concentrations, a negative effect was found. By the way, the Fenton process was found to be enhanced at basic pH. These results can be very useful for the use and optimization of such iron complex in water treatment process as function of different physico-chemical conditions.     

Fenton试剂对富营养化湖水黑臭的氧化降解作用

通过室内实验,研究Fenton试剂对富营养化水体黑臭物质氧化降解作用。实验结果表明,在黑臭的富营养化水中投加Fenton试剂20 min后,水体臭味明显降低,90 min后水体臭味全部消除;水体浊度、色度有显著改善,水体浊度、色度去除率分别达73.73%和93.11%,显著高于对照组的53.4%和22%;水体溶解氧量显著提高;水体的pH值保持在7左右。鱼类毒理实验结果表明,最佳剂量的Fenton试剂对实验鱼类无急性毒性作用。     

类Fenton反应对偶氮染料橙黄II的脱色研究

以橙黄II染料溶液为研究对象,通过正交实验确定了Fe-NTA/H2O2构成的类Fenton反应中各影响因子的最佳操作条件为:[H2O2]=20 mmol/L,[Fe-NTA]=2.5 mmol/L,pH=3。同时考察了反应时间、溶液pH值、H2O2浓度、Fe-NTA浓度对脱色效率的影响。实验表明脱色反应在30 m in内基本完成,类Fenton试剂能在较宽的pH范围内保持较好的脱色效果,而且在pH=6时,类Fenton试剂比传统Fenton试剂的脱色效率提高约75%。增加双氧水浓度可以提高橙黄II溶液脱色率,但超过20 mmol/L后效果提高不明显。在0.5~2.5 mmol/L的范围内,Fe-NTA浓度对脱色效果的影响不显著。     

Conditioning of aluminium-based water treatment sludge with Fenton's reagent: effectiveness and optimising study to improve dewaterability

Alternative conditioning of aluminium-based drinking water treatment sludge using Fenton reagent (Fe2+/H2O2) was examined in this study. Focuses were placed on effectiveness and factors to affect such novel application of Fenton process. Experiments have demonstrated that considerable improvement of alum sludge dewaterability evaluated by capillary suction time (CST) can be obtained at the relative low concentrations of Fenton reagent. A Box-Behnken experimental design based on the response surface methodology was applied to evaluate the optimum of the influencing variables, i.e. iron concentration, hydrogen peroxide concentration and pH. The optimal values for Fe2+, H2O2, and pH are 21 mg g(-1)DS(-1)(dry solids), 105 mg g(-1)DS(-1) and 6, respectively, at which the CST reduction efficiency of 48+/-3% can be achieved, this agreed with that predicted by an established polynomial model in this study.     

Intermediate distributions and primary yields of phenolic products in nitrobenzene degradation by Fenton's reagent

Nitrobenzene thermal degradation was investigated using the Fenton reagent in different experimental conditions. Reaction products were analyzed by HPLC, GC-MS, LC-MS and IC. The products obtained at different nitrobenzene conversion degrees show that degradation mainly involves successive hydroxylation steps of the aromatic ring and its subsequent opening followed by oxidation of corresponding aliphatic compounds. Our results show as primary reaction products: 4-nitrophenol, 3-nitrophenol, 2-nitrophenol, phenol and 1,3-dinitrobenzene, indicating that both hydroxylation and nitration reactions are involved. The formation of phenolic products can be explained by postulating an initial step of HO() addition to nitrobenzene ring. The mechanisms of primary reaction pathways are discussed and a detailed kinetic analysis to obtain the true primary yields of phenolic products is proposed. The relative yields observed for nitrophenol isomers do not follow the expected orientation according to deactivating characteristics of the nitro group but significantly depend on Fe(+2), Fe(+3), H(2)O(2) and O(2) concentrations. The understanding of the effect of reaction conditions on the relative product distribution benefits the application of Fenton and Fenton-like systems to waste water treatment.     

Chemical absorption process for degradation of VOC gas using heterogeneous gas-liquid photocatalytic oxidation: toluene degradation by photo-Fenton reaction

A novel process for degradation of toluene in the gas-phase using heterogeneous gas-liquid photocatalytic oxidation has been developed. The degradation of toluene gas by photo-Fenton reaction in the liquid-phase has experimentally examined. The photo-Fenton reaction in the liquid-phase could improve the overall toluene absorption rate by increasing the driving force for mass transfer and as a result enhance the removal of toluene in the exhaust gas. The toluene concentrations in the inlet gas were varied in the range from 0.0968 to 8.69gm(-3) with initial hydrogen peroxide concentration of 400mgl(-1) and Fe dose of 5.0mgl(-1). It was found that toluene in the inlet gas was almost completely dissolved into water and degraded in the liquid-phase for the inlet toluene gas concentration of less than 0.42gm(-3). The dynamic process of toluene gas degradation by the photo-Fenton reaction providing information for reaction kinetics and mass transfer rate was examined. Toluene removal kinetic analysis indicated that photo-Fenton degradation was significantly affected by H(2)O(2) concentration. The experimental results were satisfactorily described by the predictions simulated using the simplified tanks-in-series model combined with toluene removal kinetic analysis. The present results showed that the proposed chemical absorption process using the photo-Fenton heterogeneous gas-liquid photocatalytic oxidation is very effective for degradation of volatile organic gases.