Effect of sulfur dioxide and sulfite on photochemical energy storage of isolated chloroplasts--a photoacoustic study

Photoacoustic spectroscopy was used to study the effect of sulfite and SO(2) on isolated corn mesophyll chloroplasts by monitoring the photochemical energy storage. Sulfite incubation of isolated chloroplasts, either in light or in darkness, caused a decrease in photochemical energy storage. The more pronounced decrease in light indicates a light-dependent sulfite inhibitory site(s) in chloroplasts. Also diphenylcarbazide caused a partial recovery of energy storage in sulfite treated chloroplasts indicating a possible site of damage at the water oxidizing system. Although the chloroplast membranes were found to be insensitive to high concentrations of SO(2) for relatively short exposure periods (10 min) in light, exposure of chloroplasts to 28.5 ng cm(-3) SO(2) for 10 min caused a decrease in energy storage. An attempt was made to explain the mechanism of action of sulfite and SO(2) in chloroplasts.     

Potential revenue and breakeven of energy storage systems in PJM energy markets

Environmental Science and Pollution Research - The operation in energy arbitrage markets is an attractive possibility to energy storage systems developers and owners to justify an investment in...     

Property-enhanced paraffin-based composite phase change material for thermal energy storage: a review

Environmental Science and Pollution Research - Research on phase change material (PCM) for thermal energy storage is playing a significant role in energy management industry. However, some hurdles...     

Comparing domestic versus imported apples: A focus on energy use

GOAL, SCOPE AND BACKGROUND: The issue of whether food miles are a relevant indicator for the environmental impacts associated with foods has received significant attention in recent years. It is suggested here that issues other than the distance travelled need to be considered. The argument is presented by illustrating the case for the provision of apples. MATERIALS AND METHODS: The effects of variability in primary energy requirements for apple cultivation and for other life cycle stages, seasonality (timing of consumption) and loss of produce during storage are studied in this paper, by comparing apples from different supplier countries for consumption in Europe. RESULTS: Data sources for primary energy use (PEU) of apple production are identified ranging from 0.4-3.8 MJ/kg apples for European and Southern American countries and 0.4-0.7 MJ/kg for New Zealand. This variability is related to different yields and producer management practices in the different countries. Storage loss may range from 5% to 40% for storage periods between 4 and 10 months, and this has a significant effect on the results (e.g. increasing the total PEU by 8-16% when stored for 5-9 months in Europe as compared with a no loss and no storage situation). The storage periods and related storage losses change markedly through the year for imported (i.e. non-European) versus European apples. DISCUSSION: The timing of consumption and related storage losses need to be included in the assessment, as this affects the order of preference for locally sourced versus imported apples. The variability in energy requirements in different life cycle stages, but particularly for the fruit production stage, is also significant in this comparative analysis. CONCLUSIONS: Overall, it seems that there are similarities in the total PEU ranges for European and New Zealand apples during the Southern Hemisphere's apple season (European spring and summer). However, during the European autumn and winter (Northern Hemisphere apple season) PEU values are generally higher for apples imported from the Southern Hemisphere compared with European apples consumed in Europe. However, this latter observation may not hold true where apples for consumption in one European country are imported from another European country, because energy use for road transportation has a significant influence on the result. RECOMMENDATIONS AND PERSPECTIVES: Future studies comparing alternative sources of fresh produce need to account for ranges of data for the fruit production and storage stages, which reflect the seasonality of production.     

利用太阳能驱动的一体化氧化沟的运行方式

污水处理的高能耗和新能源利用已引起人们的关注,本文根据太阳光照强度的周期变化和农村污水昼夜排放量悬殊的特征,提出了一种新型的利用无蓄电池太阳能光伏系统驱动的污水生物处理系统,可有效降低太阳能光伏系统的成本。生物反应器是一个双沟式一体化氧化沟。按照启动的用电设备的数量,一体化氧化沟具有5种运行方式。在不同的运行方式下,一体化氧化沟的内沟和外沟具有不同的功能,其中运行方式3到运行方式5对污染物去除效率最高。采用阶梯型电量输出模式,可以充分利用太阳能,并保障一体化氧化沟的高效运行时间。在160 d的连续运行实验中,COD、氨氮、总氮和总磷的平均去除率分别为87.8%、98.4%、68.7%和80.3%。证明无蓄电池太阳能光伏系统驱动污水生物反应器处理农村分散污水是可行的。     

Green and facile synthesis of nickel oxide-porous carbon composite as improved electrochemical electrodes for supercapacitor application from banana peel waste

Environmental Science and Pollution Research - Lithium-ion batteries and supercapacitors are examples of energy storage technologies that have a lot of promise in a variety of applications. Herein,...     

Performance analysis of crushed gravel sand heat storage and biomass evaporator-assisted single slope solar still

Environmental Science and Pollution Research - In this research work, the productivity, energy, exergy, and economic and enviro-economic performance in crushed gravel sand heat storage and biomass...     

Life cycle implications of urban green infrastructure

Low Impact Development (LID) is part of a new paradigm in urban water management that aims to decentralize water storage and movement functions within urban watersheds. LID strategies can restore ecosystem functions and reduce runoff loadings to municipal water pollution control facilities (WPCF). This research examines the avoided energy and greenhouse gas (GHG) emissions of select LID strategies using life cycle assessment (LCA) and a stochastic urban watershed model. We estimate annual energy savings and avoided GHG emissions of 7.3 GJ and 0.4 metric tons, respectively, for a LID strategy implemented in a neighborhood in New York City. Annual savings are small compared to the energy and GHG intensity of the LID materials, resulting in slow environmental payback times. This preliminary analysis suggests that if implemented throughout an urban watershed, LID strategies may have important energy cost savings to WPCF, and can make progress towards reducing their carbon footprint.     

Optimizing the position of insulating materials in flat roofs exposed to sunshine to gain minimum heat into buildings under periodic heat transfer conditions

Building roofs are responsible for the huge heat gain in buildings. In the present work, an analysis of the influence of insulation location inside a flat roof exposed directly to the sun’s radiation was performed to reduce heat gain in buildings. The unsteady thermal response parameters of the building roof such as admittance, transmittance, decrement factor, and time lags have been investigated by solving a one-dimensional diffusion equation under convective periodic boundary conditions. Theoretical results of four types of walls were compared with the experimental results available in literature. The results reveal that the roof with insulation placed at the outer side and at the center plane of the roof is the most energy efficient from the lower decrement factor point of view and the roof with insulation placed at the center plane and the inner side of the roof is the best from the highest time lag point of view among the seven studied configurations. The composite roof with expanded polystyrene insulation located at the outer side and at the center plane of the roof is found to be the best roof from the lowest decrement factor (0.130) point of view, and the composite roof with resin-bonded mineral wool insulation located at the center plane and at the inner side of the roof is found to be energy efficient from the highest time lag point (9.33 h) of view among the seven configurations with five different insulation materials studied. The optimum fabric energy storage thicknesses of reinforced cement concrete, expanded polystyrene, foam glass, rock wool, rice husk, resin-bonded mineral wool, and cement plaster were computed. From the results, it is concluded that rock wool has the least optimum fabric energy storage thickness (0.114 m) among the seven studied building roof materials.     

A review on ex situ mineral carbonation

The increased CO₂ quantities in the environment have led to many harmful effects. Therefore, it is very important to decrease the CO₂ levels in the environment. CO₂ capture along with safe and permanent storage using mineral CO₂ sequestration method can play an important role to reduce carbon emissions into the environment. Mineral sequestration is a stable storage method that provides long-term storage and an appropriate substitute for the more popular geological storage method. The process is most suited for places where there is a lack of underground cavities for underground geological storage. Minerals rich in Ca and Mg are used predominantly in carbonation reactions. In addition, those alkaline wastes that are rich in Mg and Ca such as cement waste, steel slag and many process ashes can also be employed in CO₂ sequestration. Mineral carbonation could be used for the sequestration of billions of tonnes of CO₂ every year. However, various drawbacks related to mineral carbonation still need to be addressed, such as resolving the slow rate of reactions, necessity of large amounts of feedstock, decreasing the high overall cost of CO₂ sequestration and reducing the huge energy requirements to accelerate the carbonation reaction. This study explores a number of carbonation methods, parameters that control the process and future potential applications of carbonated products.

     

Food (miles) for Thought - Energy Balance for Locally-grown versus Imported Apple Fruit (3 pp)

- This commentary compares the primary energy requirement for apples (cultivar ‘Braeburn’), which were either imported or locally-grown in Meckenheim, Germany. Imported apples of the same cultivar were grown in a Southern hemisphere winter in Nelson, Southland, New Zealand, and were picked at the end of March with subsequent 28 d transport by sea for sale in April in Germany. Locally-grown apples (cultivar ‘Braeburn’) were picked in mid-October and required a primary energy of nearly 6 MJ/kg of fruit including 0.8 MJoule/kg for five months CA storage at 1°C during a Northern hemisphere winter until mid-March. This compared favourably with 7.5 MJoule/kg for overseas shipment from New Zealand, i.e. a ca. 27% greater energy requirement for these imported fruits. Overall, the primary energy requirement of regional produce, stored several months on-site, partially compensated for the larger energy required to import fresh fruit from overseas. This result is in marked contrast to reported overestimates of a reported up to 8-fold energy requirement for domestic versus imported apple juice concentrate [7]. Our own findings of less primary energy required for domestic apple fruit is discussed with respect to providing local employment, fruit orchards preserving the countryside, quality assurance systems for local fruit such as QS and EUREP-GAP, networking and other factors favouring regional production.     

Challenges and opportunities of power systems from smart homes to super-grids

The world’s power systems are facing a structural change including liberalization of markets and integration of renewable energy sources. This paper describes the challenges that lie ahead in this process and points out avenues for overcoming different problems at different scopes, ranging from individual homes to international super-grids. We apply energy system models at those different scopes and find a trade-off between technical and social complexity. Small-scale systems would require technological breakthroughs, especially for storage, but individual agents can and do already start to build and operate such systems. In contrast, large-scale systems could potentially be more efficient from a techno-economic point of view. However, new political frameworks are required that enable long-term cooperation among sovereign entities through mutual trust. Which scope first achieves its breakthrough is not clear yet.     

Design of optimized PI controller for 7-level inverter: a new control strategy

Photovoltaic (PV) system produces electricity that differs from variations in environmental parameters such as temperature and solar radiation. The PV network will operate at maximum power point (MPP) and deal with an ever-increasing energy demand, that changes from both load and weather conditions.” Moreover, energy storage devices could be a potential solution for improving the efficiency and performance of renewable energy sources (RES). This paper intends to establish a control design by an optimization-assisted PI controller for a 7-level inverter. Accordingly, the gains of PI controller are adjusted dynamically by FireFly Integrated-Sea Lion Optimization algorithm (FFI-SLnO) that integrates the concepts of both Sea Lion Optimization (SLnO) and FireFly algorithm (FF). The gains should be tuned such that the error among the reference signal and fault signal should be low and hence better dynamic performance can be obtained by the presented optimized PI controller. Finally, the performance of the proposed method is compared over other traditional models with respect to certain measures and its superiority is proved.

     

Global climate change: The quantifiable sustainability challenge

Population growth and the pressures spawned by increasing demands for energy and resource-intensive goods, foods, and services are driving unsustainable growth in greenhouse gas (GHG) emissions. Recent GHG emission trends are consistent with worst-case scenarios of the previous decade. Dramatic and near-term emission reductions likely will be needed to ameliorate the potential deleterious impacts of climate change. To achieve such reductions, fundamental changes are required in the way that energy is generated and used. New technologies must be developed and deployed at a rapid rate. Advances in carbon capture and storage, renewable, nuclear, and transportation technologies are particularly important; however, global research and development efforts related to these technologies currently appear to fall short relative to needs. Even with a proactive and international mitigation effort, humanity will need to adapt to climate change, but the adaptation needs and damages will be far greater if mitigation activities are not pursued in earnest. In this review, research is highlighted that indicates increasing global and regional temperatures and ties climate changes to increasing GHG emissions. GHG mitigation targets necessary for limiting future global temperature increases are discussed, including how factors such as population growth and the growing energy intensity of the developing world will make these reduction targets more challenging. Potential technological pathways for meeting emission reduction targets are examined, barriers are discussed, and global and U.S. modeling results are presented that suggest that the necessary pathways will require radically transformed electric and mobile sectors. While geoengineering options have been proposed to allow more time for serious emission reductions, these measures are at the conceptual stage with many unanswered cost, environmental, and political issues.

Implications:?This paper lays out the case that mitigating the potential for catastrophic climate change will be a monumental challenge, requiring the global community to transform its energy system in an aggressive, coordinated, and timely manner. If this challenge is to be met, new technologies will have to be developed and deployed at a rapid rate. Advances in carbon capture and storage, renewable, nuclear, and transportation technologies are particularly important. Even with an aggressive international mitigation effort, humanity will still need to adapt to significant climate change.     

The energy balance of central Mexico City during the dry season

The first measurements of the energy balance fluxes of a dry, densely built-up, central city site are presented. Direct observation of the net radiation, sensible and latent heat flux densities above roof-top in the old city district of Mexico City allow the heat storage flux density to be found by residual. The most important finding is that during daytime, when evaporation is very small (<4% of net radiation), and therefore sensible heat uses dominate (Bowen ratio >8), the uptake of heat by the buildings and substrate is so large (58%) that convective heating of the atmosphere is reduced to a smaller role than expected (38%). The nocturnal release of heat from storage is equal to or larger than the net radiation and sufficient to maintain an upward convective heat flux throughout most nights. It is important to see if this pattern is repeated at other central city, or dry urban sites, or whether it is only found in districts dominated by massive stone structures. These findings have implications for the height of the urban mixing layer and the magnitude of the urban heat island.     

European Community Can Reduce CO2 Emissions by Sixty Percent: A Feasibility Study

Carbon dioxide (CO₂,) emissions in the European Community (EC) can be reduced by roughly 60 percent. A great many measures need to be taken to reach this reduction, with a total annual cost of ECU 55 milliard. Fossil fuel use is the main cause of CO2 emissions into the atmosphere; CO₂ emissions are to a large extent responsible for the greenhouse effect. Energy saving (conservation) and nuclear energy appear to be the least expensive methods of CO₂, abatement, directly followed by renewables. More expensive alternatives include the separation of CO₂, at the source (e.g., power plants), followed by storage in depleted gas fields, aquifers, or in the ocean. Biological options, such as reforestation and energy farming, are the most expensive abatement methods; however, they do have secondary advantages, such as avoided fallow premiums and avoided export premiums on cereals. Application of all measures together can lead to the 60 percent reduction goal.     

Understanding regional metabolism for a sustainable development of urban systems

Cities are the most complex forms of settlements which man has built in the course of his cultural development. Their “metabolism” is connected with the world economy and is run mainly by fossil energy carriers. Up to now there are no validated models for the evaluation of a sustainable development of urban regions. The guidelines for a “sustainable development” suggest the reduction of resource consumption. The article is concerned with the problem of how the “sustainable-development concept” can be transformed from a global to a regional scale. In urban settlements the strategy of final storage should be applied. By this, the subsystem waste management can be transformed within 10 to 15 years to a “sustainable status”. With regard to the system “agronomy”, the article concludes that agriculture in urban systems should focus on food production instead of promoting reduction of food production in favour of energy plants, which is not a suitable strategy. The main problems are the energy carriers. Transformation to a “sustainble status” is only possible by a reconstruction of the urban system, i.e. of buildings and the transportation network. The rate determining step in achieving such a status is the change in the fabric of buildings and in the type of transportation networks. The reconstruction of an urban system needs, mainly for economical reasons, a time period of two generations.     

A temperature-profile method for estimating flow in geologic heat pipes

Above-boiling temperature conditions, as encountered, for example, in geothermal reservoirs and in geologic repositories for the storage of heat-producing radioactive wastes, may induce strong liquid and gas flow processes in porous subsurface environments. The magnitude of these flow processes is extremely hard to measure in the field. We therefore propose a simple temperature-profile method that uses high-resolution temperature data for deriving such information. The energy that is transmitted with the vapor and water flow creates a nearly isothermal zone maintained at about the boiling temperature, referred to as a heat pipe. Characteristic features of measured temperature profiles, such as the differences in the gradients inside and outside of the heat-pipe regions, are used to derive the approximate magnitude of the liquid and gas fluxes in the subsurface.     

Separation and capture of CO2 from large stationary sources and sequestration in geological formations--coalbeds and deep saline aquifers

The topic of global warming as a result of increased atmospheric CO2 concentration is arguably the most important environmental issue that the world faces today. It is a global problem that will need to be solved on a global level. The link between anthropogenic emissions of CO2 with increased atmospheric CO2 levels and, in turn, with increased global temperatures has been well established and accepted by the world. International organizations such as the United Nations Framework Convention on Climate Change (UNFCCC) and the Intergovernmental Panel on Climate Change (IPCC) have been formed to address this issue. Three options are being explored to stabilize atmospheric levels of greenhouse gases (GHGs) and global temperatures without severely and negatively impacting standard of living: (1) increasing energy efficiency, (2) switching to less carbon-intensive sources of energy, and (3) carbon sequestration. To be successful, all three options must be used in concert. The third option is the subject of this review. Specifically, this review will cover the capture and geologic sequestration of CO2 generated from large point sources, namely fossil-fuel-fired power gasification plants. Sequestration of CO2 in geological formations is necessary to meet the President's Global Climate Change Initiative target of an 18% reduction in GHG intensity by 2012. Further, the best strategy to stabilize the atmospheric concentration of CO2 results from a multifaceted approach where sequestration of CO2 into geological formations is combined with increased efficiency in electric power generation and utilization, increased conservation, increased use of lower carbon-intensity fuels, and increased use of nuclear energy and renewables. This review covers the separation and capture of CO2 from both flue gas and fuel gas using wet scrubbing technologies, dry regenerable sorbents, membranes, cryogenics, pressure and temperature swing adsorption, and other advanced concepts. Existing commercial CO2 capture facilities at electric power-generating stations based on the use of monoethanolamine are described, as is the Rectisol process used by Dakota Gasification to separate and capture CO2 from a coal gasifier. Two technologies for storage of the captured CO2 are reviewed--sequestration in deep unmineable coalbeds with concomitant recovery of CH4 and sequestration in deep saline aquifers. Key issues for both of these techniques include estimating the potential storage capacity, the storage integrity, and the physical and chemical processes that are initiated by injecting CO2 underground. Recent studies using computer modeling as well as laboratory and field experimentation are presented here. In addition, several projects have been initiated in which CO2 is injected into a deep coal seam or saline aquifer. The current status of several such projects is discussed. Included is a commercial-scale project in which a million tons of CO2 are injected annually into an aquifer under the North Sea in Norway. The review makes the case that this can all be accomplished safely with off-the-shelf technologies. However, substantial research and development must be performed to reduce the cost, decrease the risks, and increase the safety of sequestration technologies. This review also includes discussion of possible problems related to deep injection of CO2. There are safety concerns that need to be addressed because of the possibilities of leakage to the surface and induced seismic activity. These issues are presented along with a case study of a similar incident in the past. It is clear that monitoring and verification of storage will be a crucial part of all geological sequestration practices so that such problems may be avoided. Available techniques include direct measurement of CO2 and CH4 surface soil fluxes, the use of chemical tracers, and underground 4-D seismic monitoring. Ten new hypotheses were formulated to describe what happens when CO2 is pumped into a coal seam. These hypotheses provide significant insight into the fundamental chemical, physical, and thermodynamic phenomena that occur during coal seam sequestration of CO2.     

模拟成藏地质填埋及诱导填埋有机质生气的理论初探

填埋处理和垃圾生物气的开发利用是实现城市生活垃圾资源化、无害化、减量化处理的有效途径,引入模拟生物气成藏和含气系统的思路,开展地质填埋与诱导填埋有机质生气研究是对能源地质学和填埋设计理念的新探索.通过对比研究地质填埋结构与地质学中生物气藏系统的异同点、生气机理和影响因素的共性与差异,初步论证了将模拟生物气藏理论引入地质填埋设计、优化地质填埋结构、提高填埋有机质生物气化效率和抽排利用效率的可行性;探讨了生物气藏理论在构建地质填埋结构中的可能应用和启示.研究表明:模拟生物气藏地质填埋设计和非常规生物气开发理念具有理论依据和现实基础;生物气藏生、储、盖要素和运、圈、保过程的模拟可应用于垃圾地质填埋场的构建,微生物地球化学理论有助于对诱导填埋有机质生气条件优化的认识.