Adsorption and removal of antimony from aqueous solution by an activated Alumina

The adsorption of Sb(V) ions from aqueous solutions onto commercially available activated alumina (AA) was investigated. AA has a much higher adsorption capacity than presently used adsorbents. Sb(V) ions are likely adsorbed through electrostatic attraction and/or specific adsorption mechanism, while the optimum pH is found in the range of 2.8–4.3. The Sb(V) ions adsorption capacities increase with increasing temperature. The addition of nitrate, acetate, arsenite, chloride, and silicate ions affected Sb(V) ions adsorption only slightly, while the coexisting ascorbate, arsenate, phosphate, sulfate, EDTA, tartrate, and citrate ions substantially depressed Sb(V) ions adsorption.     

Arsenic removal using natural biomaterial-based sorbents

Arsenic contamination of water is a major problem worldwide. A possible solution can be approached through developing new sorbents based on cost-effective and environmentally friendly natural biomaterials. We have developed new sorbents based on biomaterial impregnation with iron oxyhydroxide. In this study, raw peat material, iron-modified peat, iron-modified biomass (shingles, straw, sands, cane and moss) as well as iron humate were used for the removal of arsenate from contaminated water. The highest sorption capacity was observed in iron-modified peat, and kinetic studies indicated that the amount of arsenic sorbed on this material exceeds 90 % in 5 h. Arsenate sorption on iron-modified peat is characterised by the pseudo-second-order mechanism. The results of arsenic sorption in the presence of competing substances indicated that sulphate, nitrate, chloride and tartrate anions have practically no influence on As(V) sorption onto Fe-modified peat, whereas the presence of phosphate ions and humic acid significantly lowers the arsenic removal efficiency.     

The removal of arsenic from water with natural and modified clinoptilolite

The presence of increased arsenic concentrations in Eastern Croatia is a consequence of the geological composition of the soil. Because of its known harmful effects, arsenic removal is of high importance and adsorption represents an attractive and economically efficient approach to arsenic removal. The use of zeolites obtained from the Donje Jesenje deposit, Croatia (CZ) and the Zlatokop deposit in Vranjska Banja, Serbia (SZ) in Na- and Fe–Na-modified forms was investigated in order to effectively remove arsenate and arsenite from aqueous solutions. The adsorption kinetics of arsenic was studied as a function of the initial arsenate and arsenite concentrations (30–300 μg · L^?1), equilibration time (3–48 h), pH (5–10) and in the presence of sulfate and phosphate at initial concentrations of 0.2–0.5 mg · L^?1. In order to estimate sorption constants designating the sorption capacity and affinity of the zeolites samples, the experimental results were fitted to the Langmuir and Freundlich sorption isotherms. Desorption tests conducted with 1–3 mol · L^?1 HCl indicated that arsenate sorption was irreversible. The results obtained indicated that use of the Serbian zeolite in the Fe–Na-modified form (Fe–Na-SZ) was favourable for arsenate removal from water containing up to 30 μg As · L^?1.     

Arsenic and chromate removal from water by iron chips—Effects of anions

The purpose of this study is to estimate the removal efficiency of As and Cr (VI) by one kind of industrial waste — iron chips, as well as to estimate the effects of typical inorganic anions (sulfate, phosphate, and nitrate), and typical organic anions (citrate, oxalate, and humate) on As or Cr (VI) removal. The results showed that 98% of As (V) and 92% of As (III) could be removed from aqueous phase by the iron chips within 60 min. Compared with As species, Cr (VI) was removed much more rapidly and efficiently with 97% of Cr (VI) being removed within 25 min. The removal efficiency for arsenic was in the order: As (III) (sulfate), As (III) (nitrate) or As (III), As (III) (humate), As (III) (oxalate), As (III) (citrate), As (III) (phosphate), and for chromate was in the order: Cr (VI) (sulfate), Cr (VI) (phosphate) or Cr (VI) (nitrate) or Cr (VI) (oxalate), Cr (VI), Cr (VI) (citrate), Cr (VI) (humate). In all the treatments, pH level increased with time except for As (III), the removal of which was either without anions or in the presence of humate or nitrate.     

Biogeochemical cycling of ferric oxyhydroxide affecting As partition in groundwater aquitard

High arsenic (As) concentration in groundwater potentially poses a serious threat to the health of local residents in southwestern Taiwan. Although the As release to groundwater is responsible for the reducing bacteria-mediated reductive dissolution of As-rich Fe hydroxides, the influences of FeRB and different organic substrates on As and Fe mobility and transformation were rarely discussed. An experiment that involved As-adsorbed synthetic amorphous Fe(III) hydroxide (HFO) and the inoculation of in situ Fe-reducing bacteria (FeRB) was performed to evaluate the contribution of FeRB to the As mobility and transformation. The batched experiment of As-free HFO showed that the reducing bacteria rapidly induced the reduction of amorphous Fe oxyhydroxide to Fe(II) by reductive dissolution of HFO and formation of Fe-citrate complexation. For aqueous As(V) reduction experiment, arsenate was effectively reduced to As(III) by the facultative anaerobic bacterium in the cultured FeRB. In the experiment of As-containing HFO reduction, the aqueous As(V) acts as an electron acceptor and reduced to As(III) after the reductive dissolution of Fe(III) on HFO. However, the increase in the As(III) concentrations with time for various organic substrates in the As-adsorbed HFO-reducing experiment differ from the rates of As(V) reduction with various organic substrates in the As(V)-reducing experiment. The decrease in sorption sites by coupled reductive dissolution of HFO and the competitive desorption of small molecular organic carbon is apparently the important factor of As mobility. For large molecular organic carbon (i.e., citrate), the significant contribution of citrate on As mobility is the complexation of iron citrate. A working hypothesis model of As biogeochemical cycling is proposed to illustrate the relevant processes in the groundwater aquitard of southwestern Taiwan.     

集胞藻(Synechocystis sp. PCC6803)对砷吸收转化特性的初步研究

砷是一种广泛存在于环境中的有毒物质.集胞藻属于单细胞藻类,广泛分布在淡水生态环境中.采用营养液培养的方法探讨了集胞藻(Synechocystis sp.PCC6803)对砷的累积和转化特性.当集胞藻分别暴露于2和100 μM的无机As(Ⅲ)和As(Ⅴ)14 d后,体内的砷形态均以As(Ⅴ)为主,并且在100 μM浓度处...     

砷形态在湖水中垂直分布的研究

本文以天津水上公园湖泊作为研究现场，通过采样分析，研究了湖水中砷酸盐、亚砷酸盐、一甲基胂酸盐和二甲基胂酸盐的垂直分布及其影响因素。结果表明水上公园湖泊中砷酸盐是溶解态砷的主要存在形式，其垂直分布与悬浮物、叶绿素ａ、磷酸盐的浓度、水文等诸因素密切相关；一甲基胂酸盐含量保持相对稳定；光致转化是影响水中亚砷酸盐垂直分布差异的一个因素。     

Species-level study on arsenic availability from dietary components

Arsenic (As) contaminated water and foodstuffs are of major concern. Samples of drinking–cooking water (n = 50), raw rice (n = 50), common vegetables (eight types), and common pulses (three types) were collected from households in the endemic region. The study found up to 70% As reduction by using safe water for cooking of rice and vegetables. Speciation study reflected more arsenate than arsenite and other organic arsenicals in all the types of samples. Male intake of 293 μg As through drinking water contained 38 μg arsenite and 246 μg arsenate, and female intake of 199 μg As contained 167 μg arsenate and 25 μg arsenite. In cooked rice, 108 μg As contained 69 μg arsenate and 17 μg arsenite with 9 μg dimethylarsonic acid (DMA). Total As consumption from cooked vegetables was 45 μg with 34 and 4 μg of arsenite and arsenate, respectively, and 5 μg of DMA. Data indicate that cooking with As-free water removes arsenic in already contaminated foodstuffs but without interconversion of the As species, from toxic inorganic to less toxic organic forms.     

Non-carcinogenic effects of inorganic arsenic

This review will focus primarily on ohe effects of the inorganic arsenicals (arsenate and arsenite forms) that are present in drinking water. They are acutely toxic to both humans and animals, an effect that may be related to their bioavailibility. In humans, arsenicals have been reported to cause dermatitis and mucous membrane irritation upon exposure. They have also been reported to cause skin lesions and peripheral neurotoxicity in smelter workers and in patients treated with Fowler's Solution. When humans are exposed to arsenic in drinking water, effects such as hyperkeratosis, electromyographic abnormalities and vascular effects have been reported. In experimental animals, arsenic has been demonstrated to affect the liver and kidneys. In mice, arsenic has also been reported to decrease the animal's resistance to certain viral infections. The arsenite (+3) and arsenate (+5) forms have different modes of action. Arsenite binds to sulphhydryl groups and has been reported to inhibit over 100 different enzymes, while the arsenate can substitute for phosphate in various high energy intermediates, resulting in arsenolysis. In addition, when arsenate is reduced to arsenite in the body, it can also cause toxicity as that species.     

Nexus between polymer support and metal oxide nanoparticles in hybrid nanosorbent materials (HNMs) for sorption/desorption of target ligands

Metal oxide nanoparticles like hydrated ferric oxide (HFO) or hydrated zirconium oxide (HZrO) are excellent sorbents for environmentally significant ligands like phosphate, arsenic, or fluoride, present at trace concentrations. Since the sorption capacity is surface dependent for HFO and HZrO, nanoscale sizes offer significant enhancement in performance. However, due to their miniscule sizes, low attrition resistance, and poor durability they are unable to be used in typical plug-flow column setups. Meanwhile ion exchange resins, which have no specific affinity toward anionic ligands, are durable and chemically stable. By impregnating metal oxide nanoparticles inside a polymer support, with or without functional groups, a hybrid nanosorbent material (HNM) can be prepared. A HNM is durable, mechanically strong, and chemically stable. The functional groups of the polymeric support will affect the overall removal efficiency of the ligands exerted by the Donnan Membrane Effect. For example, the removal of arsenic by HFO or the removal of fluoride by HZrO is enhanced by using anion exchange resins. The HNM can be precisely tuned to remove one type of contaminant over another type. Also, the physical morphology of the support material, spherical bead versus ion exchange fiber, has a significant effect on kinetics of sorption and desorption. HNMs also possess dual sorption sites and are capable of removing multiple contaminants, namely, arsenate and perchlorate, concurrently.     

渍水土壤中硒迁移行为的研究

用土柱模拟4种加硒处理的土壤还原淋溶过程，研究了硒在土壤中的迁移和积累。结果表明，未加硒处理（土壤背景硒）的溶液中硒的迁移以有机硒占优势，Se(Ⅵ）及Se（Ⅳ）占的比例很小；土壤富野酸硒由上层向下层迁移。外源蛋白硒的处理的溶液中硒迁移为有机硒，部分外源硒以富里酸硒积累在下层土壤。外源Se(Ⅵ）和Se（Ⅳ）处理的溶液中硒迁移量只占加入量的0．2％和0．4％，硒迁移的主要形态前者为有机硒，后者为Se(Ⅳ）和有机硒；外源Se（Ⅵ）和Se(Ⅳ）的绝大部分以富里酸硒的形态积累于土壤，其积累量Se（Ⅵ）处理高于Se(Ⅳ）处理，上层土壤高于下层土壤。     

Characteristics of arsenic accumulation by the seaweeds Fucus spiralis and Ascophyllum nodosum

This study examines the accumulation of ⁷⁴As-arsenic in the seaweeds Fucus spiralis (L.) and Ascophyllum nodosum (L.) collected from Restronguet Creek in southwest England during 1978. Also, the influence of environmental factors (valence state of arsenic, pH, salinity, temperature, phosphate concentration) and metabolic inhibitors on the uptake of arsenic by F. spiralis is examined. Most of the arsenic in the seaweeds was non-exchangeable with labelled arsenic in the medium. The accumulation of ⁷⁴As reached a steady state in 1 to 8 d, depending on the species and external arsenic concentration. At steady state the accumulated arsenic is proportional to external arsenate concentration. F. spiralis accumulated 4 times more arsenate than arsenite. The short-term uptake of arsenic increased in proportion to the external arsenic concentration up to a level of 1000 g l^-1; it then remained constant at higher levels of arsenic. Arsenic uptake increased in direct proportion to increasing temperature. Variation of pH or salinity had no effect on arsenic incorporation. The accumulation of arsenic occurred only in living tissue and was inhibited by KCN in a concentration-dependent manner. The uptake of arsenic by F. spiralis in the presence of photo-synthetic inhibitors (DCMU or CMU) or in the dark was greater than in the light controls. Thus, it was concluded that energy is required for arsenic uptake and this is derived from respiration rather than photosynthesis. There was no evidence for a common mechanism of phosphate and arsenate uptake by macroalgae, although high concentrations of phosphate (40 to 400 M) initially inhibited arsenate uptake.     

Cycling of selenite and selenate in marine phytoplankton

The marine phytoplankton Dunaliella tertiolecta, Cachonina niei, Thalassiosira nordenskioldii, Phaeodactylum tricornutum, and Chaetoceros sp. were incubated with a range of molar concentrations of sodium-selenite (Na₂-SeIVO₃) and sodium-selenate (Na₂-SeVIO₄) to examine further their role in metabolic cycling of selenium in ocean waters. At low selenium concentrations, approaching those found naturally in seawater (10^-10 to 10^-9 M), all species distinguished between selenite and selenate, and actively concentrated selenite from the incubating medium while only marginally accumulating selenate. At much higher concentrations (10^-8 to 10^-6 M), selenate was also taken up. At the highest concentration tested, i.e., 10^-5 M with C. niei, after an immediate rapid uptake in the first 24 h, the intracellular selenite and selenate levels dropped to about 35 to 50% of the initial peak values. These observations suggest an uptake mechanism in these algae which, at normal ambient concentrations of selenium (10^-9 M), preferentially selects selenite and excludes selenate. At much higher concentrations (10^-8 M), the mechanism becomes overloaded and both selenium species enter the cells. Intracellularly, selenite became associated primarily with protein and amino acid fractions, in approximately equal proportions, while only ca. 4% of total intracellular selenium was found in the lipid fraction. Trace amounts of selenate that entered the cells, mainly during the first minutes of exposure, also entered the protein and amino acid components, but over time were increasingly associated with the protein fraction only. At the end of a 10-d incubation of algal cells in selenite-spiked medium, less than 25% of total Se in the medium could in fact be identified analytically as selenite. This suggests the presence of a non-selenite metabolite, possibly released back into the medium from the algae.     

Toxicology of arsenic in fish and aquatic systems

Arsenic (As) is found in waters such as seawater, warm springs, groundwater, rivers, and lakes. In aquatic environments, As occurs as a mixture of arsenate and arsenite, with arsenate usually predominating. The unrestricted application of As pesticides, industrial activities, and mining operations has led to the global occurrence of soluble As above permissible levels of 0.010 mg/L. Continuous exposure of freshwater organisms including fish to low concentrations of As results in bioaccumulation, notably in liver and kidney. As a consequence As induces hyperglycemia, depletion of enzymatic activities, various acute and chronic toxicity, and immune system dysfunction. Here we review arsenic chemistry, the occurrence of arsenic in aquatic system, the transformation and metabolism of arsenic; arsenic bioaccumulation and bioconcentration; behavioral changes; and acute and other effects such as biochemical, immunotoxic, and cytogenotoxic effects on fish.     

Arsenic adsorption on lignocellulosic substrate loaded with ferric ion

We loaded a lignocellulosic substrate extracted from wheat bran with ferric ions. This new low-cost adsorbent was prepared for the adsorption and removal of arsenate and arsenite ions from aqueous systems. The loading process of Fe in this biomaterial was done by hydrolization of a ferric salt while an alkaline solution was added dropwise. The new material obtained has a high sensivity to arsenite and arsenate species. Here, we investigated the effect of contact time, pH, and Fe content on the adsorption of both arsenic ions on the new material. This adsorption was found to be highly pH-dependent, which can be explained on the basis of electrostatic interactions between ionic species in solution and the ≡FeOH surface groups. The maximum adsorption capacity of arsenite and arsenate species vary linearly with the amount of Fe loaded on the lignocellulosic substrate.     

Effects of the interactions between selenium and phosphorus on the growth and selenium accumulation in rice (Oryza sativa)

The solution culture, paddy soil culture and the simulation experiments in the laboratory were conducted to clarify the interactions between selenium and phosphorus, and its effects on the growth and selenium accumulation in rice. Results revealed that a suitable supply of selenium could promote rice growth and excessive selenium could injure rice plant, causing lower biomass, especially in the roots. The supply of selenite could enhance the selenium contents of rice shoots and roots in solution culture and in soil culture. The selenium concentrations in roots were much higher than those in shoots supplied with the same rates of selenium and phosphorus. The interaction between selenium and phosphorus was evident. When the phosphorus supply increased to meet the needs of plant growth, phosphorus could promote absorption and accumulation of selenium in the shoots. If the phosphorus supply was excessive, phosphorus could inhibit the accumulation of selenium in the shoots at the lower selenite level (2 micromol l(-1)), but could not at the higher selenite level (10 micromol l(-1)). With the supply of phosphate increased, the selenium concentrations in the roots decreased significantly at both selenite levels. The presence of phosphate could decrease Se sorption on the soil surface and increase the selenium concentration in the soil solution. The concentrations of selenium in shoots and roots supplied with 0.08 g kg(-1) phosphorus were lower than those with no phosphorus supplied. With the increase of phosphorus added to 0.4 g kg(-1), the selenium concentration in shoots and roots increased. The effect of phosphorus on the concentration was statistically significant at all three selenium levels.     

Some Preliminary Observations On Zinc and Cadmium Accumulative Capacity in Arum Italicum Mill

Pot and hydroponic trials as well as tests on samples collected in a mining area and in two different urban sites of Tuscany were carried out on Arum italicum Mill (Italian arum) plants. Zinc and cadmium contents were determined by differential pulse anodic stripping voltammetry (DPASV) in different organs of about 180 samples. After 65 days treatment, zinc and cadmium median contents in leaves of plants grown hydroponically in solutions containing both metals at different concentrations fell within the range of 281-2022 and 8.3-45.1 μg g^-1 (dry weight), respectively. Some Italian arum plants were also cultivated in pots in the presence or absence of malate or citrate in order to evaluate the role of these ligands in zinc and cadmium accumulation. Citrate enhanced cadmium uptake compared to malate.     

Some Preliminary Observations On Zinc and Cadmium Accumulative Capacity in Arum Italicum Mill

Pot and hydroponic trials as well as tests on samples collected in a mining area and in two different urban sites of Tuscany were carried out on Arum italicum Mill (Italian arum) plants. Zinc and cadmium contents were determined by differential pulse anodic stripping voltammetry (DPASV) in different organs of about 180 samples. After 65 days treatment, zinc and cadmium median contents in leaves of plants grown hydroponically in solutions containing both metals at different concentrations fell within the range of 281-2022 and 8.3-45.1 μg g^-1 (dry weight), respectively. Some Italian arum plants were also cultivated in pots in the presence or absence of malate or citrate in order to evaluate the role of these ligands in zinc and cadmium accumulation. Citrate enhanced cadmium uptake compared to malate.     

Arsenic metabolism in marine bacteria and yeast

Arsenic metabolism was studied for two marine microorganisms, a facultative anaerobic bacterium, Serratia marinorubra, and an obligately aerobic yeast, Rhodotorula rubra. Both were cultivated in media with (⁷⁴As) arsenate (As V), and the products of arsenate metabolism were determined qualitatively. Both the bacterium and the yeast produced arsenite (AS III) and methylarsonic acid [CH₃AsO(OH)₂]. In addition to the foregoing, only the yeast produced dimethylarsinic acid (CH₃)₂AsO(OH) and volatile alkylarsines. In contrast, the bacterium growing anaerobically with cobalamine as a cofactor did not synthesize gaseous forms of arsenic such as methylarsines. Neither organism synthesized arsoniumphospholipids such as those produced by marine phytoplankton or terrestrial fungi. The yeast did not accumulate arsenite, but instead transported some of it into the culture medium and methylated the remainder first to methylarsonic acid and then to dimethylarsinic acid. Finally, the latter compound was methylated further and volatile alkylarsines were formed. In contrast, the bacterium retained all products of arsenate metabolism intracellularly. Both the bacterium and the yeast, therefore, converted relatively toxic arsenate, the most abundant arsenic compound in seawater, to products that were presumably less toxic.     

The sorption of selenite from aqueous solutions by pyrite

Selenium (Se) is an essential trace nutrient for mammals; however, the range between deficit and toxic levels is narrow. In this study, the potential sorption of selenite onto pyrite particles from an aqueous solution was investigated. An intraparticle diffusion model was used to describe kinetic data of sorption, yielding diffusivity values of 5 × 10^?7 cm²/s. The Langmuir isotherm equation could be used to describe the experimental data. The fitting results indicated that b and {Se(IV)}_max have values of 0.37 L/mg and 3.49 mg/g, respectively. The sorption of selenite onto the surface of pyrite particles was dependent on a pH range of 2–12, and the quantity of sorption onto pyrite was negatively correlated with pH; that is, the amount of sorption onto pyrite increased with a decrease in pH. In addition, organic matter did not exert a significant effect on removal of selenite. With a reaction time greater than 1 week, sorption of selenite onto pyrite particles was found to partially reduce the amount of elemental Se.