Evaluation of modified clay coagulant for sewage treatment

The use of modified clays as coagulants for sewage treatment was investigated in this study. The raw clays were montmorillonites K10 and KSF, and were modified by polymeric Al or Fe and/or Al/Fe mixing polymeric species. The comparative performance of modified clays and aluminium sulphate and ferric sulphate were evaluated in terms of the removal of turbidity, suspended solids, UV(254)-abs, colour, and total and soluble CODs. The results demonstrated that after being modified with mixing polymeric Al/Fe species, two montmorillonite clays possess greater properties to remove the particles (as suspended solids) and organic pollutants (as COD and UV(254)-abs) from the sewage and to enhance the particle settling rate significantly.     

Comparison of modified montmorillonite adsorbents. Part I: Preparation,characterization and phenol adsorption

This study concerns with the development of modified montmorillonites as adsorbents for water treatment. Polymeric aluminium and iron intercalated forms of montmorillonites have been prepared in the absence and presence of an alkylammonium cationic surfactant (Hexdecyl-trimethyl-ammonium bromide, HDTMA). Montmorillonites intercalated with polymeric Al, Fe, Fe/Al (2:1 Fe to Al ratio in solution), possess large N2 Brunauer-Emmett-Teller (BET) surface areas. XRD data also shows trace amounts of illite and plagioclase within the clay materials. Montmorillonites intercalated with HDTMA, polymeric Fe/HDTMA, polymeric Al/HDTMA and polymeric Fe/Al/HDTMA (1:1 metal to surfactant molar ratio in solution) undergo some losses of N2 BET surface areas. Preliminary adsorption studies on phenol have shown that polymeric Al/HDTMA- and HDTMA-only-modified montmorillonites possess a good affinity for phenol, whereas the polymeric Al/Fe modified- and starting montmorillonites have little affinity for phenol adsorption.     

Preparation of a porous clay heterostructure and study of its adsorption capacity of phenol and chlorinated phenols from aqueous solutions.

A porous clay heterostructure (PCH) from a Mexican clay was prepared and characterized, and its aqueous phenol and dichlorophenols (DCPs) adsorption capacities were studied using a batch equilibrium technique. The PCH displayed a surface area of 305.5 m2/g, 37.2 A average porous diameter, and a basal space of 23.2 A. The adsorption capacity shown by the PCH for both phenol and DCPs from water (14.5 mg/g for phenol; 48.7 mg/g for 3,4-DCP; and 45.5 mg/g for 2,5-DCP) suggests that the PCH has both hydrophobic and hydrophilic characteristics, as a result of the presence of silanol and siloxane groups formed during the pillaring and calcination of the PCH. The values of maximal adsorption capacity for dichlorophenols were higher than those reported for aluminum pillared clays and some inorgano-organo clays and comparable with some ionic exchange resins.     

Adsorption of hydrogen sulfide on montmorillonites modified with iron

Sodium-rich montmorillonite was modified with iron in order to introduce active centers for hydrogen sulfide adsorption. In the first modification, interlayer sodium cations were exchanged with iron. In another modification, iron oxocations were introduced to the clay surface. The most elaborated modification was based on doping of iron within the interlayer space of aluminum-pillared clay. The modified clay samples were tested as hydrogen sulfide adsorbents. Iron-doped samples showed a significant improvement in the capacity for H2S removal, despite of a noticeable decrease in microporosity compared to the initial pillared clay. The smallest capacity was obtained for the clay modified with iron oxocations. Variations in adsorption capacity are likely due to differences in the chemistry of iron species, degree of their dispersion on the surface, and accessibility of small pores for H2S molecule. The results suggest that on the surface of iron-modified clay hydrogen sulfide reacts with Fe(+3) forming sulfides or it is catalytically oxidized to SO2 on iron (hydro)oxides. Subsequent oxidation may lead to sulfate formation.     

Electrochemical and FTIR studies of the mutual influence of lead(II) or iron(III) and phenol on their adsorption from aqueous acid solution by modified activated carbons

Cyclic voltammetry and spectral FTIR studies of the influence of activated carbon surface modification on the co-adsorption of metal cation (lead or iron) and phenol from aqueous acidic solution were carried out. The diversity in surface chemical structure was achieved by applying different procedures of inorganic matter removal and by modifying the carbon samples in various ways: heating under vacuum, aminoxidation in an ammonia-oxygen atmosphere, oxidation with concentrated nitric acid. The quantities of adsorbed metal ions (Pb(2+) or Fe(3+)) and phenol from solutions containing cation or phenol separately or in a mixture were determined. The adsorption capacity from acidic aqueous acidic solution depends on the chemical properties of the activated carbon surface (e.g., decrease in phenol adsorption with relative lower basicity of the adsorbent). The electrochemical parameters of electrodes made from the carbon samples were estimated, and some possible electrochemical reactions were determined from voltammograms recorded in acid electrolyte solution containing adsorbed species (separately or as a mixture). Relationships were found between metal ion adsorption and electrochemical behavior of Pb(2+)/Pb(4+) and Fe(3+)/Fe(2+) couples on the one hand, and the presence of phenol in the solutions tested and the influence of surface chemistry of the carbon electrodes on electrochemical processes on the other. The changes in adsorption capacity with respect to the adsorbates used and the changes in FTIR spectra of the carbons as a result of adsorption and/or coupling phenol molecules are discussed.     

有机粘土矿物对水中低浓度菲的吸附性能和机理

分别选用十六烷三甲基溴化铵(HDTMA-Br)、四甲基溴化铵(TMA-Br)、聚乙二醇(PEG)表面活性剂改性天然粘土矿物,研究其对水中低浓度多环芳烃类难降解有机物菲的吸附性能和机理,并讨论了有机粘土的用量对吸附菲的性能的影响,验证了有机粘土矿物吸附菲后的稳定性.3种有机粘土矿物对菲的吸附等温线均呈中凹型,表现为分配系数(Kp)逐渐增大,表明吸附是分配作用和溶剂化效应共同作用的结果.根据Kp及土样有机碳含量(foc)所得的经有机碳归一化的分配系数(Koc)基本为常数,远远高于天然土壤/沉积物的Koc.在相同实验条件下,3种有机粘土矿物中HDTMA改性粘土矿物对菲的吸附性能最强,PEG改性粘土矿物次之,TMA改性粘土矿物最差.     

Simultaneous sorption of lead and chlorobenzene by organobentonite

Clays or organoclays have been used as a barrier to prevent the transport of hazardous contaminants in landfills. However, clays are known to effectively sorb mostly inorganic contaminants, while organoclays are mainly used for organic contaminants. Since the organoclays are basically clay particles modified with cationic surfactants, there might exist an optimal coverage of cationic surfactant on the clay particles to sorb both inorganic and organic contaminants. In order to determine the optimal mass of cationic surfactants on the bentonites, sodium bentonites were treated with various ratios of hexadecyltrimethylammonium (HDTMA) to bentonites. Chlorobenzene and lead were selected as representative contaminants. When either chlorobenzene or lead exists as a single contaminant, chlorobenzene sorption increased with increasing HDTMA to bentonite ratios, and lead sorption decreased with increasing HDTMA to bentonite ratios. Sorption of chlorobenzene was a function of HDTMA coverage on the bentonites, while lead sorption was much more influenced by the initial lead concentration rather than the mass of HDTMA added to the bentonites.     

固定化改性蒙脱土对苯酚吸附性能的研究

利用十六烷基三甲基溴化铵对天然蒙脱土进行改性,并用聚乙烯醇对改性蒙脱土进行固定化处理,然后进行柱状吸附和振荡条件的吸附试验。研究结果表明,HDTMA改性蒙脱土固定化后能有效吸附苯酚,不同环境条件对苯酚的柱状吸附能力产生不同的影响。在pH4~8的范围内,固定化改性蒙脱土对苯酚的吸附效果无显著性差异,pH在10以上,其吸附能力明显下降;温度对吸附效果影响不大;进水苯酚浓度越高,改性蒙脱土对苯酚的吸附量越大,但出水苯酚浓度也高;苯酚的流速越小,吸附容量越高,吸附效果越好。     

Adsorption of arsenate on soils. Part 2: modeling the relationship between adsorption capacity and soil physiochemical properties using 16 Chinese soils

An attempt has been made to elucidate the effects of soil properties on arsenate adsorption by modeling the relationships between adsorption capacity and the properties of 16 Chinese soils. The model produced was validated against three Australian and three American soils. The results showed that nearly 93.8% of the variability in arsenate adsorption on the low-energy surface could be described by citrate-dithionite extractable Fe (Fe(CD)), clay content, organic matter content (OM) and dissolved organic carbon (DOC); nearly 87.6% of the variability in arsenate adsorption on the high-energy surface could be described by Fe(CD), DOC and total arsenic in soils. Fe(CD) exhibited the most important positive influence on arsenate adsorption. Oxalate extractable Al (Al(OX)), citrate-dithionite extractable Al (Al(CD)), extractable P and soil pH appeared relatively unimportant for adsorption of arsenate by soils.     

Examination of the influence of phenyltrimethylammonium chloride (PTMA) concentration on acetochlor adsorption by modified montmorillonite

The results presented in this paper show an impact of the concentration of the aromatic organic cation on the adsorption of acetochlor on the surface of the organic-modified montmorillonite. Natural montmorillonite from Bogovina (Boljevac municipality, Serbia) was used for organic modification in this experiment. Cation exchange capacity of this montmorillonite (86 mmol 100 g^?1 of clay) was determined using the methylene blue method. In pretreatment, montmorillonite was modified with NaCl. For the purpose of organic modification, three different concentrations of phenyltrimethylammonium chloride (PTMA) have been selected, based on calculated CEC value: 43 mmol 100 g^?1 of clay (0.5 CEC), 86 mmol 100 g^?1 of clay (1 CEC) and 129 mmol 100 g^?1 of clay (1.5 CEC). The changes in the properties of the inorganic and organic modified montmorillonite were examined using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and batch equilibrium method. Freundlich coefficients show higher uptake of the herbicide by montmorillonite modified with PTMA, compared to inorganic-modified montmorillonite. The results also indicate the influence of the organic cation concentration on the adsorption of the selected herbicide.     

改性膨润土对垃圾填埋场渗滤液吸附效果

通过制备不同组分改性膨润土,研究其对苯酚的吸附效果,结果表明,十六烷基三甲基溴化铵+十二烷基磺酸钠+硫酸铝-改性膨润土>十六烷基三甲基溴化铵+十二烷基磺酸钠-改性膨润土>十六烷基三甲基溴化铵-改性膨润土。通过改性膨润土对实际复杂组分渗滤液的吸附研究,结果表明,使用活性炭改性的膨润土吸附COD和NH4+-N最为理想,单位质量COD吸附量最高为26.8 mg/g,NH4+-N最高为3.92 mg/g,其中,COD最高去除率为77.3%,氨氮为28.9%;十六烷基三甲基溴化铵+十二烷基磺酸钠+硫酸铝-改性膨润土对COD和NH4+-N均有去除效果,两者对于渗滤液实际处理工程具有应用价值。     

Sorption of paraquat on clay components in Taiwan's oxisol

The sorption of herbicides in soils is mainly influenced by clay components. The objectives of this study were to evaluate the contribution of clay components on paraquat sorption. The surface soils (0-20 cm) of a Laopi pedon (Fine, mixed, Hyperthermic Typic Hapludox) were separated clays into whole (< 2.0 microm), coarse (0.2-2.0 microm), and fine (< 0.2 microm) fractions with the treatments of removals of organic matter (OM) and free Fe (Fed) oxides. Results indicated that sorption isotherm of paraquat was fitted by the nonlinear Freundlich equation with R2 values ranged in 0.79-0.96, respectively. The shape of paraquat adsorption isotherm on the fine fraction was H-type, but their shapes on the whole and coarse fractions were L-types. The fine clay fractions gave higher contribution on paraquat sorption than the coarse clay fractions identified by their K(f) values. Organic matter associated with fine clay fraction had high CEC contributing to relatively high affinity for paraquat. The DCB treatment created high-affinity sites for paraquat on the fine clay, but had little effect on paraquat sorption for the coarse clay. Chemisorption is the major mechanism for retention of paraquat on clay components, not ion exchange. However, the silicate clay had the highest affinity for paraquat and free Fe compound had the lowest.     

Fenuron sorption on homoionic natural and modified smectites

The adsorption isotherms of fenuron (1,1-dimethyl-3-phenylurea) on three smectites (SWy and SAz montmorillonites and SH hectorite) differing in their layer charge (SH相似文献   

有机改性成都粘土预处理垃圾渗滤液

以成都粘土为原料,十六烷基三甲基溴化铵(HDTMA)为改性剂制备有机改性土,并将其应用于垃圾渗滤液的预处理。采用单因素静态吸附实验,以粘土对垃圾渗滤液COD和氨氮的去除率作为考查指标,初步探究有机改性土预处理垃圾渗滤液的适宜条件;并对有机改性粘土及原土进行性能表征,初步分析其吸附机理。研究结果表明,有机土的处理效果明显优于原土,处理效果上比原土提高了1.6~2.3倍;有机土预处理垃圾渗滤液适宜条件为:投加量120 g/L、搅拌速度200 r/min、搅拌时间50 min、pH=7、静置时间为6 h。     

Concentrations of polychlorinated dibenzo-p-dioxins in processed ball clay from the United States

Processed ball clays commonly used by the ceramic art industry in the United States were collected from retail suppliers and analyzed for the presence and concentration of the 2,3,7,8-Cl substituted polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/PCDFs). The average PCDD toxic equivalent (TEQ) concentrations of these processed ball clays was approximately 800 pg/g (TEQ-WHO) with characteristic congener profiles and isomer distributions similar to patterns of previously analyzed raw and processed ball clays. The PCDF concentrations were below the average limit of detection (LOD) of 0.5 pg/g. Correlation analyses reveal no significant relationship between total organic carbon (TOC) and either individual, homologues, and total tetra-through octa-chlorinated PCDD congeners, or TEQ concentrations of the processed ball clays. The results are consistent with earlier studies on levels of PCDDs in ball clays. Data from earlier studies indicated that dioxins may be released to the environment during the processing of raw clay or the firing process used in commercial ceramic facilities. The presence of dioxin in the clays also raises concerns about potential occupational exposure for individuals involved in the mining/processing of ball clay, ceramics manufacturing and ceramic artwork.     

Adsorption of lead onto smectite from aqueous solution

The purpose of this research is to study the effect of a new method of adsorption using membrane filtration to determine the maximum amount of lead adsorbed by clay and investigate the behavior of the clay after adsorption of the said metal. Treatment of wastewater contaminated with heavy metals depends on the characteristics of the effluent, the amount of final discharge, the cost of treatment, and the compatibility of the treatment process. The process of adsorption of heavy metals by clays may be a simple, selective, and economically viable alternative to the conventional physical–chemical treatment. This is justified by the importance of the surface developed by this material, the presence of negative charges on the said surface, the possibility of ion exchange taking place, and its wide availability in nature. The removal of lead from wastewater was studied by using the adsorption technique and using clay as the adsorbent. A method was optimized for adsorption through a membrane approaching natural adsorption. This new method is simple, selective, and the lead adsorption time is about 3 days. The various properties of clay were determined. It was observed that the cation exchange capacity of the clay was 56 meq/100 g of hydrated clay for the raw sample and 82 meq/100 g for the purified sample. The total surface area determined by the methylene blue method was equal to 556 and 783 m²/g for the raw and purified samples, respectively. The adsorption kinetics depends on several parameters. The Pb(II) clay, obeys the Langmuir, Freundlich, and the Elovich adsorption isotherms with high regression coefficients. The use of this adsorbent notably decreases the cost of treatment. It was concluded that clay shows a strong adsorption capacity on Pb(II), the maximum interaction occurring with purified clay treated at high concentration of lead. It is proposed that this adsorption through a membrane be extended for the treatment of effluents containing other metals.     

煤气发生炉炉渣改性和吸附性能

以工业中生产煤气时产生的煤气炉炉渣为原料,采用手工分选法将炉渣中的炭及残渣分离,再采用酸碱浸渍方法对炉渣残渣进行改性,研究了改性后的炉渣残渣及炉渣中分离出的炭对溶液中苯酚的吸附性能。吸附实验结果表明,分离炭的吸附性能最好,其次为碱改性炉渣残渣和酸改性炉渣残渣,未改性炉渣残渣吸附性能最差。改性的炉渣残渣及分离炭对苯酚吸附过程符合二级吸附动力学模型。吸附等温线研究表明,改性炉渣残渣及分离炭对苯酚的吸附符合Lang-muir吸附等温式。     

Influence of the organic complex concentration on adsorption of herbicide in organic modified montmorillonite

This study was undertaken to determine the impact of the organic complex concentration on the adsorption of herbicide (acetochlor) at the surface of the organic modified montmorillonite. In this work, natural montmorillonite from Bogovina (Boljevac municipality, Serbia) was used for organic modification. Cation-exchange capacity of this montmorillonite was determined using a methylene blue method (86 mmol/100 g of clay). Montmorillonite has been modified first with NaCl and then with hexadecyltrimethylammonium bromide (HDTMA-bromide) organic complex. Saturation of cation exchange capacity (CEC) was 50%, 100%, and 150%. Changes in the properties of the inorganic and organic montmorillonite have been examined using the X-ray diffraction, Fourier transform infrared spectroscopy, and batch equilibrium method. Montmorillonite modified with HDTMA-bromide demonstrated higher uptake of the herbicide, compared to the inorganic montmorillonite. Comparing the values Freundlich coefficients in batch equilibrium method, it can be seen that the adsorption of acetochlor decreased in the series: 0.5 CEC HM > 1 CEC HM > 1.5 CEC HM > NaM.     

Removal and pre-concentration of phenolic species onto beta-cyclodextrin modified poly(hydroxyethylmethacrylate-ethyleneglycoldimethacrylate) microbeads

Poly(Hydroxyethylmethacrylate-Ethyleneglycoldimethacrylate), poly(HEMA-EGDMA), microbeads with 150-200 microm in size, was prepared by suspension polymerization. Beta-cyclodextrin was modified onto the polymeric microbeads using glutaraldahyde activation in an acidic medium at pH=2.5. FT-IR and TGA were used for the characterization of modified polymers and the determination of the nature of the interaction between phenolic compounds and the modified polymeric microbeads. Plain and beta-cyclodextrin modified microbeads were used in adsorption-desorption studies of phenolic species in single solution. Adsorption capacities of the phenolic species onto the plain microbeads were found to be 28.2, 17.0, 14.3, 9.8, and 1.92 mg/g polymer for o-chloro phenol, p-nitro phenol, p-chloro phenol, o-nitro phenol, and phenol, respectively. However, for beta-cyclodextrin modified microbeads, adsorption capacity of phenolic species was determined as 274, 365, 128, 182, and 87 mg/g for phenol, o-nitro phenol, p-nitro phenol, o-chloro phenol, and p-chloro phenol, respectively. Desorption ratio for the phenolic species was more than 90%, except for o-nitro phenol. Detection limits of the phenolic species were improved at least 500-fold for UV-Vis spectrophotometric detection, after the pre-concentration of all phenolic species used in this study. Adsorption time for the phenolic species onto beta-cyclodextrin-modified poly(HEMA-EGDMA) microbeads was found to be reasonable short (10-60 min) and suitable for the applications. Also, synthesized microbeads were useful for the repeated use for the removal and pre-concentration of phenolic species.