As(V) retention on soils and forest by-products and other waste materials

As(V) retention capacity is determined by means of adsorption/desorption trials performed for coarse and fine ground mussel shell, forest and vineyard soils with or without fine shell, pine wood ash, oak wood ash, pine sawdust and slate-processing fines. Pine ash shows the highest arsenic retention potential (with >97 % adsorption and ≤1 % desorption), followed by shell-amended forest soil (adsorption between 96 and 92 %), by un-amended forest soil (adsorption between 98 and 86 %) and by the amended vineyard soil (adsorption between 92 and 75 %). Sawdust is the material with the lowest arsenic retention capacity in most cases, with un-amended vineyard soil also showing poor results. In the case of oak ash, As(V) percentage adsorption becomes higher with increasing added arsenic concentrations, while this increase in added arsenic causes lower percentage adsorption in the case of slate fines. Regarding adsorption ability, As(V) adsorption data were fitted to Freundlich and Langmuir models, showing good fitting, with pine ash and shell-amended forest soil having the highest K _F values. In view of that, mussel shell amendment would be useful to increase arsenic retention on forest and vineyard soils, while pine ash could be used to retain arsenic even from wastewaters.     

Mobility of heavy metals from polluted sediments of a semi-enclosed basin: in situ benthic chamber experiments in Taranto’s Mar Piccolo (Ionian Sea,Southern Italy)

In situ benthic flux experiments were conducted at two stations in the Mar Piccolo of Taranto (Italy), one of the most industrialised and contaminated coastal areas of the Mediterranean. Sediments of the two stations are notably different in their trace metal content, with a station closer to a Navy harbour showing higher mean concentrations of almost all investigated metals (Al, As, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, V and Zn). Conversely, both stations are characterised by significant Hg contamination, compared to the local baseline. Results of a sequential extraction scheme on surface sediments suggest a relatively scarce mobility of the examined metals (Zn > Ni > Cr > As > Cu > Pb). A Hg-specific extraction procedure showed that most of the element (93.1 %) occurs in a fraction comprising Hg bound to Fe/Mn oxi-hydroxides. Reduction of these oxides may affect Hg remobilisation and redistribution. Porewater profiles of dissolved trace metals were quite similar in the two sites, although significant differences could be observed for Al, Cu, Fe and Hg. The highest diffusive fluxes were observed for As, Fe and Mn. Mobility rates of several trace elements (Al, As, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, V and Zn) were directly measured at the sediment–water interface. Results from benthic in situ incubation experiments showed increasing dissolved metal concentrations with time, resulting in higher fluxes for Cu, Fe, Hg, V and Zn in the most contaminated site. Conversely, fluxes of Mn, Ni and Pb were comparable between the two stations. The estimated flux of Hg (97 μg m^?2 day^?1) was the highest observed among similar experiments conducted in other highly contaminated Mediterranean coastal environments. Benthic fluxes could be partially explained by considering rates of organic matter remineralisation, dissolution of Fe/Mn oxy-hydroxides and metal speciation in sediments. Seasonal and spatial variation of biogeochemical parameters can influence metal remobilisation in the Mar Piccolo area. In particular, metals could be promptly remobilised as a consequence of oxygen depletion, posing a serious concern for the widespread fishing and mussel farming activities in the area.     

Potential risk assessment of heavy metals by consuming shellfish collected from Xiamen, China

Concentrations of Hg, Pb, Cd, and Cr in 240 shellfish including oyster, short-necked clam, razor clam, and mud clam collected from six administrative regions in Xiamen of China were measured. The daily intakes of heavy metals through the consumption of shellfish were estimated based on both of the metal concentrations in shellfish and the consuming amounts of shellfish. In addition, the target hazard quotients (THQ) were used to evaluate the potential risk of heavy metals in shellfish on human body. Results showed that the concentrations of heavy metals in shellfish ranged at the following sequence: Cr > Cd > Pb > Hg. The concentrations of Hg and Pb in most samples were below the limits (0.3 mg?kg^?1 for Hg and 0.5 mg?kg^?1 for Pb) of national standard (GB 18406.4-2001) set in China. About 57 % of samples were found to contain more than 0.1 mg?kg^?1 of Cd, in which the highest level was found in oyster from Xiangan with a value of 1.21 mg?kg^?1. The average concentrations of Cd in oyster and mud clam samples were 0.338 and 0.369 mg?kg^?1, respectively, which were significantly higher (p?<?0.05) than those in the samples of short-necked clam and razor clam. The highest concentration of Cr was found to present in short-necked clam from Jimei with a value of 10.4 mg?kg^?1, but a mean value of 1.95 mg?kg^?1 in all the shellfish was observed, and no significant difference was found among the different sampling regions. The calculated daily intakes of Hg, Pb, Cd, and Cr through consuming the shellfish were 0.005, 0.122, 0.137, and 1.20 μg?kg^?1 day^?1, respectively, which accounted for 2.19, 3.42, 13.7, and 40.1 % of the corresponding tolerable limits suggested by the Joint FAO/WHO Expert Committee on Food Additives. The THQ values of the four metals were far below 1 for most samples, except for those of Cd and Cr in the four shellfish species with the mean values of 0.132 and 0.385, respectively. The highest THQ values of Cd were observed in the species of oyster (0.719) and mud clam (0.568). But the high THQ values of Cr observed in all the four species were derived from the applied reference dose (RfD) data of Cr(VI) due to the unavailable RfD value of total Cr. The results indicate that the intakes of heavy metals by consuming shellfish collected from Xiamen of China do not present an appreciable hazard risk on human health, but attention should be paid to consuming those with relatively high THQ values, such as oyster, mud clam, and short-necked clam.     

Assessing heavy metal pollution in the surface soils of a region that had undergone three decades of intense industrialization and urbanization

Heavy metals in the surface soils from lands of six different use types in one of the world’s most densely populated regions, which is also a major global manufacturing base, were analyzed to assess the impact of urbanization and industrialization on soil pollution. A total of 227 surface soil samples were collected and analyzed for major heavy metals (As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, and Zn) by using microwave-assisted acid digestion and inductively coupled plasma–mass spectrometry (ICP-MS). Multivariate analysis combined with enrichment factors showed that surface soils from the region (>7.2?×?10⁴ km²) had mean Cd, Cu, Zn, and As concentrations that were over two times higher than the background values, with Cd, Cu, and Zn clearly contributed by anthropogenic sources. Soil pollution by Pb was more widespread than the other heavy metals, which was contributed mostly by anthropogenic sources. The results also indicate that Mn, Co, Fe, Cr, and Ni in the surface soils were primarily derived from lithogenic sources, while Hg and As contents in the surface soils were controlled by both natural and anthropogenic sources. The pollution level and potential ecological risk of the surface soils both decreased in the order of: urban areas?>?waste disposal/treatment sites?～?industrial areas?>?agricultural lands?～?forest lands?>?water source protection areas. These results indicate the significant need for the development of pollution prevention and reduction strategies to reduce heavy metal pollution for regions undergoing fast industrialization and urbanization.     

Neutralization/prevention of acid rock drainage using mixtures of alkaline by-products and sulfidic mine wastes

Backfilling of open pit with sulfidic waste rock followed by inundation is a common method for reducing sulfide oxidation after mine closure. This approach can be complemented by mixing the waste rock with alkaline materials from pulp and steel mills to increase the system’s neutralization potential. Leachates from 1 m³ tanks containing sulfide-rich (ca.30 wt %) waste rock formed under dry and water saturated conditions under laboratory conditions were characterized and compared to those formed from mixtures. The waste rock leachate produced an acidic leachate (pH?<?2) with high concentrations of As (65 mg/L), Cu (6 mg/L), and Zn (150 mg/L) after 258 days. The leachate from water-saturated waste rock had lower concentrations of As and Cu (<2 μg/L), Pb and Zn (20 μg/L and 5 mg/L), respectively, and its pH was around 6. Crushed (<6 mm) waste rock mixed with different fractions (1–5 wt %) of green liquid dregs, fly ash, mesa lime, and argon oxygen decarburization (AOD) slag was leached on a small scale for 65 day, and showed near-neutral pH values, except for mixtures of waste rock with AOD slag and fly ash (5 % w/w) which were more basic (pH?>?9). The decrease of elemental concentration in the leachate was most pronounced for Pb and Zn, while Al and S were relatively high. Overall, the results obtained were promising and suggest that alkaline by-products could be useful additives for minimizing ARD formation.     

Distribution of potentially toxic elements (PTEs) in tailings,soils, and plants around Gol-E-Gohar iron mine,a case study in Iran

This study investigated the concentration of potentially toxic elements (PTEs) including Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Sb, V, and Zn in 102 soils (in the Near and Far areas of the mine), 7 tailings, and 60 plant samples (shoots and roots of Artemisia sieberi and Zygophylum species) collected at the Gol-E-Gohar iron ore mine in Iran. The elemental concentrations in tailings and soil samples (in Near and Far areas) varied between 7.4 and 35.8 mg kg^?1 for As (with a mean of 25.39 mg kg^?1 for tailings), 7.9 and 261.5 mg kg^?1 (mean 189.83 mg kg^?1 for tailings) for Co, 17.7 and 885.03 mg kg^?1 (mean 472.77 mg kg^?1 for tailings) for Cu, 12,500 and 400,000 mg kg^?1 (mean 120,642.86 mg kg^?1 for tailings) for Fe, and 28.1 and 278.1 mg kg^?1 (mean 150.29 mg kg^?1 for tailings) for Ni. A number of physicochemical parameters and pollution index for soils were determined around the mine. Sequential extractions of tailings and soil samples indicated that Fe, Cr, and Co were the least mobile and that Mn, Zn, Cu, and As were potentially available for plants uptake. Similar to soil, the concentration of Al, As, Co, Cr, Cu, Fe, Mn, Mo, Ni, and Zn in plant samples decreased with the distance from the mining/processing areas. Data on plants showed that metal concentrations in shoots usually exceeded those in roots and varied significantly between the two investigated species (Artemisia sieberi > Zygophylum). All the reported results suggest that the soil and plants near the iron ore mine are contaminated with PTEs and that they can be potentially dispersed in the environment via aerosol transport and deposition.     

Effect of deposit age on adsorption and desorption behaviors of ammonia nitrogen on municipal solid waste

Ammonia nitrogen pollution control is an urgent issue of landfill. This research aims to select an optimal refuse for ammonia nitrogen removal in landfill from the point of view of adsorption and desorption behavior. MSW (municipal solid waste) samples which deposit ages were in the range of 5 to 15 years (named as R₁₅, R₁₁, R₇, and R₅) were collected from real landfill site. The ammonia nitrogen adsorption behaviors of MSW including equilibrium time, adsorption isotherms, and desorption behaviors including equilibrium time were determined. Furthermore, the effects of pH, OM, Cu(II), Zn(II), and Pb(II) on adsorption and desorption behavior of ammonia nitrogen were conducted by orthogonal experiment. The equilibrium time of ammonia nitrogen adsorption by each tested MSW was very short, i.e., 20 min, whereas desorption process needed 24 h and the ammonia nitrogen released from refuses was much lesser than that adsorbed, i.e., accounted for 3.20 % (R₁₅), 14.32 % (R₁₁), 20.59 % (R₇), and 20.50 % (R₅) of each adsorption quantity, respectively. The maximum adsorption capacity estimated from Langmuir isotherm appeared in R₁₅-KCl, i.e., 25,000 mg kg^?1. The best condition for ammonia nitrogen removal from leachate was pH >7.5, OM 23.58 %, Cu(II) <5 mg L^?1, Zn(II) <10 mg L^?1, and Pb(II) <1 mg L^?1. Ammonia nitrogen in landfill leachate could be quickly and largely absorbed by MSW but slowly and infrequently released. The refuse deposited for 15 years could be a suitable material for ammonia nitrogen removal.     

Polycyclic aromatic hydrocarbons and trace metals in mosque’s carpet dust of Riyadh,Saudi Arabia,and their health risk implications

The main objectives of this work were to identify and determine the concentrations of polycyclic aromatic hydrocarbons (PAHs) and trace metals in carpet dust samples from various mosques of the city of Riyadh and to assess the health risks associated with the exposure to these pollutants. Therefore, 31 samples of mosque’s carpet dust from Riyadh were collected. The results showed that 14 PAHs were present in the dust samples with concentrations ranged from 90 to 22,146 ng g^?1 (mean = 4096 ± 4277 ng g^?1) where low molecular weight compounds were dominant. The presence of PAHs were in the order of naphthalene > chrysene and benzo(b)fluoranthene > benzo(a)pyrene > acenaphthene and benzo(k)fluoranthene > pyrene and the absence of indeno(1,2,3-cd)pyrene and dibenz(a,h)anthracene. The diagnostic ratio coupled with principle component analysis (PCA) revealed mix sources of petrogenic from traffic, stack emission, and pyrogenic inputs from essence and perfumed wood burning. Trace metals were significant in the dust samples, and their concentrations decrease in the order of Zn, Mn, Cu, Cr, Pb, Ni, and V where Zn being the highest (94.4 ± 91.5 μg g^?1) and indium was the lowest (1.9 ± 9.3 μg g^?1). The trace metals were major in southern and central parts of Riyadh and followed the order of central Riyadh > southern Riyadh > western Riyadh > eastern Riyadh > northern Riyadh. Estimated risk based on the total PAHs was found to be 4.30 × 10^?11 for adult and 1.56 × 10^?11 for children. Elemental non-cancer risk for adults ranged from 7.9 × 10^?4 for Co to 7.58 × 10^?1 for Li and for children ranged from 3.70 × 10^?3 for Co to 3.54 for Li. Policy implication and mitigations of PAHs in Riyadh and Saudi Arabia were highlighted.     

Biosorption of chromium (VI) from aqueous solutions and ANN modelling

The use of sustainable, green and biodegradable natural wastes for Cr(VI) detoxification from the contaminated wastewater is considered as a challenging issue. The present research is aimed to assess the effectiveness of seven different natural biomaterials, such as jackfruit leaf, mango leaf, onion peel, garlic peel, bamboo leaf, acid treated rubber leaf and coconut shell powder, for Cr(VI) eradication from aqueous solution by biosorption process. Characterizations were conducted using SEM, BET and FTIR spectroscopy. The effects of operating parameters, viz., pH, initial Cr(VI) ion concentration, adsorbent dosages, contact time and temperature on metal removal efficiency, were studied. The biosorption mechanism was described by the pseudo-second-order model and Langmuir isotherm model. The biosorption process was exothermic, spontaneous and chemical (except garlic peel) in nature. The sequence of adsorption capacity was mango leaf > jackfruit leaf > acid treated rubber leaf > onion peel > bamboo leaf > garlic peel > coconut shell with maximum Langmuir adsorption capacity of 35.7 mg g^?1 for mango leaf. The treated effluent can be reused. Desorption study suggested effective reuse of the adsorbents up to three cycles, and safe disposal method of the used adsorbents suggested biodegradability and sustainability of the process by reapplication of the spent adsorbent and ultimately leading towards zero wastages. The performances of the adsorbents were verified with wastewater from electroplating industry. The scale-up study reported for industrial applications. ANN modelling using multilayer perception with gradient descent (GD) and Levenberg-Marquart (LM) algorithm had been successfully used for prediction of Cr(VI) removal efficiency. The study explores the undiscovered potential of the natural waste materials for sustainable existence of small and medium sector industries, especially in the third world countries by protecting the environment by eco-innovation.     

Field controlled experiments on the physiological responses of maize (Zea mays L.) leaves to low-level air and soil mercury exposures

Thousands of tons of mercury (Hg) are released from anthropogenic and natural sources to the atmosphere in a gaseous elemental form per year, yet little is known regarding the influence of airborne Hg on the physiological activities of plant leaves. In the present study, the effects of low-level air and soil Hg exposures on the gas exchange parameters of maize (Zea mays L.) leaves and their accumulation of Hg, proline, and malondialdehyde (MDA) were examined via field open-top chamber and Hg-enriched soil experiments, respectively. Low-level air Hg exposures (<50 ng m^?3) had little effects on the gas exchange parameters of maize leaves during most of the daytime (p?>?0.05). However, both the net photosynthesis rate and carboxylation efficiency of maize leaves exposed to 50 ng m^?3 air Hg were significantly lower than those exposed to 2 ng m^?3 air Hg in late morning (p?<?0.05). Additionally, the Hg, proline, and MDA concentrations in maize leaves exposed to 20 and 50 ng m^?3 air Hg were significantly higher than those exposed to 2 ng m^?3 air Hg (p?<?0.05). These results indicated that the increase in airborne Hg potentially damaged functional photosynthetic apparatus in plant leaves, inducing free proline accumulation and membrane lipid peroxidation. Due to minor translocation of soil Hg to the leaves, low-level soil Hg exposures (<1,000 ng g^?1) had no significant influences on the gas exchange parameters, or the Hg, proline, and MDA concentrations in maize leaves (p?>?0.05). Compared to soil Hg, airborne Hg easily caused physiological stress to plant leaves. The effects of increasing atmospheric Hg concentration on plant physiology should be of concern.     

Multivariate characterization of elements accumulated in Wolfiporia extensa mushroom from Yunnan province of China

ABSTRACT

Dried sclerotia of Wolfiporia extensa have been used as medicine in Asia from Eastern Han Dynasty, and also used as traditional snack called “fulingjiabing” in Beijing, China. In this paper, 18 macro and trace elements (Ag, As, Ba, Cd, Co, Cr, Cs, Cu, Fe, Li, Mn, Ni, Pb, Rb, Se, Sr, V, and Zn) in both flesh and peel of Wolfiporia extensa from seven sites of Yunnan province in China were determined by inductively coupled plasma mass spectrometer. The average recovery rates of certified reference materials for GBW10015 (spinach leaves) ranged from 90.5 to 113%, for GBW10028 (citrus leaves) from 92.8 to 106%, and for GBW07603 (bush branch and leaves) from 83.3 to 114.6%. Generally speaking, the concentration of all elements determined was at common level. The results of this survey indicate that mineral compositions in peel were higher than in flesh. In peel, the contents of investigated trace metals in mushroom samples were found to be in the range of 1,660–13,400 µg·g^?1 dry matter (dm) for Fe and 29.6–710 µg·g^?1 dm for Mn. The mean contents of Cr, Cu, Rb, V, and Zn in peel were between 10 and 20 µg·g^?1 dm, followed by As, Co, Li, Ni, Pb, Se, and Sr with mean contents between 1 and 10 µg·g^?1 dm, while Ag, Cd, and Cs had mean contents of <1 µg·g^?1 dm. In flesh, the concentration of Fe was in the range of 54–900 µg·g^?1 dm, and it was 1.5–49 µg·g^?1 dm for Mn, followed by Ba, Cu, Rb, and Zn in the range of 1 to 10 µg·g^?1 dm, while for Ag, As, Cd, Co, Cr, Cs, Li, Ni, Pb, Se, Sr, and V it was <1 µg·g^?1 dm. The concentration of toxic elements, such as As, Cd, and Pb, in both flesh and peel was below the permissible limits of World Health Organization. However, As and Pb contents in peel were higher than the limits permitted in the Chinese Pharmacopoeia. The results of principal component analysis showed that the flesh of Wolfiporia extensa from all the seven sites of the Yunnan province tend to cluster together, most probably because the origin of mineral elements in both flesh and peel is wood substrate (old and dead pine trees).     

Comparative and competitive adsorption of Cr(VI), As(III), and Ni(II) onto coconut charcoal

This study evaluates the behavior of coconut charcoal (AC) to adsorb Cr(VI), As(III), and Ni(II) in mono- and multicomponent (binary and ternary) systems. Batch experiments were carried out for mono- and multicomponent systems with varying metal ion concentrations to investigate the competitive adsorption characteristics. The adsorption kinetics followed the mechanism of the pseudo-second-order equation in both single and binary systems, indicating chemical sorption as the rate-limiting step of adsorption mechanism. Equilibrium studies showed that the adsorption of Cr(VI), As(III), and Ni(II) followed the Langmuir model and maximum adsorption capacities were found to be 5.257, 0.042, and 1.748 mg/g, respectively. In multicomponent system, As(III) and Ni(II) adsorption competed intensely, while Cr(VI) adsorption was much less affected by competition than As(III) and Ni(II). With the presence of Cr(VI), the adsorption capacities of As(III) and Ni(II) on AC were higher than those in single system and the metal sorption followed the order of Ni(II)?>?As(III)?>?Cr(VI). The results from the sequential adsorption–desorption cycles showed that AC adsorbent held good desorption and reusability.     

Competitive adsorption and desorption of arsenate,vanadate, and molybdate onto the low-cost adsorbent materials alum water treatment sludge and bauxite

When low-cost adsorbents are being used to remove contaminant ions (e.g. arsenate, vanadate, and molybdate) from wastewater, competitive adsorption/desorption are central processes determining their removal efficiency. Competitive adsorption of As, V, and Mo was investigated using equimolar oxyanion concentrations in single, binary, and tertiary combinations in adsorption isotherm and pH envelope studies while desorption of previously adsorbed oxyanions was examined in solutions containing single and binary oxyanion combinations. The low-cost adsorbent materials used were alum water treatment sludge (amorphous hydroxy-Al) and bauxite ore (crystalline Al oxides). Adsorption isotherm and pH envelope studies showed that Mo had only a small effect in decreasing adsorption of As and V but V and As had substantial and similar effects in reducing adsorption of the other. As had a greater effect than V in reducing adsorption of Mo and it was concluded that the affinity of oxyanions for the surfaces of water treatment sludge and bauxite followed the order As > V >> Mo. In 0.3 M NaCl electrolyte, desorption of previously adsorbed oxyanions amounted to 0.3–3.4% for V and As, and 11–20% for Mo. As had approximately four times greater effect than Mo in increasing desorption of V while V had about three times the effect of Mo in increasing desorption of As. Thus, the order of oxyanions in inducing desorption of the other oxyanions (i.e. As on V and As) was the same as that for adsorption selectivity: As > V >> Mo. Water treatment sludge was a more effective adsorbent than bauxite because it had a greater adsorption capacity for all three anions and, in addition, they were held more strongly so desorption in the background electrolyte was proportionately less. It was concluded that at similar molar concentrations, arsenate would tend to reduce adsorption of vanadate as well as displace vanadate already held on adsorbent surfaces while both anions will compete effectively with molybdate. The limiting factor for simultaneous removal of As, V, and Mo from multielement solutions by adsorption will therefore be the removal of Mo.     

The linear accumulation of atmospheric mercury by vegetable and grass leaves: Potential biomonitors for atmospheric mercury pollution

One question in the use of plants as biomonitors for atmospheric mercury (Hg) is to confirm the linear relationships of Hg concentrations between air and leaves. To explore the origin of Hg in the vegetable and grass leaves, open top chambers (OTCs) experiment was conducted to study the relationships of Hg concentrations between air and leaves of lettuce (Lactuca sativa L.), radish (Raphanus sativus L.), alfalfa (Medicago sativa L.) and ryegrass (Lolium perenne L.). The influence of Hg in soil on Hg accumulation in leaves was studied simultaneously by soil Hg-enriched experiment. Hg concentrations in grass and vegetable leaves and roots were measured in both experiments. Results from OTCs experiment showed that Hg concentrations in leaves of the four species were significantly positively correlated with those in air during the growth time (p?<?0.05), while results from soil Hg-enriched experiment indicated that soil-borne Hg had significant influence on Hg accumulation in the roots of each plant (p?<?0.05), and some influence on vegetable leaves (p?<?0.05), but no significant influence on Hg accumulation in grass leaves (p?>?0.05). Thus, Hg in grass leaves is mainly originated from the atmosphere, and grass leaves are more suitable as potential biomonitors for atmospheric Hg pollution. The effect detection limits (EDLs) for the leaves of alfalfa and ryegrass were 15.1 and 22.2 ng g^–1, respectively, and the biological detection limit (BDL) for alfalfa and ryegrass was 3.4 ng m^–3.     

Changes in speciation and leaching behaviors of heavy metals in dredged sediment solidified/stabilized with various materials

Solidification/stabilization (S/S) of sediments is frequently used to treat contaminants in dredged sediments. In this study, sediment collected from the Pearl River Delta (China) was solidified/stabilized with three different kinds of functional materials: cement, lime and bentonite. Lime primarily acted via induced increases in pH, while cements stabilization occurred through their silicate-based systems and the main function of bentonite was adsorption. The speciation and leaching behaviors of specific heavy metals before and after S/S were analyzed and the results showed that the residual speciation of Cd, Cr, Ni, Pb and Zn increased in all treatments except for Cu, as the exchangeable speciation, carbonate-bound speciation and Fe-Mn-oxide-bound speciation of Cu (all of which could be stabilized) were less than 2 % of the total amount. Pb leaching only decreased when pH increased, while the mobility of Cr and Ni only decreased in response to the silicate-based systems. The leached portion of the Fe-Mn-oxide-bound speciation followed the order Zn?>?Cu?>?Ni/Cd?>?Pb?>?Cr. The leached portion of organic-matter-bound species was less than 4 % for Cd, Cr, Ni and Pb, but 35.1 % and 20.6 % for Cu and Zn, respectively.     

Source profile and health risk assessment of PM2.5 from coal-fired power plants in Fuxin,China

In order to improve and establish the localized source profile of PM_2.5 in Fuxin, the ashes under dust catcher were collected from four typical coal-fired power plants in Fuxin and twenty-eight components were measured. The source profile of PM_2.5 in the soot of the four coal-fired power plants was established. SO₄^2? was the most abundant component in the PM_2.5 of the soot of the four coal-fired power plants, followed by Ca²⁺ and organic carbon (OC). The content of element components in PM_2.5 smoke ranges from 5.06 to 10.97%, the content of ionic components ranges from 36.53 to 48.59%, and the total carbon content ranges from 9.43 to 11.36%. The divergence coefficient of PM_2.5 source profile in Fuxin coal burning smoke is mostly similar to that of Fushun, whereas the divergence coefficient of Colorado reaches 0.65, indicating that Fuxin coal burning power plant smoke has no similarity to Colorado. The order of the geological accumulation index of Ni, Cu, V, Mn, and Cr was Cr (4.58) > Mn (4.42) > V (4.38) > Cu (4.09) > Ni (4.06), showing a heavy pollution level. The health risk assessment model recommended by the USEPA was used to assess the health risk of heavy metals in soot of coal-fired power plants, and the non-carcinogenic risk values of As for children and adults were 45.7 and 4.90, respectively. The carcinogenic risk values of Cr for adults and children were the highest, with values of 3.66 × 10^?5 and 2.06 × 10^?5, respectively, followed by As.

     

Development of an in vitro toxicological test system based on zebrafish (<Emphasis Type="Italic">Danio rerio</Emphasis>) sperm analysis

The effect of seven heavy metals on the motility parameter of zebrafish sperm was tested in order to develop an in vitro toxicological test system as an alternative to live animal testing. In vitro test systems are currently preferred in ecotoxicology due to their practical and ethical advantages and fish sperm can be a suitable model. A number of studies had been carried out previously on this topic, but the described methods had not been standardized in numerous aspects (donor species, measured endpoint, etc.). In this study, heavy metals (mercury, arsenic, chromium, zinc, nickel, copper, cadmium) were used as reference toxicants with known toxicity to develop a standardized fish sperm in vitro assay. The tested concentrations were determined based on preliminary range finding tests. The endpoints were progressive motility (PMOT, %), curvilinear velocity (VCL, μm/s), and linearity (LIN, %) measured by a computer-assisted sperm analysis (CASA) system. According to our results, PMOT was the most sensitive of the three investigated parameters: dose-response curves were observed for each metal at relatively low concentrations. VCL values were less sensitive: higher concentrations were needed to observe changes. Of the three parameters, LIN was the least affected: dose-response relationship was observed only in the case of mercury (e.g., lowest observed effect concentration (LOEC) of Hg at 120 min: 1 mg/L for PMOT, 2.5 mg/L for VCL, 5 mg/L for LIN; LOEC of Cu at 120 min: 1 mg/L for PMOT, 5 mg/L for VCL, any for LIN). The order of toxicity as determined by PMOT was as follows: Hg²⁺?>?As³⁺?>?Cd²⁺?>?Cu²⁺?>?Zn²⁺?>?Cr³⁺?>?Ni²⁺. In conclusion, we found that PMOT of zebrafish sperm was an accurate and fast bioindicator of heavy metal load. Sperm analysis can be adopted to estimate the possible toxic effects of various chemicals in vitro. Future investigations should concentrate on the applicability of this assay to other contaminants (e.g., organic pollutants).     

Distribution coefficients of potentially toxic elements in soils from the eastern Amazon

The solid-solution distribution or partition coefficient (Kd) is a measure of affinity of potentially toxic elements (PTE) for soil colloids. Kd plays a key role in several models for defining PTE guideline values in soils and for assessing environmental risks, and its value depends on edaphic and climatic conditions of the sites where the soils occur. This study quantified Kd values for Cd, Co, Cr, Cu, Hg, Ni, Pb, and Zn from representative soil samples from Brazil’s eastern Amazon region, which measures 1.2 million km². The Kd values obtained were lower than those set by both international and Brazilian environmental agencies and were correlated with the pH, Fe and Mn oxide content, and cationic exchange capacity of the soils. The following order of decreasing affinity was observed: Pb?>?Cu?>?Hg?>?Cr?>?Cd?≈?Co?>?Ni?>?Zn.     

Purification of industrial phosphoric acid (54 %) using Fe-pillared bentonite

The current problem of excess impurities in industrial phosphoric acid (IPA) 54 % P₂O₅ makes phosphates industries look toward low-cost but efficient adsorbents. In the present study, iron-oxide-modified bentonite (Fe-PILB) was prepared and investigated as a possible adsorbent for the removal of organic matter (OM) like humic acid (HA), chromium (Cr(III)), and zinc (Zn(II)) from IPA aqueous solutions. These adsorbents were characterized using XRD, TEM, and BET. The adsorption of impurities is well described by the pseudo-second-order model. The results indicate that Fe-PILB has a good ability to resist co-existing anions and the low-pH condition of IPA and owns a relatively high-removal capacity of 80.42 and 25 % for OM, Cr(III), and Zn(II). The mechanism of adsorption may be described by the ligand and ion exchange that happened on the active sites. The selected order of adsorption OM?>?Cr³⁺?>?Zn²⁺ showed the importance of the competitive phenomenon onto bentonite materials’ pore adsorption. For the adsorption of OM at the low pH of IPA, H-bond complexation was the dominant mechanism. From the adsorption of heavy metals and OM complex compounds contained in IPA 54 % on Fe-PILB, the bridging of humic acid between bentonite and heavy metals (Zn(II) or Cr(III)) is proposed as the dominant adsorption mechanism (bentonite-HA-Me). Overall, the results obtained in this study indicate Fe-pillared bentonite possesses a potential for the practical application of impurity (OM, Zn(II), and Cr(III)) removal from IPA aqueous solutions.     

The characteristics of nitrate removal by the psychrotolerant denitrifying bacterium Acinetobacter johnonii DBP-3, isolated from a low-temperature eutrophic body of water

A psychrotolerant denitrifying bacterial strain, DBP-3, was isolated from a eutrophic body of water by low-temperature-oriented acclimation culture. Based on its morphologicalandbiochemicalcharacteristics and 16S rDNA gene sequence, the bacterium was identified as belonging to the genus Acinetobacter and closely related to A. johnonii. The satisfactory growth of DBP-3 was observed at 10–30°C and pH 7–9. Strain DBP-3 was able to utilize three types of carbon sources (sodium acetate > sodium citrate > glucose) to support growth and denitrification. DBP-3 grew faster, but with lower nitrate removal efficiency and higher nitrite accumulation, under aerobic conditions than under anoxic conditions. DBP-3 was extremely susceptible to tetracycline and rifampicine and less sensitive to ampicillin and penicillin. The growth of DBP-3 was significantly affected by Hg (II), Cr (VI), Pb (II), Cd (II), and As (III) at 0.32, 0.63, 1.25, 2.5, and 25.0 mg L^?1, respectively. Interestingly, chromium (VI) significantly promoted DBP-3 growth at concentrations lower than 0.32 mg L^?1. These data may be helpful to support the use of strain DBP-3 in the purification of eutrophic water bodies at low temperatures.