Particulates and Metallic Elements Monitoring at Two Sampling Sites (Harbor,Airport) in Taiwan

This study characterized the dry deposition flux and dry deposition velocity (Vd) of metallic elements attached on particulate matter. Specifically, large particles (>10 μm), coarse particles (10 μm～2.5 μm), and fine particles (<2.5 μm) were studied at the Gong Ming Junior High School (Taichung Airport) and Taichung Harbor sampling sites in central Taiwan. Ambient air samples were collected to determine total suspended particulate matter (TSP), dry deposition plate (DDP), Vd, coarse particulate matter (PM_2.5–10) and fine particulate matter (PM_2.5), and metallic elements concentrations at the Airport and Taichung Harbor sites between June 17, 2013, and November 14, 2013. The results revealed that the average TSP, DDP, Vd, PM_2.5–10, and PM_2.5 particulate at the Airport were 54.55 (μg/m³), 902.25 (μg/m²-min), 17.11 (m/sec), 0.003 (μg/m³), and 0.010 (μg/m³), respectively; while these values at Taichung Harbor were 63.66 (μg/m³), 539.69 (μg/m²-min), 9.94 (m/sec), 0.003 (μg/m³), and 0.014 (μg/m³), respectively. In addition, the results showed that the average Cu and Pb concentrations were higher than Cr, Ni, and Cd for both the airport and harbor sampling sites. Furthermore, Cr, N, Cu, Cd, and Pb had the highest average concentrations versus those reported for other study areas, with one exception: The results obtained in Kacanik, Kosovo, during 2005. The average metallic elements concentrations order was Cu > Pb > Cr > Ni > Cd.     

Short-term effects of atmospheric particulate matter on myocardial infarction: a cumulative meta-analysis

Atmospheric particulate matter (PM) is hypothesized to increase the risk of myocardial infarction (MI). However, the epidemiological evidence is inconsistent. We identified 33 studies with more than 4 million MI patients and applied meta-analysis and meta-regression to assess the available evidence. Twenty-five studies presented the effects of the PM level on hospitalization for MI patients, while eight studies showed the effects on mortality. An increase in PM₁₀ was associated with hospitalization and mortality in myocardial infarction patients (RR per 10 μg/m³?=?1.011, 95 % CI 1.006–1.016; RR per 10 μg/m³?=?1.008, 95 % CI 1.004–1.012, respectively); PM_2.5 also increased the risk of hospitalization and mortality in MI patients (RR per 10 μg/m³?=?1.024, 95 % CI 1.007–1.041 for hospitalization and RR per 10 μg/m³?=?1.012, 95 % CI 1.010–1.015 for mortality). The results of the cumulative meta-analysis indicated that PM₁₀ and PM_2.5 were associated with myocardial infarctionwith the addition of new studies each year. In conclusion, short-term exposure to high PM₁₀ and PM_2.5 levels revealed to increase risk of hospitalization and mortality for myocardial infarction. Policy support of pollution control and individual protection was strongly recommended.     

Comparisons of ambient air particulates concentrations (TSP,PM2.5) and dry depositions during smog and non-smog periods at Luliao,Shalu District sampling site

The concentrations of ambient total suspended particulates (TSP) and PM_2.5, and the dry depositions at a sample site at Luliao Junior High School (Luliao) in central Taiwan were measured during smog and non-smog days between December 2017 and July 2018. The results are compared to those obtained during non-smog periods in the years 2015–2017. The mean TSP and PM_2.5 concentrations and dry deposition flux were 72.41?±?26.40, 41.88?±?23.51?μg/m³, and 797.57?±?731.46?μg/m² min, respectively, on the smog days. The mean TSP and PM_2.5 concentrations and dry deposition flux on the non-smog days were 56.39?±?18.08, 34.81?±?12.59?μg/m³ and 468.93?±?600.57?μg/m² min, respectively. The mean TSP concentration in the smog period was 28% greater than that in the non-smog period, and the mean PM_2.5 concentration was 20% higher. The mean dry deposition flux in the smog period was 70% higher than that in the non-smog period at Luliao. The PM_2.5 concentrations exceeded the standards set by the Taiwan EPA (35?μg/m³ daily, and 15?μg/m³ annually). Therefore, the TSP and PM_2.5 concentrations and dry deposition must be reduced in central Taiwan on smog days. In addition, atmospheric TSP and PM_2.5 concentrations at various sampling sites were compared, and those herein were not higher than those measured in other countries. Finally, apart from the local traffic emissions, during smog periods, the other pollution source originated from the transportation process of traffic pollutants emitted in the northwest side of Taiwan.     

Atmospheric Particulate Matter and Polycyclic Aromatic Hydrocarbons for PM10 and Size-Segregated Samples in Bangkok

Abstract

Air samples of particulate matter (PM) with an aerodynamic diameter less than 10 µm (PM₁₀) were collected from six sites in Bangkok, Thailand, using high-volume air samplers. Daily samples were taken at intervals of 12 days from November 1999 to November 2000. Size-selected sampling using a multislit Andersen size-fractionated cascade impactor was undertaken at one site in central Bangkok to identify particulate size distribution. The annual average PM₁₀ concentration at all six sites exceeded the Thailand National Ambient Air Quality Standard (NAAQS) of 50 µg/m³. The daily PM₁₀ concentrations at heavy traffic roadside areas ranged between 30 and 160 µg/m³. The highest PM₁₀ level occurred during the winter period (November–February), which is the dry season. From our results, which are based on a 1-yr survey, it can be observed that the particulate concentrations are associated with traffic volumes and seasonal factors (temperature and rainfall). The relative importance of size fractions in contributing to PM load is presented and discussed. Twenty polycyclic aromatic hydro-carbons (PAHs) associated with PM have been identified and quantified. The summed PAHs based on the 20 species had an average concentration of 60 ng/m³. Benzo(e)pyrene, indeno(123cd)pyrene, and benzo(ghi)perylene were the major compounds with average concentrations of 8, 10, and 13 ng/m³, respectively. Results indicate that more than 97% of PAHs were found in the small particulate size range of <0.95 µm.     

Identification and source apportionment of polycyclic aromatic hydrocarbons in ambient air particulate matter of Riyadh, Saudi Arabia

In an effort to assess the occurrence and sources of polycyclic aromatic hydrocarbons (PAHs) in the ambient air of Riyadh, Saudi Arabia, PM₁₀ samples were collected during December 2010. Diagnostic PAH concentration ratios were used as a tool to identify and characterize the PAH sources. The results reflect high PM₁₀ and PAH concentrations (particulate matter (PM)?=?270–1,270 μg/m³). The corresponding average PAH concentrations were in the range of 18?±?8 to 1,003?±?597 ng/m³ and the total concentrations (total PAHs (TPAHs) of 17 compounds) varied from 1,383 to 13,470 ng/m³ with an average of 5,871?±?2,830 ng/m³. The detection and quantification limits were 1–3 and 1–10 ng/ml, respectively, with a recovery range of 42–80 %. The ratio of the sum of the concentrations of the nine major non-alkylated compounds to the total (CPAHs/TPAHs) was 0.87?±?0.10, and other ratios were determined to apportion the PM sources. The PAHs found are characteristic for emissions from traffic with diesel being a predominant source.     

Trends in arsenic levels in PM10 and PM2.5 aerosol fractions in an industrialized area

Arsenic is a toxic element that affects human health and is widely distributed in the environment. In the area of study, the main Spanish and second largest European industrial ceramic cluster, the main source of arsenic aerosol is related to the impurities in some boracic minerals used in the ceramic process. Epidemiological studies on cancer occurrence in Spain points out the study region as one with the greater risk of cancer. Concentrations of particulate matter and arsenic content in PM₁₀ and PM_2.5 were measured and characterized by ICP-MS in the area of study during the years 2005–2010. Concentrations of PM₁₀ and its arsenic content range from 27 to 46 μg/m³ and from 0.7 to 6 ng/m³ in the industrial area, respectively, and from 25 to 40 μg/m³ and from 0.7 to 2.8 ng/m³ in the urban area, respectively. Concentrations of PM_2.5 and its arsenic content range from 12 to 14 μg/m³ and from 0.5 to 1.4 ng/m³ in the urban background area, respectively. Most of the arsenic content is present in the fine fraction, with ratios of PM_2.5/PM₁₀ in the range of 0.65–0.87. PM₁₀, PM_2.5, and its arsenic content show a sharp decrease in recent years associated with the economic downturn, which severely hit the production of ceramic materials in the area under study. The sharp production decrease due to the economic crisis combined with several technological improvements in recent years such as substitution of boron, which contains As impurities as raw material, have reduced the concentrations of PM₁₀, PM_2.5, and As in air to an extent that currently meets the existing European regulations.     

The acute effects of fine particles on respiratory mortality and morbidity in Beijing, 2004–2009

Recent epidemiological and toxicological studies have shown associations between particulate matter and human health. However, the estimates of adverse health effects are inconsistent across many countries and areas. The stratification and interaction models were employed within the context of the generalized additive Poisson regression equation to examine the acute effects of fine particles on respiratory health and to explore the possible joint modification of temperature, humidity, and season in Beijing, China, for the period 2004–2009. The results revealed that the respiratory health damage threshold of the PM_2.5 concentration was mainly within the range of 20–60 μg/m³, and the adverse effect of excessively high PM_2.5 concentration maintained a stable level. In the most serious case, an increase of 10 μg/m³ PM_2.5 results in an elevation of 4.60 % (95 % CI 3.84–4.60 %) and 4.48 % (95 % CI 3.53–5.41 %) with a lag of 3 days, values far higher than the average level of 0.69 % (95 % CI 0.54–0.85 %) and 1.32 % (95 % CI 1.02–1.61 %) for respiratory mortality and morbidity, respectively. There were strong seasonal patterns of adverse effects with the seasonal variation of temperature and humidity. The growth rates of respiratory mortality and morbidity were highest in winter. And, they increased 1.4 and 1.8 times in winter, greater than in the full year as PM_2.5 increased 10 μg/m³.     

Seasonal variations of particle-associated nitrosamines by gas chromatography–mass spectrometry in the atmospheric environment of Zonguldak, Turkey

A gas chromatography–mass spectrometry method has been proposed for the determination of low-level mutagenic and carcinogenic nitrosamines in particulate matter. The method includes the collection of particulate matters (PM_2.5 and PM₁₀) using a dichotomous Partisol 2025 sampler and extraction of the compounds from aqueous solution with dichloromethane/2-propanol after sonication with a slightly basic water solution prior to their GC-MS analysis in electron impact mode. The obtained recoveries of nitrosamines ranged from 92.4 to 99.2 %, and the precision of this method, as indicated by the relative standard deviations, was within the range of 0.95–2.46?%. The detection limits obtained from calculations using the GC-MS results based on S/N?=?3 were found within the range from 4 to 22 pg/m³. The predominant nitrosamines determined in particulate matter were N-nitrosodimethylamine, N-nitrosodiethylamine, N-nitrosodibutylamine and N-nitrosomorpholine. Furthermore, N-mono- and dinitrosopiperazine and N-nitrosoethylbutylamine were also determined. N-dinitrosopiperazine was detected in PM_2.5 samples at the highest concentrations of up to 22.85 ng/m³ and in PM_2.5–10 samples at concentrations up to 7.60 ng/m³ in winter, whereas it was found in PM_2.5 samples up to 5.15 ng/m³ and in PM_2.5–10 samples up to 3.12 ng/m³ in summer. The total concentrations of nitrosamines were up to 161.4 ng/m³ in fine and 53.90 ng/m³ in coarse fractions in winter, whereas in summer were up to 35.24 and 12.60 ng/m³, respectively. The concentration levels of nitrosamines fluctuated significantly within a year, with higher means and peak concentrations in the winter compared to that in the summertime. The seasonal variations of particle-associated nitrosamine concentrations were investigated together with their relationships with meteorological parameters using Pearson’s correlation analysis in the winter and summer periods. Analysis of variance was used to determine which concentrations of nitrosamines were statistically different from one another and, together with meteorological parameters and discriminant analysis, was used to classify the particle samples by particle size according to seasons. The classification results of the particle samples in different seasons were very satisfactory, allowing 99.5 % of cases to be correctly grouped.     

Personal exposure to fine particulate matter concentrations in central business district of a tropical coastal city

In the present study, personal exposure to fine particulate matter (particulate matter with an aerodynamic diameter <2.5 μm [PM_2.5]) concentrations in an urban hotspot (central business district [CBD]) was investigated. The PM monitoring campaigns were carried out at an urban hotspot from June to October 2015. The personal exposure monitoring was performed during three different time periods, i.e., morning (8 a.m.?9 a.m.), afternoon (12.30 p.m.–1.30 p.m.), and evening (4 p.m.–5 p.m.), to cover both the peak and lean hour activities of the CBD. The median PM_2.5 concentrations were 38.1, 34.9, and 40.4 µg/m³ during the morning, afternoon, and evening hours on the weekends. During weekdays, the median PM_2.5 concentrations were 59.5, 29.6, and 36.6 µg/m³ in the morning, afternoon, and evening hours, respectively. It was observed that the combined effect of traffic emissions, complex land use, and micrometeorological conditions created localized air pollution hotspots. Furthermore, the total PM_2.5 lung dose levels for an exposure duration of 1 hr were 8.7 ± 5.7 and 12.3 ± 5.2 µg at CBD during weekends and weekdays, respectively, as compared with 2.5 ± 0.8 µg at the urban background (UB). This study emphasizes the need for mobile measurement for short-term personal exposure assessment complementing the fixed air quality monitoring.

Implications: Personal exposure monitoring at an urban hotspot indicated space and time variation in PM concentrations that is not captured by the fixed air quality monitoring networks. The short-term exposure to higher concentrations can have a significant impact on health that need to be considered for the health risk–based air quality management. The study emphasizes the need of hotspot-based monitoring complementing the already existing fixed air quality monitoring in urban areas. The personal exposure patterns at hotspots can provide additional insight into sustainable urban planning.     

Temporal variations of atmospheric aerosol in four European urban areas

Purpose

The concentrations of PM₁₀ mass, PM_2.5 mass and particle number were continuously measured for 18 months in urban background locations across Europe to determine the spatial and temporal variability of particulate matter.

Methods

Daily PM₁₀ and PM_2.5 samples were continuously collected from October 2002 to April 2004 in background areas in Helsinki, Athens, Amsterdam and Birmingham. Particle mass was determined using analytical microbalances with precision of 1 ??g. Pre- and post-reflectance measurements were taken using smoke-stain reflectometers. One-minute measurements of particle number were obtained using condensation particle counters.

Results

The 18-month mean PM₁₀ and PM_2.5 mass concentrations ranged from 15.4 ??g/m³ in Helsinki to 56.7 ??g/m³ in Athens and from 9.0 ??g/m³ in Helsinki to 25.0 ??g/m³ in Athens, respectively. Particle number concentrations ranged from 10,091 part/cm³ in Helsinki to 24,180 part/cm³ in Athens with highest levels being measured in winter. Fine particles accounted for more than 60% of PM₁₀ with the exception of Athens where PM_2.5 comprised 43% of PM₁₀. Higher PM mass and number concentrations were measured in winter as compared to summer in all urban areas at a significance level p?Conclusions Significant quantitative and qualitative differences for particle mass across the four urban areas in Europe were observed. These were due to strong local and regional characteristics of particulate pollution sources which contribute to the heterogeneity of health responses. In addition, these findings also bear on the ability of different countries to comply with existing directives and the effectiveness of mitigation policies.     

Elemental composition of PM10 and PM2.5 in urban environment in South Brazil

The purpose of the present study is to analyze the elemental composition and the concentrations of PM₁₀ and PM_2.5 in the Guaíba Hydrographic Basin with HV PM₁₀ and dichotomous samplers. Three sampling sites were selected: 8° Distrito, CEASA and Charqueadas. The sampling was conducted from October 2001 to December 2002. The mass concentrations of the samplers were evaluated, while the elemental concentrations of Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu and Zn were determined using the Particle-Induced X-ray Emission (PIXE) technique. Factor Analysis and Canonical Correlation Analysis were applied to the chemical and meteorological variables in order to identify the sources of particulate matter. Industrial activities such as steel plants, coal-fired power plants, hospital waste burning, vehicular emissions and soil were identified as the sources of the particulate matter. Concentration levels higher than the daily and the annual average air quality standards (150 and 50 μg m⁻³, respectively) set by the Brazilian legislation were not observed.     

Source Apportionment of Particulate Matter (PM10) and Indoor Dust in a University Building

A study on source apportionment of indoor dust and particulate matter (PM₁₀) composition was conducted in a university building by using chemometrics. The objective of this study was to investigate the potential sources of selected heavy metals and ionic species in PM₁₀ and indoor dust. PM₁₀ samples were collected using a low-volume sampler (LVS) and indoor dust was collected using a soft brush. Inductively coupled plasma spectrometry (ICP-MS) was used to determine the concentration of heavy metals, while the concentration of cations and anions was determined by atomic absorption spectrometer (AAS) and ion chromatography (IC), respectively. The concentration of PM₁₀ recorded in the building throughout the sampling period ranged from 20 ± 10 μgm^?3 to 80 ± 33 μgm^?3. The composition of heavy metals in PM₁₀ and indoor dust were dominated by zinc (Zn), followed by lead (Pb), copper (Cu), and cadmium (Cd). Principle component analysis (PCA) and multiple linear regression (MLR) showed that the main sources of pollutants in PM₁₀ came from indoor renovations (73.83%), vehicle emissions (16.38%), earth crust sources (9.68%), and other outdoor sources (0.11%). For indoor dust, the pollutant source was mainly earth crust. This study suggests that chemometrics can be used for forensic investigation to determine the possible sources of indoor contaminants within a public building.     

Metallic Element Composition of Particulate Matter During Day and Night Sampling at a Traffic Site

Day and night period sampling programs were carried out using a versatile air pollutant system to collect fine particulate matter (PM_2.5) and coarse particulate matter (PM_2.5–10) simultaneously at a traffic junction that is only 60 m from HungKuang University located in Central Taiwan. Therefore, HungKuang University is regarded as the traffic sampling site in this study. Similar measurements were carried out in a previous 2013 study by Fang and colleagues during October 2012 to November 2012. Determination of metallic element composition of fine and coarse particulates collected during the day and the night was accomplished with inductively coupled plasma atomic emission spectrometry (ICP-AES). The results indicated that there were no significant differences in composition of metallic elements Zn, Cu, Cr, Mn, Fe, Pb, and Cd in either coarse or fine particles for both day and night sampling periods. The statistical results indicated no significant differences for metallic elements in the PM_2.5–10 particulates for day and night sampling periods. Also, no significant differences were noted for metallic elements in the PM_2.5 particulates for day and night sampling periods at this traffic sampling site. The proposed reason is the limited sampling period employed in this study. Another potential reason is the presence of traffic that runs heavily both day and night being a major contributor to the ambient air metallic pollutants in this region.     

Physicochemical and toxicological characteristics of urban aerosols during a recent Indonesian biomass burning episode

Air particulate matter (PM) samples were collected in Singapore from 21 to 29 October 2010. During this time period, a severe regional smoke haze episode lasted for a few days (21–23 October). Physicochemical and toxicological characteristics of both haze and non-haze aerosols were evaluated. The average mass concentration of PM_2.5 (PM with aerodynamic diameter of ≤2.5 μm) increased by a factor of 4 during the smoke haze period (107.2 μg/m³) as compared to that during the non-smoke haze period (27.0 μg/m³). The PM_2.5 samples were analyzed for 16 priority polycyclic aromatic hydrocarbons (PAHs) listed by the United States Environmental Protection Agency and 10 transition metals. Out of the seven PAHs known as potential or suspected carcinogens, five were found in significantly higher levels in smoke haze aerosols as compared to those in the background air. Metal concentrations were also found to be higher in haze aerosols. Additionally, the toxicological profile of the PM_2.5 samples was evaluated using a human epithelial lung cell line (A549). Cell viability and death counts were measured after a direct exposure of PM_2.5 samples to A459 cells for a period of 48 h. The percentage of metabolically active cells decreased significantly following a direct exposure to PM samples collected during the haze period. To provide further insights into the toxicological characteristics of the aerosol particles, glutathione levels, as an indirect measure of oxidative stress and caspase-3/7 levels as a measure of apoptotic death, were also evaluated.     

Use of the Light Absorption Coefficient to Monitor Elemental Carbon and PM2.5—Example of Santiago de Chile

Abstract

The optical absorption coefficient, particulate matter with an aerodynamic diameter <2.5 μm, and elemental carbon (EC) have been measured simultaneously during winter and spring of 2000 in the western part of Santiago, Chile (Pudahuel district). The optical measurements were carried out with a low-cost instrument recently developed at the University of Santiago. From the data, a site-specific mass absorption coefficient of 4.45 ± 0.01 m²/g has been found for EC. In addition, a mass absorption coefficient of 1.02 ± 0.03 m²/g has been obtained for PM_2.5. These coefficients can be used during the colder months (May-August) to obtain EC concentration or PM_2.5 from a measurement of the light absorption coefficient (σ_a). The high correlation that has been found between these variables indicates that σ_a is a good indicator of the degree of contamination of urbanized areas.

The data also show an increase in PM_2.5 and EC concentration during winter and an increase in the ratio of EC to PM_2.5. When the EC/PM_2.5 ratio is calculated during rush hour (7:00 a.m.-11:00 a.m.) and during part of the night (9:00 p.m.-2:00 a.m.), it is found that the increase is caused by higher concentration levels of EC at night. These results suggest that the rise in the EC concentration is caused by emissions from heating and air mass transport of pollution from other parts of the city, while traffic contribution remains approximately constant.     

Study of aluminium distribution and speciation in atmospheric particles of different diameters in Nanjing,China

Aluminium (Al) is one of the trace inorganic metals present in atmospheric particles. Al speciation study is essential to better evaluate the mobility, availability, and persistence of trace Al and Al species in the atmosphere. This paper reports Al distribution and speciation in atmospheric particles with aerodynamic diameters >10.0, 10.0–2.5 and <2.5 μm in the urban area of Nanjing, China. Urban particles were collected with a high-volume sampling system equipped with a cascade impactor, which effectively separates the particulate matter into three size ranges. Particulate Al was fractionated into five different forms (insoluble, oxide, organic, carbonate, and exchangeable species) by the modified five-step Tessier's sequential extraction procedure. The main points are as follows: (1) The average levels of Al in PM_2.5, PM_2.5–10 and PM_>10 are 2.02±0.35, 3.04±0.43 and 6.32±0.76 μg m⁻³, respectively, with PM_2.5, PM_2.5–10 and PM_>10 constituting respectively, 17.8±3.1%, 26.7±3.8% and 55.5±6.7% of suspended particulate matter (SPM) mass (11.38 μg m⁻³). (2) The vertical profile of airborne Al in the above three size fractions has been estimated. A significant increase in airborne Al concentrations was found for PM_2.5, PM_2.5–10 and PM_>10 as the sampling height above the ground increased from 2.5 to 17.5 m; however, there was an obvious decrease in airborne Al concentrations between 17.5 and 40.0 m. The maximum mean of total Al in PM_2.5, PM_2.5–10 and PM_>10 occurred between 12.5 and 20.0 m above the ground. (3) The distribution of Al speciation was studied. It was found that the size distribution of airborne Al species followed the order: insoluble species>oxide species>organic species>carbonate species>exchangeable species.     

Bus,minibus, metro inter-comparison of commuters’ exposure to air pollution in Mexico City

Commuters’ exposure measurements were taken for PM_2.5, carbon monoxide (CO) and benzene in minibuses, buses and metro during morning and evening rush hours during January–March 2003 in Mexico City. For PM_2.5, the chemical composition was characterized. Total carbon was the most abundant species in fine particles (approximately 50%). Minibuses (49 μg m⁻³) and buses had similar concentrations of exposure for PM_2.5 (53 μg m⁻³). For CO and benzene the concentrations were higher in minibuses. Morning rush hour was the commuting period with the highest concentrations for minibuses and buses. Metro was the mode of transport with lower concentrations for all pollutants. Carbon monoxide concentrations were similar to those identified in a previous campaign in 2002 and approximately 3.5 times lower than those in a study conducted in 1991. Benzene was characterized systematically in the selected modes of transport. A strong association was observed between wind speed and pollutant concentrations in buses.     

Particulate matter and manganese exposures in Toronto,Canada

Methylcyclopentadienyl manganese tricarbonyl (MMT) is a manganese-based gasoline additive used to enhance automobile performance. MMT has been used in Canadian gasoline for about 20 yr. Because of the potential for increased levels of Mn in particulate matter resulting from automotive exhausts, a large-scale population-based exposure study (∼1000 participant periods) was conducted in Toronto, Canada, to estimate the distribution of 3-day average personal exposures to particulate matter (PM_2.5 and PM₁₀) and Mn. A stratified, three-stage, two-phase probability, longitudinal sample design of the metropolitan population was employed. Residential indoor and outdoor, and ambient levels (at a fixed site and on a roof) of PM_2.5, PM₁₀, and Mn were also measured. Supplementary data on traffic counts, meteorology, MMT levels in gasoline, personal occupations, and activities (e.g. amount of vehicular usage) were collected. Overall precision (%RSD) for analysis of duplicate co-located samples ranged from 2.5 to 5.0% for particulate matter and 3.1 to 5.5% for Mn. The detection limits were 1.47 and 3.45 μg m^-3 for the PM₁₀ and PM_2.5 fractions, respectively, and 5.50 and 1.83 ng m^-3 for Mn in PM₁₀ and PM_2.5, respectively. These low detection limits permitted the reporting of concentrations for >98% of the samples. For PM₁₀, the personal particulate matter levels (median 48.5 μg m^-3) were much higher than either indoor (23.1 μg m^-3) or outdoor levels (23.6 μg m^-3). The median levels for PM_2.5 for personal, indoor, and outdoor were 28.4, 15.4 and 13.2 μg m^-3, respectively. The correlation between PM_2.5 personal exposures and indoor concentrations was high (0.79), while correlations between personal and the outdoor, fixed site and roof site were low (0.16–0.27). Indoor Mn concentration distributions (in PM_2.5 and PM₁₀), unlike particulate matter, exhibited much lower and less variable levels that the corresponding outdoor data. The median personal exposure was 8.0 ng m^-3, compared with 4.7 and 8.6 ng m^-3, respectively, for the indoor and outdoor distributions. The highest correlations occurred for personal vs indoor data (0.56) and for outdoor vs roof site data (0.66), and vs fixed site data (0.56). The concentration of Mn in particulate matter, expressed in ppm (w/w), revealed that the fixed site was the highest, followed by the roof site, outdoor, indoor, and personal. The personal and indoor data showed a statistically significant correlation (0.68) while all other correlations between personal or indoor data and outdoor or fixed-site data were quite small. The low correlations of personal and indoor levels with outdoor levels suggest that different sources in the indoor and outdoor microenvironments produce particle matter with dissimilar composition. The correlation results indicate that neither the roof- nor fixed-site concentrations can adequately predict personal particulate matter or Mn exposures.     

PM10 source apportionment in a Swiss Alpine valley impacted by highway traffic

Although trans-Alpine highway traffic exhaust is one of the major sources of air pollution along the highway valleys of the Alpine regions, little is known about its contribution to residential exposure and impact on respiratory health. In this paper, source-specific contributions to particulate matter with an aerodynamic diameter?<?10 μm (PM₁₀) and their spatio-temporal distribution were determined for later use in a pediatric asthma panel study in an Alpine village. PM₁₀ sources were identified by positive matrix factorization using chemical trace elements, elemental, and organic carbon from daily PM₁₀ filters collected between November 2007 and June 2009 at seven locations within the village. Of the nine sources identified, four were directly road traffic-related: traffic exhaust, road dust, tire and brake wear, and road salt contributing 16 %, 8 %, 1 %, and 2 % to annual PM₁₀ concentrations, respectively. They showed a clear dependence with distance to highway. Additional contributions were identified from secondary particles (27 %), biomass burning (18 %), railway (11 %), and mineral dust including a local construction site (13 %). Comparing these source contributions with known source-specific biomarkers (e.g., levoglucosan, nitro-polycyclic aromatic hydrocarbons) showed high agreement with biomass burning, moderate with secondary particles (in winter), and lowest agreement with traffic exhaust.     

Nitrate Artifacts during PM25 Sampling in the South Coast Air Basin of California

ABSTRACT

In February 1993, the South Coast Air Basin (SCAB) was redesignated as a “serious” nonattainment area for PM10. To improve the understanding and characterization of fine particulate matter in the SCAB, the South Coast Air Quality Management District (SCAQMD) initiated a comprehensive PM₁₀ Technical Enhancement Program (PTEP). Using enhanced PTEP monitors (specially designed multichannel/multifilter samplers), a one-year fine particulate matter (PM) monitoring program was initiated in January 1995. As part of the special monitoring program, nitric acid, ammonia, and speciated PM₁₀ and PM_2.5 concentrations were measured at five locations in the SCAB (downtown Los Angeles, Anaheim, Diamond Bar, Fontana, and Rubidoux) and at one background station (San Nicolas Island). The PM2.5 data are the first spatially resolved speciated data collected in the SCAB on an annual basis. Within the SCAB, where nitrate is a major component of PM_2.5, nitrate losses have been documented. The spatial and temporal variations of the nitrate losses during PM_2.5 sampling and the uncertainties of the nitrate losses are discussed. Significant losses occur at a low mass range, between 10 and 50 ìg/m³. Significant gains occur at an even lower mass range of less than 30 ìg/m³. On an annual average basis, nitrate losses vary between 1.25 and 2.32 ìg/m³ and the SCAB-wide average value of nitrate loss is 1.8 ìg/m³ based on five PTEP stations in the SCAB. The maximum nitrate losses for each station vary from 6.4 ìg/m³ to 22.5 ìg/m ³. Theoretical prediction of the sampling efficiency of the nitrate during PM_2.5 sam - pling was compared with the PTEP data. In general, theoretical prediction was in good agreement with measured values.