Degree of phosphorus saturation thresholds in manure-amended soils of alberta

The risk of P losses from agricultural land to surface and ground water generally increases as the degree of soil P saturation increases. A single-point soil P sorption index (PSI) was validated with adsorption isotherm data for determination of the P sorption status of Alberta soils. Soil P thresholds (change points) were then examined for two agricultural soils after eight annual applications of different rates of cattle manure and for three agricultural soils after one application of different rates of cattle manure. Linear relationships were found between soil-test P (STP) levels up to 1000 mg kg(-1) and desorbed P in the five Alberta soils. Weak linear relationships were also found between STP and runoff dissolved reactive phosphorus (DRP) in three of these soils. Change points for the degree of P saturation (DPS) were detected in four of the five soils at 3 to 44% for water-extractable P (WEP) and at 11 to 51% for CaCl(2)-extractable P (CaCl(2)-P). Change points were not found for DPS or runoff DRP. Overall DPS thresholds for the five soils combined were 27% for WEP and 44% for CaCl(2)-P at a critical desorbable-P value of 1 mg L(-1). The corresponding STP levels (44 mg kg(-1) for WEP and 71 mg kg(-1) for CaCl(2)-P) are similar to agronomic thresholds for crops grown on Alberta soils. Soluble P losses in overland flow and leaching may be greater in soils with DPS values that exceed these thresholds than in soils with lower DPS values.     

Phosphorus saturation in spodosols impacted by manure

Significant amounts of phosphorus (P) accumulate in soils receiving animal manures that could eventually result in unacceptable concentrations of dissolved P loss through surface runoff or subsurface leaching. The degree of phosphorus saturation (DPS) relates a soil's extractable P to its P sorbing capacity, and is reportedly a predictor of the P likely to be mobilized from a system. A DPS value (DPS-1) was derived that expressed the percentage of Mehlich 1-extractable P to the sorbing capacity of a Spodosol (expressed as the sum of oxalate-extractable Fe and Al). Values of DPS-1 were determined in various horizons of soil in current and abandoned dairy systems in South Florida's Lake Okeechobee watershed to assess P release potential. Land use within the dairies was classified as highly impacted by cattle (intensive and holding), and minimally impacted by cattle (pasture, forage, or native) areas. The A and E horizon of soils in heavily manure-impacted intensive and holding areas for both active and abandoned dairies generally had higher DPS-1 values than the pasture, forage, and native area soils, which were minimally impacted by manure. Degree of P saturation was also calculated as a percentage of Mehlich 1-extractable P to the sum of Mehlich 1-extractable Fe and Al (DPS-2). Both DPS-1 and DPS-2 were shown to be significantly (P = 0.0001) related to water-extractable P for all soil horizons, suggesting that either index can be used as an indicator for P loss potential from a soil.     

Approximating phosphorus release from soils to surface runoff and subsurface drainage

Phosphorus application in excess of crop needs has increased the concentration of P in surface soil and runoff and led many states to develop P-based nutrient management strategies. However, insufficient data are available relating P in surface soil, surface runoff, and subsurface drainage to develop sound guidelines. Thus, we investigated P release from the surface (0-5 cm depth) of a Denbigh silt loam from Devon, U.K. (30-160 mg kg-1 Olsen P) and Alvin, Berks, Calvin, and Watson soils from Pennsylvania (10-763 mg kg-1 Mehlich-3 P) in relation to the concentration of P in surface runoff and subsurface drainage. A change point, where the slopes of two linear relationships between water- or CaCl2-extractable soil P and soil test phosphorus (STP) (Olsen or Mehlich-3) meet, was evident for the Denbigh at 33 to 36 mg kg-1 Olsen P, and the Alvin and Berks soils at 185 to 190 mg Mehlich-3 P kg-1. Similar change points were also observed when STP was related to the P concentration of surface runoff (185 mg kg-1) and subsurface drainage (193 mg kg-1). The use of water and CaCl2 extraction of surface soil is suggested to estimate surface runoff P (r2 of 0.92 for UK and 0.86 for PA soils) and subsurface drainage P (r2 of 0.82 for UK and 0.88 for PA soils), and to determine a change point in STP, which may be used in support of agricultural and environmental P management.     

Phosphorus leaching in relation to soil type and soil phosphorus content

Phosphorus losses from arable soils contribute to eutrophication of freshwater systems. In addition to losses through surface runoff, leaching has lately gained increased attention as an important P transport pathway. Increased P levels in arable soils have highlighted the necessity of establishing a relationship between actual P leaching and soil P levels. In this study, we measured leaching of total phosphorus (TP) and dissolved reactive phosphorus (DRP) during three years in undisturbed soil columns of five soils. The soils were collected at sites, established between 1957 and 1966, included in a long-term Swedish fertility experiment with four P fertilization levels at each site. Total P losses varied between 0.03 and 1.09 kg ha(-1) yr(-1), but no general correlation could be found between P concentrations and soil test P (Olsen P and phosphorus content in ammonium lactate extract [P-AL]) or P sorption indices (single-point phosphorus sorption index [PSI] and P sorption saturation) of the topsoil. Instead, water transport mechanism through the soil and subsoil properties seemed to be more important for P leaching than soil test P value in the topsoil. In one soil, where preferential flow was the dominant water transport pathway, water and P bypassed the high sorption capacity of the subsoil, resulting in high losses. On the other hand, P leaching from some soils was low in spite of high P applications due to high P sorption capacity in the subsoil. Therefore, site-specific factors may serve as indicators for P leaching losses, but a single, general indicator for all soil types was not found in this study.     

Environmental index for estimating the risk of phosphorus loss in calcareous soils of Manitoba

The degree of phosphorus saturation (DPS) has been used in evaluating the risk of P loss from soil to runoff. While techniques are available for calculating DPS for acid soils, no widely used technique exists for neutral to calcareous soils that are typical of the Northern Great Plains, including Manitoba (Canada) soils. This study aimed to develop techniques of calculating the DPS of neutral to alkaline soils. Four measures of soil labile P and ten indices of P sorption capacity were used to calculate the DPS of 115 Manitoba soils. The various DPS calculated were evaluated using water-extractable ((H2O)) P as an index of P susceptibility to runoff loss. The DPS obtained using Olsen-extractable ((Ols)) P and the Langmuir adsorption maximum (ES(max)) ranged from 0.5 to 31.9% while those obtained from P(Ols) and the single-point adsorption index (P(150)) ranged from 0.9 to 73.9%. Of all the DPS evaluated, those that included P(Ols) and Mehlich 3-extractable ((M3)) P as the numerator with either P(150) or ES(max) as the denominator were fairly well correlated with P(H2O) (r values ranged between 0.45 and 0.63). Along with ES(max) and P(150), a new method of calculating DPS was formulated as the ratio of P(Ols) or P(M3) to Ca(M3) or (Ca + Mg)(M3). We found that the ratio of ammonium oxalate-extractable ((ox)) P to (Al + Fe)(ox), which has been widely used to calculate DPS in acid soils, was not suitable for neutral to alkaline soils of Manitoba. In these neutral to alkaline soils, Ca(M3) or (Ca + Mg)(M3) were better indices of P sorption capacity while P(Ols) and P(M3) provided better estimates of labile soil P. The DPS calculated using Ca(M3) or (Ca + Mg)(M3) were well correlated with P(H2O); however, they were numerically smaller than those obtained from the Langmuir adsorption maximum. As such, a saturation coefficient (alpha) with a value of 0.2 was generated to improve the numerical values of the newly estimated DPS. This new approach can be used to estimate the DPS in neutral and calcareous soils without the need to generate a P adsorption maximum.     

Spatial analysis of phosphorus sorption capacity in a semiarid altered wetland

The observed increase in phosphorus (P) loading into the Jordan River could increase eutrophication processes in Lake Kinneret, the only freshwater lake in Israel, which provides 25% of the country's drinking water. The P may originate from the peat soils of the highly altered Hula Valley's semiarid wetland ecosystem through which the Jordan River runs. The objectives of this research were to ascertain the sorption capacity of these soils and to identify areas with high potential for P release from soils to ground water. We extracted 80 soil samples collected across the valley with ammonium oxalate and determined the ratio of extractable P to Fe and Al, from which we derived the degree of phosphorus saturation (DPS). A relatively low DPS (<15%) was observed in Histosols compared with the high DPS (>30%) observed in many of the hydromorphic organo-mineral soils. We used a sequential Gaussian simulation technique to assess the spatial pattern of the DPS and found that the Histosols have a low probability (<10%) of exceeding the widely used environmental DPS threshold of 25%. The areas characterized by mineral soils, such as hydromorphic Vertisols and various marl redoximorphic soils, have a high probability (>60%) of exceeding the threshold value. The ability to predict the concentrations of dissolved P in ground water based on DPS values was somewhat impaired because of the preferential flow characteristics in this altered wetland.     

Analysis of potentially mobile phosphorus in arable soils using solid state nuclear magnetic resonance

In many intensive agroecosystems continued inputs of phosphorus (P) over many years can significantly increase soil P concentrations and the risk of P loss to surface waters. For this study we used solid-state 31P nuclear magnetic resonance (NMR) spectroscopy, high-power decoupling with magic angle spinning (HPDec-MAS) NMR, and cross polarization with magic angle spinning (CP-MAS) NMR to determine the chemical nature of potentially mobile P associated with aluminum (Al) and calcium (Ca) in selected arable soils. Three soils with a range of bicarbonate-extractable Olsen P concentrations (40-102 mg P kg(-1)) were obtained from a long-term field experiment on continuous root crops at Rothamsted, UK, established in 1843 (sampled 1958). This soil has a threshold or change point at 59 mg Olsen P kg(-1), above which potentially mobile P (as determined by extraction with water or 0.01 M CaCl2) increases much more per unit increase in Olsen P than below this point. Results showed that CaCl2 and water preferentially extracted Al-P and Ca-P forms, respectively, from the soils. Comparison among the different soils also indicated that potentially mobile P above the threshold was largely present as a combination of soluble and loosely adsorbed (protonated-cross polarized) P forms largely associated with Ca, such as monetite (CaHPO4) and dicalcium phosphate dihydrate (CaHPO4-2H2O), and some Al-associated P as wavellite. The findings of this study demonstrate that solid-state NMR has the potential to provide accurate information on the chemical nature of soil P species and their potential mobility.     

Soil testing to predict phosphorus leaching

Subsurface pathways can play an important role in agricultural phosphorus (P) losses that can decrease surface water quality. This study evaluated agronomic and environmental soil tests for predicting P losses in water leaching from undisturbed soils. Intact soil columns were collected for five soil types that a wide range in soil test P. The columns were leached with deionized water, the leachate analyzed for dissolved reactive phosphorus (DRP), and the soils analyzed for water-soluble phosphorus (WSP), 0.01 M CaCl2 P (CaCl2-P), iron-strip phosphorus (FeO-P), and Mehlich-1 and Mehlich-3 extractable P, Al, and Fe. The Mehlich-3 P saturation ratio (M3-PSR) was calculated as the molar ratio of Mehlich-3 extractable P/[Al + Fe]. Leachate DRP was frequently above concentrations associated with eutrophication. For the relationship between DRP in leachate and all of the soil tests used, a change point was determined, below which leachate DRP increased slowly per unit increase in soil test P, and above which leachate DRP increased rapidly. Environmental soil tests (WSP, CaCl2-P, and FeO-P) were slightly better at predicting leachate DRP than agronomic soil tests (Mehlich-1 P, Mehlich-3 P, and the M3-PSR), although the M3-PSR was as good as the environmental soil tests if two outliers were omitted. Our results support the development of Mehlich-3 P and M3-PSR categories for profitable agriculture and environmental protection; however, to most accurately characterize the risk of P loss from soil to water by leaching, soil P testing must be fully integrated with other site properties and P management practices.     

Surface runoff losses of copper and zinc in sandy soils

Increased anthropogenic inputs of Cu and Zn in soils have caused considerable concern relative to their effect on water contamination. Copper and Zn contents in surface soil directly influence the movement of Cu and Zn. However, minimal information is available on runoff losses of Cu and Zn in agricultural soils, and soil-extractable Cu and Zn in relation to runoff water quality. Field experiments were conducted in 2001 to study dissolved Cu and Zn losses in runoff in Florida sandy soils under commercial citrus and vegetable production and the relationship between soil-extractable Cu and Zn forms and dissolved Cu and Zn concentrations in runoff water. Five extraction methods were compared for extracting soil available Cu and Zn. Concentrations of dissolved Cu and Zn in runoff were measured and runoff discharge was monitored. Mean dissolved Cu in field runoff water was significantly correlated with the extractable Cu obtained only by 0.01 mol L(-1) CaCl2, Mehlich 1, or DTPA-TEA methods. Dissolved Zn in runoff water was only significantly correlated with extractable Zn by 0.01 mol L(-1) CaCl2. The highest correlations to dissolved Cu in runoff were obtained when soil-available Cu was extracted by 0.01 mol L(-1) CaCl2. The results indicate that 0.01 mol L(-1) CaCl2-extractable Cu and Zn are the best soil indexes for predicting readily released Cu and Zn in the sandy soils. Both runoff discharge and 0.01 mol L(-1) CaCl2-extractable Cu and Zn levels had significant influences on Cu and Zn loads in surface runoff.     

Colloidal and dissolved phosphorus in sandy soils as affected by phosphorus saturation

Fertilization exceeding crop requirements causes an accumulation of phosphorus (P) in soils, which might increase concentrations of dissolved and colloidal P in drainage. We sampled soils classified as Typic Haplorthods from four fertilization experiments to test (i) whether increasing degrees of phosphorus saturation (DPS) increase concentrations of dissolved and colloidal P, and (ii) if critical DPS levels can be defined for P release from these soils. Oxalate-extractable concentrations of P, iron (Fe), and aluminum (Al) were quantified to characterize DPS. Turbidity, zeta potential, dissolved P, and colloidal P, Fe, Al, and carbon (C) concentrations were determined in water and KCl extracts. While concentrations of dissolved P decreased with increasing depth, concentrations of water-extractable colloidal P remained constant. In topsoils 28 +/- 17% and in subsoils 94 +/- 8% of water-extractable P was bound to colloids. Concentrations of dissolved P increased sharply for DPS > 0.1. Colloidal P concentrations increased with increasing DPS because of an additional mobilization of colloids and due to an increase of the colloids P contents. In addition to DPS, ionic strength and Ca(2+) affected the release of colloidal P. Hence, using KCl for extraction improved the relationship between DPS and colloidal P compared with water extraction. Accumulation of P in soils increases not only concentrations of dissolved P but also the risk of colloidal P mobilization. Leaching of colloidal P is potentially important for inputs of P into water bodies because colloidal P as the dominant water-extractable P fraction in subsoils was released from soils with relatively low DPS.     

An environmental threshold for degree of phosphorus saturation in sandy soils

There is critical need for a practical indicator to assess the potential for phosphorus (P) movement from a given site to surface waters, either via surface runoff or subsurface drainage. The degree of phosphorus saturation (DPS), which relates a measure of P already adsorbed by a soil to its P adsorption capacity, could be a good indicator of that soil's P release capability. Our primary objective was to find a suitable analytical protocol for determining DPS and to examine the possibility of defining a threshold DPS value for Florida's sandy soils. Four farmer-owned dairy sprayfields were selected within the Suwannee River basin and soil profiles were randomly obtained from each site, as well as from adjacent unimpacted sites. The soil samples were divided either by horizon or depth, and DPS was determined for each soil sample using ammonium-oxalate (DPS(Ox)), Mehlich-1 (DPS(M1)), and Mehlich-3 (DPS(M3)) extracts. All methods of DPS calculations were linearly related to one another (r2 > 0.94). Relationships between water-soluble P and DPS indicate that the respective change points are: DPS(Ox) = 20%, DPS(M1) = 20%, and DPS(M3) = 16%. These relationships include samples from Ap, E, and Bt horizons, and various combinations thereof, suggesting that DPS values can be used as predictors of P loss from a soil irrespective of the depth of the soil within a profile. Taking into consideration the change points, confidence intervals, agronomic soil test values, and DPS values from other studies, we suggest replacing Mehlich-1 P values in the Florida P Index with the three DPS categories (DPS(M1) = <30, 30-60, and >60%) to assign different P loss ratings in the P Index.     

Estimating runoff phosphorus losses from calcareous soils in the Minnesota River basin

Bioavailable phosphorus (BAP) in stormwater runoff is a key issue for control of eutrophication in agriculturally impacted watersheds. Laboratory experiments were conducted in soil runoff boxes to determine BAP content in simulated storm runoff in 10 (mostly) calcareous soils from the Minnesota River basin in southern Minnesota. The soluble reactive phosphorus (SRP) portion of the runoff BAP was significantly correlated with soil Mehlich-III P, Olsen P, and water-extractable P (all r2 > 0.90 and p < 0.001). A linear relationship (r2 = 0.88, p < 0.001) also was obtained between SRP in runoff and the phosphorus saturation index based on sorptivity (PSIs) calculated with sorptivity as a measure of the inherent soil P sorption capacity. Runoff levels of BAP estimated with iron oxide-impregnated paper were predicted well by various soil test P methods and the PSI, of the soils, but correlation coefficients between these variables and runoff BAP were generally lower than those for runoff SRP. Using these relationships and critical BAP levels for stream eutrophication, we found corresponding critical levels of soil Mehlich-III P and Olsen P (which should not be exceeded) to be 65 to 85 and 40 to 55 mg kg(-1), respectively.     

Estimating soil phosphorus requirements and limits from oxalate extract data

Excessive fertilizer and manure phosphorus (P) inputs to soils elevates P in soil solution and surface runoff, which can lead to freshwater eutrophication. Runoff P can be related to soil test P and P sorption saturation, but these approaches are restricted to a limited range of soil types or are difficult to determine on a routine basis. The purpose of this study was to determine whether easily measurable soil characteristics were related to the soil phosphorus requirements (P(req), the amount of P sorbed at a particular solution P level). The P(req) was determined for 18 chemically diverse soils from sorption isotherm data (corrected for native sorbed P) and was found to be highly correlated to the sum of oxalate-extractable Al and Fe (R2 > 0.90). Native sorbed P, also determined from oxalate extraction, was subtracted from the P(req) to determine soil phosphorus limits (PL, the amount of P that can be added to soil to reach P(req)). Using this approach, the PL to reach 0.2 mg P L(-1) in solution ranged between -92 and 253 mg P kg(-1). Negative values identified soils with surplus P, while positive values showed soils with P deficiency. The results showed that P, Al, and Fe in oxalate extracts of soils held promise for determining PL to reach up to 10 mg P L(-1) in solution (leading to potential runoff from many soils). The soil oxalate extraction test could be integrated into existing best management practices for improving soil fertility and protecting water quality.     

Relating soil phosphorus to dissolved phosphorus in runoff: a single extraction coefficient for water quality modeling

Phosphorus transport from agricultural soils contributes to eutrophication of fresh waters. Computer modeling can help identify agricultural areas with high potential P transport. Most models use a constant extraction coefficient (i.e., the slope of the linear regression between filterable reactive phosphorus [FRP] in runoff and soil P) to predict dissolved P release from soil to runoff, yet it is unclear how variations in soil properties, management practices, or hydrology affect extraction coefficients. We investigated published data from 17 studies that determined extraction coefficients using Mehlich-3 or Bray-1 soil P (mg kg(-1)), water-extractable soil P (mg kg(-1)), or soil P sorption saturation (%) as determined by ammonium oxalate extraction. Studies represented 31 soils with a variety of management conditions. Extraction coefficients from Mehlich-3 or Bray-1 soil P were not significantly different for 26 of 31 soils, with values ranging from 1.2 to 3.0. Extraction coefficients from water-extractable soil P were not significantly different for 17 of 20 soils, with values ranging from 6.0 to 18.3. The relationship between soil P sorption saturation and runoff FRP (microg L(-1)) was the same for all 10 soils investigated, exhibiting a split-line relationship where runoff FRP rapidly increased at P sorption saturation values greater than 12.5%. Overall, a single extraction coefficient (2.0 for Mehlich-3 P data, 11.2 for water-extractable P data, and a split-line relationship for P sorption saturation data) could be used in water quality models to approximate dissolved P release from soil to runoff for the majority of soil, hydrologic, or management conditions. A test for soil P sorption saturation may provide the most universal approximation, but only for noncalcareous soils.     

Phosphate release from seasonally flooded soils: a laboratory microcosm study

Phosphorus derived from agricultural practices has been targeted as a leading cause of water quality degradation in Lake Champlain. Mobilization of P from seasonally flooded agricultural soils is a concern. Using 14 soils from a research farm in New York's Champlain Valley, we characterized the available P status, extractable Fe and Al, P sorption capacities, and soluble phosphate release in flooded laboratory microcosms. Quantities of NH4-acetate available P ranged from 3 to 100 mg kg(-1) and fluoride-extractable P from 10 to 211 mg kg(-1). Flooding soils induced significant release of phosphate to the porewater over a 60- to 90-d period in 13 of the 14 soils studied. Porewater phosphate increases ranged from 2.2 to 27.0 times the initial phosphate concentrations. However, floodwater phosphate increases were much lower, with a maximum of 3.6 times the initial concentration. Average porewater phosphate concentrations over the flooding period ranged from 0.046 to 7.0 mg L(-1) and average floodwater P from 0.032 to 3.70 mg L(-1). Ammonium-acetate P and the degree of phosphorus saturation (DPS) were highly correlated with the average porewater and floodwater phosphate concentration. Average ratio of porewater to floodwater phosphate concentrations ranged from 1.0 to 3.3. Five soils that were lower in fluoride-extractable P had increasing porewater phosphate accompanied by increasing porewater Fe2+ and decreasing floodwater phosphate. Results suggest that P solubility and mobility were a function of both the available P status and redox cycling.     

Phosphorus forms in biosolids-amended soils and losses in runoff: effects of wastewater treatment process

Continuous addition of municipal biosolids to soils based on plant nitrogen (N) requirements can cause buildup of soil phosphorus (P) in excess of crop requirements; runoff from these soils can potentially contribute to nonpoint P pollution of surface waters. However, because biosolids are often produced using lime and/or metal salts, the potential for biosolids P to cause runoff P losses can vary with wastewater treatment plant (WWTP) process. This study was conducted to determine the effect of wastewater treatment process on the forms and amounts of P in biosolids, biosolids-amended soils, and in runoff from biosolids-amended soils. We amended two soil types with eight biosolids and a poultry litter (PL) at equal rates of total P (200 kg ha(-1); unamended soils were used as controls. All biosolids and amended soils were analyzed for various types of extractable P, inorganic P fractions, and the degree of P saturation (acid ammonium oxalate method). Amended soils were placed under a simulated rainfall and all runoff was collected and analyzed for dissolved reactive phosphorus (DRP), iron-oxide-coated filter paper strip-extractable phosphorus (FeO-P), and total phosphorus (EPA3050 P). Results showed that biosolids produced with a biological nutrient removal (BNR) process caused the highest increases in extractable soil P and runoff DRP. Alternatively, biosolids produced with iron only consistently had the lowest extractable P and caused the lowest increases in extractable soil P and runoff DRP when added to soils. Differences in soil and biosolids extractable P levels as well as P runoff losses were related to the inorganic P forms of the biosolids.     

Phosphorus leaching in manure-amended Atlantic Coastal Plain soils

Targeting the sources of phosphorus (P) and transport pathways of drainage from agricultural land will assist in the reduction of P loading to surface waters. Our research investigated the vertical movement of P from dairy manure and broiler litter through four Atlantic Coastal Plain soils. A randomized split-plot design with two main-plot tillage treatments (no tillage [NT] and chisel tillage [CH]) and five manure P rate split-plot treatments was used at each location. The split-plot P rates were 0, 100, 200, 300, and 400 kg P ha(-1) yr(-1). Four consecutive years of manure application began at all sites 5 yr before sampling. Soils were sampled to a depth of 150 cm from each split plot in seven depth increments and analyzed for soil test phosphorus (STP), water-extractable soil phosphorus (WSP), and degree of phosphorus saturation (DPS). The DPS of the 0- to 15-cm depths confirmed that at the 100 kg P ha(-1) yr(-1) application rate, all sites exceeded the threshold for P saturation (30%). At depths greater than 30 cm, DPS was typically below the 30% saturation threshold. The DPS change points ranged from 25 to 34% for the 0- to 90-cm depths. Our research concluded that the risk of P leaching through the matrix of the Atlantic Coastal Plain soils studied was not high; however, P leaching via macropore bypass may contribute to P loss from these soils.     

Use of drinking water treatment residuals as a potential best management practice to reduce phosphorus risk index scores

The P risk index system has been developed to identify agricultural fields vulnerable to P loss as a step toward protecting surface water. Because of their high Langmuir phosphorus adsorption maxima (P(max)), use of drinking water treatment residuals (WTRs) should be considered as a best management practice (BMP) to lower P risk index scores. This work discusses three WTR application methods that can be used to reduce P risk scores: (i) enhanced buffer strip, (ii) incorporation into a high soil test phosphorus (STP) soil, and (iii) co-blending with manure or biosolids. The relationship between WTR P(max) and reduction in P extractability and runoff P was investigated. In a simulated rainfall experiment, using a buffer strip enhanced with 20 Mg WTR ha(-1), runoff P was reduced by from 66.8 to 86.2% and reductions were related to the WTR P(max). When 25 g kg(-1) WTR was incorporated into a high STP soil of 315 mg kg(-1) determined using Mehlich-3 extraction, 0.01 M calcium chloride-extractable phosphorus (CaCl(2)-P) reductions ranged from 60.9 to 96.0% and were strongly (P < 0.01) related to WTR P(max). At a 100 g kg(-1) WTR addition, Mehlich 3-extractable P reductions ranged from 41.1 to 86.7% and were strongly (P < 0.01) related to WTR P(max). Co-blending WTR at 250 g kg(-1) to manure or biosolids reduced CaCl(2)-P by >75%. The WTR P(max) normalized across WTR application rates (P(max) x WTR application) was significantly related to reductions in CaCl(2)-P or STP. Using WTR as a P risk index modifying factor will promote effective use of WTR as a BMP to reduce P loss from agricultural land.