Air quality in Brunei Darussalam during the 1998 haze episode

Regional haze from biomass burning in SE Asia is a recurring air pollution phenomenon with a potential impact on the health of several hundred million people. Air quality data in Brunei Darussalam during the 1998 haze episode revealed that only particulate matter is a significant pollutant. The WHO guideline of 70 μg m⁻³ for PM₁₀ (24 h average) was exceeded on 54 days during the haze episode which lasted from 1 February to 30 April 1998. Concentrations of SO₂, NO₂, and O₃ were all below WHO guidelines and the 8 h guideline for CO was exceeded on only seven occasions. Average daily PM₁₀ concentrations were below 450 μg m⁻³ but concentrations greater than 600 μg m⁻³ persisted for several hours at a time and total exposure to such high concentrations could add up to several days over the course of a haze episode. Airborne particles exhibited diurnal variation, typically rising through the night to very high levels in the early morning and thereafter decreasing due largely to meteorological factors. The pollutant standards index (PSI), widely used to report urban air quality, may not be suitable for haze from forest fires as it does not take into account short-term exposure to extremely high particle concentrations of up to 1 mg m⁻³.     

PM10 and PM2.5 concentrations in Central and Eastern Europe:: results from the Cesar study

Between November 1995 and October 1996, particulate matter concentrations (PM₁₀ and PM_2.5) were measured in 25 study areas in six Central and Eastern European countries: Bulgaria, Czech Republic, Hungary, Poland, Romania and Slovak Republic. To assess annual mean concentration levels, 24-h averaged concentrations were measured every sixth day on a fixed urban background site using Harvard impactors with a 2.5 and 10 μm cut-point. The concentration of the coarse fraction of PM₁₀ (PM_10−2.5) was calculated as the difference between the PM₁₀ and the PM_2.5 concentration. Spatial variation within study areas was assessed by additional sampling on one or two urban background sites within each study area for two periods of 1 month. QA/QC procedures were implemented to ensure comparability of results between study areas. A two to threefold concentration range was found between study areas, ranging from an annual mean of 41 to 98 μg m⁻³ for PM₁₀, from 29 to 68 μg m⁻³ for PM_2.5 and from 12 to 40 μg m⁻³ for PM_10−2.5. The lowest concentrations were found in the Slovak Republic, the highest concentrations in Bulgaria and Poland. The variation in PM₁₀ and PM_2.5 concentrations between study areas was about 4 times greater than the spatial variation within study areas suggesting that measurements at a single sampling site sufficiently characterise the exposure of the population in the study areas. PM₁₀ concentrations increased considerably during the heating season, ranging from an average increase of 18 μg m⁻³ in the Slovak Republic to 45 μg m⁻³ in Poland. The increase of PM₁₀ was mainly driven by increases in PM_2.5; PM_10−2.5 concentrations changed only marginally or even decreased. Overall, the results indicate high levels of particulate air pollution in Central and Eastern Europe with large changes between seasons, likely caused by local heating.     

What are the sources and conditions responsible for exceedences of the 24 h PM10 limit value (50 μg m−3) at a heavily trafficked London site?

The European Union has set limit values for PM₁₀ to be met in 2005. At Marylebone Road, London, where the traffic is heavy, the daily limit value of 50 μg m⁻³ is exceeded more than 35 times a year. A total of 185 days with daily PM₁₀ concentrations exceeding the limit value of 50 μg m⁻³ measured between January 2002 and December 2004 (data capture of 89.5%) are discussed in this paper. These exceedences were more frequent in early spring and in autumn. Concentrations have been disaggregated into regional, urban (background) and local (street) contributions. Most of the episodes of gravimetric PM₁₀ above the limit value were associated with a high regional background and very often the regional contribution dominated the PM₁₀ mass. The secondary aerosol (especially the particulate nitrate) made a major contribution to the PM₁₀ load. These situations were frequently observed when air masses came from the European mainland (showing that both emissions from the UK and other EU countries contributed to the exceedences), and less frequently with maritime air masses that have stagnated over the UK (showing that emissions from the UK alone less frequently contributed to the high regional background). However, the higher frequency of episodes breaching the limit value at the roadside site than at the rural site and the higher frequency of PM₁₀ concentrations above the limit value on weekdays show that the high regional contributions are additional to local and urban emissions. Local emissions mainly due to traffic were the second important contributor to the exceedences, while the contribution of the urban background of London was less important than the local emissions and the regional background. Applying the pragmatic mass closure model of Harrison et al. [2003. A pragmatic mass closure model for airborne particulate matter at urban background and roadside sites. Atmospheric Environment 37, 4927–4933], revealed that the regional aerosol is comprised very largely of ammonium nitrate and sulphate and secondary organic aerosol. Findings suggest that international abatement of secondary aerosol precursors may be the most effective measure to fulfil the requirements of the European Directive 1999/30/CE by lowering the regional background.     

Spatial variation of mass concentration of roadside suspended particulate matter in metropolitan Hong Kong

This study conducted roadside particulate sampling to measure the total suspended particulate (TSP), PM₁₀ (particles <10 μm in aerodynamic diameter) and PM_2.5 (particles <2.5 μm in aerodynamic diameter) mass concentration in 11 urbanized and densely populated districts in Hong Kong. One hundred and thirty-three samples were obtained to measure the mass concentrations of TSP, PM₁₀ and PM_2.5. According to these results, the TSP, PM₁₀ and PM_2.5 mass concentrations varied from 94.85 to 301.63 μg m⁻³, 67.67 to 142.68 μg m⁻³ and 50.01 to 125.12 μg m⁻³, respectively. The PM_2.5/PM₁₀ ratio of all samples was 0.82 which ranged from 0.62 to 0.95. The PM levels and PM ratios in metropolitan Hong Kong significantly fluctuated from site-to-site and over time. The PM_2.5 mass concentration in different districts corresponding to urban industrial, new town, urban residential and urban commercial were 77.64, 87.50, 106.96 and 88.54 μg m⁻³, respectively. The PM_2.5 level is high in Hong Kong, and for individual sampling, more than 60% daily measurements exceeded the NAAQS. The mass fraction of PM_2.5 in PM₁₀ and TSP is relatively high when compared with overseas studies.     

Field performance of dichotomous sequential PM air samplers

For over one year, the Environmental Protection Commission of Hillsborough County (EPCHC) in Tampa, Florida, operated two dichotomous sequential particulate matter air samplers collocated with a manual Federal Reference Method (FRM) air sampler at a waterfront site on Tampa Bay. The FRM was alternately configured as a PM_2.5, then as a PM₁₀ sampler. For the dichotomous sampler measurements, daily 24-h integrated PM_2.5 and PM_10–2.5 ambient air samples were collected at a total flow rate of 16.7 l min⁻¹. A virtual impactor split the air into flow rates of 1.67 and 15.0 l min⁻¹ onto PM_10–2.5 and PM_2.5 47-mm diameter PTFE^® filters, respectively. Between the two dichotomous air samplers, the average concentration, relative bias and relative precision were 13.3 μg m⁻³, 0.02% and 5.2% for PM_2.5 concentrations (n=282), and 12.3 μg m⁻³, 3.9% and 7.7% for PM_10–2.5 concentrations (n=282). FRM measurements were alternate day 24-h integrated PM_2.5 or PM₁₀ ambient air samples collected onto 47-mm diameter PTFE^® filters at a flow rate of 16.7 l min⁻¹. Between a dichotomous and a PM_2.5 FRM air sampler, the average concentration, relative bias and relative precision were 12.4 μg m⁻³, −5.6% and 8.2% (n=43); and between a dichotomous and a PM₁₀ FRM air sampler, the average concentration, relative bias and relative precision were 25.7 μg m⁻³, −4.0% and 5.8% (n=102). The PM_2.5 concentration measurement standard errors were 0.95, 0.79 and 1.02 μg m⁻³; for PM₁₀ the standard errors were 1.06, 1.59, and 1.70 μg m⁻³ for two dichotomous and one FRM samplers, respectively, which indicate the dichotomous samplers have superior technical merit. These results reveal the potential for the dichotomous sequential air sampler to replace the combination of the PM_2.5 and PM₁₀ FRM air samplers, offering the capability of making simultaneous, self-consistent determinations of these particulate matter fractions in a routine ambient monitoring mode.     

Commuter exposure to particulate matter in public transportation modes in Hong Kong

This study examined commuter’s exposure to respirable suspended particulate matters while commuting in public transportation modes. The survey was conducted between October 1999 and January 2000 in Hong Kong. A total of eight public transportation modes, that are bus, tram, public light bus, taxi, ferry, Kowloon–Canton Railway, Mass Transit Railway and Light Rail Transit, were selected in the study. They were grouped into four categories: (T1) railway transport; (T2) non-air-conditioned roadway transport; (T3) air-conditioned roadway transport and (T4) marine transport. Both PM₁₀ and PM_2.5 levels were investigated. The results indicate that the particulate level is greatly affected by the mode of transport as well as the ventilation system of the transport. The overall average PM₁₀ concentration level in T2 (147 μg m⁻³) is the highest and is followed by T4 (81 μg m⁻³) and T3 (65 μg m⁻³). The PM₁₀ level in T1 (50 μg m⁻³) is the lowest. Notably, the commuter exposure in tram (175 μg m⁻³) is the highest among all the monitored commuting modes. Commuting modes such as railway and air-conditioned vehicle are recommended as a substitute for non-air-conditioned vehicle. The PM_2.5 to PM₁₀ ratio in transports ranged from 63% to 78%. Higher PM_2.5 to PM₁₀ ratio is found in vehicles with air-conditioning system. For the double deck vehicle, higher PM₁₀ level has resulted in the lower deck. The average upper-deck to lower-deck PM₁₀ ratio is 0.836, 0.751 and 0.738 in air-conditioned bus, non-air-conditioned bus and non-air-conditioned tram, respectively. Typical concentration profiles in different transports are also presented.     

Chemical composition of aerosols during a major biomass burning episode over northern Europe in spring 2006: Experimental and modelling assessments

The long-range transported smokes emitted by biomass burning had a strong impact on the PM_2.5 mass concentrations in Helsinki over the 12 days period in April and May 2006. To characterize aerosols during this period, the real-time measurements were done for PM_2.5, PM_2.5–10, common ions and black carbon. Moreover, the 24-h PM₁ filter samples were analysed for organic and elemental carbon (OC and EC), water-soluble organic carbon (WSOC), ions and levoglucosan. The Finnish emergency and air quality modelling system SILAM was used for the forecast of the PM_2.5 concentration generated by biomass burning. According to the real-time PM_2.5 data, the investigated period was divided into four types of PM situations: episode 1 (EPI-1; 25–29 April), episode 2 (EPI-2; 1–5 May), episode 3 (EPI-3; 5–6 May) and a reference period (REF; 24 March–24 April). EPI-3 included a local warehouse fire and therefore it is discussed separately. The PM₁ mass concentrations of biomass burning tracers—levoglucosan, potassium and oxalate—increased during the two long-range transport episodes (EPI-1 and EPI-2). The most substantial difference between the episodes was exhibited by the sulphate concentration, which was 4.9 (±1.4) μg m⁻³ in EPI-2 but only 2.4 (±0.31) μg m⁻³ in EPI-1 being close to that of REF (1.8±0.54 μg m⁻³). The concentration of particulate organic matter in PM₁ was clearly higher during EPI-1 (11±3.3 μg m⁻³) and EPI-2 (9.7±4.0 μg m⁻³) than REF (1.3±0.45 μg m⁻³). The long-range transported smoke had only a minor impact on the WSOC-to-OC ratio. According to the model simulations, MODIS detected the fires that caused the first set of concentration peaks (EPI-1) and the local warehouse fire (EPI-3), but missed the second one (EPI-2) probably due to dense frontal clouds.     

Modelling long-range transport of primary particulate material over Europe

This paper uses a simple model of atmospheric transport and an emissions inventory prepared by TNO to estimate the contribution of primary particulate material to PM₁₀ and PM_2.5 concentration across Europe. The resulting population exposure is compared with that of secondary particulates, and it is noted that both primary and secondary contributions will be significantly reduced with the implementation of new protocols under the Convention on Long-Range Transboundary Air Pollution (CLRTAP). Since concentrations of primary PM₁₀ can become elevated in episodic situations, when long-range transport of particulate could, on its own, exceed 24 h average targets of 50 μg m⁻³ over large areas of Europe, such reduction is important for achievement of current air quality standards to control exposure to atmospheric particulate PM₁₀.     

Characteristics of vertical profiles and sources of PM2.5, PM10 and carbonaceous species in Beijing

In August 2003 during the anticipated month of the 2008 Beijing Summer Olympic Games, we simultaneously collected PM₁₀ and PM_2.5 samples at 8, 100, 200 and 325 m heights up a meteorological tower and in an urban and a suburban site in Beijing. The samples were analysed for organic carbon (OC) and elemental carbon (EC) contents. Particulate matter (PM) and carbonaceous species pollution in the Beijing region were serious and widespread with 86% of PM_2.5 samples exceeding the daily National Ambient Air Quality Standard of the USA (65 μg m⁻³) and the overall daily average PM₁₀ concentrations of the three surface sites exceeding the Class II National Air Quality Standard of China (150 μg m⁻³). The maximum daily PM_2.5 and PM₁₀ concentrations reached 178.7 and 368.1 μg m⁻³, respectively, while those of OC and EC reached 22.2 and 9.1 μg m⁻³ in PM_2.5 and 30.0 and 13.0 μg m⁻³ in PM₁₀, respectively. PM, especially PM_2.5, OC and EC showed complex vertical distributions and distinct layered structures up the meteorological tower with elevated levels extending to the 100, 200 and 300 m heights. Meteorological evidence suggested that there exist fine atmospheric layers over urban Beijing. These layers were featured by strong temperature inversions close to the surface (<50 m) and more stable conditions aloft. They enhanced the accumulation of pollutants and probably caused the complex vertical distributions of PM and carbonaceous species over urban Beijing. The built-up of PM was accompanied by transport of industrial emissions from the southwest direction of the city. Emissions from road traffic and construction activities as well as secondary organic carbon (SOC) are important sources of PM. High OC/EC ratios (range of 1.8–5.1 for PM_2.5 and 2.0–4.3 for PM₁₀) were found, especially in the higher levels of the meteorological tower suggesting there were substantial productions of SOC in summer Beijing. SOC is estimated to account for at least 33.8% and 28.1% of OC in PM_2.5 and PM₁₀, respectively, with higher percentages at the higher levels of the tower.     

Airborne particle PM2.5/PM10 mass distribution and particle-bound PAH concentrations near a medical waste incinerator

This study attempts to determine the influence of air quality in a residential area near a medical waste incineration plant. Ambient air concentrations of polycyclic aromatic hydrocarbons (PAHs), PM₁₀ and PM_2.5 (PM—particulate matter) were determined by collecting air samples in areas both upwind and downwind of the plant. The differences in air pollutant levels between the study area and a reference area 11 km away from the plant were evaluated.Dichotomous samplers were used for sampling PM_2.5 and PM₁₀ from ambient air. Two hundred and twenty samples were obtained from the study area, and 100 samples were taken from a reference area. Samples were weighed by an electronic microbalance and concentrations of PM_2.5 and PM₁₀ were determined. A HPLC equipped with a fluorescence detector was employed to analyze the concentrations of 15 PAHs compounds adsorbed into PM_2.5 and PM₁₀.The experimental results indicated that the average concentrations of PM_2.5 and PM₁₀ were 30.34±17.95 and 36.81±20.45 μg m⁻³, respectively, in the study area, while the average ratio of PM_2.5/PM₁₀ was 0.82±0.01. The concentrations of PM_2.5 and PM₁₀ of the study area located downwind of the incinerator were significantly higher than the study area upwind of the incinerator (P<0.05).The concentration of PAHs in PM_2.5 in the study area was 2.2 times higher than in the reference area (P<0.05). Furthermore, the benzo(a)pyrene concentrations in PM_2.5 and PM₁₀ were 0.11±0.05 ng m⁻³ and 0.12±0.06 ng m⁻³ in the study area, respectively. The benzo(a)pyrene concentrations of PM_2.5 and PM₁₀ in the study area were 7 and 5.3 times higher than in the reference area (P<0.05), respectively.The study indicated that the air quality of PM_2.5, PM₁₀ and PAHs had significant contamination by air pollutants emitted from a medical waste incineration factory, representing a public health problem for nearby residences, despite the factory being equipped with a modern air pollution control system.     

Assessment of road users’ elemental carbon personal exposure levels,London, UK

Little is known about particulate elemental carbon (EC) personal exposure levels, a key component of diesel exhaust, specifically in transport microenvironments. A method utilizing the optical properties of EC particles has been applied to personal exposure measurement filter samples. In a series of field studies carried out in London, UK, during 1999–2000 over 400 fine particle (PM_2.5) personal exposure level measurements were taken for journeys in bicycle, bus, car and underground rail transport microenvironments, along three main fixed routes. The particulate EC contribution to the PM_2.5 personal exposure was assessed indirectly by means of an optical technique and with the development and use of a size fraction specific and site-specific calibration curve. In this first EC personal exposure study of transport users geometric mean exposure levels in the summer field campaign were 11.2 μg m⁻³ (GSD=2.7) for cyclists, 13.6 μg m⁻³ (GSD=1.9) for bus passengers and 21.6 μg m⁻³ (GSD=2.1) for car drivers; corresponding exposure levels in the winter were 16.4 μg m⁻³ (GSD=1.8), 18.6 μg m⁻³ (GSD=2.3) and 27.3 μg m⁻³ (GSD=2.0), respectively. EC/PM_2.5 ratios were approximately 0.5–0.6 for bicycle and bus modes and 0.7–0.8 for the car mode. EC/PM_2.5 ratios for different routes ranged from approximately 0.7 for Route 1 to 0.4 for Route 3. Cyclists had the lowest exposure to EC, and car occupants the highest exposure. A large difference in exposure levels between a central high traffic density route and the other less central routes was observed. Particulate EC was a very significant proportion of the total PM_2.5 personal exposure and EC personal exposure levels were considerably higher than reported fixed site monitor EC concentrations.     

Study of aluminium distribution and speciation in atmospheric particles of different diameters in Nanjing,China

Aluminium (Al) is one of the trace inorganic metals present in atmospheric particles. Al speciation study is essential to better evaluate the mobility, availability, and persistence of trace Al and Al species in the atmosphere. This paper reports Al distribution and speciation in atmospheric particles with aerodynamic diameters >10.0, 10.0–2.5 and <2.5 μm in the urban area of Nanjing, China. Urban particles were collected with a high-volume sampling system equipped with a cascade impactor, which effectively separates the particulate matter into three size ranges. Particulate Al was fractionated into five different forms (insoluble, oxide, organic, carbonate, and exchangeable species) by the modified five-step Tessier's sequential extraction procedure. The main points are as follows: (1) The average levels of Al in PM_2.5, PM_2.5–10 and PM_>10 are 2.02±0.35, 3.04±0.43 and 6.32±0.76 μg m⁻³, respectively, with PM_2.5, PM_2.5–10 and PM_>10 constituting respectively, 17.8±3.1%, 26.7±3.8% and 55.5±6.7% of suspended particulate matter (SPM) mass (11.38 μg m⁻³). (2) The vertical profile of airborne Al in the above three size fractions has been estimated. A significant increase in airborne Al concentrations was found for PM_2.5, PM_2.5–10 and PM_>10 as the sampling height above the ground increased from 2.5 to 17.5 m; however, there was an obvious decrease in airborne Al concentrations between 17.5 and 40.0 m. The maximum mean of total Al in PM_2.5, PM_2.5–10 and PM_>10 occurred between 12.5 and 20.0 m above the ground. (3) The distribution of Al speciation was studied. It was found that the size distribution of airborne Al species followed the order: insoluble species>oxide species>organic species>carbonate species>exchangeable species.     

Source apportionment of ambient PM2.5 at five spanish centres of the european community respiratory health survey (ECRHS II)

Fine particulate matter (PM_2.5) was sampled at 5 Spanish locations during the European Community Respiratory Health Survey II (ECRHS II). In an attempt to identify and quantify PM_2.5 sources, source contribution analysis by principal component analysis (PCA) was performed on five datasets containing elemental composition of PM_2.5 analysed by ED-XRF. A total of 4–5 factors were identified at each site, three of them being common to all sites (interpreted as traffic, mineral and secondary aerosols) whereas industrial sources were site-specific. Sea-salt was identified as independent source at all coastal locations except for Barcelona (where it was clustered with secondary aerosols). Despite their typically dominant coarse grain-size distribution, mineral and marine aerosols were clearly observed in PM_2.5. Multi-linear regression analysis (MLRA) was applied to the data, showing that traffic was the main source of PM_2.5 at the five sites (39–53% of PM_2.5, 5.1–12.0 μg m⁻³), while regional-scale secondary aerosols accounted for 14–34% of PM_2.5 (2.6–4.5 μg m⁻³), mineral matter for 13–31% (2.4–4.6 μg m⁻³) and sea-salt made up 3–7% of the PM_2.5 mass (0.4–1.3 μg m⁻³). Consequently, despite regional and climatic variability throughout Spain, the same four main PM_2.5 emission sources were identified at all the study sites and the differences between the relative contributions of each of these sources varied at most 20%. This would corroborate PM_2.5 as a useful parameter for health studies and environmental policy-making, owing to the fact that it is not as subject to the influence of micro-sitting as other parameters such as PM₁₀. African dust inputs were observed in the mineral source, adding on average 4–11 μg m⁻³ to the PM_2.5 daily mean during dust outbreaks. On average, levels of Al, Si, Ti and Fe during African episodes were higher by a factor of 2–8 with respect to non-African days, whereas levels of local pollutants (absorption coefficient, S, Pb, Cl) showed smaller variations (factor of 0.5–2).     

The use of receptor modelling and emission inventory data to explain the downward trend in UK PM10 concentrations

Statistically significant downward trends in measured UK annual mean PM₁₀ concentrations have been observed at eight out of the nine urban background monitoring sites between the start of monitoring in 1992 or 1993 and 2000.Site-specific projections of the individual components of measured PM₁₀ concentrations have been derived for the period 1992–2000 at three monitoring sites from receptor modelling results for 1999 monitoring data. Measured annual average PM₁₀ concentrations declined to between 71% and 66% of the 1992 values during this period at the sites studied. The largest contributions to the decline in total PM₁₀ are from secondary particles at London Bloomsbury (40%, 3.4 μg m⁻³, tapered element oscillating microbalance (TEOM)), stationary sources at Belfast Centre (53%, 4.6 μg m⁻³, TEOM) and roadside traffic emissions at Bury Roadside (49%, 5.0 μg m⁻³, TEOM). The good agreement between the projected total PM₁₀ concentrations and measured values for the years 1992–2000 indicate that the combination of the receptor model and the site-specific projections provide a suitably robust method for predicting future PM₁₀ concentrations and the quantification of the impact of possible future policy measures to reduce PM₁₀ concentrations. The good agreement between the projections and measured concentration also provides a useful verification of the trends in emissions inventory estimates for the 1990s.Projections of estimated PM₁₀ concentrations have also been calculated for the London Bloomsbury site for the period from 1970 to 1991. Annual mean concentrations are predicted to have been in the range from 30 to 35 μg m⁻³, TEOM from 1977 to 1991 but much higher at values between 39 and 46 μg m⁻³, TEOM in the early 1970s.     

Particulate matter in the indoor air of classrooms—exploratory results from Munich and surrounding area

Numerous epidemiological studies have demonstrated the association between particle mass (PM) concentration in outside air and the occurrence of health related problems and/or diseases. However, much less is known about indoor PM concentrations and associated health risks. In particular, data are needed on air quality in schools, since children are assumed to be more vulnerable to health hazards and spend a large part of their time in classrooms.On this background, we evaluated indoor air quality in 64 schools in the city of Munich and a neighbouring district outside the city boundary. In winter 2004–2005 in 92 classrooms, and in summer 2005 in 75 classrooms, data on indoor air climate parameters (temperature, relative humidity), carbon dioxide (CO₂) and various dust particle fractions (PM₁₀, PM_2.5) were collected; for the latter both gravimetrical and continuous measurements by laser aerosol spectrometer (LAS) were implemented. In the summer period, the particle number concentration (PNC), was determined using a scanning mobility particle sizer (SMPS). Additionally, data on room and building characteristics were collected by use of a standardized form. Only data collected during teaching hours were considered in analysis. For continuously measured parameters the daily median was used to describe the exposure level in a classroom.The median indoor CO₂ concentration in a classroom was 1603 ppm in winter and 405 ppm in summer. With LAS in winter, median PM concentrations of 19.8 μg m⁻³ (PM_2.5) and 91.5 μg m⁻³ (PM₁₀) were observed, in summer PM concentrations were significantly reduced (median PM_2.5=12.7 μg m⁻³, median PM₁₀=64.9 μg m⁻³). PM_2.5 concentrations determined by the gravimetric method were in general higher (median in winter: 36.7 μg m⁻³, median in summer: 20.2 μg m⁻³) but correlated strongly with the LAS-measured results. In explorative analysis, we identified a significant increase of LAS-measured PM_2.5 by 1.7 μg m⁻³ per increase in humidity by 10%, by 0.5 μg m⁻³ per increase in CO₂ indoor concentration by 100 ppm, and a decrease by 2.8 μg m⁻³ in 5–7th grade classes and by 7.3 μg m⁻³ in class 8–11 compared to 1–4th class. During the winter period, the associations were stronger regarding class level, reverse regarding humidity (a decrease by 6.4 μg m⁻³ per increase in 10% humidity) and absent regarding CO₂ indoor concentration. The median PNC measured in 36 classrooms ranged between 2622 and 12,145 particles cm⁻³ (median: 5660 particles cm⁻³).The results clearly show that exposure to particulate matter in school is high. The increased PM concentrations in winter and their correlation with high CO₂ concentrations indicate that inadequate ventilation plays a major role in the establishment of poor indoor air quality. Additionally, the increased PM concentration in low level classes and in rooms with high number of pupils suggest that the physical activity of pupils, which is assumed to be more pronounced in younger children, contributes to a constant process of resuspension of sedimented particles. Further investigations are necessary to increase knowledge on predictors of PM concentration, to assess the toxic potential of indoor particles and to develop and test strategies how to ensure improved indoor air quality in schools.     

Quantifying the effect of urban tree planting on concentrations and depositions of PM10 in two UK conurbations

Trees are efficient scavengers of particulate matter and are characterised by higher rates of dry deposition than other land types. To estimate the potential of urban tree planting for the mitigation of urban PM₁₀ concentrations, an atmospheric transport model was used to simulate the transport and deposition of PM₁₀ across two UK conurbations (the West Midlands and Glasgow). Tree planting was simulated by modifying the land cover database, using GIS techniques and field surveys to estimate reasonable planting potentials. The model predicts that increasing total tree cover in West Midlands from 3.7% to 16.5% reduces average primary PM₁₀ concentrations by 10% from 2.3 to 2.1 μg m⁻³ removing 110 ton per year of primary PM₁₀ from the atmosphere. Increasing tree cover of the West Midlands to a theoretical maximum of 54% by planting all available green space would reduce the average PM₁₀ concentration by 26%, removing 200 ton of primary PM₁₀ per year. Similarly, for Glasgow, increasing tree cover from 3.6% to 8% reduces primary PM₁₀ concentrations by 2%, removing 4 ton of primary PM₁₀ per year. Increasing tree cover to 21% would reduce primary PM₁₀ air concentrations by 7%, removing 13 ton of primary PM₁₀ per year.     

Characterization of size-fractionated particulate mercury in Shanghai ambient air

The size-fractionated particulate mercury in ambient air was collected at the top of a university campus building in Shanghai from March 2002 to September 2003. Wet digestion followed by cold vapor atom adsorption spectroscopy (CVAAS) was employed to analyze total particulate mercury concentration. Two-step extraction was performed to differentiate volatile particle-phase mercury (VPM), reactive particle-phase mercury (RPM) and inert particle-phase mercury (IPM). The average concentrations of mercury in PM_1.6, PM₈ and total suspended particle (TSP) were 0.058–0.252, 0.148–0.398 and 0.233–0.529 ng m⁻³, respectively. About 50%–60% of mercury in PM₈ was in PM_1.6, and about 60%–70% of mercury in TSP was in PM₈. Particulate mercury was mainly concentrated on fine particles. The mercury fraction in fine particulate matters (<1.6 μm) was over 4 μg g⁻¹ while 1–2 μg g⁻¹ in TSP. Both were much higher than background values, suggesting that anthropogenic sources are the predominant emission contributors. Seasonal variation indicated that the mercury in TSP in spring was higher than that in summer; however, the mercury in fine particles (<1.6 μm) varied little. The fact that fine particulate mercury (<1.6 μm) was well correlated with sulfate and elemental carbon, but not with fluoride, chloride, nitrate and organic carbon, demonstrates that fine particulate mercury is closely associated with stationary sources and gas–particle transformation. Speciation analysis of mercury showed that VPM fraction decreased with the decrease of particle size, while IPM fraction increased and occupied over 50% in particle <1.6 μm. The detailed species in VPM, RPM and IPM were discussed. Coal burning was estimated to contribute approximately 80% of total atmospheric mercury.     

Particulate matter and manganese exposures in Toronto,Canada

Methylcyclopentadienyl manganese tricarbonyl (MMT) is a manganese-based gasoline additive used to enhance automobile performance. MMT has been used in Canadian gasoline for about 20 yr. Because of the potential for increased levels of Mn in particulate matter resulting from automotive exhausts, a large-scale population-based exposure study (∼1000 participant periods) was conducted in Toronto, Canada, to estimate the distribution of 3-day average personal exposures to particulate matter (PM_2.5 and PM₁₀) and Mn. A stratified, three-stage, two-phase probability, longitudinal sample design of the metropolitan population was employed. Residential indoor and outdoor, and ambient levels (at a fixed site and on a roof) of PM_2.5, PM₁₀, and Mn were also measured. Supplementary data on traffic counts, meteorology, MMT levels in gasoline, personal occupations, and activities (e.g. amount of vehicular usage) were collected. Overall precision (%RSD) for analysis of duplicate co-located samples ranged from 2.5 to 5.0% for particulate matter and 3.1 to 5.5% for Mn. The detection limits were 1.47 and 3.45 μg m^-3 for the PM₁₀ and PM_2.5 fractions, respectively, and 5.50 and 1.83 ng m^-3 for Mn in PM₁₀ and PM_2.5, respectively. These low detection limits permitted the reporting of concentrations for >98% of the samples. For PM₁₀, the personal particulate matter levels (median 48.5 μg m^-3) were much higher than either indoor (23.1 μg m^-3) or outdoor levels (23.6 μg m^-3). The median levels for PM_2.5 for personal, indoor, and outdoor were 28.4, 15.4 and 13.2 μg m^-3, respectively. The correlation between PM_2.5 personal exposures and indoor concentrations was high (0.79), while correlations between personal and the outdoor, fixed site and roof site were low (0.16–0.27). Indoor Mn concentration distributions (in PM_2.5 and PM₁₀), unlike particulate matter, exhibited much lower and less variable levels that the corresponding outdoor data. The median personal exposure was 8.0 ng m^-3, compared with 4.7 and 8.6 ng m^-3, respectively, for the indoor and outdoor distributions. The highest correlations occurred for personal vs indoor data (0.56) and for outdoor vs roof site data (0.66), and vs fixed site data (0.56). The concentration of Mn in particulate matter, expressed in ppm (w/w), revealed that the fixed site was the highest, followed by the roof site, outdoor, indoor, and personal. The personal and indoor data showed a statistically significant correlation (0.68) while all other correlations between personal or indoor data and outdoor or fixed-site data were quite small. The low correlations of personal and indoor levels with outdoor levels suggest that different sources in the indoor and outdoor microenvironments produce particle matter with dissimilar composition. The correlation results indicate that neither the roof- nor fixed-site concentrations can adequately predict personal particulate matter or Mn exposures.     

Aerosol scattering properties in northern China

The aerosol scattering properties were investigated at two continental sites in northern China in 2004. Aerosol light scattering coefficient (σ_sp) at 525 nm, PM₁₀, and aerosol mass scattering efficiencies (α) at Dunhuang had a mean value of 165.1±148.8 M m⁻¹, 157.6±270.0 μg m⁻³, and 2.30±3.41 m² g⁻¹, respectively, while these values at Dongsheng were, respectively, 180.2±151.9 M m⁻¹, 119.0±112.9 μg m⁻³, and 1.87±1.41 m² g⁻¹. There existed a seasonal variability of aerosol scattering properties. In spring, at Dunhuang PM₁₀, σ_sp, and α were 184.1±211.548 μg m⁻³, 126.3±89.6 M m⁻¹, and 1.05±0.97 m² g⁻¹, respectively, and these values at Dongsheng were 146.4±142.1 μg m⁻³, 183.4±81.7 M m⁻¹, and 1.98±1.52 m² g⁻¹, respectively. However, in winter at Dunhuang PM₁₀, σ_sp, and α were 158.1±261.4 μg m⁻³, 303.3±165.2 M m⁻¹, and 3.17±1.93 m² g⁻¹, respectively, and these values at Dongsheng were 155.7±170.1 μg m⁻³, 304.4±158.1 M m⁻¹, and 2.90±1.72 m² g⁻¹, respectively. σ_sp and α in winter were higher than that in spring at both the sites, which coincides with the characteristics of dust aerosol and pollution aerosol. Overall, the dominant aerosol types in spring and winter at both sites in northern China are dust aerosol and pollution aerosol, respectively.     

Particulate size distributions and mass measured at a motorway during the BAB II campaign

From 1 May to 25 May 2001, the BAB II campaign was carried out at the motorway BAB (656) near Heidelberg. Atmospheric concentrations of particulate matter and gases were measured together with the meteorological conditions. This paper is focused on the particulate matter measured upwind and downwind from the motorway at ground level. In order to determine the source contribution from the motorway traffic, it was necessary to measure upwind and downwind simultaneously due to variations in background concentrations. The particle number contribution from the motorway was found to be 35,000 particles cm⁻³ for particles with diameters close to 20 nm and 5000 particles cm⁻³ for particles with diameters close to 70 nm. Bimodal size distributions were observed on the downwind side, whereas the upwind side showed unimodal size distributions. For particulate mass, it can be estimated that the contribution from the motorway to the PM₁ concentrations is in a range 0.6–1.3 μg m⁻³ for the chosen measurement sites approximately 60 m from the road at a height of 6 m. The soot measurements showed diurnal variation; however, the upwind downwind difference was not measured. Correlation factors showed good correlation between total particle number and number of particles with diameters below 80 nm, CO and NO. There was no correlation between particle number and PM₁₀, which is due to the observation that particle number was dominated by the 20 nm particles.