Role of Alternative Electron Acceptors (AEA) to control methane flux from waterlogged paddy fields: Case studies in the southern part of West Bengal, India

The rice fields, depleted of O₂, contain large amount of moisture and organic substrates to provide an ideal anaerobic environment for methanogenesis and are one of the principal anthropogenic sources of methane. In order to mitigate this emission Alternative Electron Acceptors (AEA) were altered in the soil. The experiments were carried out in four seasons at the site of Balarampur, near Baruipur, South 24 Parganas, West Bengal, namely September–December, 2005 (Cultivar: Sundari), February–May, 2006 (Cultivar: Sundari), September–December, 2006 and February–May, 2007 (Cultivar: Swarna-Pankaj). The seasonal average methane flux (Fe treated), for the cultivar type “Sundari” (season: September–December, 2005), is 4.41 t ha⁻¹, as compared to the value of 6.40 t ha⁻¹ for the untreated soil. Similarly for February–May, 2006, the seasonal average methane flux (Fe treated) is 5.52 t ha⁻¹, whereas the untreated flux is 5.69 t ha⁻¹. In the third and fourth seasons we had two treatments with Ammonium Thiosulphate and Ferric Hydroxide. The seasonal average methane flux (treatment: Ammonium Thiosulphate) is 4.35 t ha⁻¹ and 5.41 t ha⁻¹ respectively, whereas for the ferric hydroxide treated soil it is 4.35 t ha⁻¹ and 6.14 t ha⁻¹ respectively. The properties related to the nutrient quality of the harvested paddy seeds supplement these results.     

Assessment of Lead Exposure in Thohoyandou, South Africa

Lead levels in different environmental media (soil, grass leaves, water, ceramics, pencil, paint, crayons and cosmetics) were determined to assess the major sources of lead exposure in Thohoyandou, South Africa. Soil and plant leaves were used as indicators of Pb pollution from vehicle exhaust emissions. After digestion with concentrated acids (HNO₃, HCl and HClO₄) Pb concentrations were determined in triplicate using a flame atomic absorption spectrometer. The mean Pb concentrations at the kerb of selected busy roads were 205.5 ± 90, 273.0 ± 90 and 312.8 ± 81 μg g⁻¹ and 154.7 ± 67, 182.9 ± 76 and 240.6 ± 66 μg g⁻¹ for soil and plant leaves (dry weight) respectively. These concentrations were substantially higher than the values found on soils 50 m away from the roads (97.4 ± 11 μg g⁻¹). Pb concentrations in plants collected further away from the road (50 m) were substantially lower (71.8 ± 9.0 μg g⁻¹). The observed levels on soil are lower than the UK critical value of 500 μg g⁻¹ for gardens and allotments; and 2000 μg g⁻¹ for parks and open space as well as the Canadian values for agricultural (375 μg g⁻¹), residential (500 μg g⁻¹ and industrial (1000 μg g⁻¹). From these data it was clear that Pb concentrations in soil samples were substantially higher than the levels obtained for plant leaves. The Pb levels in green crayons, blue crayons, pencils (from China & Germany), were 10650 ± 75.2, 8200 ± 52.4, 1160 ± 50.2, 79 ± 10.1 μg g⁻¹ for the inner contents; and 4870 ± 58.1, 5650 ± 55.5, 1950 ± 46.6, 60 ± 12.9 μg g⁻¹ for the outer surface paint respectively. The ceramics showed Pb levels of 630 ± 50.3 μg g⁻¹ (saucer) and 560 ± 32.2 μg g⁻¹ (cup), while the inner contents and outer surface paint showed 480 ± 32.4 and 318 ± 21.2 μg g⁻¹ of Pb respectively. Early morning tap water flush gave a Pb level of 20.6 ± 5.6 μg Pb l⁻¹. This value is higher than the WHO and FDA maximum permissible concentrations of 10 μg l⁻¹ and 15 μg l⁻¹ respectively.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Growth and macronutrient removal of water hyacinth in a small secondary sewage treatment plant

Studies have been made of the growth characteristics of water hyacinth, Eichhornia crassipes (Mart.) Solms, and its ability to remove N, P and K, in a secondary settling pond of a small secondary sewage treatment plant serving both the academic and residential blocks of the Swire Marine Laboratory, University of Hong Kong. The treatment plant consists of, in series, a primary settling tank, a trickling filter compartment and a secondary settling pond from which part of the treated wastewater is recycled to the primary settling tank while the remaining effluent (1 to 2 m³ daily) mixes with and hence is diluted by the outflowing seawater from the aquarium system of the Swire Marine Laboratory before discharge to the sea. Samples of wastewater have been taken regularly from the primary sedimentation pond, the outflow of the trickling filter, the secondary settling pond and the effluent of the treatment plant (before mixing with aquarium outflow) since January, 1992. Physical, chemical and biological characteristics of the samples have been determined and are typical of secondary effluents, with a mean pH of about 7.5, total solids 1200 mg L⁻¹, suspended solids 45 mg L⁻¹, conductivity 2000 μS cm⁻¹, salinity 1 ppt, dissolved oxygen 2 mg L⁻¹, BOD₅ 45 mg L⁻¹, Kjeldahl-N 30 mg L⁻¹, NH₄,-N 25 mg L⁻¹, NO₃-N 4 mg L⁻¹, total P 10 mg L⁻¹, K 35 mg L⁻¹ and total coliforms of less than 10⁵ colonies 100 ml⁻¹.Water hyacinth plants have been stocked in the secondary settling pond as an integral part of the treatment plant so as to improve the quality of, as well as to retrieving and recycling nutrient elements from, the wastewater. The plants are periodically harvested to maintain an active growing crop. The growth rate, standing crop biomass, tissue nutrient composition, nutrient storage and accumulation rate of two growth cycles, one from February 25 to March 18 (mean temperature 17.6°C) and the other from 22 April to 12 May (24.8°C) are reported. The water hyacinth assumed a relatively high standing crop biomass of 10 kg m⁻² (5 to 6 t DM ha⁻¹), and growth rates of 48 and 225 g m⁻² day⁻¹, respectively, for the first and second growth period. Nutrient storage capacities were relatively high, at about 20, 7.5 and 16.5 g m⁻² for N, P and K, respectively. The nutrient composition was very high, reaching 5.42% for N, 1.97 for P, and 4.57 for K. Both the stem and lamina accumulated high levels of N, while the petiole had the highest level of P and K. Apart from nutrient removal, the water hyacinth also helped to decrease the suspended solids, BOD₅ value and total coliforms of the wastewater.It is concluded that water hyacinth improves the quality of wastewater in such small-scale sewage treatment plants and it is recommended that frequent harvests of water hyacinth would increase the treatment efficiency, especially during the active growing season with high temperatures coupled with intense solar radiation.     

Recycling of banana pseudostem waste for economical production of quality banana

Banana pseudostem biomass, traditionally incinerated and wasted, has been conserved and recycled by solid state fermentation (SSF) into plant growth stimulating soil conditioner (SC). This SC alone or combined with biofertilizers showed reduced mortality (10 and 12%) of planted suckers, enhanced chlorophyll contents (593 and 661 μg g⁻¹), gave biomass (35.0 and 36.6 kg) at par and improved yield (54.2 and 55.0 MT ha⁻¹), with that of the control (23%, 312 μg g⁻¹, 36.3 kg and 49.4 MT ha⁻¹, respectively). This has afforded (i) saving of chemical fertilizers by 50%, (ii) reduction in quantum (40%) and frequency (15%) of irrigation and (iii) reduction in cost of electricity and labor without sacrificing quality and quantity of banana. Thus, a voluminous agro-waste is converted into an eco-friendly agro-input for sustainable productivity.     

Three Egyptian industrial wastewater management programmes

A pre-treatment programme for wastewater from factories, representing three main industrial sectors in Egypt, has been developed. The first case study was a factory producing potato-chips. Wastewater discharged from this factory was characterized by high values of BOD, SS and oil and grease (6000 mgO₂ l^–1, 6577 mg l^–1 and 119 mg l^–1 respectively). Chemical treatment using lime and lime aided by polyelectrolyte achieved good results. Residual values of BOD and SS after treatment were 97 mg l^–1 and 49 mg l^–1, respectively. Oil and grease concentrations were reduced by 91 percent. Treatment via activated sludge at a detention time of 4 hrs produced good quality effluent. The second case study was an automobile company, representing the metal finishing industry. Analyses of wastewater samples from the degreasing, phosphating and painting departments, as well as the end-of-pipe effluent were conducted. The end-of-pipe effluent contained high concentrations of oil and grease (366 mg l^–1), phosphorous (111 mg l^–1) and zinc (81 mg l^–1). Chemical treatment of end-of-pipe wastewater using ferric chloride aided by lime, produced high quality effluent. The third sector was the chemical industry. For this purpose a paint factory was selected. Characteristics of raw wastewater varied widely according to the production rate. Average values of COD and BOD were 1950 mg l^–1 and 683 mg l^–1. Oil and grease ranged from 63 to 1624 mg l^–1. Chemical treatment using ferric chloride in combination with lime at the optimum operating conditions achieved good results. Residual values after treatment of COD, BOD and oil and grease reached 120, 36 and 8.6 mg l^–1, respectively. An engineering design for each case study has been prepared.     

Utilization of pulp and paper industrial wastes to remove heavy metals from metal finishing wastewater

Two pulp and paper industrial wastes, lime mud (LM) and recovery boiler ash (RB), have low moisture contents, low heavy metal contaminations and contain various carbonate compounds which contribute to a high pH. Metal finishing wastewater (MF-WW) has a low pH, high levels of TDS and high contaminations from Cr, Cu, Pb and Zn. The heavy metals from MF-WW were removed by sorption and precipitation mechanisms. LM gave better results in removing heavy metals from MF-WW than RB. At a reaction time of 45 min, the maximum removal efficiencies for Cr (93%) and Cu (99%) were obtained at 110 g L⁻¹ of LM, but at 80 g L⁻¹ for Pb (96%) and Zn (99%). Treatment with LM gives a higher sludge volume than with RB. However, the leachability of heavy metals from LM is lower. Leachability of heavy metals in the sediment for all selected treatment conditions is within government standards.     

Unexpected difference in phenol sorption on PTMA- and BTMA-bentonite

The comparison of phenol sorption on phenyltrimethylammonium (PTMA)- and benzyltrimethylammonium (BTMA)-bentonite shows a clear difference as far as phenol sorption isotherms are concerned. For PTMA-bentonite the sorption isotherm is of a straight-line character which results from simple partitioning of phenol between the aqueous and organic phases sorbed on the bentonite surface. For BTMA-bentonite the isotherm has a convex shape, characteristic of physicochemical sorption.For the first time a three-parametric model, including the dissociation constant of phenol pK_a, distribution constant of phenol Kd_phen and phenolate anion Kd_phen⁻ between the aqueous phase and the bentonite phases is used for the evaluation of phenol sorption on organoclays with pH change. The model shows that the values of Kd_phen are higher than those of Kd_phen⁻ for all investigated initial phenol concentrations.The inspection of the FTIR spectrum of BTMA-bentonite loaded with phenol in the regions 1300–1600 and 1620–1680 cm⁻¹ shows the features of π–π electron interaction between the benzene rings of phenol and the BTMA cation together with the phenol–water hydrogen bond strengthened by this interaction.     

Biosorption of Cu and Zn from aqueous solutions by dried marine green macroalga Chaetomorpha linum

The biosorption of the heavy metals Cu²⁺ and Zn²⁺ by dried marine green macroalga (Chaetomorpha linum) was investigated. The biosorption capacities of the dried alga for copper and zinc were studied at different solution pH values (2–6), different algal particle sizes (100–800 μm) and different initial metal solution concentrations (0.5–10 mM). An optimum pH value of 5 was found suitable for both metal ions biosorption for both metal ions. At the optimum particle size (100–315 μm), biosorbent dosage (20 g/l) and initial solution pH (pH 5), the dried alga produced maximum copper and zinc uptakes values (q_max) of 1.46 and 1.97 mmol/g respectively (according to the Langmuir model). The kinetic data obtained at different initial metal concentrations indicated that the biosorption rate was fast and most of the process was completed within 120 min. This study illustrated an alternative technique for the management of unwanted biological materials using processed algal material. C. linum is one of the fast-growing marine algae in the lake of Tunis and could be utilized as a biosorbent for the treatment of Cu²⁺ and Zn²⁺ contaminated wastewater streams.     

160 h of chemical-looping combustion in a 10 kW reactor system with a NiO-based oxygen carrier

Chemical-looping combustion, CLC, is a technology with inherent separation of the greenhouse gas CO₂. The technique uses an oxygen carrier made up of particulate metal oxide to transfer oxygen from combustion air to fuel. In this work, an oxygen carrier consisting of 60% NiO and 40% NiAl₂O₄ was used in a 10 kW CLC reactor system for 160 h of operation with fuel. The first 3 h of fuel operation excepted, the test series was accomplished with the same batch of oxygen carrier particles. The fuel used in the experiments was natural gas, and a fuel conversion to CO₂ of approximately 99% was accomplished. Combustion conditions were very stable during the test period, except for the operation at sub-stoichiometric conditions. It was shown that the methane fraction in the fuel reactor exit gas was dependent upon the rate of solids circulation, with higher circulation leading to more unconverted methane. The carbon monoxide fraction was found to follow the thermodynamical equilibrium for all investigated fuel reactor temperatures, 660–950 °C. Thermal analysis of the fuel reactor at stable conditions enabled calculation of the particle circulation which was found to be approximately 4 kg/s, MW. The loss of fines, i.e. the amount of elutriated oxygen carrier particles with diameter <45 μm, decreased during the entire test period. After 160 h of operation the fractional loss of fines was 0.00022 h⁻¹, corresponding to a particle life time of 4500 h.     

Antibacterial behavior of silver-modified clinoptilolite-heulandite rich tuff on coliform microorganisms from wastewater in a column system

The water disinfecting behavior of silver-modified clinoptilolite–heulandite rich tuff (ZSAg) as an antibacterial agent against coliform microorganisms from water in a continuous mode was investigated. Silver recovery from the disinfected effluents by the sodium-modified clinoptilolite–heulandite rich tuff (ZSNa) was also considered. Escherichia coli (ATCC 8739) and total coliform microorganisms, as indicators of microbiological contamination of water, were chosen to achieve the disinfection of synthetic wastewater or municipal wastewater. Ammonium (NH₄⁺) and chloride (Cl⁻) ions were added to the synthetic wastewater as an interfering chemical species on the disinfection processes. The antibacterial activity of the ZSAg as a bactericide was measured by the coliform concentration as evaluated by the APHA method. The amount of silver in the disinfected effluents was determined using atomic absorption spectroscopy. The inactivation of the ZSAg was calculated from the breakthrough curves based on the model reported by Gupta et al. It was found that when the silver concentration in the effluent is less than 0.6 μg/mL, the bacterial survival percentage increased and the volume of disinfected water diminished. The total silver amounts found in the effluent at the end of the disinfection processes varied depending on the water treated (synthetic or municipal wastewater). The presence of NH₄⁺ ions in synthetic wastewater influent notably improved the disinfected water volume (zero NVC/100 mL), in comparison to the disinfection of the same influent without NH₄⁺ ions. A contrary water disinfection behavior was observed in the presence of Cl⁻ ions. The silver recovery does not depend on the mass of the sodium zeolitic bed according with the wastewater to be treated (synthetic or municipal wastewater) and the presence of NH₄⁺ or Cl⁻ ions in the influent also influenced the silver recovery from wastewater. The ZSNa did not have antibacterial activity. Therefore the amount of bactericide agent (silver-modified natural zeolite), coliform microorganisms from water (E. coli or consort of coliform microorganisms) as well as the water quality (synthetic wastewater or municipal wastewater) influenced both the disinfection process and the silver recovery in a column system.     

Model prediction on the rise of pCO2 in uniform flows by leakage of CO2 purposefully stored under the seabed

A numerical study was conducted to predict pCO₂ change in the ocean on a continental shelf by the leakage of CO₂, which is originally stored in the aquifer under the seabed, in the case that a large fault connects the CO₂ reservoir and the seabed by an earthquake or other diastrophism. The leakage rate was set to be 6.025 × 10⁻⁴ kg/m²/sec from 2 m × 100 m fault band, which corresponds to 3800 t-CO₂/year, referring to the monitored seepage rate from an existing EOR field. The target space in this study was limited to the ocean above the seabed, the depth of which was 200 or 500 m. The computational domain was idealistically rectangular with the seabed fault-band perpendicular to the uniform flow. The CO₂ takes a form of bubbles or droplets, depending on the depth of water, and their behaviour and dissolution were numerically simulated during their rise in seawater flow. The advection–diffusion of dissolved CO₂ was also simulated. As a result, it was suggested that the leaked CO₂ droplets/bubbles all dissolve in the seawater before spouting up to the atmosphere, and that the increase in pCO₂ in the seawater was smaller than 500 μ atm.     

Periodical monitoring with lichen, <Emphasis Type="Italic">Phaeophyscia hispidula</Emphasis> (Ach.) Moberg in Dehradun city,Uttarakhand, India

Nine heavy metals were estimated in lichen, Phaeophyscia hispidula (Ach.) Moberg, collected from 12 different sites of Dehradun, capital city, to analyze the air quality of Uttarakhand. Total metal concentration was the highest at Mohkampur Railway Crossing, Hardwar Road (42,505 μg g⁻¹). Dela Ram Chowk, located in the center of the city, also had higher metal concentration, 34,317 μg g⁻¹, with maximum concentration of Pb at 12,433 μg g⁻¹, while Nalapani forest area had minimum total metal concentration (1,873 μg g⁻¹) as well as minimum Pb level at 66.6 μg g⁻¹, indicating anthropogenic activity, mainly vehicular activity, responsible for the increase in metal concentration in the ambient environment. In comparison with the earlier years 2004 and 2006, air pollution as indicated by similar lichen shows a considerable increase in the total metal concentration (especially Pb) in the ambient air of Dehradun city, which may be attributed to exponential rise in the traffic activity in the last 5 years.     

Factors affecting nitrate distribution in shallow groundwater under a beef farm in South Eastern Ireland

Groundwater contamination was characterised using a methodology which combines shallow groundwater geochemistry data from 17 piezometers over a 2 yr period in a statistical framework and hydrogeological techniques. Nitrate–N (NO₃-N) contaminant mass flux was calculated across three control planes (rows of piezometers) in six isolated plots. Results showed natural attenuation occurs on site although the method does not directly differentiate between dilution and denitrification. It was further investigated whether NO₃-N concentration in shallow groundwater (<5 m below ground level) generated from an agricultural point source on a 4.2 ha site on a beef farm in SE Ireland could be predicted from saturated hydraulic conductivity (K_sat) measurements, ground elevation (m Above Ordnance Datum), elevation of groundwater sampling (screen opening interval) (m AOD) and distance from a dirty water point pollution source. Tobit regression, using a background concentration threshold of 2.6 mg NO₃-N L⁻¹ showed, when assessed individually in a step wise procedure, K_sat was significantly related to groundwater NO₃-N concentration. Distance of the point dirty water pollution source becomes significant when included with K_sat in the model. The model relationships show areas with higher K_sat values have less time for denitrification to occur, whereas lower K_sat values allow denitrification to occur. Areas with higher permeability transport greater NO₃-N fluxes to ground and surface waters. When the distribution of Cl⁻ was examined by the model, K_sat and ground elevation had the most explanatory power but K_sat was not significant pointing to dilution having an effect. Areas with low NO₃ concentration and unaffected Cl⁻ concentration points to denitrification, low NO₃ concentration and low Cl⁻ chloride concentration points to dilution and combining these findings allows areas of denitrification and dilution to be inferred. The effect of denitrification is further supported as mean groundwater NO₃-N was significantly (P < 0.05) related to groundwater N₂/Ar ratio, redox potential (Eh), dissolved O₂ and N₂ and was close to being significant with N₂O (P = 0.08). Calculating contaminant mass flux across more than one control plane is a useful tool to monitor natural attenuation. This tool allows the identification of hot spot areas where intervention other than natural attenuation may be needed to protect receptors.     

Comparison of biosorbents with inorganic sorbents for removing copper(II) from aqueous solutions

In comparison with several other reported inorganic sorbents, Camellia tree leaf and primary sludge obtained from a settling tank as a pretreatment to the activated sludge system in a Hong Kong sewage treatment plant were evaluated for removing Cu(II) from aqueous solutions. Experimental data were modeled by the Langmuir isotherm equation to estimate the maximum sorption capacity (q_max). Results show that, at pH 5.6, biosorbents, Camellia tree leaf and primary sludge in particular, exert higher sorption capacities (q_max > 40 mg g⁻¹) than inorganic sorbents, Na-montmorillonite (q_max = 33.3 mg g⁻¹), fly ash (q_max = 18.8 mg g⁻¹), and goethite powder (10.3 mg g⁻¹). Furthermore, a pseudo second-order kinetic model was found to properly describe the experimental data for both bio- and inorganic sorbents. Sorption of Cu(II) on the Camellia tree leaf and primary sludge were much faster than that on the inorganic sorbents. In addition, desorption tests revealed that the desorption capacities of the two biomaterials are higher than the other selected materials; and much more Cu(II) can be retrieved from the Cu(II)-loaded biosorbents. Finally, increasing solution pH was found to greatly increase q_max and accelerate sorption processes.     

Recovery of phosphate from calcinated bone by dissolution in hydrochloric acid solutions

In this study, the optimum conditions of dissolution of calcinated bone in HCl solutions with different concentrations are investigated. Recovery of phosphate from calcinated bone by dissolution with hydrochloric acid solutions was investigated in a batch reactor, it was observed that a 32% hydrochloric acid solution can dissolve the calcinated bone effectively. Using the Taguchi fractional design method, it was found that the optimum process conditions, at which 67.2% P₂O₅ dissolution was reached, were as follows: Reaction temperature: 318 K, solid-to-liquid ratio: 1/5 (g ml⁻¹), acid concentrations:32 (% w/v), stirring speed:400 min⁻¹ and reaction time: 60 min.     

Kinetics of carbon dioxide absorption into mixed aqueous solutions of MDEA and MEA using a laminar jet apparatus and a numerically solved 2D absorption rate/kinetics model

New comprehensive numerically solved 1D and 2D absorption rate/kinetics models have been developed, for the first time, to interpret the experimental kinetic data obtained with a laminar jet apparatus for the absorption of carbon dioxide (CO₂) in CO₂ loaded mixed solutions of mixed amine system of methyldiethanolamine (MDEA) and monoethanolamine (MEA). Three MDEA/MEA weight ratios ranging from 27/03 to 23/07, over a concentration range of 2.316–1.996 kmol/m³ for MDEA and of 0.490–1.147 kmol/m³ for MEA were studied. The models take into account the coupling between chemical equilibrium, mass transfer, and the chemical kinetics of all possible chemical reactions involved in the CO₂ reaction with MDEA/MEA solvent. The partial differential equations of the 1D model were solved by two numerical techniques; the finite difference method (FDM) based on in-house coded Barakat–Clark scheme and the finite element method (FEM) based on COMSOL software. The FEM comprehensive model was then used to solve the set of partial differential equations in the 2D cylindrical coordinate system setting. Both FDM and FEM produced very accurate results for both the 1D and 2D models, which were much better than our previously published simplified model. The reaction rate constant obtained for MEA blended into MDEA at 298–333 K was k_MEA = 5.127 × 10⁸ exp(−3373.8/T). In addition, the 2D model, for the first time, has provided the concentration profiles of all the species in both the radial and axial directions of the laminar jet, thereby enabling an understanding of the correct sequence in which the reaction steps involved in the reactive absorption of CO₂ in aqueous mixed amines occur.     

Batch and continuous biosorption of Cu by immobilized biomass of Arthrobacter sp.

The ability of free and polysulphone immobilized biomass of Arthrobacter sp. to remove Cu²⁺ ions from aqueous solution was studied in batch and continuous systems. The Langmuir and Freundlich isotherm models were applied to the data. The Langmuir isotherm model was found to fit the sorption data indicating that sorption was monolayer and uptake capacity (Q^o) was 175.87 and 158.7 mg/g for free and immobilized biomass respectively at pH 5.0 and 30 °C temperature, which was also confirmed by a high correlation coefficient, a low RMSE and a low Chi-square value. A kinetic study was carried out with pseudo-first-order reaction and pseudo-second-order reaction equations and it was found that the Cu²⁺ uptake process followed the pseudo-second-order rate expression. The diffusivity of Cu²⁺ on immobilized beads increased (0.402 × 10⁻⁴ to 0.435 × 10⁻⁴ cm²/s) with increasing concentration from 50 to 150 mg/L. The maximum percentage Cu²⁺ removal (89.56%) and uptake (32.64 mg/g) were found at 3.5 mL/min and 20 cm bed height. In addition to this the Bed Depth Service Time (BDST) model was in good agreement with the experimental data with a high correlation coefficient (>0.995). Furthermore, sorption and desorption studies were also carried out which showed that polysulphone immobilized biomass could be reused for up to six sorption–desorption cycles.     

Aerosol chemistry and the effect of aerosol water content on visibility impairment and radiative forcing in Guangzhou during the 2006 Pearl River Delta campaign

Optical and chemical aerosol measurements were obtained from 2 to 31 July 2006 at an urban site in the metropolitan area of Guangzhou (China) as part of the Program of Regional Integrated Experiment of Air Quality over Pearl River Delta (PRIDE-PRD2006) to investigate aerosol chemistry and the effect of aerosol water content on visibility impairment and radiative forcing. During the PRIDE-PRD2006 campaign, the average contributions of ammonium sulfate, organic mass by carbon (OMC), elemental carbon (EC), and sea salt (SS) to total PM_2.5 mass were measured to be 36.5%, 5.7%, 27.1%, 7.8%, and 3.7%, respectively. Compared with the clean marine period, (NH₄)₂SO₄, NH₄NO₃, and OMC were all greatly enhanced (by up to 430%) during local haze periods via the accumulation of a secondary aerosol component. The OMC dominance increased when high levels of biomass burning influenced the measurement site while (NH₄)₂SO₄ and OMC did when both biomass burning and industrial emissions influenced it. The effect of aerosol water content on the total light-extinction coefficient was estimated to be 34.2%, of which 25.8% was due to aerosol water in (NH₄)₂SO₄, 5.1% that in NH₄NO₃, and 3.3% that in SS. The average mass-scattering efficiency (MSE) of PM₁₀ particles was determined to be 2.2 ± 0.6 and 4.6 ± 1.7 m² g⁻¹ under dry (RH < 40%) and ambient conditions, respectively. The average single-scattering albedo (SSA) was 0.80 ± 0.08 and 0.90 ± 0.04 under dry and ambient conditions, respectively. Not only are the extinction and scattering coefficients greatly enhanced by aerosol water content, but MSE and SSA are also highly sensitive. It can be concluded that sulfate and carbonaceous aerosol, as well as aerosol water content, play important roles in the processes that determine visibility impairment and radiative forcing in the ambient atmosphere of the Guangzhou urban area.     

Enrichment of vermicomposts prepared from cow dung spiked solid textile mill sludge using nitrogen fixing and phosphate solubilizing bacteria

Textile mill waste can be vermicomposted if it is mixed in the range of 20–30% with cow dung. This article reports the effect of inoculation, of nitrogen fixing Azotobacter chroococcum strain; Azospirillum brasilense strain and phosphate solubilizing Pseudomonas maltophila, on nitrogen and phosphorus content of vermicomposts prepared from cow dung (CD) and cow dung spiked textile mill sludge (CD + STMS). The CD vermicompost was more supportive to the growth and multiplication of all the three bacteria than CD + STMS vermicompost. In Azotobacter chroococcum treated vermicomposts maximum nitrogen content was recorded between 45 and 60 days [CD␣vermicompost (25.9 ± 0.45 g kg⁻¹) and CD + STMS vermicompost (20.6 ± 0.62 g kg⁻¹)] followed by Azospirillum brasilense inoculation [CD vermicompost (19.4 ± 0.60 g kg⁻¹) and CD + STMS vermicompost (18.6 ± 0.17 g kg⁻¹)]. Phosphorus content in Pseudomonas maltophila inoculated CD vermicompost was 20.8 ± 0.20 g kg⁻¹ and CD + STMS vermicompost was 13.4 ± 0.45 g kg⁻¹ after 75th day of inoculation.