Study on the quality and stability of compost through a Demo Compost Plant

This study is concerned with the performance of a Demo Compost Plant for the development of acceptable composting technology in Bangladesh. The Demo Compost Plant was setup at the adjacent area of an existing compost plant located at Khulna city in Bangladesh. Four different composting technologies were considered, where Municipal Solid Waste (MSW) were used as a raw material for composting, collected from the adjacent areas of the plant. Initially the whole composting system was conducted through two experimental setups. In the 1st setup three different types of aerators (horizontal and vertical passively aerator and forced aerator) were selected. For a necessary observation four piles, using only MSW as the input materials in the first three compost pile, the fourth one was the existing Samadhan’s compost pile. Based on the analysis of the experimental findings, the horizontal passively aerated composting technique is suitable for Bangladesh as it had better performance for reducing composting period than that of the others. It was being observed from the quality parameters of compost in the both 1st and 2nd setup that as the waste directly come from kitchen, degradation rate of waste shows a positive result for reducing this waste and there is no possibility of toxic contamination, when it would be used as a soil conditioner. Though there is no significant improvement in the quality of the final product in the 2nd setup as comparing with the 1st setup but it fulfills one of the main objectives of this study is to reduce the whole composting period as well as immediate management of the increasing amount of waste and reducing load on landfill. Selfheating tests reveal that degree of stability of compost with respect to maturation period was remained in the acceptable level, which was further accelerated due to the use of organic additives.     

Bioremediation of contaminated soil and sediment by composting

There are many well‐established bioremediation technologies applied commercially at contaminated sites. One such technology is the use of compost material. Composting matrices and composts are rich sources of microorganisms, which can degrade contaminants to innocuous compounds such as carbon dioxide and water. In this article, composting of contaminated soil and sediment was performed on a laboratory bench‐scale pile. Fertilizer was added to increase the nutrient content, and the addition of commercial compost provided a rich source of microorganisms. After maintaining proper composting conditions, the feasibility of composting was assessed by monitoring pH, total volatile solids, total microbial count, temperature, and organic contaminant concentration. The entire composting process occurred over a period of five weeks and resulted in the degradation of contaminants and production of compost with a high nutritional content that could be further used as inocula for the treatment of hazardous waste sites. © 2006 Wiley Periodicals, Inc.     

Effect of the composting substrate on biodegradation of solid materials under controlled composting conditions

Biodegradability under composting conditions is assessed by test methods, such as ASTM D 5338-92, based on the measurement of CO₂ released by test materials when mixed with mature compost and maintained in a controlled composting environment. However, in real composting, biodegradation occurs in fresh waste. To clarify this point, the biodegradation of paper and of a starch-based biodegradable thermoplastic material, Mater-Bi ZI01U, was followed by measuring the weight loss of samples introduced either into a mature compost or into a synthetic waste. The weight loss in mature compost was higher at the beginning but tended to decrease; in synthetic waste a first lag phase was followed by an exponential phase. Complete degradation of paper was noticed simultaneously in the two substrates (after 25 days). The bulkier Mater-Bi samples were fully degraded after 20 days in fresh waste, but after 45 days in mature compost. Therefore, the test methods using mature compost as a substrate can possibly underestimate the biodegradation rate occurring in fresh waste, i.e., in real composting plants, and have to be considered as conservative test methods. The test procedure described in this paper seems very suitable as a screening method to verify the compostability of plastic materials in a composting environment.     

Recycling of waste biomass and mineral powder for preparation of potassium-enriched compost

An attempt was made to recycle waste biomass and mineral powder (waste mica) as an alternative source of potassium (K) through composting technology. Two different waste biomass, isabgol straw and palmarosa distillation waste along with two levels of waste mica (2 and 4% as K) were used for preparation of enriched composts. A notable decrease of C:N ratio was observed at the end of the composting (150 days) as an indicator of compost maturity. The mature composts were evaluated for K-supplying capacity through laboratory leaching and soil incubation study. Significantly higher water-soluble K released initially followed by a sharp decrease up to 21 days of leaching thereafter gradually decreased up to 35 days of leaching. Water-soluble K was released from K-enriched (mica charged) compost significantly higher than the ordinary compost throughout the leaching period. Soil incubation study also revealed that application of K-enriched compost greatly improved the available K (water soluble and exchangeable) pools in K-deficient soil which indicated that a considerable amount of K releases during composting. Therefore, K-enriched compost could be an effective alternative of costly commercial K fertilizer and eco-friendly approach to utilize low-cost waste mineral powder and plant residue.     

Effects of alkyl polyglycoside (APG) on composting of agricultural wastes

Composting is the biological degradation and transformation of organic materials under controlled conditions to promote aerobic decomposition. To find effective ways to accelerate composting and improve compost quality, numerous methods including additive addition, inoculation of microorganisms, and the use of biosurfactants have been explored. Studies have shown that biosurfactant addition provides more favorable conditions for microorganism growth, thereby accelerating the composting process. However, biosurfactants have limited applications because they are expensive and their use in composting and microbial fertilizers is prohibited. Meanwhile, alkyl polyglycoside (APG) is considered a “green” surfactant. This study aims to determine whether APG addition into a compost reaction vessel during 28-day composting can enhance the organic matter degradation and composting process of dairy manure. Samples were periodically taken from different reactor depths at 0, 3, 5, 7, 14, 21, and 28 days. pH levels, electrical conductivity (EC), ammonium and nitrate nitrogen, seed germination indices, and microbial population were determined. Organic matter and total nitrogen were also measured.Compared with the untreated control, the sample with APG exhibited slightly increased microbial populations, such as bacteria, fungi, and actinomycetes. APG addition increased temperatures without substantially affecting compost pH and EC throughout the process. After 28 days, APG addition increased nitrate nitrogen concentrations, promoted matter degradation, and increased seed germination indices. The results of this study suggest that the addition of APG provides more favorable conditions for microorganism growth, slightly enhancing organic matter decomposition and accelerating the composting process, improving the compost quality to a certain extent.     

Changes in the microbial communities during co-composting of digestates

Anaerobic digestion is a waste treatment method which is of increasing interest worldwide. At the end of the process, a digestate remains, which can gain added value by being composted. A study was conducted in order to investigate microbial community dynamics during the composting process of a mixture of anaerobic digestate (derived from the anaerobic digestion of municipal food waste), green wastes and a screened compost (green waste/kitchen waste compost), using the COMPOCHIP microarray. The composting process showed a typical temperature development, and the highest degradation rates occurred during the first 14 days of composting, as seen from the elevated CO₂ content in the exhaust air. With an exception of elevated nitrite and nitrate levels in the day 34 samples, physical–chemical parameters for all compost samples collected during the 63 day process indicated typical composting conditions. The microbial communities changed over the 63 days of composting. According to principal component analysis of the COMPOCHIP microarray results, compost samples from the start of the experiment were found to cluster most closely with the digestate and screened compost samples. The green waste samples were found to group separately. All starting materials investigated were found to yield fewer and lower signals when compared to the samples collected during the composting experiment.     

Enzymatic hydrolysis of organic waste materials in a solid-liquid system

In the current climate of increasing emphasis on environmental protection and efficient waste management, regional management bodies and environmental agencies are striving to achieve an economical and environmentally acceptable system for the recycling of biodegradable organic wastes. Composting would appear to be a cost effective solution to this problem, but in its entirety, composting is an inherently lengthy and variable process and is restrictive in terms of the demand on resources and space in composting plants. The aim of this study was to compare a biological composting process of solid residues with an enzymatic hydrolysis process of residues. The length of time required to naturally compost three organic materials, spent mushroom compost (SMC), farmyard manure (FYM) and dairy wastewater sludge (DWS) under optimal conditions was 42 days, 98 days and 84 days, respectively. In an attempt to accelerate this process, commercial enzymes were added to the waste products in a heterogeneous solid-liquid system. The enzymes utilised included a range of proteases, cellulases, ligninases, lipases and pectinases, which are responsible for the hydrolysis of protein, cellulose, lignin, lipids and carbohydrates, respectively. Preliminary results indicate that all of the organic materials were stabilised within 9h and that the enzymes used would, therefore, improve the efficiency of a waste management plant, if such a system were employed. Spent mushroom compost has a mean N/P/K ratio of 20:10:10 recorded for composted SMC, while a similar ratio of 20:10:20 was obtained for hydrolysed SMC. In contrast, composted farmyard manure has a N/P/K ratio of 30:0:30 and a ratio of 10:1:10 for hydrolysed FYM. Finally, composted DWS has a N/P/K ratio of 20:1:30 while DWS hydrolysate has a N/P/K ratio of 40:1:20, with the decrease in nitrogen in the composted DWS attributed to the addition of wood chippings and sawdust as a bulking agent. While all three materials have a considerable supply of plant nutrients, the variability in nutrients could be overlooked when employed as a soil amendment.     

Mass and element balance in food waste composting facilities

The mass and element balance in municipal solid waste composting facilities that handle food waste was studied. Material samples from the facilities were analyzed for moisture, ash, carbon, nitrogen, and the oxygen consumption of compost and bulking material was determined.Three different processes were used in the food waste composting facilities: standard in-vessel composting, drying, and stand-alone composting machine. Satisfactory results were obtained for the input/output ash balance despite several assumptions made concerning the quantities involved. The carbon/nitrogen ratio and oxygen consumption values for compost derived only from food waste were estimated by excluding the contribution of the bulking material remaining in the compost product. These estimates seemed to be suitable indices for the biological stability of compost because there was a good correlation between them, and because the values seemed logical given the operating conditions at the facilities.     

Dynamic of functional microbial groups during mesophilic composting of agro-industrial wastes and free-living (N2)-fixing bacteria application

Although several reports are available concerning the composition and dynamics of the microflora during the composting of municipal solid wastes, little is known about the microbial diversity during the composting of agro-industrial refuse. For this reason, the first parts of this study included the quantification of microbial generic groups and of the main functional groups of C and N cycle during composting of agro-industrial refuse. After a generalized decrease observed during the initial phases, a new bacterial growth was observed in the final phase of the process. Ammonifiers and (N₂)-fixing aerobic groups predominated outside of the piles whereas, nitrate-reducing group increased inside the piles during the first 23 days of composting. Ammonia-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria (NOB), showed an opposite trend of growth since ammonia oxidation decreased with the increase of the nitrite oxidation activity. Pectinolytics, amylolytics and aerobic cellulolytic were present in greater quantities and showed an upward trend in both the internal and external part of the heaps.Several free-living (N₂)-fixing bacteria were molecularly identify as belonging especially to uncommon genera of nitrogen-fixing bacteria as Stenotrophomonas, Xanthomonas, Pseudomonas, Klebsiella, Alcaligenes, Achromobacter and Caulobacter. They were investigated for their ability to fix atmospheric nitrogen to employ as improvers of quality of compost. Some strains of Azotobacter chrococcum and Azotobacter salinestris were also tested. When different diazotrophic bacterial species were added in compost, the increase of total N ranged from 16% to 27% depending on the selected microbial strain being used. Such microorganisms may be used alone or in mixtures to provide an allocation of plant growth promoting rhizobacteria in soil.     

Composting in small laboratory pilots: performance and reproducibility

Small-scale reactors (<10 l) have been employed in composting research, but few attempts have assessed the performance of composting considering the transformations of organic matter. Moreover, composting at small scales is often performed by imposing a fixed temperature, thus creating artificial conditions, and the reproducibility of composting has rarely been reported. The objectives of this study are to design an innovative small-scale composting device safeguarding self-heating to drive the composting process and to assess the performance and reproducibility of composting in small-scale pilots. The experimental setup included six 4-l reactors used for composting a mixture of sewage sludge and green wastes. The performance of the process was assessed by monitoring the temperature, O₂ consumption and CO₂ emissions, and characterising the biochemical evolution of organic matter. A good reproducibility was found for the six replicates with coefficients of variation for all parameters generally lower than 19%. An intense self-heating ensured the existence of a spontaneous thermophilic phase in all reactors. The average loss of total organic matter (TOM) was 46% of the initial content. Compared to the initial mixture, the hot water soluble fraction decreased by 62%, the hemicellulose-like fraction by 68%, the cellulose-like fraction by 50% and the lignin-like fractions by 12% in the final compost. The TOM losses, compost stabilisation and evolution of the biochemical fractions were similar to observed in large reactors or on-site experiments, excluding the lignin degradation, which was less important than in full-scale systems. The reproducibility of the process and the quality of the final compost make it possible to propose the use of this experimental device for research requiring a mass reduction of the initial composted waste mixtures.     

Assessment of microbiological and parasitological quality of composted wastes: health implications and hygienic measures.

Feedstock and compost samples were collected from twenty composting plants and analysed from the microbiological point of view. Faecal indicator organisms were determined in order to evaluate the efficacy of processes for the removal of pathogenic micro-organisms with similar survival characteristics and to verify their suitability as appropriate markers of microbial quality of composted products. In addition to the classical bacterial indicators, selected organisms, such as Salmonella, Giardia, Cryptosporidium, Clostridium spores and helminth ova, were investigated. Statistically significant differences in the removal of the different micro-organisms were observed with regard to both the different composting plants (P < 0.05) and feedstock composition (P < 0.05). In fact, compost obtained by feedstock containing sewage sludge was shown to have a better hygienic quality in comparison with compost containing green discards and municipal solid waste as raw matter. Giardia cysts, Cryptosporidium oocysts and helminth ova were not effective indicators of hygienic quality of compost, whereas Clostridium perfringens spores, because of their high resistance to treatments, could be considered as an additional model for assessing the composting process, especially with regard to more resistant pathogen reduction.     

Aerobic composting of waste activated sludge: kinetic analysis for microbiological reaction and oxygen consumption

In order to examine the optimal design and operating parameters, kinetics for microbiological reaction and oxygen consumption in composting of waste activated sludge were quantitatively examined. A series of experiments was conducted to discuss the optimal operating parameters for aerobic composting of waste activated sludge obtained from Kawagoe City Wastewater Treatment Plant (Saitama, Japan) using 4 and 20 L laboratory scale bioreactors. Aeration rate, compositions of compost mixture and height of compost pile were investigated as main design and operating parameters. The optimal aerobic composting of waste activated sludge was found at the aeration rate of 2.0 L/min/kg (initial composting mixture dry weight). A compost pile up to 0.5 m could be operated effectively. A simple model for composting of waste activated sludge in a composting reactor was developed by assuming that a solid phase of compost mixture is well mixed and the kinetics for microbiological reaction is represented by a Monod-type equation. The model predictions could fit the experimental data for decomposition of waste activated sludge with an average deviation of 2.14%. Oxygen consumption during composting was also examined using a simplified model in which the oxygen consumption was represented by a Monod-type equation and the axial distribution of oxygen concentration in the composting pile was described by a plug-flow model. The predictions could satisfactorily simulate the experiment results for the average maximum oxygen consumption rate during aerobic composting with an average deviation of 7.4%.     

Mass balances and life cycle inventory of home composting of organic waste

A comprehensive experimental setup with six single-family home composting units was monitored during 1 year. The composting units were fed with 2.6-3.5 kg organic household waste (OHW) per unit per week. All relevant consumptions and emissions of environmental relevance were addressed and a full life-cycle inventory (LCI) was established for the six home composting units. No water, electricity or fuel was used during composting, so the major environmental burdens were gaseous emissions to air and emissions via leachate. The loss of carbon (C) during composting was 63-77% in the six composting units. The carbon dioxide (CO(2)) and methane (CH(4)) emissions made up 51-95% and 0.3-3.9% respectively of the lost C. The total loss of nitrogen (N) during composting was 51-68% and the nitrous oxide (N(2)O) made up 2.8-6.3% of this loss. The NH(3) losses were very uncertain but small. The amount of leachate was 130 L Mg(-1) wet waste (ww) and the composition was similar to other leachate compositions from home composting (and centralised composting) reported in literature. The loss of heavy metals via leachate was negligible and the loss of C and N via leachate was very low (0.3-0.6% of the total loss of C and 1.3-3.0% of the total emitted N). Also the compost composition was within the typical ranges reported previously for home composting. The level of heavy metals in the compost produced was below all threshold values and the compost was thus suitable for use in private gardens.     

Occurrence of enteric pathogens in composted domestic solid waste containing disposable diapers

Information has not been previously available on the occurrence of enteric pathogenic viruses and protozoan parasites in composted municipal domestic solid waste. A potential source of these pathogens in domestic solid waste is disposal diapers. The occurrence of enteroviruses, Giardia cysts, Cryptosporidium oocysts and Salmonella were determined in municipal composted domestic solid waste, and solid waste to which extra diapers had been added to increase their concentration 2–4 fold (6.6–7.7% by weight) above that found normally in municipal solid waste before composting. The compost was tested at various periods of time during aging (101–203 days). No enteroviruses or protozoan cysts or oocysts were detected in any of the samples collected during this period. One sample out of 19 collected (after 175 days aging) was positive for Salmonella. These results suggest that enteric pathogens were destroyed during the composting process, or were present in numbers below the detection method (i.e. one organism per 40–50g of compost) used in this study.     

Questionnaire and onsite survey on municipal solid waste composting in Sri Lanka

This study was conducted to evaluate the composting processes in Sri Lanka and to identify essential improvements. The study consisted of a questionnaire survey, field observations, and interviews. The main shortcomings identified by this study were: no source separation at origin, and no monitoring for temperature, moisture, stability, or maturity during processes of composting. These problems hinder the smooth operation of the composting processes and lead to low demand for compost. Based on the findings, the recommendations for increasing the demand for compost are performing source separation during waste collections, improvement of processes by monitoring the temperature and moisture, and marketing compost so as to improve the popularity of the compost among farmers.     

Odour control at biowaste composting facilities

There are several options to effectively reduce odorous emissions at composting facilities depending on the type of composting system used. Some of the more relevant measures for open and enclosed composting facilities are presented in this article. Results from different investigations on odour reduction efficiencies of biological waste gas treatment systems at various scales are presented. Biofilter/bioscrubber combinations were used and different biofilter materials were tested. The more relevant odorous substances in the waste gas were identified, and their reduction in the different systems was measured. The biofilter proved to be mainly responsible for efficient odour degradation. The investigations presented in this article revealed that screened compost was very effective, and proved to be a low cost biofilter material for odour degradation purposes. Screened compost showed higher degradation rates than a coke-compost mixture newly developed by the University of Leipzig. Furthermore, it seems that enclosed systems have advantages when compared to conventional open single bed biofilters.     

Air permeability of compost as related to bulk density and volumetric air content.

Compost air permeability controls air flow through compost during composting or when using compost as biofilter material. Air permeability is therefore an important characteristic of compost. The relationships between air permeability (k(a)) in compost and compost dry bulk density (rho b), gravimetric water content (omega), and volumetric air content (epsilon) was investigated for two types of composts. The composts used were produced from a digested sewage sludge-straw mixture and from garden waste and measurements were conducted on sieved and repacked 100 cm3 compost samples. Results showed a linear relation between log(k(a)) and rho b at constant values of omega for both composts, indicating an exponential relationship between k(a) and rho b. The slopes of these relationships generally became more negative with increasing rho b. The results further showed a linear relationship between log(k(a)) and log(epsilon) for both composts as also often observed for soils. It was observed that the log(k(a)) and log(epsilon) relationships for the garden waste compost all intercepted at the same location despite having very different slopes. This means that it is possible to predict the entire k(a)-epsilon relationship using only one measurement of corresponding (k(a), epsilon) for garden waste. It was not possible to determine whether this was also the case for the sewage sludge compost due to difficulties in sample preparation at low and high water content.     

Indicator organisms for assessing sanitization during composting of plant wastes

The potential for using plant pathogens and seeds as indicator organisms for assessing sanitization of plant wastes during composting was tested in bench-scale flask and large-scale systems. Plasmodiophora brassicae was unsuitable due to high temperature tolerance in dry to moist composts, and detection of viable inoculum post-composting using bioassay plants not corresponding with that using TaqMan® PCR, possibly due to preservation of nucleic acids at elevated temperatures. Several other plant pathogens (Sclerotinia sclerotiorum, Microdochium nivale, Phytophthora cinnamomi and Phytophthora nicotianae) were unsuitable due their low temperature tolerance. Fusarium oxysporum f.sp. cepae and f.sp. radicis-lycopersici chlamydospores and tomato seeds were suitable indicators due to their moderate temperature tolerance and ease of viability testing post-composting. Abutilon seeds were more tolerant than tomato seeds of compost temperatures ?52 °C but more prone to degradation at lower temperatures and therefore less suitable as indicators. Relationships between compost temperature during exposures of 2-10 days and subsequent viability of the above chlamydospores or seeds enabled the sanitizing effect of composting processes to be predicted within 2-6 days. Plant waste type (woody or vegetable) had a small but significant effect on the relationship for tomato seeds but not for F. oxysporum chlamydospores.     

Composting clam processing wastes in a laboratory- and pilot-scale in-vessel system

Waste materials from the clam processing industry (offal, shells) have several special characteristics such as a high salinity level, a high nitrogen content, and a low C/N ratio. The traditional disposal of clam waste through landfilling is facing the challenges of limited land available, increasing tipping fees, and strict environmental and regulatory scrutiny. The aim of this work is to investigate the performance of in-vessel composting as an alternative for landfill application of these materials. Experiments were performed in both laboratory-scale (5L) and pilot-scale (120L) reactors, with woodchips as the bulking agent. In the laboratory-scale composting test, the clam waste and woodchips were mixed in ratios from 1:0.5 to 1:3 (w/w, wet weight). The high ratios resulted in a better temperature performance, a higher electrical conductivity, and a higher ash content than the low-ratio composting. The C/N ratio of the composts was in the range of 9:1-18:1. In the pilot-scale composting test, a 1:1 ratio of clam waste to woodchips was used. The temperature profile during the composting process met the US Environmental Protection Agency sanitary requirement. The final cured compost had a C/N ratio of 14.6, with an ash content of 167.0+/-14.1g/kg dry matter. In addition to the major nutrients (carbon, nitrogen, calcium, magnesium, phosphorus, potassium, sulfur, and sodium), the compost also contained trace amounts of zinc, manganese, copper, and boron, indicating that the material can be used as a good resource for plant nutrients.     

Microbiological assessments of compost toilets: in situ measurements and laboratory studies on the survival of fecal microbial indicators using sentinel chambers

Compost toilet systems were assessed for their ability to reduce microbial indicators and pathogens. Bacterial pathogens were not detected in any samples indicating a low survival rate in composting feces and/or an initial low occurrence. Indicator bacteria showed large variations with no clear trend of lower bacterial numbers after longer storage. In controlled composting experiments, thermophilic conditions were only reached when amendments were made (grass and a sugar solution). Even then it was impossible to ensure a homogenous temperature in the composting fecal material and therefore difficult to achieve a uniform reduction and killing of indicator organisms. Presumptive thermotolerant coliforms, Salmonella typhimurium Phage 28 B and eggs of Ascaridia galli, proved useful as indicators. However, regrowth was detected for enterococci and total numbers of bacteria grown at 36 degrees C. These indicator parameters may therefore overestimate the level of other (pathogenic) bacteria present in the material and can not be recommended for use as reliable indicator organisms in composting toilet systems. The addition of indicator bacteria to fecal material contained in semi-permeable capsules proved to be a useful technique to ensure that microorganisms were contained in a small test volume.