Dechlorination of carbon tetrachloride by the catalyzed Fe-Cu process

The electrochemical reduction characteristics of carbon tetrachloride (CT) were investigated using cyclic voltammetry in this study. In addition, the difference in reduction mechanisms of CT between Master Builders' iron and the catalyzed Fe-Cu process was discussed. The results showed that CT was reduced directly on the surface of copper rather than by atomic hydrogen produced at the cathode in the catalyzed Fe-Cu process. The reduction was realized largely by atomic hydrogen in Master Builders' iron. The entire CT in 350 ml aqueous solution with 320 mgL was reduced to trichloromethane and dichloromethane in 2.25 h when 100 g of scrap iron with FeCu ratio of 10:1 (ww) were used. Moreover, the reduction rate slowed with time. CT could be reduced at acidic, neutral and alkaline pH from solution by Fe-Cu bimetallic media, but the mechanisms were di?erent. The degradation rate was not significantly in?uenced by pH in the catalyzed Fe-Cu process; in Master Builders' iron it clearly increased with decreasing pH. The kinetics of the reductions followed pseudo-first order in both cases. Furthermore, the reductions under acidic conditions proceeded faster than that under the neutral and alkaline conditions. The catalyzed Fe-Cu process was superior to Master Builders' iron in treating CT-containing water and this advantage was particularly noticeable under alkaline conditions. The reduction was investigated in the cathode (Cu) and anode (Fe) compartments respectively, the results showed that the direct reduction pathway played an important role in the reduction by the catalyzed Fe-Cu process. The catalyzed Fe-Cu process is of practical value.     

Performance of bioferric-submerged membrane bioreactor for dyeing wastewater treatment

Adding iron salt or iron hydroxide to sludgemixed liquor in an aeration tank of a conventional activated sludge processes (bioferric process) can simultaneously improve the sludge’s filterability and enhance the system’s treatment capacity. In view of this, Fe(OH)₃ was added to a submerged membrane bioreactor (SMBR) to enhance the removal efficiency and to mitigate membrane fouling. Bioferric process and SMBR were combined to create a novel process called Bioferric-SMBR. A side-by-side comparison study of Bioferric-SMBR and common SMBR dealing with dyeing wastewater was carried out. Bioferric-SMBR showed potential superiority, which could enhance removal efficiency, reduce membrane fouling and improve sludge characteristic. When volumetric loading rate was 25% higher than that of common SMBR, the removal efficiencies of Bioferric-SMBR on COD, dye, and NH₄ ⁺-N were 1.0%, 9.5%, and 5.2% higher than that of common SMBR, respectively. The trans-membrane pressure of Bioferric-SMBR was only 36% of that in common SMBR while its membrane flux was 25% higher than that of common SMBR. The stable running period in Bioferric-SMBR was 2.5 times of that in common SMBR when there was no surplus sludge discharged. The mixed liquor suspended solids concentration of Bioferric-SMBR was higher than that of common SMBR with more diversified kinds of microorganisms such as protozoans and metazoans. The mean particle diameter and specific oxygen uptake rate of Bioferric-SMBR were 3.10 and 1.23 times the common SMBR, respectively. Translated from Environmental Science, 2005, 26(6): 65–70 [译自: 环境科学]     

Low intensity ultrasound stimulates biological activity of aerobic activated sludge

This work aims to explore a procedure to improve biological wastewater treatment efficiency using low intensity ultrasound. The aerobic activated sludge from a municipal wastewater treatment plant was used as the experimental material. Oxygen uptake rate (OUR) of the activated sludge (AS) was determined to indicate the changes of AS activity stimulated by ultrasound at 35 kHz for 0–40 min with ultrasonic intensities of 0–1.2 W/cm². The highest OUR was observed at the ultrasonic intensity of 0.3 W/cm² and an irradiation period of 10 min; more than 15% increase was achieved immediately after sonication. More significantly, the AS activity stimulated by ultrasound could last 24 h after sonication, and the AS activity achieved its peak value within 8 h after sonication, or nearly 100% higher than the initial level after sonication. Therefore, to improve the wastewater treatment efficiency of bioreactors, ultrasound with an intensity of 0.3 W/cm² could be employed to irradiate a part of the AS in the bioreactor for 10 min every 8 h. Translated from Environmental Science, 2005, 26(4): 124–128 [译自: 环境科学]     

赤泥活化过一硫酸盐降解环丙沙星:性能和机制

为提高赤泥的综合利用及抗生素有机废水的深度处理,以赤泥（red mud,RM）为催化剂、环丙沙星（ciprofloxacin,CIP）为目标污染物,系统研究了RM活化过一硫酸盐（peroxymonosulfate,PMS）降解CIP的效果和机制.结果表明,含有Fe、Al和Ca等金属氧化物,具有较大比表面积（10.96 m²·g^-1）和复杂孔道结构的RM能够有效增强PMS对CIP的降解速率和效果.自由基捕获剂甲醇、叔丁醇和苯酚的抑制实验结果进一步说明,体系产生的SO₄^-·和HO·在RM表面与CIP发生氧化反应.温度、PMS浓度和RM投加量影响CIP的降解.温度升高反应速度加快,反应活化能为5.74 kJ·mol^-1; PMS浓度增加,体系产生更多SO₄^-·和HO·,CIP的降解率升高; RM存在最佳投加量1.0 g·L^-1.HPLC/MS/MS共检测到8种降解产物,CIP分子中的哌嗪环易受活性物质进攻,CIP主要通过2种途径进行降解.本研究表明RM是一种极具潜力的廉价催化剂,可用于活化过一硫酸盐处理含抗生素的污染废水.     

制药废水二级出水中溶解性有机物混凝去除特性研究

制药废水二级出水中溶解性有机物(DOM)由于组成复杂、难去除、具有多异质性和分散性,是污水深度处理与回用的主要去除对象和关键限制因子.本论文以发酵制药废水二级出水的DOM为研究对象,采用投加聚合氯化铝(PAC)混凝剂去除DOM,考察混凝剂投加量和混凝pH值对去除效果的影响,并结合分子量分级、亲疏水性分级以及三维荧光光谱-平行因子分析方法等对DOM进行了系统表征和分析,进一步阐述混凝过程DOM的去除特征.结果表明,PAC投加量为250 mg·L~(-1)、pH=7时,混凝沉淀30 min对DOC、UV_(254)、色度和浊度的去除率分别为13.05%±0.29%、23.65%±0.75%、12.66%±1.34%、63.67%±0.89%;混凝对分子量10 kDa的组分和疏水中性(HON)组分去除效果分别为50.33%±0.98%、21.56%±0.42%,而对分子量1 kDa组分去除率较低为2.26%±0.12%;三维荧光光谱-平行因子分析将制药废水二级出水分为2个类腐殖质组分(C1、C3)和1个类蛋白组分(C2),混凝对类腐殖酸组分(C1)最大荧光强度去除率(F_(max))最高为46.22%,而亲水性的小分子和蛋白类物质混凝去除效果较差.     

微生物电解系统生物阴极的硫酸盐还原特性研究

针对传统硫酸盐生物还原方法中供氢体系能耗大和氢气利用率低的特点,构建双极室微生物电解系统(microbial electrolysis system,MES),研究了微生物利用阴极作为电子供体去除废水中硫酸盐及电子利用的特性.外加电压为0.8 V时,MES生物阴极在36 h内SO2-4平均去除量为109.8 mg·L-1,平均还原速率可达73.2 mg·(L·d)-1.运行时MES的最高电流密度为50~60 A·m-3,电子回收率为(43.3±10.7)%,约90%的电子被用于还原SO2-4.微生物利用MES阴极产生的H2作为电子供体还原SO2-4,主要还原产物为溶解态的S2-和气态的H2S,还原过程主要发生在前12 h.对MES施加不同外加电压的实验显示,外加电压为0.8 V时的SO2-4去除率和电荷量都比0.4 V时高;但0.4 V情形下MES的电子回收率可达到70%,且周期结束时阴极H2低于检出限,推测微生物可以直接利用阴极的电子从而提高了能量效率.实验结果最终表明,微生物可利用MES的阴极进行代谢去除废水中的SO2-4,阳极微生物产生电子降低了系统能耗,这为含硫酸盐废水的高效低耗处理提供了新的研究思路.     

Process evaluation of an alternating aerobic-anoxic process applied in a sequencing batch reactor for nitrogen removal

In order to improve the nitrogen removal efficiency and save operational cost, the feasibility of the alternating aerobic-anoxic process (AAA process) applied in a sequencing batch reactor (SBR) system for nitrogen removal was investigated. Under sufficient influent alkalinity, the AAA process did not have an advantage over one aerobicanoxic (OAA) cycle on treatment efficiency because microorganisms had an adaptive stage at the alternating aerobic-anoxic transition, which would prolong the total cycling time. On the contrary, the AAA process made the system control more complicated. Under deficient influent alkalinity, when compared to OAA, the AAA process improved treatment efficiency and effluent quality with NH₄ ⁺-N in the effluent below the detection limit. In the nitrification, the average stoichiometric ratio between alkalinity consumption and ammonia oxidation is calculated to be 7.07 mg CaCO₃/mg NH₄ ⁺-N. In the denitrification, the average stoichiometric ratio between alkalinity production and NO₃ ⁻-N reduction is about 3.57 mg CaCO₃/mg NO₃ ⁻-N. As a result, half of the alkalinity previously consumed during the aerobic nitrification was recovered during the subsequent anoxic denitrification period. That was why the higher treatment efficiency in the AAA process was achieved without the supplement of bicarbonate alkalinity. If the lack of alkalinity in the influent was less than 1/3 of that needed, there is no need for external alkalinity addition and treatment efficiency was the same as that under sufficient influent alkalinity. Even if the lack of alkalinity in the influent was more than 1/3 of that needed, the AAA process was an optimal strategy because it reduced the external alkalinity addition and saved on operational cost. Translated from Acta Scientiae Circumstantiae, 2004, 24(4): 576–580 [译自: 环境科学学报]     

pH冲击对海洋厌氧氨氧化菌处理含海水污水脱氮效能的影响

采用ASBR反应器,研究了pH冲击对海洋厌氧氨氧化菌处理含海水污水脱氮效能的影响,并利用Andrew模型和Ratkowsky模型模拟pH冲击下海洋厌氧氨氧化菌的脱氮过程.结果表明,当pH在7~8时,反应器的脱氮效果最佳,氨氮去除负荷(NRR)稳定在(0.30±0.04)kg·(m~3·d)~(-1),总氮去除率(TNRE)在(76.73±5.74)%;当pH为8.5时,游离氨(FA)的平均浓度为14.22 mg·L~(-1),该FA浓度对NRR的影响较小,NRR仍维持在(0.30±0.02)kg·(m~3·d)~(-1)左右,但是NO_2~--N在pH的直接影响下出现了积累,不能够完全去除,此条件不利于反应器的稳定运行;当pH为6.5和9时,FA浓度分别为0.22mg·L~(-1)和37.84 mg·L~(-1),NRR分别低至(0.10±0.02)kg·(m~3·d)~(-1)和(0.15±0.02)kg·(m~3·d)~(-1),且TNRE仅为(23.04±9.88)%和(42.12±5.52)%.海洋厌氧氨氧化菌在碱性条件下的耐受性强于酸性条件.采用修正的Andrew模型进行拟合,得到了NRR与FA之间的相互关系,同时还可以得到NRR_(max)、k_S和k_I等参数,对于表征海洋厌氧氨氧化菌的脱氮过程具有实际意义.     

采用含硫铁化学污泥作为反硝化电子供体进行焦化废水中总氮深度去除

城市污水处理和大部分的工业废水处理工艺的出水总氮普遍难以达标排放,基于进水水质的C/N值不稳定、提高回流比造成水力负荷增大、降低反应动力学并且耗能、投加有机碳源带来二次污染以及高污泥产率等问题,急需寻求一种节能降耗、操作简单的深度脱氮方法.对此,利用含硫工业废水预处理产生的含硫铁化学污泥作为固相电子供体进行自养反硝化深度脱氮,实验过程中,以焦化废水二级生物出水作为研究对象,考察脱氮性能、硫铁泥转变过程及微生物群落变化,求出废水深度脱氮新工艺的优化反应条件与效果范围.当进水NO_3~--N、NO_2~--N浓度分别是(74.54±0.57)mg·L~(-1)、(1.11±0.19)mg·L~(-1),水力停留时间为18 h时,对应出水浓度分别降低至(2.78±1.08)mg·L~(-1)、(2.87±0.71)mg·L~(-1);TON(NO_3~--N+NO_2~--N)去除率高达90.0%;NO_3~--N还原速率和NO_2~--N累积速率分别为12.06 mmol·(L·d)-1、7.74 mmol·(L·d)-1.结果表明,以副产物化学硫铁泥作为电子供体深度脱氮有潜在的工程应用价值,以水处理工艺过程中原位利用废物,解决部分富硫铁化学污泥后续处理问题,表现出资源化利用的综合特征.     

Electrochemical reduction characteristics and mechanism of nitrobenzene compounds in the catalyzed Fe-Cu process

The reduction of the nitrobenzene compounds （NBCs） by the catalyzed Fe-Cu process and the relationship between the electrochemical reduction characteristics of NBCs at copper electrode and reduction rate were studied in alkaline medium（pH=11）. The catalyzed Fe-Cu process was found more effective on degradation of NBCs compared to Master Builder＇s iron. The reduction rate by the catalyzed Fe-Cu process decreased in the following order： nitrobenzene 〉4-chloro-nitrobenzene ≥m-dinitrobenzene ：〉 4-nitrophenol ≥2,4-dinitrotoluene 〉2-nitrophenol. The reduction rate by Master Builder＇s iron decreased in the following order： m-dinitrobenzene ≥4-chloro-nitrobenzene 〉4-nitrophenol 〉2,4-dinitrotoluene ≈nitrobenzene 〉2-nitrophenol. NBCs were reduced directly on the surface of copper rather than by the hydrogen produced at cathode in the catalyzed Fe-Cu process. The reduction was realized by the hydrogen produced at cathode and Fe（OH）2 in Master Builder＇s iron, It is an essential difference in reaction mechanisms between these two technologies. For this reason, the reduction by the catalyzed Fe-Cu depended greatly on NBC＇s electron withdrawing ability.     

污水磷回收新产物——蓝铁矿

渐行渐近的磷危机使磷回收从理论已经走向实践.磷回收产物形式很多,但经济、具有高附加值的产物才能驱动企业自愿实施.在污水处理生物污泥中新近发现的蓝铁矿(Vivianite,Fe_3(PO_4)_2·8H_2O)沉淀物因潜在的特殊用途以及经济价值而备受关注.自然界,蓝铁矿广泛存在于地表水体沉积物中,是一种非常稳定(K_(sp)=10~(-36))的磷铁化合物.决定蓝铁矿生成的条件除富铁、富磷之内在因素外,还需要环境中存在合适的还原性条件(ORP-300 mV)以及中性上下的pH条件(6～9).实践中,污水或污水处理过程中有时刚好存在蓝铁矿形成的内、外在条件,荷兰污水处理厂在生物污泥中便检测发现有蓝铁矿物质的存在.为推动蓝铁矿基础及其应用研究,本文综述蓝铁矿化学性质、经济价值及回收潜力;分析pH、ORP、微生物、硫化物等环境影响因素;辨析其在生物污泥中的生成路径;提出从污泥中分离、提纯蓝铁矿的研发思路.     

DPR-SNED系统处理低C/N城市污水与硝酸盐废水的运行特性

为实现低C/N城市污水与含硝酸盐废水的同步处理,采用SBR接种活性污泥,通过合理控制厌氧/缺氧/低氧时间和溶解氧(DO)浓度,实现了反硝化除磷耦合同步硝化内源反硝化(DPR-SNED)系统的启动,并对启动过程中系统的脱氮除磷特性进行了研究.结果表明采用厌氧/低氧的运行方式,控制厌氧时间为3 h,好氧段DO浓度为0. 5～1. 0 mg·L-1,60 d可实现同步硝化内源反硝化除磷(SNEDPR)系统的启动,出水PO_4~(3-)-P浓度0. 5 mg·L-1,系统氮磷去除率维持在90%以上,COD的去除率维持在80%以上,系统SNED率和CODins率分别维持在70%和95%左右;随后改变运行方式,采用厌氧/缺氧/低氧的方式运行,缺氧段前进含硝酸盐废水,45 d可实现DPR-SNED系统的启动,缺氧末PO_4~(3-)-P浓度1. 1 mg·L-1,出水PO_4~(3-)-P浓度0. 5 mg·L-1,系统磷、COD去除率均维持在90%以上,氮去除率维持在88%以上,系统SNED率和CODins率分别维持在62%和90%左右. DPR-SNED系统的成功启动后,厌氧段聚糖菌和聚磷菌对城市污水有限碳源的充分利用和强化储存,可为后续缺氧段及好氧段的脱氮除磷提供充足的内碳源.此外,DPR-SNED系统缺氧段内源短程反硝化的进行保障了系统在低C/N(4)条件下的高效脱氮.     

碱度对沸石序批式反应器亚硝化的影响

本研究采用沸石序批式反应器(ZSBR)在常温(25℃±1℃)下实现快速稳定的亚硝化,亚硝酸盐氮积累率维持在90.0%以上,并且考察了在进水氨氮500 mg·L~(-1)时,4个不同碱度(以CaCO_3计)对ZSBR亚硝化的影响.结果表明,ZSBR实现快速亚硝化的关键是游离氨(FA)对亚硝酸盐氧化菌(NOB)的抑制作用远大于其对氨氧化菌(AOB)的抑制作用,并且经此过程转化后的含氨氮的废水,可以作为厌氧氨氧化的进水,进一步脱除水中的氨氮与总氮,当系统投加碱度(以CaCO_3计)为2 500mg·L~(-1)时,ZSBR亚硝化效果最好,平均氨氮转化率为66.7%,平均亚硝酸盐氮积累率为98.1%,平均亚硝酸盐氮产率为0.74 kg·(m~3·d)~(-1).高通量测序分析表明ZSBR长时间运行后微生物群落发生显著变化,AOB得到富集,NOB在FA的抑制作用下不断被淘洗出反应器.     

铁刨花-Fenton-絮凝工艺对染料生产废水中AOX、色度和TOC的去除效果研究

采用铁刨花-Fenton-絮凝工艺处理染料生产废水,考察了不同Fe~(2+)与H_2O_2摩尔比(1∶3~1∶15)、铁刨花反应时间(2~5h)、Fenton氧化反应时间(20~80 min)下可吸附性有机卤代物(AOX)、色度和总有机碳(TOC)的去除效果.结果表明,AOX、色度和TOC去除率随Fe~(2+)与H_2O_2摩尔比的降低先升高后减少,随铁刨花和Fenton反应时间的增加而持续升高.最优化条件为Fe~(2+)与H_2O_2摩尔比1∶8、铁刨花反应时间4 h和Fenton反应时间60 min,该条件下AOX、色度和TOC的去除率分别为94.2%、93.7%和27.2%.比较实验结果表明,铁刨花-Fenton-絮凝组合工艺对废水AOX、色度和TOC的去除效果远优于铁刨花处理、Fenton氧化、絮凝沉淀的单个技术或两两技术组合效果.GC-MS分析表明,废水中的有机卤代物和苯胺类污染物得到高效去除,此外硝基苯类、苯酚类、苯甲醛类、醚类、腈类和杂环化合物等有毒有害物质也均得到高效去除.叔丁醇捕获·OH实验表明·OH在Fenton反应中的主导作用.     

新生态型聚硅酸铁锰处理染料废水的优化

为了提高混凝剂对染料废水的净化效率,本文利用硅酸钠、硫酸亚铁和高锰酸钾为原料合成了新型复配混凝剂聚硅酸铁锰(PSFM),分别以直接大红、分散蓝和活性黄染料废水为处理对象进行混凝模拟实验,研究了碱度和浊度等因素对PSFM混凝去除染料性能影响.结果表明,PSFM对直接大红和分散蓝染料废水具有较好的混凝净化效能,其色度和TOC去除率分别可达99.2%、95.4%和98.5%、93.8%,效果优于聚硅酸铁(PSF)、Al2(SO4)3和Fe Cl3等常规混凝剂,PSFM对活性黄染料废水色度和TOC去除率分别为56.3%和51.3%.浊度对PSFM混凝效能无明显影响.在碱度分别为50、0和75 mg·L~(-1)时,PSFM对直接大红、分散蓝和活性黄去除率分别达到最高.此外,利用扫描电子显微镜(SEM)、傅里叶红外(FTIR)和X射线衍射仪(XRD)等高级表征手段对PSFM进行了表征,对混凝过程中的混合液和絮体分别进行Zeta电位和絮体粒径在线监测,探索得PSFM混凝主要机制为Fe+与Mn+水解产生的带正电的多核配合物和聚硅的桥联聚合,同时还包括新生态水合二氧化锰和羟基氧化铁的吸附助凝作用.     

磁混凝对市政污水中抗生素抗性基因和重金属抗性基因的削减效能

污水中抗性基因给环境和人类健康带来潜在的危害.本研究通过调查市政排口污水磁混凝处理过程中抗性基因绝对含量和相对丰度变化,考察磁分离技术对市政污水中抗性基因的削减效果.结果表明,加入磁种和絮凝剂的一级搅拌和二级搅拌对抗生素抗性基因(ARGs)、重金属抗性基因(MRGs)和可移动遗传元件均有较好地去除效果,但出水中部分抗性基因的绝对含量增加,这可能是由于出水中依然具有较高含量的水平转移元件(int1,2. 00×10~(10) copies·mL~(-1); int2,1. 91×10~8 copies·mL~(-1); Tn916/1545e,5. 38×10~8 copies·mL~(-1)).网络分析和主成分分析结果表明,磁混凝处理过程中ARGs与MRGs呈显著正相关(P 0. 05),城市污水中常规污染物如悬浮物、磷和COD等是影响抗性基因去除效率的重要因子.这些结果表明,磁混凝可通过有效削减污水中常规污染物进而制约抗性基因的传播和转移;但需要关注磁混凝的出水及脱水污泥的后续管理,如出水前增设消毒环节,以降低抗性基因污染风险.     

Effect of the addition of organic carbon sources on nitrous oxide emission in anaerobic-aerobic (low dissolved oxygen) sequencing batch reactors

The effect of additional organic carbon sources on the production of nitrous oxide (N₂O) in anaerobic-aerobic (low dissolved oxygen) real wastewater treatment system was investigated. In this paper, three laboratory-scale sequencing batch reactors (SBRs) (SBR-1, SBR-2 and SBR-3) were operating under an anaerobic-aerobic (low dissolved oxygen, 0.15–0.45 mg·L⁻¹) configuration. The SBRs were ‘long-term cultured’ respectively with a single municipal wastewater sample, sodium acetate, and a waste-activated sludge alkaline fermentation liquid as the additional carbon sources of real wastewater. Off-gas analysis showed that N₂O was emitted into the atmosphere during the aerobic (low dissolved oxygen) period in the three SBRs, and the order of N₂O emission rate was SBR-2>SBR-1>SBR-3. It was observed that the higher poly-β-hydroxyvalerate fraction of polyhydroxyalkanoates, the lower glycogen transformation and less nitrite accumulation was in SBR-3, while the opposite behavior was observed in SBR-2. Further research indicated that the interaction of the factors above potentially affected the N₂O emission in the anaerobic-aerobic (low dissolved oxygen) system.     

实际污水培养好氧颗粒污泥及其特性研究

采用实际城市污水在序批式反应器(SBR)中试装置中成功培养出好氧颗粒污泥.颗粒污泥的沉降速率>21 m·h-1,显示了良好的沉降性能.颗粒污泥对化学需氧量(COD)、氮(N)、磷(P)具有同步去除的能力.在3 h的运行周期中,反应器出水COD<50 mg·L-1,氨氮(NH+4-N)<5.0 mg·L-1,总氮(TN)<15 mg·L-1,对TN和总磷(TP)的去除率达到50%.采用共聚焦激光扫描显微镜(CLSM)对好氧颗粒污泥的结构分析表明,好氧颗粒污泥的胞外多聚物(EPS)在整个颗粒污泥中均匀地分布,构成颗粒污泥的骨架.对颗粒污泥的X射线衍射(XRD)分析显示,在好氧颗粒污泥的内部存在许多无机矿物质,在颗粒污泥形成初期,废水中的无机成分可能具有"晶核"的作用.     

Bi-PbO2电极电化学氧化去除模拟废水中氨氮的研究

本实验采用钛网作为基体,利用电沉积方法制备了纯PbO2电极和Bi-PbO2电极,通过SEM、XRD、XPS对电极的表面形态进行了表征,利用循环伏安法对Bi-PbO2电极电化学特性进行了研究.同时,以氨氮模拟废水作为研究对象,考察了Bi-PbO2电极的电催化活性,探讨了氨氮电化学氧化降解机理.结果表明,Bi-PbO2电极的形态表征、电催化活性明显高于纯PbO2电极,氨氮的去除效率随电流密度的增加而提高,碱性条件下氨氮的去除效果明显好于酸性条件,适量浓度的Cl-的引入在碱性条件下提高了氨氮的去除效果.当氨氮初始浓度为50 mg·L-1、电流密度为40 mA·cm-2、pH=12、Cl-浓度为600 mg·L-1时,电解120 min后,氨氮100%去除.氨氮的降解机理为:体系中无添加氯离子,酸性条件下氨氮主要是通过间接氧化去除,碱性条件下通过直接电氧化和间接氧化共同完成;体系中添加氯离子,氨氮的去除主要是通过溶液中生成的有效氯间接氧化去除.     

生物膜贴壁培养小球藻净化猪粪沼液废水的效果

微藻处理猪粪沼液废水是一项污水资源化生物技术.本文以小球藻为研究对象,通过贴壁培养方式,对稀释不同倍数的猪粪沼液废水进行净化处理同时提取藻细胞油脂,旨在探究小球藻贴壁培养处理猪粪沼液废水的效果,分析小球藻耐受猪粪沼液废水的氨氮浓度.将猪粪沼液废水分别稀释1倍(原水)、2倍、5倍、10倍制成培养基.测定贴壁培养小球藻对各处理组猪粪沼液废水中COD、氨氮、总氮、总磷的去除效率及对重金属铜、锌、铁的富集效果,同时探究小球藻的油脂合成情况.结果表明,当猪粪沼液废水稀释5倍时,贴壁小球藻对COD、氨氮、总氮、总磷的净化效果最佳,其去除效率分别为:86.8%、94.1%、85.2%、84.3%;油脂含量高达32.7%;对重金属铜、锌、铁的去除效率分别为:72.9%、70.0%、73.0%;培养一个周期结束时生物产率达到4.21 g·(m~2·d)~(-1).该研究将微藻与难处理的猪粪沼液废水深度净化进行了有效的结合,为实现藻类生物燃料工艺生产及降低废水处理成本提供理论基础.