UV／TiO2薄膜体系光降解酞酸酯研究

采用自制玻璃负载TiO2薄膜，研究了UV-Vis／TiO2以及UV／TiO2／H2O2体系对2种酞酸酯DBP和DEHP的光催化降解情况。研究结果表明，TiO2在暗处对酞酸酯没有降解作用；UV／TiO2体系能有效光降解DBP和DEHP，TiO2具有明显的光催化作用，增强因子分别为，fDBP=2．06，fDEHP=1．53；在一定浓度范围内DBP在UV／TiO2体系中的降解速率与其初始浓度成负一级动力学关系；UV／TiO2／H2O2体系对DBP的光降解能力远大于UV／TiO2和UV／H2O2体系，H2O2能显著提高TiO2的光催化活性。     

光催化-臭氧氧化降解H酸的研究

采用光催化一臭氧氧化技术（催化膜／UV／O3）降解H酸。研究结果表明，光催化与臭氧氧化相结合具有明显的协同作用。实验进一步讨论了臭氧投加量、废水初始pH值和H酸初始浓度对光催化一臭氧氧化降解H酸的影响。降解后的H酸，萘环结构被破坏，可生化性提高。     

高级氧化法脱除PVA浆料的清洁生产新工艺研究

为了研究高级氧化法脱除聚乙烯醇（PVA）浆料清洁生产新工艺的可行性，研究了3种高级氧化法UV／H2O2、UV／TiO2、Nation-Fe^2＋／H2O2对含PVA溶液的氧化降解，其降解效果依次为iUV／H2O2〉Nation-Fe^2＋／H2O2〉UV／TiO2。对于UV／H2O2法，PVA降解速率与H2O2的初始浓度成正相关，且H2O2浓度为2．95mmol／L时14min内就能使PVA的去除率达到98％；pH和温度对PVA的氧化降解效果影响不明显。在此基础上，对建立在高级氧化法基础上的退浆新工艺进行了探讨，结果表明，在65℃和75℃下，高级氧化法条件下的纯棉织物PVA退浆率分别达到70．16％和95．65％；该法不仅可以促进PVA从纯棉织物上的脱附，而且可以达到对PVA的较高降解效果，使得所排退浆废水的生化处理难度明显降低。     

TiO2/H2O2/UV和TiO2/O3/UV降解对氯苯甲酸和喹啉的试验研究

主要叙述TiO2/H2O2/UV和TiO2/O3/UV体系降解对氯苯甲酸(4-CBA)和喹啉的试验研究.研究表明,(1)在TiO2/H2O2/UV体系里目标物降解速度先随过氧化氢投加量的增加而提高,但超过一定浓度之后便开始下降;(2)在TiO2/O3/UV体系中,目标降解物的反应速度都非常快,且臭氧浓度高的时候降解速度更快;(3)二氧化钛催化剂在TiO2/O3/UV体系中作为积极因素有助于提高反应速率,而在TiO2/H2O2/UV体系是消极因素,会降低反应速率.     

TiO2/H2O2/UV和TiO2/O3/UV降解对氯苯甲酸和喹啉的试验研究

主要叙述TiO2/H2O2/UV和TiO2/O3/UV体系降解对氯苯甲酸（4-CBA）和喹啉的试验研究.研究表明,（1）在TiO2/H2O2/UV体系里目标物降解速度先随过氧化氢投加量的增加而提高,但超过一定浓度之后便开始下降;（2）在TiO2/O3/UV体系中,目标降解物的反应速度都非常快,且臭氧浓度高的时候降解速度更快;（3）二氧化钛催化剂在TiO2/O3/UV体系中作为积极因素有助于提高反应速率,而在TiO2/H2O2/UV体系是消极因素,会降低反应速率.     

光催化臭氧氧化法在废水处理中的研究进展

光催化臭氧氧化法作为一种有效的废水处理技术,对难降解的有机废水,具有良好的降解功效。文中分析了UV/O3/Fe2＋、UV/O3/Fe3＋和UV/O3/H2O2体系的反应机理,介绍了光催化臭氧氧化法在废水处理中的应用情况,指出了光催化臭氧氧化法存在的问题和展望。     

紫外光助O3、H2O2氧化降解炼油废碱水的可行性实验

炼油高浓度有机废碱水是石化行业中很难降解的废水。本实验用光化学氧化技术对其进行了降解研究，比较了紫外光／空气、紫外光／O3、紫外光／空气／H2O2系统的处理效果。结果表明，光化学氧化技术降解此废水是可行的，紫外光可使废水中COD、油、酚的降解率明显提高。当废水中O3的投加量每小时为22mg／L，或H2O2投加量为1％／L时，UV／O3法与UV／空气／H2O2法的降解效果相近。同时，通过控制O，浓度或H2O2的投加量等条件，可使废水中COD、油、酚和硫化物降解到地方污染物二级排放标准。     

O3／UV预处理磺酰脲类除草剂生产废水的研究

采用O3／UV工艺预处理磺酰脲类除草剂生产废水，考察了初始pH值、臭氧投量、叔丁醇投加等因素对废水处理效果的影响，并初步探讨了该工艺处理废水的反应机理。实验结果表明，在废水初始pH为13．59和臭氧投量为65．08mg／min的条件下，预处理80min后废水COD去除率达63．47％，BOD5／COD由0．03提高至0．56，EC50从11％提高至55％。随着叔丁醇浓度的增加，废水COD去除率明显降低，证明该反应体系有·OH存在；体系中加入MnO2后废水COD去除率下降了16％，氧化效率明显下降，证明该反应体系内中间产物HO2O在O3／UV降解有机废水过程中起到了重要的作用。     

臭氧光催化降解水中甲醛的研究

研究比较了3种光化学方法对水中低浓度甲醛的降解效果,考察了初始pH值、甲醛浓度和臭氧投加速率等因素对臭氧光催化(TiO_2/UV/O_3)降解甲醛的影响。结果表明,紫外臭氧(UV/O_3)、光催化(TiO_2/UV)和TiO_2/UV/O_3对甲醛的降解均符合表观一级反应动力学,TiO_2/UV/O_3降解甲醛的一级表观速率常数大于TiO_2/UV与UV/O_3之和,说明臭氧、光催化有明显的协同作用。pH值对臭氧光催化降解甲醛的速率几乎没有影响;甲醛初始浓度增加,表观反应速率常数下降,但甲醛的绝对去除量仍随初始浓度的增加而显著增加;臭氧投加速率增加,降解速率增加。甲醛降解的主要中间产物为甲酸,但甲酸在臭氧光催化反应过程中也快速降解而被矿化,说明臭氧光催化是一种能安全有效去除甲醛的方法。     

光催化-臭氧氧化降解H酸的研究

采用光催化-臭氧氧化技术(催化膜/UV/O3)降解H酸.研究结果表明,光催化与臭氧氧化相结合具有明显的协同作用.实验进一步讨论了臭氧投加量、废水初始pH值和H酸初始浓度对光催化-臭氧氧化降解H酸的影响.降解后的H酸,萘环结构被破坏,可生化性提高.     

附载型复合光催化剂TiO2·SiO2/beads降解有机磷农药

研究以四异丙醇钛 [Ti( iso- O C3 H7) 4]、硅酸乙酯为原料 ,以空心玻璃微球为载体 ,用溶胶—凝胶法制备可漂浮附载型复合光催化剂 Ti O2 · Si O2 / beads的过程 ,利用附载型复合光催化剂降解有机磷农药。结果表明 ,复合型光催化剂 Ti O2 · Si O2 摩尔比存在最佳值 ,n ( Ti O2 ) / m ( Si O2 ) =30 / 70时 ,光催化剂活性最高 ,其活性是同样降解条件下、同样含量 Degussa P- 2 5Ti O2 的 2倍左右。该光催化剂比表面大 ,吸附性强。并用 XRD和 SEM对附载型复合光催化剂进行表征     

Novel imazethapyr detoxification applying advanced oxidation processes

Different degradation methods have been applied to assess the suitability of advanced oxidation process (AOPs) to promote mineralization of imazethapyr [(RS)-5-ethyl-2-(4-isopropyl-4-methyl-5-oxo-2-imidazolin-2-yl)nicotinic acid], a widely used imidazolinone class herbicide, the persistence of which has been demonstrated in surface and ground waters destined to human uses. Independent of the oxidation process assessed, the decomposition of imazethapyr always followed a pseudo-first order kinetic. The direct UV-irradiation (UV) of the herbicide as well as its oxidation with ozone (O?), and hydrogen peroxide tied to UV-irradiation (H?O?/UV) were sufficiently slow to permit the identification of intermediate products, the formation pathway of which has been proposed. Ozonation joined to UV-irradiation (O?/UV), ozonation joined to titanium dioxide photo-catalysis (TiO?/UV+O?), sole photo-catalysis (TiO?/UV), and photo-catalysis reinforced with hydrogen peroxide-oxidation (TiO?/UV+H?O?) were characterized by a faster degradation and rapid formation of a lot of small molecules, which were quickly degraded to complete mineralization. The most effective oxidation methods were those using titanium dioxide photo-catalysis enhanced either by ozonation or hydrogen peroxide. Most of all, these last processes were useful to avoid the development of dangerous by-products.     

Decomposition of gas-phase trichloroethene by the UV/TiO2 process in the presence of ozone.

The decomposition of gas-phase trichloroethene (TCE) in air streams by direct photolysis, the UV/TiO2 and UV/O3 processes was studied. The experiments were carried out under various UV light intensities and wavelengths, ozone dosages, and initial concentrations of TCE to investigate and compare the removal efficiency of the pollutant. For UV/TiO2 process, the individual contribution to the decomposition of TCE by direct photolysis and hydroxyl radicals destruction was differentiated to discuss the quantum efficiency with 254 and 365 nm UV lamps. The removal of gaseous TCE was found to reduce by UV/TiO2 process in the presence of ozone possibly because of the ozone molecules could scavenge hydroxyl radicals produced from the excitation of TiO2 by UV radiation to inhibit the decomposition of TCE. A photoreactor design equation for the decomposition of gaseous TCE by the UV/TiO2 process in air streams was developed by combining the continuity equation of the pollutant and the surface catalysis reaction rate expression. By the proposed design scheme, the temporal distribution of TCE at various operation conditions by the UV/TiO2 process can be well modeled.     

Synergy of ozonation and photocatalysis to mineralize low concentration 2,4-dichlorophenoxyacetic acid in aqueous solution

Concentration of 2,4-dichlorophenoxyacetic acid (2,4-D) may affect its degradation kinetics in advanced oxidation systems, and combinations of two or more systems can be more effective for its mineralization at low concentration levels. Degradations and mineralizations of 0.045mM 2,4-D using O(3), O(3)/UV, UV/TiO(2) and O(3)/UV/TiO(2) systems were compared, and influence of reaction temperature on the mineralization in O(3)/UV/TiO(2) system was investigated. 2,4-D degradations by O(3), O(3)/UV and UV/TiO(2) systems were similar to the results of earlier investigations with higher 2,4-D concentrations. The degradations and total organic carbon (TOC) removals in the four systems were well described by the first-order reaction kinetics. The degradation and removal were greatly enhanced in O(3)/UV/TiO(2) system, and further enhancements were observed with larger O(3) supplies. The enhancements were attributed to hydroxyl radical (()OH) generation from more than one reaction pathway. The degradation and removal in O(3)/UV/TiO(2) system were very efficient with reaction temperature fixed at 20 degrees C. It was suspected that reaction temperature might have influenced ()OH generation in the system, which needs further attention.     

光催化降解水体异味物质2-MIB的机理

以水体异味物质2-甲基异莰醇(2-methylisoborneol,2-MIB)为研究对象,在紫外光(λ<380 nm)照射下,探讨TiO2(P25)对2-MIB的光催化降解特性及光化学作用机理。结果表明,UV/TiO2光催化体系可以有效去除水体异味物质2-MIB,紫外光照射60 min,对2-MIB的降解率达95%。同时研究了光催化降解体系介质pH,共存腐殖酸(HA)和过硫酸钾(K2S2O8)对UV/TiO2光催化体系降解2-MIB的影响,发现低浓度HA([HA]≤0.5 mg/L)可以提高2-MIB降解速率,当HA浓度高于0.5 mg/L,2-MIB降解反应受到抑制;同时当加入电子受体K2S2O8后,降解体系中活性物种羟基自由基(.OH)明显增加,提高了TiO2对2-MIB的降解能力。利用苯甲酸荧光光度法和POD-DPD显色法跟踪测定降解过程中羟基自由基(·OH)和过氧化氢(H2O2)的变化,表明光催化反应涉及·OH机理。     

Comparison of the degradation of p-hydroxybenzoic acid in aqueous solution by several oxidation processes

A comparative study is made of 12 methods of chemical oxidation applied to degrading p-hydroxybenzoic acid in aqueous solution. The oxidation processes tested were: UV, O3, UV/TiO2, O3/Fe2+, O3/H2O2, O3/UV, UV/H2O2, H2O2/Fe2+, H2O2/Fe2+/O3, UV/H2O2/O3, H2O2/Fe2+/UV and O3/UV/H2O2/Fe2+. The 12 processes were ranked by reactivity. In a kinetic study, the overall kinetic rate constant was split up into three components: direct oxidation by UV irradiation (photolysis), direct oxidation by ozone (ozonation), and oxidation by free radicals (mainly OH*).     

Comparison of advanced oxidation processes and identification of monuron photodegradation products in aqueous solution

The photodegradation of monuron (3-(4-chlorophenyl)-1,1-dimethylurea) in aqueous solutions under simulated solar irradiation has been conducted by different advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/H(2)O(2)/TiO(2), UV/TiO(2), dark H(2)O(2)/Fe(3+)). The degradation rates were always higher for the homogeneous catalysis in photo-Fenton reactions (UV/H(2)O(2)/Fe(2+)) compared to the heterogeneous photocatalytic systems (TiO(2)/UV and UV/H(2)O(2)/TiO(2)). Optimal concentrations of Fe(2+) and H(2)O(2) for the abatement of the herbicide in the photo-Fenton system were found to be 1 mM Fe(II) and 10 mM H(2)O(2). Several intermediary products were identified using large volume injection micro-liquid chromatography with UV detection (mu-LC-UV), mu-LC-MS and GC-MS techniques and a degradation mechanism has been proposed.     

六氯苯的O3及UV/O3高级氧化降解试验研究

采用O₃、UV/O₃高级氧化法对水中六氯苯（HCB）的降解效果及机理进行了研究，并对结果进行了比较，结果表明，UV本身对HCB的去除率贡献不大，HCB可被O₃、UV/O₃快速降解，即UV＜O₃＜UV/O₃；O₃、UV/O₃作用时，提高体系的初始pH值不利于HCB的降解，在pH＝3，HCB=0.2 mg/L，反应40 min时，HCB的去除可达50%左右，酸性条件下有利于降解反应的进行；无论是O₃单独作用还是UV/O₃联合作用，HCB的降解基本上满足准一级反应动力学规律，如果体系的pH值基本保持恒定，这种规律就更为明显。根据离子色谱(IC)、GC对六氯苯降解中间产物进行了测定，探讨了O₃、UV/O₃降解六氯苯的途径和机理。     

不同高级氧化法对水中低浓度药物甲硝唑降解过程的比较

采用UV、H₂O₂、UV/H₂O₂、Fenton、UV/Fenton和UV/TiO₂方法，对水中低浓度的药物甲硝唑进行降解。通过HPLC和UV-Vis光谱得到的甲硝唑去除率。详细讨论了Fe²⁺、TiO₂和H₂O₂的初始浓度以及溶液的初始pH值对降解效率的影响。结果表明，UV/Fenton和UV/TiO₂ 2种系统对水中低浓度甲硝唑均有很好的去除效果，但前者的光催化效率更高。在甲硝唑浓度=6 μmol/L，H₂O₂和Fe²⁺的初始浓度分别为0.5 mg/L和2.94 μmol/L，pH=4的条件下，UV/Fenton方法对甲硝唑水溶液光催化的最佳效率为95.8%。     

Advanced oxidation of a pulp mill bleaching wastewater.

The degradation, by several advanced oxidation reactions, of a pulp mill ECF bleaching effluent, was studied. The initial biodegradability of the organic matter present in the effluent, estimated as the BOD5/COD, was low (0.3). When the effluent was submitted to ozonation and to five different advanced oxidation systems (O3/UV, O3/UV/ZnO, O3/UV/TiO2, O2/UV/ZnO, O2/UV/TiO2), the biodegradability increase significantly. After five minutes of reaction, the O3/UV system appears as the most efficient in to transform the organic matter to more biodegradable forms. A similar effect was observed when the effluent was submitted to an activated sludge treatment. The COD, TOC and toxicity reduction correlated well with the biodegradability enhancement after AOPs treatments.