A comparative study on the properties,mechanisms and process designs for the adsorption of non-ionic or anionic dyes onto cationic-polymer/bentonite

The adsorption properties and mechanisms of a cationic-polymer/bentonite complex (EPI-DMA/bentonite), prepared from polyepicholorohydrin-dimethylamine and bentonite, for non-ionic dyes (Disperse Blue SBL and Vat Scarlet R) and anionic dyes (Reactive Violet K-3R and Acid Dark Blue 2G) were investigated in this study. The solution pH, presence of salt and surfactant can significantly affect the dye removal efficiency. The equilibrium data were analyzed using the Langmuir and Freundlich models. The Langmuir model is the most suitable to describe non-ionic dye adsorption, but for anionic dyes the Freundlich model is best. The kinetic data for the adsorption of different dyes were analyzed using pseudo first- and second-order equations, and the experimental data conformed to the pseudo second-order kinetic model better. The possibility of intraparticle diffusion was also examined by using the intraparticle diffusion equation. The single-stage batch adsorber design for the adsorption of both types of dyes onto EPI-DMA/bentonite was studied based on the Langmuir isotherm model for non-ionic dyes and the Freundlich isotherm model for anionic dyes. The results showed that the required amount of EPI-DMA/bentonite for 95% dye removal in 5 L dye solution with a concentration of 50 mg/L is 378.0 g for DB SBL, 126.5 g for VS R, 9.7 g for RV K-3R and 15.5 g for ADB 2G.     

草木灰对亚甲基蓝的吸附研究

本实验目的是研究草木灰对吸附亚甲基蓝的去除效果,探讨了亚甲基蓝初始量、吸附时间、pH值等对吸附效果的影响,并运用伪一级、伪二级反应动力学模型和Laugmuir、Freundlich等温线模型进行拟合。结果表明,草木灰对亚甲基蓝溶液的吸附在5 min~30 min速率比较快,约在65 min内达到吸附平衡,pH越大越有利于吸附,浓度在5mg/L时草木灰对亚甲基蓝的吸附最佳。与伪二级动力学曲线模型拟合效果较好,由Laugmuir等温线模型计算得出理论最大吸附容量Qm为2.275 mg/g,吸附性能优异。     

Adsorption studies of hazardous malachite green onto treated ginger waste

Adsorption of malachite green (MG) from aqueous solution onto treated ginger waste (TGW) was investigated by batch and column methods. The effect of various factors such as initial dye concentration, contact time, pH and temperature were studied. The maximum adsorption of MG was observed at pH 9. Langmuir and Freundlich isotherms were employed to describe the MG adsorption equilibrium. The monolayer adsorption capacities were found to be 84.03, 163.9 and 188.6 mg/g at 30, 40 and 50 °C, respectively. The values of thermodynamic parameters like ΔG°, ΔH° and ΔS° indicated that adsorption was spontaneous and endothermic in nature. The pseudo second order kinetic model fitted well in correlation to the experimental results. Rechienberg's equation was employed to determine the mechanism of adsorption. The results indicated that film diffusion was a major mode of adsorption. The breakthrough capacities were also investigated.     

Exploitation of Trichoderma harzianum mycelial waste for the removal of rhodamine 6G from aqueous solution

The harvested mycelial waste of Trichoderma harzianum was used as an adsorbent for the removal of rhodamine 6G and was studied in batch mode. The effects of agitation time and initial dye concentration, adsorbent dosage and pH were examined. The study revealed that the amount of dye adsorbed (mgg(-1)) increased with increase in agitation time and reached equilibrium after 120 min, for dye concentrations of 10-50 mg L(-1). The adsorbent dosage of 1.0 g/50 mL and pH of 8.0 were found to be optimum for maximum dye removal. The batch mode adsorption data followed both the Langmuir and Freundlich isotherms. The pseudo first- and second-order rate kinetics were applied to the adsorbent system. The adsorption kinetics of rhodamine 6G showed that the pseudo-second-order kinetic model provided the best correlation of the equilibrium data. The study implies that it is possible to develop a dye removal system by using T. harzianum biomass, which occurs as sludge in waste stream of fermentation industries.     

Adsorption of eosin dye on activated carbon and its surfactant based desorption

The performance of activated carbon has been investigated for the adsorption of eosin dye dissolved in water. Eosin is anionic in nature and highly toxic. The effects of initial dye concentration, contact time, pH and temperature on adsorption of eosin by a fixed amount of activated carbon (1.0 g/L) have been studied in batch and column mode. The equilibrium data are successfully fitted to the Freundlich adsorption isotherm. The adsorption rate data are successfully explained by a pseudo second-order kinetic model. Breakthrough curves for column adsorption have also been studied. The regeneration of spent carbon by desorbing the dye has been experimentally investigated applying a surfactant enhanced carbon regeneration (SECR) technique using both cationic and anionic surfactants. An empirical kinetic model for dye desorption from the commercial activated carbon (CAC) using different surfactant and desorption techniques, viz. change in pH, has been proposed. The comparison between the model and the experimental results is found to be satisfactory.     

Adsorption of basic dye from aqueous solution onto fly ash

The fly ash treated by H₂SO₄ was used as a low-cost adsorbent for the removal of a typical dye, methylene blue, from aqueous solution. An increase in the specific surface area and dye-adsorption capacity was observed after the acid treatment. The adsorption isotherm and kinetics of the treated fly ash were studied. The experimental results were fitted using Langmuir and Freundlich isotherms. It shows that the Freundlich isotherm is better in describing the adsorption process. Two kinetic models, pseudo-first order and pseudo-second order, were employed to analyze the kinetic data. It was found that the pseudo-second-order model is the better choice to describe the adsorption behavior. The thermodynamic study reveals that the enthalpy (ΔH⁰) value is positive (5.63 kJ/mol), suggesting an endothermic nature of the adsorption.     

Removal of direct red 12B and methylene blue from water by adsorption onto Fe (III)/Cr (III) hydroxide, an industrial solid waste

Removal of direct red 12B and methylene blue by adsorption onto Fe (III)/Cr (III) hydroxide was studied using various parameters such as agitation time, dye concentration, adsorbent dose and pH. Equilibrium adsorption data followed both Langmuir and Freundlich isotherms. Adsorption followed second-order rate kinetics. The Langmuir adsorption capacity (Qo) was found to be 5.0 and 22.8 mg dye per g of the adsorbent for direct red 12B and methylene blue, respectively. Acidic pH was favorable for the adsorption of direct red 12B and basic pH for methylene blue. Desorption studies showed that chemisorption seems to be the major mode of adsorption.     

磁性活性炭吸附苯酚的初步研究

本文研究了磁性活性炭对苯酚的吸附性能;探讨了Cd2＋对苯酚在磁性活性炭上吸附的影响。目的是对磁性活性炭进行研究,以及为在实际废水中吸附处理苯酚提供参考。结果表明,磁性活性炭对苯酚的吸附过程符合拟二级动力学模型,R2为0.9935;与Freundlich吸附模型相比,Langmuir吸附模型能更好地描述磁性活性炭对苯酚的吸附行为;在不影响去除率的情况下,Cd2＋的存在使苯酚吸附处理最佳浓度由30 mg/L增大至50 mg/L;同时,Cd2＋对磁性活性炭和活性炭吸附苯酚分别具有促进和抑制作用。针对苯酚的吸附去除率,当无Cd2＋时,磁性活性炭的比活性炭的低10.65%～20.2%;当有Cd2＋时,磁性活性炭的比活性炭的高0.3%～7.71%。     

Mechanisms and chemistry of dye adsorption on manganese oxides-modified diatomite

The investigations into structural changes which occur during adsorbent modification and the adsorption mechanisms are essential for an effective design of adsorption systems. Manganese oxides were impregnated onto diatomite to form the type known as δ-birnessite. Initial investigations established the effectiveness of manganese oxides-modified diatomite (MOMD) to remove basic and reactive dyes from aqueous solution. The adsorption capacity of MOMD for methylene blue (MB), hydrolysed reactive black (RB) and hydrolysed reactive yellow (RY) was 320, 419, and 204 mg/g, respectively. Various analytical techniques were used to characterise the structure and the mechanisms of the dye adsorption process onto MOMD such as Fourier transform infrared (FTIR), X-ray diffraction (XRD) and atomic absorption spectrometry (A.A.). A small shift to higher values of the d-spacing of dye/MOMD was observed indicating that a small amount of the dye molecules were intercalated in the MOMD structure and other molecules were adsorbed on the external surface of MOMD. Two mechanisms of dye adsorption onto MOMD were proposed; intercalation of the dye in the octahedral layers and adsorption of the dye on the MOMD external surface. Moreover, the results demonstrated that the MOMD structure was changed upon insertion of MB and RY with an obvious decrease in the intensity of the second main peak of the MOMD X-ray pattern.     

Adsorption of methylene blue from aqueous solution by jackfruit (Artocarpus heteropyllus) leaf powder: A fixed-bed column study

Continuous fixed-bed studies were undertaken to evaluate the efficiency of jackfruit leaf powder (JLP) as an adsorbent for the removal of methylene blue (MB) from aqueous solution under the effect of various process parameters like bed depth (5–10 cm), flow rate (30–50 mL/min) and initial MB concentrations (100–300 mg/L). The pH at point of zero charge (pH_PZC) of the adsorbent was determined by the titration method and a value of 3.9 was obtained. A FTIR of the adsorbent was done before and after the adsorption to find the potential adsorption sites for interaction with methylene blue molecules. The results showed that the total adsorbed quantities and equilibrium uptake decreased with increasing flow rate and increased with increasing initial MB concentration. The longest breakthrough time and maximum MB adsorption were obtained at pH 10. The results showed that the column performed well at low flow rate. Also, breakthrough time and exhaustion time increased with increasing bed depth. The bed-depth service time (BDST) model and the Thomas model were applied to the adsorption of MB at different bed depths, flow rates, influent concentrations and pH to predict the breakthrough curves and to determine the characteristic parameters of the column that are useful for process design. The two model predictions were in very good agreement with the experimental results at all the process parameters studied indicating that they were very suitable for JLP column design.     

Removal of basic dye (Astrazon Blue FGRL) using macroalga Caulerpa lentillifera

The macroalga Caulerpa lentillifera was found to have adsorption capacity for a basic dye, Astrazon Blue FGRL. For the whole range of concentrations employed in this work (20-1280 mgl(-1)), the adsorption reached equilibrium within the first hour. The kinetic data corresponded well with the pseudo second-order kinetic model where the rate constants decreased as initial dye concentrations increased. At low dye concentrations (20-80 mgl(-1)), an increase in the adsorbent dosage resulted in a higher removal percentage of the dye, but a lower amount of dye adsorbed per unit mass (q). The adsorption isotherm followed both the Langmuir and Freundlich models within the temperature range employed in this work (18-70 degrees C). The highest maximum adsorption capacity (q(m)) was obtained at 50 degrees C. The enthalpy of adsorption was estimated at 14.87 kJmol(-1) suggesting a chemical adsorption mechanism.     

Biosorption of lead by maize (Zea mays) stalk sponge

This study investigated the removal of Pb(II) from aqueous solutions by a maize (Zea mays) stalk sponge. Equilibrium and kinetic models for Pb(II) sorption were developed by considering the effect of the contact time and concentration at the optimum pH of 6 ± 0.2. The Freundlich model was found to describe the sorption energetics of Pb(II) by Z. mays stalk sponge, and a maximum Pb(II) loading capacity of 80 mg g^?1 was determined. The kinetic parameters were obtained by fitting data from experiments measuring the effect of contact time on adsorption capacity into pseudo-first and second-order equations. The kinetics of Pb(II) sorption onto Z. mays biosorbent were well defined using linearity coefficients (R²) by the pseudo-second-order equation (0.9998). The results obtained showed that Zea may stalk sponge was a useful biomaterial for Pb(II) sorption and that pH has an important effect on metal biosorption capacity.     

Development of activated carbon from Nerium oleander flower and their rapid adsorption of direct and reactive dyes

The present study investigates the thermally activated carbon derived from Nerium oleander flower which was used an adsorbent. Physicochemical properties of Nerium oleander flower carbon (NOFC) were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared for the removal of DTB (Direct Turquoise Blue) and RR-HE7B (Reactive red–HE7B) dyes from aqueous solution. Adsorption studies were carried out with different pH, adsorbent dose, contact time, and initial concentration dye solution. Optimum conditions for maximum removal of DTB and RR-HE7B was achieved to be pH 2 for both dyes, adsorbent dose of 100 mg and equilibrium time of 35 and 60 min, respectively, for NOFC. The maximum adsorption capacity of NOFC was found to be 33.33 and 19.60 mg g^?1, respectively, for the removal of dye solution. The mechanism of adsorption was studied by using different kinetic models and isotherms. The results clearly showed that the NOFC adsorption was fitted to pseudo–first-order for DTB and pseudo–second-order for RR-HE7B. Equilibrium data were well fitted with both isotherm models. According to the results, NOFC can effectively remove DTB and RR-HE7B from aqueous solutions.     

Removal of phosphorus from aqueous solutions using chemically modified sawdust of Aleppo pine (<Emphasis Type="Italic">Pinus halepensis Miller</Emphasis>): kinetics and isotherm studies

In the present study, chemically modified Aleppo pine (Pinus halepensis Miller) sawdust was used for the removal of phosphate from water. Biosorbent preparation process included size fractionation, extraction for surface activation, acid prehydrolysis, and treatment with urea. Sorption of phosphate ions onto biosorbent was studied using the batch technique. The effect of different parameters such as contact time, adsorbate concentration, and temperature was investigated. The adsorption kinetics data were best described by the pseudo-second-order rate equation, and equilibrium was achieved after 40 and 80 min for modified and unmodified sawdust, respectively. The Langmuir and Freundlich equations for describing adsorption equilibrium were applied to data. The constants and correlation coefficients of these isotherm models were calculated and compared. The adsorption isotherms obey the Freundlich equation. The thermodynamic parameters like free energy, enthalpy, and entropy changes for the adsorption of phosphate ions have been evaluated, and it has been found that the reaction was spontaneous and endothermic in nature. The low value of activated energy of adsorption, 3.088–3.540 kJ mol⁻¹, indicates that the phosphate ions are easily adsorbed on the sawdust. Results suggest that the prepared chemically modified Aleppo pine sawdust has potential in remediation of contaminated waters by phosphate.     

Application of a chemically modified green macro alga as a biosorbent for phenol removal

Phenol and substituted phenols are toxic organic pollutants present in tannery waste streams. Environmental legislation defines the maximum discharge limit to be 5–50 ppm of total phenols in sewers. Thus the efforts to develop new efficient methods to remove phenolic compounds from wastewater are of primary concern. The present work aims at the use of a modified green macro alga (Caulerpa scalpelliformis) as a biosorbent for the removal of phenolic compounds from the post-tanning sectional stream. The effects of initial phenol concentration, contact time, temperature and initial pH of the solution on the biosorption potential of macro algal biomass have been investigated. Biosorption of phenol by modified green macro algae is best described by the Langmuir adsorption isotherm model. Biosorption kinetics of phenol onto modified green macro algal biomass were best described by a pseudo second order model. The maximum uptake capacity was found to be 20 mg of phenol per gram of green macro algae. A Boyd plot confirmed the external mass transfer as the slowest step involved in the biosorption process. The average effective diffusion coefficient was found to be 1.44 × 10⁻⁹ cm²/s. Thermodynamic studies confirmed the biosorption process to be exothermic.     

Rice husk ash as an effective adsorbent: evaluation of adsorptive characteristics for Indigo Carmine dye

Present study explored the adsorptive characteristics of Indigo Carmine (IC) dye from aqueous solution onto rice husk ash (RHA). Batch experiments were carried out to determine the influence of parameters like initial pH (pH(0)), contact time (t), adsorbent dose (m) and initial concentration (C(0)) on the removal of IC. The optimum conditions were found to be: pH(0)=5.4, t=8h and m=10.0 g/l. The pseudo-second-order kinetic model represented the adsorption kinetics of IC on to RHA. Equilibrium isotherms were analyzed by Freundlich, Langmuir, Temkin and Redlich-Peterson models using a non-linear regression technique. Adsorption of IC on RHA was favorably influenced by an increase in the temperature of the operation. The positive values of the change in entropy (DeltaS(0)) and heat of adsorption (DeltaH(0)); and the negative value of change in Gibbs free energy (DeltaG(0)) indicate feasible and spontaneous adsorption of IC on to RHA.     

Preparation of novel activated carbons from H2SO4-pretreated corncob hulls with KOH activation for quick adsorption of dye and 4-chlorophenol

Corncob hull was immersed in 25 wt% H(2)SO(4) and was carbonized in an oven at 290 °C for 2h to obtain the char. The char was then activated for 1h at 780 °C by KOH at weight ratio of KOH/char of 2.5, 3.0, and 3.5. SEM photos of the carbons revealed that the cell wall of corncob hull was etched into thin film structure. It was shown that the adsorption isotherms of methylene blue and 4-chlorophenol on the carbons were well fitted by the Langmuir equation. Moreover, the adsorption kinetics could be satisfactorily described by the Elovich equation. The normalized standard deviations are less than 2.8%. The high fraction of adsorption amount adsorbed within 1 min to that at saturation demonstrated the advantage of the prepared activated carbons. The fraction of adsorption amount within 1 min to that at saturation (q(1)/q(mon)) for the adsorption of 4-CP is high up to 0.807. Such quick adsorption behavior was mainly attributed to the presence of the thin film structure of carbons.     

Determination of model parameters for zinc (II) ion biosorption onto powdered waste sludge (PWS) in a fed-batch system

Biosorption of zinc (II) ions onto pre-treated powdered waste sludge (PWS) was investigated using a completely mixed tank operating in fed-batch mode instead of an adsorption column. Experiments with variable feed flow rate (0.05-0.5 L h(-1)), feed Zn(II) ion concentrations (37.5-275 mg L(-1)) and amount of adsorbent (1-6 g PWS) were performed using fed-batch operation at pH 5 and room temperature (20-25 degrees C). Break-through curves describing variations of aqueous (effluent) zinc ion concentrations with time were determined for different operating conditions. Percent zinc removal from the aqueous phase decreased, but the biosorbed (solid phase) zinc ion concentration increased with increasing feed flow rate and zinc concentration. A modified Bohart-Adams equation was used to determine the biosorption capacity of PWS (q'(s)) and the rate constant (K) for zinc ion biosorption. Biosorption capacity (q'(s)=57.7 g Zn kg(-1) PWS) of PWS in fed-batch operation was found to be comparable with powdered activated carbon (PAC) in column operations. However, the adsorption rate constant (K=9.17 m(3) kg(-1) h(-1)) in fed-batch operation was an order of magnitude larger than those obtained in adsorption columns because of elimination of mass transfer limitations encountered in the column operations. Therefore, a completely mixed tank operated in fed-batch mode was proven to be more advantageous as compared to adsorption columns due to better contact between the phases yielding faster adsorption rates.     

Preparation of activated carbons from unburnt coal in bottom ash with KOH activation for liquid-phase adsorption

In this work, unburnt coal (UC) in bottom ash from coal-fired power plants was soaked in KOH solution and activated for 1 h at 780 °C. The yield of activated carbons varied from 47.8 to 54.8% when the KOH/UC weight ratio changed from 2 to 4. Pore properties of these activated carbons including the BET surface area, pore volume, pore size distribution, and pore diameter were characterized based on N₂ adsorption isotherms. It was shown that the isotherms for the adsorption of methylene blue, acid blue 74, and 4-chlorophenol from aqueous solutions on these activated carbons at 30 °C were well fitted by the Langmuir equation (correlation coefficient r² > 0.9968). The adsorption capacities of methylene blue, acid blue 74, and 4-chlorophenol were obtained to be 2.40–2.88, 0.57–1.29, and 2.34–5.62 mmol/g, respectively. Moreover, the adsorption kinetics could be suitably described by the Elovich equation.     

Effects of impurities on the removal of heavy metals by natural limestones in aqueous systems

Effects of impurities on the removal of heavy metals by natural limestones in aqueous solutions were studied by evaluating various factors including limestone concentration, pH, contact time and temperature. Solutions of Pb(II), Cd(II), Cu(II) and Zn(II), prepared from chloride reagents at a concentration of 10 mg/L, were studied in a batch method. Four natural limestone samples, collected from the Campanian-Maastrichtian limestone beds in Tunisia, were used as adsorbents. Sorption experiments indicated that high removal efficiencies could be achieved. Limestone samples containing impurities, such as silica, iron/aluminum oxides and different kinds of clay minerals, demonstrated enhanced sorption capacity, nearing 100% removal in some cases. Kinetic experiments showed that the sorption of metal ions occurred rapidly at a low coverage stage, and that solutions were nearly at equilibrium after 60 min. Data trends generally fit pseudo-second order kinetic, and intra-particle diffusion, models. The following conditions were found to promote optimum, or near-optimum, sorption of heavy metals: 1) contact time of more than 60 min, 2) pH = 5, 3) >3 g/L limestone concentration and 4) T = 35 °C. The results of this study suggest that the limestones from northern Tunisia, that contain higher amounts of silica and iron/aluminum oxides, are promising adsorbents for the effective removal of toxic heavy metals from wastewaters.