Utilization of Arachis hypogaea hull,an agricultural waste for the production of activated carbons to remove phenol from aqueous solutions

Arachis hypogaea hulls, an agricultural waste, were used to prepare activated carbon by chemical activation with zinc chloride under four different activation atmospheres. The most important parameter in chemical activation was found to be the chemical ratio (activating agent/precursor). Carbonization temperature and time are the other two important variables, which had significant effect on the pore structure of carbon. The maximum Brunquer-Emmett-Teller (BET) surface area and micropore volume of the activated carbon was found to be 418 m²/g and 0.28 cm³/g, respectively. The activated carbon developed shows substantial capability to adsorb phenol from aqueous solutions. The kinetic data were fitted to the models of intraparticle diffusion, pseudo-second-order, and Lagergren, and followed more closely the pseudo-second-order chemisorption model. The isotherm equilibrium data were well fitted by the Langmuir and Freundlich models. Solution pH has significant effect on adsorption and the maximum uptake of phenol was reported at pH 3.5.     

Utilization of Arachis hypogaea hull, an agricultural waste for the production of activated carbons to remove phenol from aqueous solutions

Arachis hypogaea hulls, an agricultural waste, were used to prepare activated carbon by chemical activation with zinc chloride under four different activation atmospheres. The most important parameter in chemical activation was found to be the chemical ratio (activating agent/precursor). Carbonization temperature and time are the other two important variables, which had significant effect on the pore structure of carbon. The maximum Brunquer-Emmett-Teller (BET) surface area and micropore volume of the activated carbon was found to be 418 m(2)/g and 0.28 cm(3)/g, respectively. The activated carbon developed shows substantial capability to adsorb phenol from aqueous solutions. The kinetic data were fitted to the models of intraparticle diffusion, pseudo-second-order, and Lagergren, and followed more closely the pseudo-second-order chemisorption model. The isotherm equilibrium data were well fitted by the Langmuir and Freundlich models. Solution pH has significant effect on adsorption and the maximum uptake of phenol was reported at pH 3.5.     

Use of carbonised beet pulp carbon for removal of Remazol Turquoise Blue-G 133 from aqueous solution

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g^?1at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.     

Determination of the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon using thermogravimetric analysis

This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl2 was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl2 were 1.75, 0.688, and 0.230 mg of HgCl2 per gram of powdered activated carbon derived from carbon black at 30, 70, and 150 degrees C for 500 microg/m3 of HgCl2, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer-Emmett-Teller (BET) models were used to simulate the adsorption of HgCl2. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30 degrees C, whereas the Freundlich isotherm fit the experimental results better at 70 and 150 degrees C. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl2 by PAC-derived carbon black favored adsorption at various HgCl2, concentrations and temperatures.     

Multi-component adsorption of copper,nickel and zinc from aqueous solutions onto activated carbon prepared from date stones

The removal of Cu²⁺, Ni²⁺, and Zn²⁺ ions from their multi-component aqueous mixture by sorption on activated carbon prepared from date stones was investigated. In the batch tests, experimental parameters were studied, including solution pH, contact time, initial metal ions concentration, and temperature. Adsorption efficiency of the heavy metals was pH-dependent and the maximum adsorption was found to occur at around 5.5 for Cu, Zn, and Ni. The maximum sorption capacities calculated by applying the Langmuir isotherm were 18.68 mg/g for Cu, 16.12 mg/g for Ni, and 12.19 mg/g for Zn. The competitive adsorption studies showed that the adsorption affinity order of the three heavy metals was Cu²⁺?>?Ni²⁺?>?Zn²⁺. The test results using real wastewater indicated that the prepared activated carbon could be used as a cheap adsorbent for the removal of heavy metals in aqueous solutions.     

Determination of the Adsorption Isotherm of Vapor-Phase Mercury Chloride on Powdered Activated Carbon Using Thermogravimetric Analysis

Abstract

This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl₂ was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl₂ were 1.75, 0.688, and 0.230 mg of HgCl₂ per gram of powdered activated carbon derived from carbon black at 30, 70, and 150 °C for 500 µg/m³ of HgCl₂, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer–Emmett–Teller (BET) models were used to simulate the adsorption of HgCl₂. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30 °C, whereas the Freundlich isotherm fit the experimental results better at 70 and 150 °C. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl₂ by PAC-derived carbon black favored adsorption at various HgCl₂ concentrations and temperatures.     

Kinetic, equilibrium isotherm and thermodynamic studies of Cr(VI) adsorption onto low-cost adsorbent developed from peanut shell activated with phosphoric acid

A particular agricultural waste, peanut shell, has been used as precursor for activated carbon production by chemical activation with H₃PO₄. Unoxidized activated carbon was prepared in nitrogen atmosphere which was then heated in air at a desired temperature to get oxidized activated carbon. The prepared carbons were characterized for surface area, surface morphology, and pore volume and utilized for the removal of Cr(VI) from aqueous solution. Batch mode experiments were conducted to study the effects of pH, contact time, particle size, adsorbent dose, initial concentration of adsorbate, and temperature on the adsorption of Cr(VI). Cr(VI) adsorption was significantly dependent on solution pH, and the optimum adsorption was observed at pH 2. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were used to analyze the kinetic data obtained at different initial Cr(VI) concentrations. The adsorption kinetic data were described very well by the pseudo-second-order model. Equilibrium isotherm data were analyzed by the Langmuir, Freundlich, and Temkin models. The results showed that the Langmuir adsorption isotherm model fitted the data better in the temperature range studied. The adsorption capacity which was found to increase with temperature showed the endothermic nature of Cr(VI) adsorption. The thermodynamic parameters, such as Gibb’s Free energy change (ΔG°), standard enthalpy change (ΔH°), and standard entropy change (ΔS°) were evaluated.     

Chromium removal from water by activated carbon developed from waste rubber tires

Because of the continuous production of large amount of waste tires, the disposal of waste tires represents a major environmental issue throughout the world. This paper reports the utilization of waste tires (hard-to-dispose waste) as a precursor in the production of activated carbons (pollution-cleaning adsorbent). In the preparation of activated carbon (AC), waste rubber tire (WRT) was thermally treated and activated. The tire-derived activated carbon was characterized by means of scanning electron microscope, energy-dispersive X-ray spectroscopy, FTIR spectrophotometer, and X-ray diffraction. In the IR spectrum, a number of bands centred at about 3409, 2350, 1710, 1650, and 1300–1000 cm^?1 prove the present of hydroxyl and carboxyl groups on the surface of AC in addition to C═C double bonds. The developed AC was tested and evaluated as potential adsorbent removal of chromium (III). Experimental parameters, such as contact time, initial concentration, adsorbent dosage and pH were optimized. A rapid uptake of chromium ions was observed and the equilibrium is achieved in 1 h. It was also found that the adsorption process is pH dependent. This work adds to the global discussion of the cost-effective utilization of waste rubber tires for waste water treatment.     

Adsorption of acid dye onto activated carbons prepared from agricultural waste bagasse by ZnCl2 activation

A series of activated carbons were prepared from agricultural waste sugarcane bagasse by chemical activation with zinc chloride (ZnCl2) as an activating agent at 500 degrees C and 0.5 h soaking time. The Langmuir surface area and total pore volume were used to estimate the average pore diameter of the carbon products. The values of the surface area and pore volume increased linearly with increase in the impregnation ratio (IR) up to 100 wt%. The adsorption capacities of the derived adsorbents for Acid Orange 10 were measured at 20 degrees C and 40 degrees C to gain further insights into the acidic surface oxides of the adsorbent from the results of Fourier transform infrared (FTIR) spectroscopy analysis and pH measurement. Adsorption isotherms of the acid dye on adsorbents prepared were determined and correlated with common isotherm equations. It was found that the Langmuir model appears to fit the isotherm data better than the Freundlich model. The physical properties of these adsorbents were consistent with the parameters obtained from the isotherm equations.     

麻质活性炭的制备及其对Cu2＋的吸附研究

以废麻为原料,KOH为活化剂制备粉状活性炭,通过静态吸附实验研究了活性炭对Cu2＋的吸附性能,探讨了溶液起始pH值、活性炭投加量、吸附时间、起始Cu2＋质量浓度等对Cu2＋吸附效果的影响。结果表明,溶液pH和活性炭投加量对吸附效果有较大影响,活性炭对Cu2＋的吸附率在60 min内超过50%,初始浓度在10~50 mg/L时,活性炭对Cu2＋的吸附量与起始浓度近似成正比。采用Langmuir、Freundlich吸附等温式对吸附平衡数据进行了拟合,结果表明吸附等温线符合Frenudlich模型。采用傅立叶红外光谱法（FT-IR）分析了活性炭的表面官能团,分析表明活性炭表面酸性官能团可能是吸附Cu2＋的活性中心。     

Equilibrium studies for the sorption of lead from effluents using chitosan

The sorption of lead ions from aqueous solution onto chitosan has been studied. Equilibrium studies have been carried out to determine the capacity of chitosan for lead ions. The effects of solution pH and chitosan particle size on the sorption capacity have been studied.The experimental data were analyzed using three equilibrium isotherm correlations, namely, Langmuir, Freundlich and Redlich-Peterson equations. The linear correlation coefficients were determined for each isotherm and the Freundlich provided the best fit. In addition, error functions have been used to determine the alternative single component equilibrium isotherm parameters by non-linear regression due to the inherent bias in using the correlation coefficient from the linearization. This technique enables the "best fit" isotherm parameters to be used in the equilibrium equations for the sorption of lead ions on chitosan within the limits and assumptions of the various error analysis methods.     

污泥基活性炭吸附Cu（2＋）的应用研究

以城市污水处理厂剩余污泥为原料,以ZnCl2为活化剂制取污泥基活性炭。以此污泥基活性炭为吸附剂,对含Cu2＋的废水进行了吸附实验研究。考察了溶液pH值、Cu2＋的起始浓度对Cu2＋离子吸附量的影响;利用等温吸附实验作出吸附等温线,并考察了污泥基活性炭吸附剂吸附Cu2＋的动力学方程。实验结果表明,污泥基活性炭对Cu2＋具有良好的吸附性能。吸附的最佳pH值为5;吸附符合Langmuir和Freundlich吸附等温方程,吸附为优惠吸附,吸附量随着吸附质溶液浓度的增加而增大;吸附平衡时间为4 h,吸附动力学符合二级动力学方程。     

污泥基活性炭吸附Cu2+的应用研究

以城市污水处理厂剩余污泥为原料，以ZnCl₂为活化剂制取污泥基活性炭。以此污泥基活性炭为吸附剂，对含Cu²⁺的废水进行了吸附实验研究。考察了溶液pH值、Cu²⁺的起始浓度对Cu²⁺离子吸附量的影响；利用等温吸附实验作出吸附等温线，并考察了污泥基活性炭吸附剂吸附Cu²⁺的动力学方程。实验结果表明，污泥基活性炭对Cu²⁺具有良好的吸附性能。吸附的最佳pH值为5；吸附符合Langmuir和Freundlich吸附等温方程，吸附为优惠吸附，吸附量随着吸附质溶液浓度的增加而增大；吸附平衡时间为4 h，吸附动力学符合二级动力学方程。     

双氯芬酸的吸附去除过程与机制

研究了非甾体抗炎药双氯芬酸的吸附去除过程与机制。对吸附处理效果较好的活性炭与纳米羟基氧化铁（α-FeOOH）进行了比表面积、Zeta电位等表面特性的表征，研究比较了双氯芬酸在活性炭与α—FeOOH2种材料上的吸附去除效果与吸附机制。结果表明，在相同的实验条件下，活性炭与α-FeOOH对双氯芬酸吸附去除率可分别达到97．9％和84．3％；双氯芬酸在活性炭上的吸附主要是由于活性炭较大的比表面积与疏水分配作用，在α-FeOOH上的吸附主要是由于静电引力作用；活性炭与α-FeOOH对双氯芬酸的吸附去除效果均随pH的升高而降低；在pH=6时，活性炭与α-FeOOH对双氯芬酸钠的吸附等温线均符合Langmuir方程，单位饱和吸附量分别为109．98mg／g和58．96mg／g；活性炭对双氯芬酸具有更强的吸附能力。     

Adsorption properties of kaolinite-based nanocomposites for Fe and Mn pollutants from aqueous solutions and raw ground water: kinetics and equilibrium studies

Raw kaolinite was used in the synthesis of metakaolinite/carbon nanotubes (K/CNTs) and kaolinite/starch (K/starch) nanocomposites. Raw kaolinite and the synthetic composites were characterized using XRD, SEM, and TEM techniques. The synthetic composites were used as adsorbents for Fe and Mn ions from aqueous solutions and natural underground water. The adsorption by the both composites is highly pH dependent and achieves high efficiency within the neutral pH range. The experimental adsorption data for the uptake of Fe and Mn ions by K/CNTs were found to be well represented by the pseudo-second-order kinetic model rather than the intra-particle diffusion model or Elovich model. For the adsorption using K/starch, the uptake results of Fe ions was well fitted by the second-order model, whereas the uptake of Mn ions fitted well to the Elovich model rather than pseudo-second-order and intra-particle diffusion models The equilibrium studies revealed the excellent fitting of the removal of Fe and Mn ions by K/CNTs and Fe using K/starch with the Langmuir isotherm model rather than with Freundlich and Temkin models. But the adsorption of Mn ions by K/starch is well fitted with Freundlich rather than Temkin and Langmuir isotherm models. The thermodynamic studies reflected the endothermic nature and the exothermic nature for the adsorption by K/CNTs and K/starch nanocomposites, respectively. Natural ground water contaminated by 0.4 mg/L Fe and 0.5 mg/L Mn was treated at the optimum conditions of pH 6 and 120 min contact time. Under these conditions, 92.5 and 72.5% Fe removal efficiencies were achieved using 20 mg of K/CNTs and K/starch nanocomposites, respectively. Also, K/CNTs nanocomposite shows higher efficiency in the removal of Mn ions as compared to K/starch nanocomposite.     

Adsorption of Cu2+ and methyl orange from aqueous solutions by activated carbons of corncob-derived char wastes

Corncob-derived char wastes (CCW) obtained from biomass conversion to syngas production through corncob steam gasification, which were often discarded, were utilized for preparation of activated carbon by calcination, and KOH and HNO₃ activation treatments, on the view of environment protection and waste recycling. Their adsorption performance in the removal of heavy metal ions and dye molecules from wastewater was evaluated by using Cu²⁺ and methyl orange (MO) as the model pollutant. The surface and structure characteristics of the CCW-based activated carbons (CACs) were investigated by N₂ adsorption, CO₂ adsorption, FT-IR, and He-TPD. The adsorption capacity varied with the activation methods of CACs and different initial solution concentrations, indicating that the adsorption behavior was influenced by not only the surface area and porosity but also the oxygen functional groups on the surface of the CACs. The equilibrium adsorption data were analyzed with the Langmuir, Freundlich, and Temkin isotherm models, and the adsorption kinetics was evaluated by the pseudo-first-order and pseudo-second-order models.     

Removal of arsenic(V) from aqueous solutions using iron-oxide-coated modified activated carbon.

Removal of arsenic(V) from aqueous solutions was evaluated with the following three different sorption materials: coal-based activated carbon 12 x 40 (activated carbon), iron(II) oxide (FeO)/activated carbon-H, and iron oxide. The apparent characteristics and physical chemistry performances of these adsorbents were investigated by X-ray diffraction, nitrogen adsorption, and scanning electronic microscope. Also, batch experiments for arsenic removal were performed, and the effects of pH value on arsenic(V) removal were studied. The results suggest that the main phases of the iron oxide surface are magnetite, maghemite, hematite, and goethite; fine and uniform iron oxide particles can cover activated carbon surfaces and affect the surface area or pore structures of activated carbon; adsorption kinetics obey a pseudo-first-order rate equation; and adsorption capacities of adsorbents are affected by the values of pH. The optimum value of pH for iron oxide lies in a narrow range between 4.0 and 5.5, and arsenic(V) removal by FeO/activated carbon-H is ideal and stable in the pH range 3 to 7, while activated carbon has the lowest adsorption capacity in the entire pH range. Also, the adsorption characteristics of FeO/activated carbon-H composites and virgin activated carbon match well the Langmuir adsorption model, while those of iron oxide fit well the Freundlich adsorption model.     

Removal and recovery of copper and nickel ions from aqueous solution by poly(methacrylamide-co-acrylic acid)/montmorillonite nanocomposites

Nanocomposite hydrogels based on poly(methacrylamide-co-acrylic acid) and nano-sized montmorillonite were prepared by aqueous dispersion and in situ radical polymerization. Optimum sorption conditions were determined as a function of montmorillonite content, contact time, pH, and temperature. The equilibrium data of Cu²⁺ and Ni²⁺ conformed to the Freundlich and Langmuir isotherms in terms of relatively high regression values. The maximum monolayer adsorption capacity of the nanocomposite hydrogel (with 3 wt% montmorillonite content), as obtained from the Langmuir adsorption isotherm, was found to be 49.26 and 46.94 mg g^?1 for Cu²⁺ and Ni²⁺, respectively, at contact time?=?60 min, pH?=?6.8, adsorbent dose?=?100 mg/ml, and temperature?=?318 K. Kinetic studies of single system indicated that the pseudo-second order is the best fit with a high correlation coefficient (R ²?=?0.97–0.99). The result of five times sequential adsorption–desorption cycle shows a good degree of desorption and a high adsorption efficiency.     

矸石基X型分子筛对水中Co2+、Cu2+、Cd2+和Cr3+的去除

以煤矸石为原料,采用碱熔后水热合成法制备X型分子筛并进行XRD、SEM、BET和Zeta电位分析。研究其对水中Co2+、Cu2+、Cd2+和Cr3+4种离子的吸附性能,包括吸附等温线、吸附动力学以及初始金属离子浓度、pH值对吸附性能的影响。所合成的矸石基X型分子筛的BET比表面积为676.02 m2/g,微孔孔容为0.263 cm3/g。吸附实验表明,矸石基X型分子筛能有效去除上述4种离子,同时实现煤矸石的资源化和金属离子的去除。4种离子的平衡吸附量均随初始浓度的增大而增大,相同条件下平衡吸附量的大小顺序为Cd2+>Cr3+>Cu2+>Co2+。准二级动力学模型能很好地描述4种离子的吸附动力行为。Langmuir模型对Co2+、Cu2+和Cd2+吸附的拟合较Freundlich模型高,说明其主要表现为物理吸附过程。4种离子的吸附速率均由液膜扩散和颗粒内扩散共同控制。