Measurement of the biodegradation of starch-based materials by enzymatic methods and composting

The aim of this study was to evaluate the suitability of in vitro enzymatic methods for assaying the biodegradability of new starch-based biopolymers. The materials studied included commercial starch-based materials and thermoplastic starch films prepared by extrusion from glycerol and native potato starch, native barley starch, or crosslinked amylomaize starch. Enzymatic hydrolysis was performed using excessBacillus licheniformis -amylase andAspergillus niger glucoamylase at 37°C and 80°C. The degree of degradation was determined by measuring the dissolved carbohydrates and the weight loss of the samples. Biodegradation was also determined by incubating the samples in a compost environment and measuring the weight loss after composting. The results indicated that the enzymatic method is a rapid means of obtaining preliminary information about the biodegradability of starch-based materials. Other methods are needed to investigate more accurately the extent of biodegradability, especially in the case of complex materials in which starch is blended with other polymers.     

不同碳源对微生物修复石油污染土壤的促进作用

为解决石油污染土壤中以石油为唯一碳源的土著微生物生长缓慢的问题,研究了分别添加玉米淀粉、玉米粉、可溶性淀粉和葡萄糖4种碳源对土样细菌总量和石油烃降解率的影响。研究结果表明：玉米淀粉作为碳源时土样TN和TP的下降幅度均最大;添加玉米淀粉和玉米粉比添加可溶性淀粉和葡萄糖更有利于细菌的生长繁殖;细菌对直链烷烃化合物均具有较好的降解效果,但对较为复杂的芳香烃化合物降解效果较差。降解反应第40天时,分别添加玉米淀粉、玉米粉、可溶性淀粉和葡萄糖的石油烃降解率分别为67.25%、48.60%、46.30%和28.57%。     

Characterization of Chemically Modified Potato Starch Films Through Enzymatic Degradation

The present investigation was undertaken to characterize the biodegradation pattern of chemically modified starch films. Chemically modified starch films obtained by esterification of the hydroxyl groups of the polysaccharide have shown lower water sorption than native starch films, being therefore more attractive for a number of processing applications. However, no systematic study characterizing their biodegradation behavior and comparing it with the degradation pattern of native starch films has still been published. In the current contribution we characterized the enzymatic degradation pattern of three derivatized starch films by use of a commercial α-amylase from Bacillus licheniformis. Optimum degradation conditions were chosen upon assaying the effect of enzyme load and temperature on the reaction course of native starch films. Under the conditions selected, comparison of different derivatization procedures revealed that the starch film modified with octanoyl chloride was enzymatically hydrolyzed at a much higher rate than native starch film. Maleated starch films also showed higher susceptibility to α-amylolytic hydrolysis than native starch, whereas acetylated starch showed a hydrolysis pattern similar to that of native starch. Differences in degradation rates of chemically modified films were explained in terms of their amylose content which promotes dense networks that hinder the access of starch-degrading enzymes.     

Physical properties and biodegradability of blends containing poly(ε-caprolactone) and tropical starches

In order to assess feasibility of tropical starches (sago and cassava starches) as biodegradable plastic materials, blending with poly(-caprolactone) (PCL), a biodegradable polymer, was carried out. It was confirmed that the physical properties (tensile strength and elongation) of PCL/sago and PCL/cassava blends were similar to those of PCL/corn blend, suggesting that sago and cassava starches can also be blended with PCL for production of biodegradable plastic. However, the properties of all PCL/starch blends were still low compared with those of polyethylene. Enzymatic degradability evaluation showed that lipase degradation of PCL and-amylase degradation of starch increased as the starch content in the blend increased. Burial test of the blends for 1, 3, and 5 months was carried out and the rate of degradation of the PCL/sago blend was confirmed to be slower than those of PCL/corn and PCL/cassava blends. Observation of the film blends structure by scanning electron microscope revealed that the starch was dispersed in a PCL continuous phase. Furthermore, changes in the film surface before and after enyzme treatments were observed.     

Degradation of Cellulosic Materials Under the Alkaline Conditions of a Cementitious Repository for Low- and Intermediate-Level Radioactive Waste. II. Degradation Kinetics

The degradation of cellulosic materials, differing mainly in the degree of polymerization and the number of reducing end groups, was studied under the alkaline conditions similar to those existing in a cementitious repository for low- and intermediate-level radioactive waste (pH 13.3, T = 25°C). The kinetics of alkaline degradation (peeling-off reaction) were studied and the data analyzed by the model of Haas et al. [13]. The observed kinetic parameters for the propagation reaction and overall stopping reaction were compared with literature data. Although measured under different experimental conditions, literature data and data from this study show a consistent picture. Differences in the extent of degradation observed for the different cellulosic materials could be satisfactorily explained by differences in reducing end group content and, consequently, by differences in the degrees of polymerization. Besides the number of reducing end groups, the degree of amorphousness also plays an important role. The main degradation products formed under the experimental conditions used are - and -(gluco)isosaccharinic acid. This is in agreement with many other studies on alkaline degradation of cellulose. The two isomers are formed in roughly equal amounts.     

Effect of Starch Granule Size on Viscosity of Starch-Filled Poly(hydroxy ester ether) Composites

The effect of starch granule size on the viscosity of starch-filled poly(hydroxy ester ether) (PHEE) composites was characterized using size-fractionated potato starch, as well as unfractionated starches (rice, corn, wheat, and potato). Potato starch was separated using an air classifier into four particle size fractions: <18 m, 18-24 m, 24-30 m, and >30 m. The starch was dried to a moisture content of 0.5% to minimize moisture effects on composite rheology. PHEE and potato starch were extruded with starch volume fractions of 0.46 and 0.66. Stress relaxation, frequency and strain sweep, and temperature-dependence measurements were carried out. Although small variations in viscosity were seen with the different potato starch fractions, differences were not significant at a volume fraction of 0.46. Viscosity differences between the different particle size fractions were more pronounced at a volume fraction of 0.66. The temperature dependence could be described by an Arrhenius relation, with an apparent activation energy of 84 kJ/mole. At a volume fraction of 0.46, the starch/PHEE viscosities increased in the order potato starch < wheat starch corn starch < rice starch.     

Liquid crystallinity of levan/water/starch solutions

Transmitted light measurements performed with a UV-visible spectrophotometer were used to characterize how starch affects the position of boundaries on the phase diagram for dilute aqueous solutions of levan (a branched polymer of fructose). Data were collected in the range 15 to 70°C; the minimum concentrations required for separation of a nematic phase and the minimum concentration required for a fully nematic solution were identified within this range. While hard interactions (repulsion between rod-like molecular segments) dictate the formation of a liquid crystalline phase at and above ambient temperature in the absence of starch, soft interactions become more significant as solutions are cooled toward ambient when starch is present. Small amounts of starch might be used as a filler to modify the mechanical properties (while retaining the process-related benefits) of levan films cast from liquid crystalline solution.     

Physical state and biodegradation behavior of starch-polycaprolactone systems

The biodegradation behavior of insoluble crystalline polymers depends on both chemical structure and physical state. The physical state is strongly affected by the molding conditions; moreover the presence of natural hydrophylic substances such as starch can further influence the biodegradation process. This paper examines the biotic and abiotic degradation of thick injection-molded parts, made of pure poly--caprolactone (PCL) at different molecular weights, and of PCL in the presence of starch in the case of a commercial grade of Mater-Bi, produced by Novamont. The abiotic degradation was studied at 25 and 50°C, whereas the biotic degradation was followed in conditions of SCAS (semicontinuous activated sludges) at 25 and 50°C, soil burial, and controlled composting. The physical-chemical modifications provoked at the surface and in the bulk of the samples by the different types of degradation were determined by differential scanning calorimetry, viscometric and gravimetric analysis, scanning electron microscopy, and dynamic mechanical analysis. The mechanical modifications induced by the different environments were followed by tensile tests. It was demonstrated that the presence of starch significantly increases the apparent biodegradation rate of PCL, making even thick parts of ZI01U compatible with the composting process.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

Hydrolytic and enzymatic degradation of poly(γ-glutamic acid) hydrogels and their application in slow-release systems for proteins

The hydrolytic and enzymatic degradation of newly developed hydrogels, produced by cross-linking purified poly(-glutamic acid) (PGA) with dihaloalkane compounds, was studied and is reported in this paper. Analysis of hydrolysis of the hydrogel as a function of pH indicated that the hydrolysis occurred slowly at neutral pH, but fast in both acidic and alkaline solutions, while the polymer could be hydrolyzed rapidly only in acidic solutions. The ester bonds were more sensitive to hydrolysis than peptide bonds. The biodegradability of the hydrogel and polymer was further confirmed when enzymatic degradation was studied by three enzymes (cathepsin B, pronase E, and trypsin), which were able to cleave both ester and peptide bonds gradually. A slow-release system for porcine somatotropin (pST) formed by using the hydrogel as matrix to entrap the hormone was evaluatedin vitro andin vivo. Results demonstrated that the hydrogel was able to release the hormone for a period of 20–30 days and indicated its potential application in slow-release systems for bioactive materials, especially macromolecules, such as peptides and proteins.     

Enzymatic Degradation of Cellulose-Based Materials

The biodegradability of cellulose-based materials was compared in the standard Sturm test and by enzymatic hydrolysis. Trichoderma reesei culture filtrate, the purified enzymes endoglucanase I and II from T. reesei, and -glucosidase from Aspergillus niger were used in the experiments. The unpurified Trichoderma reesei culture filtrate was found to contain a mixture of enzymes suitable for cellulose degradation. However, when purified enzymes were used the right balance of the individual enzymes was necessary. The addition of -glucosidase enhanced the enzymatic hydrolysis of cellulose materials when both culture filtrate and purified enzymes were used. In the Sturm test the biodegradability of most of the cellulose materials exceeded 70% carbon dioxide generation, but, in contrast, the biodegradability of the highly substituted aminated cellulose and cellulose acetate was below 10%. The results concerning enzymatic hydrolysis and biodegradability were in good agreement for kraft paper, sausage casing, aminated cellulose, and cellulose acetate. However, diverging results were obtained with cotton fabric, probably as a result of its high crystallinity.     

Evaluation of the Biodegradability of Polyvinyl Alcohol/Starch Blends: A Methodological Comparison of Environmentally Friendly Materials

Polyvinyl alcohol (PVA) and starch are both biodegradable polymers. These two polymers can be prepared as biodegradable plastics that are emerging as one of the environmental friendly materials available now. In this study, after reacting with sodium trimetaphosphate (STMP), modified corn starch was blended with PVA in different ratios by a barbender. Test samples were prepared for mechanical and thermal properties measurements. The surface roughness and morphology of fractured surface of the samples were observed by an atomic force microscopy (AFM) and scanning electron microscope (SEM) measurements. Aqueous degradation by enzyme, water absorption and biodegradability behavior were evaluated for the degradability. The biodegradability of these materials was followed by bio-reactivity kinetics models. Results showed that the addition of modified starch could enhance its water uptake. With an addition of 20 wt% of modified starch, the blend had a maximum weight loss during enzymatic degradation. It was found that the degradability was enhanced with the addition of the starch. Analyzing the results of the biodegradability based on the kinetic models, the growth rate of the microorganism was found to be increasing with the increase of the content of starch in the PVA/starch blends in the first order reaction fashion. In our biodegradability analysis, i.e., based on the China national standards (CNS) 14432 regulations, we estimated the decomposition behavior based on the mentioned first order reaction. We found that the PVA/starch blends would take 32.47, 16.20 and 12.47 years to degrade by 70% as their starch content 0, 20 and 40 wt%, respectively.     

Degradation of poly(β-hydroxyalkanoates) and polyolefin blends in a municipal wastewater treatment facility

Six types of plastics and plastic blends, the latter composed at least partially of biodegradable material, were exposed to aerobically treated wastewater (activated sludge) to ascertain their biodegradability. In one study, duplicate samples of 6% starch in polypropylene, 12% starch in linear low-density polyethylene, 30% polycaprolactone in linear low-density polyethylene, and poly(-hydroxybutyrate-co-hydroxyvalerate) (PHB/V), a microbially produced polyester, were exposed to activated sludge for 5 months, and changes in mass, molecular weight average, and tensile properties were measured. None of the blended material showed any sign of degradation. PHB/V, however, showed a considerable loss of mass and a significant loss of tensile strength. In a second study, PHB/V degraded rapidly, but another type of microbial polymer which forms a thermoplastic elastomer, poly(-hydroxyoctanoate), did not degrade. These results illustrate the potential for disposal and degradation of PHB/V in municipal wastewater.     

Kinetic modeling of enzymatic hydrolysis of pretreated kitchen wastes for enhancing bioethanol production

It is well known that use of low cost and abundant waste materials in microbial fermentations can reduce product costs. Kitchen wastes disposed of in large amounts from cafeterias, restaurants, dining halls, food processing plants, and household kitchens contain high amounts of carbohydrate components such as glucose, starch, and cellulose. Efficient utilization of these sugars is another opportunity to reduce ethanol costs. In this study, the effect of pretreatment methods (hot water, acid solutions, and a control) on enzymatic hydrolysis of kitchen wastes was evaluated using a kinetic modeling approach. Fermentation experiments conducted with and without traditional fermentation nutrients were assessed at constant conditions of pH 4.5 and temperature of 30 °C for 48 h using commercial dry baker’s yeast, Saccharomyces cerevisiae. The control, which involved no treatment, and hot water treated samples gave close glucose concentrations after 6 h. The highest and lowest rates of glucose production were found as 0.644 and 0.128 (h^?1) for the control (or no-pretreated (NPT)) and 1% acid solutions, respectively. The fermentation results indicated that final ethanol concentrations are not significantly improved by adding nutrients (17.2–23.3 g/L). Thus, it was concluded that product cost can be lowered to a large extent if (1) kitchen wastes are used as a substrate, (2) no fermentation nutrient is used, and (3) hydrolysis time is applied for about 6 h. Further optimization study is needed to increase the yield to higher levels.     

Novel synthesis blends between bacterial polyesters and acrylic rubber: A study on enzymatic biodegradation

The biodegradability of a multicomponent system based on biotechnological occurring polyester (poly(-hydroxybutyrate-co--hydroxyvalerate) (PHBV)) with inclusion of acrylate elastomer (polybutylacrylate) (PBA) was investigated. A bacterium which produced extracellular enzymes that degrades PHBV even when blended with PBA was isolated and tentatively designated asAureobacterium saperdae. It was observed, by morphological investigation, that, while the bacterial degradation was permitted for PBA content of 20% by weight, it was inhibited for PBA content of 30%, owing to the occurrence of a rubbery layer that prevents to the bacteria an easy accessibility in the PHBV-rich regions. In fact, owing the bacterial growth, only PHBV was metabolized, whereas no degradation of PBA was detected for blend samples. It was confirmed that the degradation proceeded via surface erosion of PHBV also in the blends. Finally, mechanical tests on PHBV/PBA specimens as a function of degradation extent have shown different behavior of the blends at different the PBA content. Thermal analysis of blends and PHBV has been reported, too     

TPS/PCL Composite Reinforced with Treated Sisal Fibers: Property, Biodegradation and Water-Absorption

Sisal fibers bleached with sodium-hydroxide followed by hydrogen peroxide treatment were incorporated in a thermoplastic starch/ε-polycaprolactone (TPS/PCL) blend via extrusion processing. These samples with smooth and homogenous surfaces were examined for their property, biodegradability and water absorption. Scanning electron microscopy revealed that the fibers were well dispersed in the matrix. In addition, it was found that the fibers and matrices interacted strongly. Blends with 20 % (dry weight-basis) fiber content showed some fiber agglomeration. Whereas blends with 10 % fibers showed increased crystallinity and lower water absorption capacity. The CO₂ evolution study showed that the thermoplastic starch samples without any additives had the highest rate and extent of degradation whereas the neat PCL samples had the lowest degradation rate. Addition of fiber to the TPS/PCL blend exhibited the degradation rates and extents that were somewhere in between the pure TPS and neat PCL. This work demonstrates that TPS/PCL composites reinforced with bleached sisal has superior structural characteristics and water resistance and thus, can be used as polymeric engineering composites for different applications.     

In situ bioremediation of a hydrocarbon polluted site with cyclodextrin as a coadjuvant to increase bioavailability

Bioavailability is one main factor that influences the extent of biodegradation of hydrocarbons. They are very poorly soluble in water and easily adsorbed to clay or humus fractions, so they pass very slowly to the aqueous phase where they are metabolised by microorganisms. Cyclodextrins are natural compounds that form soluble inclusion complexes with hydrophobic molecules and increase degradation rate of hydrocarbons in vitro. In the perspective of an in situ application, we previously checked that -cyclodextrin does not increase eluviation of hydrocarbons through the soil and consequently does not increase the risk of groundwater pollution. The results of an in situ application of -cyclodextrin for bioremediation of a hydrocarbon polluted site are presented. We stated that the combination of bioaugmentation and enhanced bioavailability due to -cyclodextrin was effective for a full degradation.     

Biodegradability of Chemically Modified Starch (RS4)/PVA Blend Films: Part 2

Biodegradable films were successfully prepared by using cornstarch (CS), chemically modified starch (RS4), polyvinyl alcohol (PVA), glycerol (GL), and citric acid (CA). The physical properties and biodegradability of the films using CS, RS4, and additives were investigated. The results of the investigation revealed that the RS4-added film was better than the CS-added film in tensile strength (TS), elongation at break (%E), swelling behavior (SB) and solubility (S). Especially, the RS4/PVA blend film with CA as an additive showed physical properties superior to other films. Furthermore, when the film was dried at low temperature, the properties of the films clearly improved because the hydrogen bonding was activated at low temperature. The biodegradation of films was carried out using the enzymatic, microbiological and soil burial test. The enzyme used in this study was amyloglucosidase (AMG), α-amylase (α-AM) and β-amylase (β-AM). At the enzymatic degradation test, the GL-added films had an approximately 60% degradation, while the CA-added films were degraded about 25%. The low degradation value on CA-added film is attributed to low pH of film added CA that deactivated the enzymatic reaction. The microbiological degradation teat was performed by using Bacillus subtilis and Aspergillus niger.     

Solid State Reactions of Potato Starch with Urea and Biuret

Reaction of granular potato starch with urea and biuret resulted in the formation of products, which were soluble neither in cold nor boiling water. The net reaction was a monosubstitution of the hydrogen atom in one hydroxyl group in each D-glucose unit of starch with the either CO–NH₂ or CO–NH–CO–NH₂ moiety, respectively. Properties of the products, particularly these with urea, depended on the mode of reaction. Reactions were carried out in the microwave oven as well as with convection heating. The products retained the granular form of starch but a vast majority of granules were damaged. -Amylolysis of those materials revealed that their susceptibility to the enzyme increasing in the order: starch-amylolysis with simultaneous insolubility in water make these products suitable as ruminant fodder and, eventually, biodegradable material.     

Effects of washing with water on enzymatic saccharification and d-lactic acid production from steam-exploded sugarcane bagasse

This study investigated the production of d-lactic acid from unutilized sugarcane bagasse using steam explosion pretreatment. The optimal steam pressure for a steaming time of 5?min was determined. The steam-exploded sugarcane bagasse was hydrolyzed using cellulase (Meicelase) and then the hydrolyzate was subjected to fermentation substrate. By enzymatic saccharification using Meicelase, the highest recovery of glucose from raw bagasse, 73.7?%, was obtained at a steam pressure of 20?atm. For extracted residue with water after steam explosion, the glucose recovery increased up to 94.9?% at a steam pressure of 20?atm. These results showed that washing with water is effective in removing enzymatic reaction inhibitors. After steam pretreatment (steam pressure of 20?atm), d-lactic acid was produced by Lactobacillus delbrueckii NBRC 3534 from the enzymatic hydrolyzate of steam-exploded bagasse and washed residue. The conversion rate of d-lactic acid obtained from the glucose concentration was 66.6?% for the hydrolyzate of steam-exploded bagasse without washing with water and 90.0?% for that derived from the extracted residue with water after steam explosion. These results also demonstrated that the hydrolyzate of steam-exploded bagasse (without washing with water) contains fermentation inhibitors and washing with water can remove them.     

Microwave-Assisted Solvent-Free or Aqueous-Based Synthesis of Biodegradable Polymers

Microwave radiation was used as the energy source for various types of chemical derivatizations of polysaccharides and for the synthesis of biodegradable polyesters in solvent-free or aqueous-based reaction systems. A medium to high degree of substitution was obtained for starch acetates, starch succinates, carboxymethyl konjac, aminated starch, and aminated chitosan. Ring-opening polymerization of lactide and -caprolactone proceeded rapidly even at low power output in the presence of tin octanoate catalyst. Complete monomer conversion and high molecular weight were achieved in less than 6 minutes under nonisothermal conditions. The yield rapidly increased with increasing power output and showed no significant change in a wide range of batch sizes. Polycaprolactone was successfully grafted from starch and konjac acetate in 3 minutes, yielding as high as 24% grafting efficiency and 25% grafting degree.