The influence of iron and sulfur mineral fractions on carbon tetrachloride transformation in model anaerobic soils and sediments

The objective of this research was to identify the dissolved species or solid phase mineral fraction(s) best correlated with rates of carbon tetrachloride (CT) reductive transformation in systems modeling sulfate-reducing and iron oxide-rich soils and sediments. We used sulfide (S(-II))-treated goethite as our model system, but also studied Fe(II) and S(-II)-treated goethite, Fe(II)-treated goethite, pure FeS, and Fe(II)-treated FeS in order to isolate and evaluate the influence of different mineral fractions on reaction rates. Initial rates of CT transformation were measured for different pH values and concentrations of added Fe(II), as well as different aging times and conditions. The following dissolved species and iron and sulfur mineral fractions were quantified and compared with CT transformation rates: aqueous Fe(2+) and S(-II), surface associated Fe(II) (including weakly and strongly bound Fe(II)), FeS(s), and Cr(II) reducible solid phase S. Over the pH range of 6-10, CT transformation rates were correlated with surface associated Fe(II), while at pH 8, rates were correlated with weakly bound Fe(II). Aging of S(-II)-treated goethite led to oxidation of surface sulfur and a change in the concentration of weakly bound Fe(II), but did not change the relationship between initial rates and weakly bound Fe(II). The results of this research suggest that surface associated Fe(II) and weakly bound Fe(II) could serve as indicators of the potential for abiotic CT dechlorination in natural soils under sulfate-reducing conditions.     

In situ assessment of microbial sulfate reduction in a petroleum-contaminated aquifer using push-pull tests and stable sulfur isotope analyses

Anaerobic microbial activities such as sulfate reduction are important for the degradation of petroleum hydrocarbons (PHC) in contaminated aquifers. The objective of this study was to evaluate the feasibility of single-well push-pull tests in combination with stable sulfur isotope analyses for the in situ quantification of microbial sulfate reduction. A series of push-pull tests was performed in an existing monitoring well of a PHC-contaminated aquifer in Studen (Switzerland). Sulfate transport behavior was evaluated in a first test. In three subsequent tests, we injected anoxic test solutions (up to 1000 l), which contained 0.5 mM bromide (Br-) as conservative tracer and 1 mM sulfate (SO4(2-)) as reactant. After an initial incubation period of 42.5 to 67.9 h, up to 1100 l of test solution/groundwater mixture was extracted in each test from the same location. During the extraction phases, we measured concentrations of relevant species including Br-, SO4(2-) and sulfide (S(-II)), as well as stable sulfur isotope ratios (delta 34S) of extracted, unconsumed SO4(2-) and extracted S(-II). Results indicated sulfate reduction activity in the vicinity of the test well. Computed first-order rate coefficients for sulfate reduction ranged from 0.043 +/- 0.013 to 0.130 +/- 0.015 day-1. Isotope enrichment factors (epsilon) computed from sulfur isotope fractionation of extracted, unconsumed SO4(2-) ranged from 20.2 +/- 5.5@1000 to 22.8 +/- 3.4@1000. Together with observed fractionation in extracted S(-II), isotope enrichment factors provided strong evidence for microbially mediated sulfate reduction. Thus, push-pull tests combined with stable sulfur isotope analyses proved useful for the in situ quantification of microbial sulfate reduction in a PHC-contaminated aquifer.     

Potential for microbially mediated redox transformations and mobilization of arsenic in uncontaminated soils

Surface soil samples, which had no significant As contamination, were examined for As(V) reduction, As(III) oxidation and As mobilization capability. All five soil samples tested exhibited microbial As(V)-reducing activities both in aerobic and anaerobic conditions. Under aerobic conditions when As(V) reduction had almost ceased, oxidation of As(III) to As(V) occurred, whereas only As(V) reduction was observed under anaerobic conditions. In cultures incubated with As(III), As(III) was oxidized by indigenous soil microbes only under aerobic conditions. These results indicate that microbial redox transformations of As are ubiquitous in the natural environment regardless of background As levels. Mobilization through microbially mediated As(V) and Fe(III) reduction occurred both in the presence and absence of oxygen. Significant variation in dissolved As occurred depending on the Fe contents of soils, and re-immobilization of As arose in the presence of oxygen, presumably as a consequence of dissolved As(III) and Fe(II) oxidation. There was no apparent correlation between dissolved Fe(II) and As, suggesting that reductive dissolution of Fe(III) minerals does not necessarily determine the extent of As release from soils.     

Immobilization of uranium and arsenic by injectible iron and hydrogen stimulated autotrophic sulphate reduction

The main object of the study was the development of a long-term efficient and inexpensive in-situ immobilization technology for uranium (U) and arsenic (As) in smaller and decentralized groundwater discharges from abandoned mining processing sites. Therefore, corrosion of grey cast iron (gcFe) and nano-scale iron particles (naFe) as well as hydrogen stimulated autotrophic sulphate reduction (aSR) were investigated. Two column experiments with sulphate reducing bacterias (SRB) (biotic gcFe , biotic naFe) and one abiotic gcFe-column experiment were performed. In the biotic naFe column, no particle translocation was observed and a temporary but intensive naFe corrosion indicated by a decrease in E(h), a pH increase and H(2) evolution. Decreasing sulphate concentrations and (34)S enrichment in the column effluent indicated aSR. Fe(II) retention could be explained by siderite and consequently FeS precipitation by geochemical modeling (PhreeqC). U and As were completely immobilised within the biotic naFe column. In the biotic gcFe column, particle entrapment in open pore spaces resulted in a heterogeneous distribution of Fe-enriched zones and an increase in permeability due to preferential flow. However, Fe(II) concentrations in the effluent indicated a constant and lasting gcFe corrosion. An efficient immobilization was found for As, but not for U.     

Mercury in contaminated sediments and pore waters enriched in sulphate (Tagus Estuary,Portugal)

Three sediment cores, collected nearby the effluent of a chlor-alkali industry, were sliced in 0.5-cm layers and centrifuged for pore water extraction. Mercury, Fe and Mn were determined in the solids as total concentration, hydroxylamine extractable fraction and HCl extractable fraction. Sulphur was determined in the HCl extraction. Total and reactive mercury, chlorinity, S(2-), SO(4)(2-), total Fe, and total Mn were measured in pore waters. The solids contained 3.0-60 nmol g(-1) of total Hg and pore waters 70-5800 pM of total Hg and 1.8-76 pM of reactive mercury. Pore waters presented 2.3-94 times more sulphate than the overlying estuarine waters due to the input from the industry. In layers where hydroxylamine extractable Fe exhibited a broad maximum (precipitation of Fe-oxides) sulphate was reduced to S(2-). The competition between the high content of SO(4)(2-) and Fe(III) as electron acceptors, in chemical reactions occurring in the upper sediments, may explain the co-existence of S(2-) and Fe-oxides in the same layers. Mercury was detected in the hydroxylamine extracts (20-29 nmolg(-1)) in the layers where Fe-oxides were formed, and reactive dissolved Hg showed minimum concentrations. The excess of sulphate in pore waters favoured the abundant Fe-oxides in the upper solid sediments, which appear to work as a barrier limiting the escape of mercury to the water column.     

Reactive transport modelling of biogeochemical processes and carbon isotope geochemistry inside a landfill leachate plume

The biogeochemical processes governing leachate attenuation inside a landfill leachate plume (Banisveld, the Netherlands) were revealed and quantified using the 1D reactive transport model PHREEQC-2. Biodegradation of dissolved organic carbon (DOC) was simulated assuming first-order oxidation of two DOC fractions with different reactivity, and was coupled to reductive dissolution of iron oxide. The following secondary geochemical processes were required in the model to match observations: kinetic precipitation of calcite and siderite, cation exchange, proton buffering and degassing. Rate constants for DOC oxidation and carbonate mineral precipitation were determined, and other model parameters were optimized using the nonlinear optimization program PEST by means of matching hydrochemical observations closely (pH, DIC, DOC, Na, K, Ca, Mg, NH4, Fe(II), SO4, Cl, CH4, saturation index of calcite and siderite). The modelling demonstrated the relevance and impact of various secondary geochemical processes on leachate plume evolution. Concomitant precipitation of siderite masked the act of iron reduction. Cation exchange resulted in release of Fe(II) from the pristine anaerobic aquifer to the leachate. Degassing, triggered by elevated CO2 pressures caused by carbonate precipitation and proton buffering at the front of the plume, explained the observed downstream decrease in methane concentration. Simulation of the carbon isotope geochemistry independently supported the proposed reaction network.     

The effect of silica on the degradation of organohalides in granular iron columns

Dissolved silica species are naturally occurring, ubiquitous groundwater constituents with corrosion-inhibiting properties. Their influence on the performance and longevity of iron-based permeable reactive barriers for treatment of organohalides was investigated through long-term column studies using Connelly iron as the reactive medium. Addition of dissolved silica (0.5 mM) to the column feed solution led to a reduction in iron reactivity of 65% for trichloroethylene (TCE), 74% for 1,1,2-trichloroethane (1,1,2-TCA), and 93% for 1,1,1-trichloroethane (1,1,1-TCA), compared to columns operated under silica-free conditions. Even though silica adsorption was a gradual process, the inhibitory effect was evident within the first week, with subsequent decreases in reactivity over 288 days being relatively minor. Lower concentrations of dissolved silica species (0.2 mM) led to a lesser decrease (70%) in iron reactivity toward 1,1,1-TCA. The presence of dissolved silica species produced a shift in TCE product distribution toward the more highly chlorinated product cis-dichloroethylene (cis-DCE), although it did not appear to alter products originating from the trichloroethanes. The major corrosion products identified were magnetite (Fe3O4) or maghemite (gamma-Fe2O3) and carbonate green rust ([Fe4(2+)Fe(2)3+(OH)12][CO(3).2H2O]). Iron carbonate hydroxide (Fe(II)1.8Fe(III)0.2(OH)2.2CO3) was only found in the silica-free column, indicating that silica may hinder its formation. A comparison with columns operated under the same conditions, but using Master Builder iron as the reactive matrix, showed that Connelly iron is initially less reactive, but performs better than Master Builder iron over 288 days.     

Process-based reactive transport modeling of a permeable reactive barrier for the treatment of mine drainage

Reactive transport modeling of a permeable reactive barrier for the treatment of mine drainage was used to integrate a comprehensive data set including pore water chemistry and solid phase data from several sampling events over a >3-year time period. The simulations consider the reduction of sulfate by the organic carbon-based treatment material and the removal of sulfate and iron by precipitation of reduced mineral phases including iron monosulfides and siderite. Additional parameters constraining the model include dissolved H2S, alkalinity and pH, as well as a suite of solid phase S-fractions identified by extractions. Influences of spatial heterogeneity necessitated the use of a 2-dimensional modeling approach. Simulating observed seasonal fluctuations and long-term changes in barrier reactivity required the use of temperature dependent rate coefficients and a multimodal Monod-type rate expression accounting for the variable reactivity of different organic carbon fractions. Simulated dissolved concentrations of SO4, Fe, H2S, alkalinity and pH, as well as solid phase accumulations of reduced sulfur phases generally compare well to observed trends over 23 months. Spatial variations, seasonal fluctuations and the time-dependent decline in reactivity were also captured. The modeling results generally confirm, and further strengthen, the existing conceptual model for the site. Overall sulfate reduction and S-accumulation rates are constrained with confidence within a factor of 1.5.     

Transport and attenuation of metal(loid)s in mine tailings amended with organic carbon: Column experiments

A laboratory-scale column experiment was conducted to evaluate the effect of organic carbon amendments on the mobility of As, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Tl and Zn in mine tailings. Three columns were packed with sulfide- and carbonate-rich tailings, which were amended with a 1:1 (vol.) mixture of peat and spent brewing grain at proportions of 0, 2 and 5vol.%. A simulated input solution characterized by circumneutral pH and elevated concentrations of SO(4) and S(2)O(3) was passed through the columns for 540 days. The input solution contained low concentrations of metal(loid)s during the initial 300 days and elevated concentrations thereafter. Decreases in mass transport of S(2)O(3) were observed in all columns; with increased attenuation observed at 5 vol. % organic carbon content. Removal of Mn, Ni, Cu, Sb and Mo was observed in all columns during the initial 300 days. However, during this time, mobilization of Fe, As, Zn and Pb was observed, with the greatest increases in concentration observed at the higher organic carbon content. During the final 240 days, S(2)O(3) removal was enhanced in columns containing organic carbon, and Fe, Mn, Ni, Tl, As and Sb removal also was observed. This study demonstrates the influence of organic carbon amendments on metal(loid) mobility in mine tailings. Decreases in mass discharge of metal(loid)s may be achieved using this technique; however, site-specific geochemical conditions must be considered before field-scale implementation.     

Acceleration of the Fe(III)EDTA(-) reduction rate in BioDeNO(x) reactors by dosing electron mediating compounds

BioDeNO(x), a novel technique to remove NO(x) from industrial flue gases, is based on absorption of gaseous nitric oxide into an aqueous Fe(II)EDTA(2-) solution, followed by the biological reduction of Fe(II)EDTA(2-) complexed NO to N(2). Besides NO reduction, high rate biological Fe(III)EDTA(-) reduction is a crucial factor for a succesful application of the BioDeNO(x) technology, as it determines the Fe(II)EDTA(2-) concentration in the scrubber liquor and thus the efficiency of NO removal from the gas phase. This paper investigates the mechanism and kinetics of biological Fe(III)EDTA(-) reduction by unadapted anaerobic methanogenic sludge and BioDeNO(x) reactor mixed liquor. The influence of different electron donors, electron mediating compounds and CaSO(3) on the Fe(III)EDTA(-) reduction rate was determined in batch experiments (21mM Fe(III)EDTA(-), 55 degrees C, pH 7.2+/-0.2). The Fe(III)EDTA(-) reduction rate depended on the type of electron donor, the highest rate (13.9mMh(-1)) was observed with glucose, followed by ethanol, acetate and hydrogen. Fe(III)EDTA(-) reduction occurred at a relatively slow (4.1mMh(-1)) rate with methanol as the electron donor. Small amounts (0.5mM) of sulfide, cysteine or elemental sulfur accelerated the Fe(III)EDTA(-) reduction. The amount of iron reduced significantly exceeded the amount that can be formed by the chemical reaction of sulfide with Fe(III)EDTA(-), suggesting that the Fe(III)EDTA(-) reduction was accelerated via an auto-catalytic process with an unidentified electron mediating compound, presumably polysulfides, formed out of the sulfur additives. Using ethanol as electron donor, the specific Fe(III)EDTA(-) reduction rate was linearly related to the amount of sulfide supplied. CaSO(3) (0.5-100mM) inhibited Fe(III)EDTA(-) reduction, probably because SO(3)(2-) scavenged the electron mediating compound.     

Geochemistry of high arsenic groundwater in Chia-Nan plain, Southwestern Taiwan: possible sources and reactive transport of arsenic

Major ion, trace element, and stable isotope analyses were performed on groundwater samples collected during November 2005 and 2006 in Chia-Nan plain of southwestern Taiwan to examine As mobilization in aquifers. The high concentrations of As, Fe and Mn in the groundwater is consistent with low Eh values (under moderately reduced state). Moreover, the observed Na/Cl and SO(4)/Cl molar ratios in groundwater demonstrate the influence of seawater intrusion. Seawater intrusion could provide required electron acceptors (i.e., SO(4)) for bacterial sulfate reduction and promote reducing conditions that are favorable for As mobilization. The concurrent increases in the concentrations of Fe and Mn from 2005 to 2006 may be caused by bacterial Fe(III) and Mn(IV) reduction. Geochemical modeling demonstrate that As(III) is the dominant As species and the presence of Fe-bearing carbonates, sulfides, and oxide phases may locally act as potential sinks for As. Mud volcano fluids were also collected and analyzed to assess the possible source of As in the Chia-Nan plain groundwater. The oxygen and hydrogen isotopic signatures indicate that the As-rich mud volcano fluids may have been modified by chemical exchange with (18)O-rich crustal rocks and possibly originated from mixing of deep brines with circulating meteoric water. Thus As in the Chia-Nan plain groundwater may have been evolved from deep crustal fluids or rock sources. The hydrogeochemistry and widespread As enrichment in groundwater of Chia-Nan plain result from multiple processes, e.g., de-watering of deep crustal fluids, seawater intrusion, and biogeochemical cycling of Fe, As, and S in alluvial sediments.     

Performance evaluation of granular iron for removing hexavalent chromium under different geochemical conditions

Long-term column experiments were conducted under different geochemical conditions to estimate the longevity of Fe 0 permeable reactive barriers (PRBs) treating hexavalent chromium (Cr(VI)). Secondary carbonate minerals were precipitated, and their effects on the performance, such as differences in the mechanism for Cr removal and the changes in system hydraulics, were assessed. Sequestration of Cr(VI) occurred primarily by precipitation of Fe(III)-Cr(III) (oxy)hydroxides. Trace amounts of Cr were observed in iron hydroxy carbonate presumably due to substitution of Cr3+ for Fe3+. The formation of Fe(III)-Cr(III) (oxy)hydroxide greatly decreased the reactivity of the Fe 0 and thus resulted in migration of the Cr removal front. Carbonate minerals did not appear to contribute to further passivation with regard to reactivity toward Cr removal; rather, the column receiving high contents of dissolved calcium carbonate showed slightly enhanced Cr removal by means of a higher corrosion rate of Fe 0 and because of sequestration by an iron hydroxy carbonate. Precipitation of carbonates, however, governed other geochemical parameters. The porosity and hydraulic conductivity in the column receiving high contents of dissolved calcium carbonate did not indicate a great loss in system permeability because the accumulation of carbonates declined as the Fe 0 was passivated over time. However, the accumulated carbonates and associated Fe(III)-Cr(III) (oxy)hydroxide could cause problems because the presence of these solids resulted in a decline in flow rate after about 1400 pore volumes of operation.     

Regeneration of iron for trichloroethylene reduction by Shewanella alga BrY

Zero valent iron (ZVI), the primary reactive material in several permeable reactive barriers, is often oxidized to ferrous or ferric iron, resulting in decreased reactivity with time. Iron reducing bacteria can reconvert the ferric iron to its ferrous form, prolonging the reduction of chlorinated organic contaminants. In this study, the reduction of Fe(II,III) oxide and Fe(III) oxide by a strain of iron reducing bacteria of the group Shewanella alga BrY(S. alga BrY) was observed in both aqueous and solid phases. S. alga BrY preferentially reduced dissolved ferric iron over the solid ferric iron. In the presence of iron oxide the Fe(II) ions reduced by S. alga BrY efficiently reduced trichloroethylene (TCE). On the other hand, Fe(II) produced by S. alga BrY covered the reactive surfaces of ZVI iron filings and inhibited the reduction of TCE by ZVI. The formation of precipitates on the iron oxide or Fe0 surface was confirmed by scanning electron microscopy. The results suggest that iron-reducing bacteria in the oxidized Fe0 barriers can enhance the removal rate of chlorinated organic compounds and influence on the long-term performance of Fe0 reactive barriers.     

X-ray absorption and photoelectron spectroscopy investigation of selenite reduction by FeII-bearing minerals

The long-lived radionuclide 79Se is one of the elements of concern for the safe storage of high-level nuclear waste, since clay minerals in engineered barriers and natural aquifer sediments strongly adsorb cationic species, but to lesser extent anions like selenate (SeVIO4(2-)) and selenite (SeIVO3(2-)). Previous investigations have demonstrated, however, that SeIV and SeVI are reduced by surface-associated FeII, thereby forming insoluble Se0 and Fe selenides. Here we show that the mixed FeII/III (hydr)oxides green rust and magnetite, and the FeII sulfide mackinawite reduce selenite rapidly (< 1 day) to FeSe, while the slightly slower reduction by the FeII carbonate siderite produces elemental Se. In the case of mackinawite, both S(-II) and FeII surface atoms are oxidized at a ratio of one to four by producing a defective mackinawite surface. Comparison of these spectroscopic results with thermodynamic equilibrium modeling provides evidence that the nature of reduction end product in these FeII systems is controlled by the concentration of HSe(-); Se0 forms only at lower HSe(-) concentrations related to slower HSeO3(-) reduction kinetics. Even under thermodynamically unstable conditions, the initially formed Se solid phases may remain stable for longer periods since their low solubility prevents the dissolution required for a phase transformation into more stable solids. The reduction by Fe2+-montmorillonite is generally much slower and restricted to a pH range, where selenite is adsorbed (pH < 7), stressing the importance of a heterogeneous, surface-enhanced electron transfer reaction. Although the solids precipitated by the redox reaction are nanocrystalline, their solubility remains below 6.3 x 10(-8) M. No evidence for aqueous metal selenide colloids nor for Se sorption to colloidal phases was found. Since FeII phases like the ones investigated here should be ubiquitous in the near field of nuclear waste disposals as well as in the surrounding aquifers, mobility of the fission product 79Se may be much lower than previously assumed.     

In situ iron activated persulfate oxidative fluid sparging treatment of TCE contamination--a proof of concept study

In situ chemical oxidation (ISCO) is considered a reliable technology to treat groundwater contaminated with high concentrations of organic contaminants. An ISCO oxidant, persulfate anion (S(2)O(8)(2-)) can be activated by ferrous ion (Fe(2+)) to generate sulfate radicals (E(o)=2.6 V), which are capable of destroying trichloroethylene (TCE). The property of polarity inhibits S(2)O(8)(2-) or sulfate radical (SO(4)(-)) from effectively oxidizing separate phase TCE, a dense non-aqueous phase liquid (DNAPL). Thus the oxidation primarily takes place in the aqueous phase where TCE is dissolved. A bench column study was conducted to demonstrate a conceptual remediation method by flushing either S(2)O(8)(2-) or Fe(2+) through a soil column, where the TCE DNAPL was present, and passing the dissolved mixture through either a Fe(2+) or S(2)O(8)(2-) fluid sparging curtain. Also, the effect of a solubility enhancing chemical, hydroxypropyl-beta-cyclodextrin (HPCD), was tested to evaluate its ability to increase the aqueous TCE concentration. Both flushing arrangements may result in similar TCE degradation efficiencies of 35% to 42% estimated by the ratio of TCE degraded/(TCE degraded+TCE remained in effluent) and degradation byproduct chloride generation rates of 4.9 to 7.6 mg Cl(-) per soil column pore volume. The addition of HPCD did greatly increase the aqueous TCE concentration. However, the TCE degradation efficiency decreased because the TCE degradation was a lower percentage of the relatively greater amount of dissolved TCE by HPCD. This conceptual treatment may serve as a reference for potential on-site application.     

Processes controlling the distribution and natural attenuation of dissolved phenolic compounds in a deep sandstone aquifer

Processes controlling the distribution and natural attenuation (NA) of phenol, cresols and xylenols released from a former coal-tar distillation plant in a deep Triassic sandstone aquifer are evaluated from vertical profiles along the plume centerline at 130 and 350 m from the site. Up to four groups of contaminants (phenols, mineral acids, NaOH, NaCl) form discrete and overlapping plumes in the aquifer. Their distribution reflects changing source history with releases of contaminants from different locations. Organic contaminant distribution in the aquifer is determined more by site source history than degradation. Contaminant degradation at total organic carbon (TOC) concentrations up to 6500 mg l(-1) (7500 mg l(-1) total phenolics) is occurring by aerobic respiration NO3-reduction, Mn(IV)-/Fe(III)-reduction, SO4-reduction, methanogenesis and fermentation, with the accumulation of inorganic carbon, organic metabolites (4-hydroxybenzaldehyde, 4-hydroxybenzoic acid), acetate, Mn(II), Fe(II), S(-II), CH4 and H2 in the plume. Aerobic and NO3-reducing processes are restricted to a 2-m-thick plume fringe but Mn(IV)-/Fe(II)-reduction, SO4-reduction, methanogenesis and fermentation occur concomitantly in the plume. Dissolved H2 concentrations in the plume vary from 0.7 to 110 nM and acetate concentrations reach 200 mg l(-1). The occurrence of a mixed redox system and concomitant terminal electron accepting processes (TEAPs) could be explained with a partial equilibrium model based on the potential in situ free energy (deltaGr) yield for oxidation of H2 by specific TEAPs. Respiratory processes rather than fermentation are rate limiting in determining the distribution of H2 and TEAPs and H2 dynamics in this system. Most (min. 90%) contaminant degradation has occurred by aerobic and NO3-reducing processes at the plume fringe. This potential is determined by the supply of aqueous O2 and NO3 from uncontaminated groundwater, as controlled by transverse mixing, which is limited in this aquifer by low dispersion. Consumption to date of mineral oxides and SO4 is, respectively, <0.15% and 0.4% of the available aquifer capacity, and degradation using these oxidants is <10%. Fermentation is a significant process in contaminant turnover, accounting for 21% of degradation products present in the plume, and indicating that microbial respiration rates are slow in comparison with fermentation. Under present conditions, the potential for degradation in the plume is very low due to inhibitory effects of the contaminant matrix. Degradation products correspond to <22% mass loss over the life of the plume, providing a first-order plume scale half-life >140 years. The phenolic compounds are biodegradable under the range of redox conditions in the aquifer and the aquifer is not oxidant limited, but the plume is likely to be long-lived and to expand. Degradation is likely to increase only after contaminant concentrations are reduced and aqueous oxidant inputs are increased by dispersion of the plume. The results imply that transport processes may exert a greater control on the natural attenuation of this plume than aquifer oxidant availability.     

Removing nitric oxide from flue gas using iron(II) citrate chelate absorption with microbial regeneration

The addition of metal chelates such as Fe(II)EDTA or Fe(II)Cit to wet flue gas desulfurization systems has been shown to increase the amount of NO(x) absorption from gas streams containing SO(2). This paper attempts to demonstrate the advantage of not only using Fe(II)Cit chelate to absorb nitrogen oxides from flue gas but also the advantage gained from adding microorganisms to the system. Two distinct classes of microorganisms are needed: denitrifying and iron-reducing bacteria. The presence of oxygen in flue gas will affect the absorption efficiency of NO by Fe(II)Cit chelate. The oxidation of Fe(II) can be slowed with the help of bacteria in two ways: bacteria can serve to directly reduce Fe(III) to Fe(II) or they can serve to keep levels of dissolved oxygen in the solution low. As a result, after NO absorption, Fe(II)(Cit)NO will be reduced by denitrifying bacteria to Fe(II)Cit while Fe(III) is reduced by anaerobic bacteria back to Fe(II). Our experiments have shown that the implementation of our protocol allowed for an NO reduction rate constant increase from standard levels of 0.0222-0.100 m Mh(-1) with inlet NO changed from 250 to 1000 ppm. We have also found that total Fe concentration tends to decrease after prolonged periods of operation due to the loss of some Fe to the formation of Fe(OH)(3) that settles together with the sludge at the bottom of bioreactor tank.     

Iron speciation and hydrogen peroxide concentrations in New Zealand rainwater

Rain was collected on the southern portion of the South Island of New Zealand during the summer of 1999 (January–March) during which time significant losses of ozone and increased UV were reported in the stratosphere over New Zealand. Iron and hydrogen peroxide concentrations were measured in rainwater because these analytes are directly influenced by photochemical processes and therefore are particularly susceptible to increasing UV levels. The absolute concentration of dissolved Fe(II) in New Zealand samples was very similar to summertime rain received in Wilmington, NC however the relative contribution of Fe(II) to total Fe was approximately twice as great in New Zealand samples. The larger percentage of reduced iron may reflect higher UV levels in New Zealand since Fe(II) is generated via photochemical reduction of particulate or dissolved Fe(III). No dissolved Fe(III) was detected in New Zealand rainwater, in contrast to the Wilmington site, where summertime Fe(III) concentrations are approximately equal to Fe(II) concentrations. Summertime hydrogen peroxide concentrations and diel variability in New Zealand were similar to other coastal and marine values in both the northern and southern hemispheres suggesting the increasing UV in New Zealand is not significantly increasing hydrogen peroxide concentrations at this location. Any excess photochemically produced hydrogen peroxide in New Zealand may be consumed through oxidation of Fe(II) which is rapidly reformed from photochemical reduction of Fe(III) by the higher UV levels in New Zealand.     

Mobilization of arsenic in aquifers from the Datong Basin,China: Evidence from geochemical and iron isotopic data

Iron isotope compositions of various Fe pools in aquifer sediments were measured at a known As-contaminated site in the Datong Basin, China. The δ⁵⁶Fe values of HCl-extracted poor-crystalline Fe(III) range widely from ?0.41‰ to 0.36‰. We interpret the low Fe(II)/Fe_Extractable ratios (<50%) and the negative correlation between Fe(II)/Fe_Extractable and δ⁵⁶Fe values in HCl-extracted poor-crystalline Fe to be best explained by redox cycling of Fe induced by microbial Fe(III) reduction. However, the high Fe(II)/Fe_Extractable ratios (?70%) and positive correlation between Fe(II)/Fe_Extractable and δ⁵⁶Fe values for HCl-extracted poor-crystalline Fe indicates production of sulfides (FeSs). The δ⁵⁶Fe values of crystalline Fe(III) extracted by reductant appears to be comparatively small varying from ?0.01‰ to 0.24‰, which is consistent with the δ⁵⁶Fe values for ferric oxides/hydroxides having undergone microbial Fe(III) reduction. The Fe isotope composition of various Fe pools shows the transformation between crystalline Fe(III) and poor-crystalline crystalline Fe(III) and the secondary Fe(II) phases has already occurred or is occurring in aquifer sediments. More importantly, there is a significant difference in the As concentrations in crystalline Fe(III) oxides/hydroxides and HCl-extracted Fe phases. The concentrations of As range from 1.6 to 29.9 mg kg^?1 and from 0.6 to 3.0 mg kg^?1, for crystalline Fe(III) and HCl-extracted Fe phases respectively. Accordingly, the transformation of Fe minerals induced by microbial Fe(III) reduction can contribute to the mobilization of As. This study is the first to examine the Fe isotope compositions in high As aquifer sediments; the results show that the Fe isotope would be an important tool in demonstrating the enrichment of As in groundwater.