Impact of polycyclic aromatic hydrocarbon emissions from medical waste incinerators on the urban atmosphere

In this study, polycyclic aromatic hydrocarbon (PAH) emissions from two batch-type medical waste incinerators (MWIs), one with a mechanical grate and the other with a fixed grate, both operated by a medical center, were assessed. Both MWIs shared the same air-pollution control devices (APCDs), with an electrostatic precipitator and a wet scrubber installed in series. Results show that when APCDs were used, total PAHs and total benzo[a]pyrene equivalent (total BaP(eq)) emission concentrations of both MWIs were reduced from 2220 to 1870 microg/m3 and 50 to 12.4 microg/m3, respectively. We used the Industrial Source Complex Short Term model (ISCST) to estimate the ground-level concentrations of the residential area and the traffic intersection located at the downwind side of the two MWIs. For the traffic intersection, we found both total PAHs and total BaP(eq) transported from MWIs to both studied areas were not significant. For the residential area, similar results were found when APCDs were used in MWIs. When APCDs were not included, we found that total PAHs transported from MWIs accounted for < 12%, but total BaP(eq) accounted for > 90%, of the on-site measured concentrations. These results suggest that the use of proper APCDs during incineration would significantly reduce the carcinogenic potencies associated with PAH emissions from MWIs to the residential area.     

Characterisation of volatile organic compounds and polycyclic aromatic hydrocarbons in the ambient air of steelworks

Investigations have been undertaken at two integrated steelworks in the UK to characterise airborne organic micro-pollutants and to assess the contribution of iron ore sintering and coke making operations on the air quality. Concentrations of volatile organic compounds (VOCs), namely benzene, toluene and p-xylene, were measured continuously within the boundary of a coking plant using for the first time differential optical absorption spectrometry (DOAS) between 2004 and 2006. Concentrations were obtained along two monitoring paths surrounding the coke plant and the average benzene concentration measured along both paths over the campaign was 28 μg m^?3. Highest benzene concentrations were associated with winds downwind of the coke oven batteries. Concentrations of polycyclic aromatic hydrocarbons (PAHs) in ambient air were measured during 27 consecutive days in 2005 at three different locations on an integrated steelworks. PAH profiles were determined for each sampling point and compared to coke oven and sinter plant emission profiles showing an impact from the steelworks. The mean benzo [a] pyrene concentration determined in the immediate vicinity of the coke ovens downwind from the battery was 19 ng m^?3, whereas for the two other sites average benzo [a] pyrene concentrations were much lower (around 1 ng m^?3). Data were analysed using principal components analysis (PCA) and results showed that coke making and iron ore sintering were responsible for most of the variation in the PAH concentrations in the vicinity of the investigated plant.     

Source apportionment of polycyclic aromatic hydrocarbons in surface soil in Tianjin, China

Principal component analysis and multiple linear regression were applied to apportion sources of polycyclic aromatic hydrocarbons (PAHs) in surface soils of Tianjin, China based on the measured PAH concentrations of 188 surface soil samples. Four principal components were identified representing coal combustion, petroleum, coke oven plus biomass burning, and chemical industry discharge, respectively. The contributions of major sources were quantified as 41% from coal, 20% from petroleum, and 39% from coking and biomass, which are compatible with PAH emissions estimated based on fuel consumption and emission factors. When the study area was divided into three zones with distinctive differences in soil PAH concentration and profile, different source features were unveiled. For the industrialized Tanggu-Hangu zone, the major contributors were cooking (43%), coal (37%) and vehicle exhaust (20%). In rural area, however, in addition to the three main sources, biomass burning was also important (13%). In urban-suburban zone, incineration accounted for one fourth of the total.     

Effects of meteorology on diurnal and nocturnal levels of priority polycyclic aromatic hydrocarbons and elemental and organic carbon in PM10 at a source and a receptor area in Mexico City

PM₁₀ levels of the 16 US-EPA Priority Pollutant polycyclic aromatic hydrocarbons (PAHs) were measured from March 17 to 31, 2003, in 8-h time bins (morning, afternoon and nighttime) at Merced, a source site dominated by vehicular traffic emissions near the center of Mexico City, and at Pedregal, a receptor area located downwind in a residential area of low traffic. Along with PAH, elemental (EC) and organic carbon (OC), mass, and prevailing meteorological parameters were measured. At the source location, measured concentrations of benzo[a]pyrene (BAP), an agent suspected of being carcinogenic to humans and of causing oxidative DNA damage, reached concentrations as high as 2.04 and 2.11 ng m^?3 during the morning of a weekday and the night period of a holiday. Compared with source dominated areas in Central Los Angeles, the BAP levels found in Central Mexico City are approximately 6 times higher. Benzo[ghi]perylene (BGP) levels were, in general, the highest among the target PAH, both at the source (7.2 ng m^?3) and the receptor site (2.8 ng m^?3), suggesting that, at both locations, exhaust emission by light-duty (LD) vehicles is an important contributor to the atmospheric PAH burden. Higher PAH concentrations were observed during the morning period (5:00–13:00 h) at the source and the receptor site. The concentrations of PAHs found predominantly in the particle-phase (MW > 202) correlated well (r = 0.57–0.71) with the occurrence of surface thermal inversions and with mixing heights (r = ?0.57 to ?0.72). Organic and elemental carbon ratios also indicated that Pedregal is impacted by secondary aerosols during the afternoon hours.     

Particulate PAHs observed in the surrounding of a municipal incinerator

An intensive sampling campaign was undertaken in the surroundings of a municipal waste incinerator located in a French great urban centre in order to evaluate the impact of particles emissions on the ambient air and to estimate the exposure levels to toxic or carcinogenic compounds for a population living in the neighbourhood of this incinerator. To minimise the effect of industrial and road activities, sampling was performed during the 2 days of a weekend and on Monday morning. Different operating modes of the incinerator were investigated: (i) normal incinerator functioning and (ii) maintenance activity of the combustion chamber corresponding to the stop and cooling furnace periods. Particulate polycyclic aromatic hydrocarbons (PAHs) and total particulate carbon concentrations were determined in three sites situated, respectively, close to the incinerator, 2 km downwind and 1 km upwind of the plant. In normal operating mode similar concentrations were observed in the three sites. During the furnace stop an increase of total PAH concentrations was observed in the sampling site close to the incinerator. The concentration was 3 times higher than those measured in the other two sampling sites. But this increase was limited in time and in space since this phenomenon is only observed in the vicinity of the incinerator. The study of PAH profiles indicated that Pyrene and Retene showed the highest enhancement of their relative concentrations. The influence of incinerator functioning parameters on the PAHs concentrations is discussed. The furnace temperature and the mode of exhaust fumes seem to be deciding parameters to explain the increase of PAH level in the incinerator site. However, the incinerator emissions remained a minor part of the atmospheric pollution in the urban area.     

Impact of Polycyclic Aromatic Hydrocarbon Emissions from Medical Waste Incinerators on the Urban Atmosphere

Abstract

In this study, polycyclic aromatic hydrocarbon (PAH) emissions from two batch-type medical waste incinerators (MWIs), one with a mechanical grate and the other with a fixed grate, both operated by a medical center, were assessed. Both MWIs shared the same air-pollution control devices (APCDs), with an electrostatic precipitator and a wet scrubber installed in series. Results show that when APCDs were used, total PAHs and total benzo- [a]pyrene equivalent (total BaP_eq) emission concentrations of both MWIs were reduced from 2220 to 1870 µg/m³ and 50 to 12.4 µg/m³, respectively. We used the Industrial Source Complex Short Term model (ISCST) to estimate the ground-level concentrations of the residential area and the traffic intersection located at the down-wind side of the two MWIs. For the traffic intersection, we found both total PAHs and total BaP_eq transported from MWIs to both studied areas were not significant. For the residential area, similar results were found when APCDs were used in MWIs. When APCDs were not included, we found that total PAHs transported from MWIs accounted for <12%, but total BaP_eq accounted for >90%, of the on-site measured concentrations. These results suggest that the use of proper APCDs during incineration would significantly reduce the carcinogenic potencies associated with PAH emissions from MWIs to the residential area.     

The effect of EURO-0 vehicle substitution on polycyclic aromatic hydrocarbon and carbon monoxide concentrations in an urban area

From 1994 to 2003, daily air concentrations of particle-bound polycyclic aromatic hydrocarbons (PAHs) and carbon monoxide (CO) were regularly monitored at two traffic-oriented sampling sites (A and B) in urban Genoa, Italy. The data were used to estimate effects on air quality in real situations due to progressive substitution of EURO-0 vehicles, started in 1993, with less-polluting vehicles (EURO-1, EURO-2), mainly gasoline vehicles with a catalyst. PAH profile classification and diagnostic PAH ratios were used to identify 345 samples of predominantly traffic origin. At both sites, CO and PAH daily concentrations decreased exponentially with time and the apparent half-life values calculated were 6.3 and 5.5 for CO and 3.7 and 3.5 years for PAHs at sites A and B, respectively. At site A, monitored for traffic intensity, multiple regression analyses confirmed that daily PAH and CO concentrations were positively correlated with the number of non-catalytic vehicles estimated to cross this site during sampling and negatively correlated with seasonal variables (air temperature, ozone concentration, relative air humidity). The reduction in air pollution estimated for complete substitution of non-catalytic gasoline vehicles was 89% for BaP, 85% for total PAHs and 69% for CO.     

Fugitive coke oven gas emission profile by continuous line averaged open-path Fourier transform infrared monitoring

Although most coke oven research is focused on the emission of polycyclic aromatic hydrocarbons, well-known carcinogens, little has been done on the emission of volatile organic compounds, some of which are also thought to be hazardous to workers and the environment. To profile coke oven gas (COG) emissions, we set up an open-path Fourier transform infrared (OP-FTIR) system on top of a battery of coke ovens at a steel mill located in Southern Taiwan and monitored average emissions in a coke processing area for 16.5 hr. Nine COGs were identified, including ammonia, CO, methane, ethane, ethylene, acetylene, propylene, cyclohexane, and O-xylene. Time series plots indicated that the type of pollutants differed over time, suggesting that different emission sources (e.g., coke pushing, quench tower, etc.) were involved at different times over the study period. This observation was confirmed by the low cross-correlation coefficients of the COGs. It was also found that, with the help of meteorological analysis, the data collected by the OP-FTIR system could be analyzed effectively to characterize differences in the location of sources. Although the traditional single-point samplings of emissions involves sampling various sources in a coke processing area at several different times and is a credible profiling of emissions, our findings strongly suggest that they are not nearly as efficient or as cost-effective as the continuous line average method used in this study. This method would make it easier and cheaper for engineers and health risk assessors to identify and to control fugitive volatile organic compound emissions and to improve environmental health.     

Characterization and concentrations of polycyclic aromatic hydrocarbons in emissions from different heating systems in Damascus,Syria

Traffic has long been recognized as the major contributor to polycyclic aromatic hydrocarbon (PAH) emissions to the urban atmosphere. Stationary combustion sources, including residential space heating systems, are also a major contributor to PAH emissions. The aim of this study was to determine the profile and concentration of PAHs in stack flue gas emissions from different kinds of space heaters in order to increase the understanding of the scale of the PAH pollution problem caused by this source. This study set out to first assess the characteristics of PAHs and their corresponding benzo[a]pyrene equivalent emissions from a few types of domestic heaters and central heating systems to the urban atmosphere. The study, enabled for the first time, the characterization of PAHs in stationary combustion sources in the city of Damascus, Syria. Nine different types of heating systems were selected with respect to age, design, and type of fuel burned. The concentrations of 15 individual PAH compounds in the stack flue gas were determined in the extracts of the collected samples using high-performance liquid chromatography system (HPLC) equipped with ultraviolet–visible and fluorescence detectors. In general, older domestic wood stoves caused considerably higher PAH emissions than modern domestic heaters burning diesel oil. The average concentration of ΣPAH (sum of 15 compounds) in emissions from all types of studied heating systems ranged between 43?±?0.4 and 316?±?1.4 μg/m³. Values of total benzo[a]pyrene equivalent ranged between 0.61 and 15.41 μg/m³.     

Identification and removal of polycyclic aromatic hydrocarbons in wastewater treatment processes from coke production plants

Identification and removal of polycyclic aromatic hydrocarbons (PAHs) were investigated at two coke plants located in Shaoguan, Guangdong Province of China. Samples of raw coking wastewaters and wastewaters from subunits of a coke production plant were analyzed using gas chromatography–mass spectrometry (GC/MS) to provide a detailed chemical characterization of PAHs. The identification and characterization of PAH isomers was based on a positive match of mass spectral data of sample peaks with those for PAH isomers in mass spectra databases with electron impact ionization mass spectra and retention times of internal reference compounds. In total, 270 PAH compounds including numerous nitrogen, oxygen, and sulfur heteroatomic derivatives were positively identified for the first time. Quantitative analysis of target PAHs revealed that total PAH concentrations in coking wastewaters were in the range of 98.5?±?8.9 to 216?±?20.2 μg/L, with 3-4-ring PAHs as dominant compounds. Calculation of daily PAH output from four plant subunits indicated that PAHs in the coking wastewater came mainly from ammonia stripping wastewater. Coking wastewater treatment processes played an important role in removing PAHs in coking wastewater, successfully removing 92 % of the target compounds. However, 69 weakly polar compounds, including PAH isomers, were still discharged in the final effluent, producing 8.8?±?2.7 to 31.9?±?6.8 g/day of PAHs with potential toxicity to environmental waters. The study of coking wastewater herein proposed can be used to better predict improvement of coke production facilities and treatment conditions according to the identification and removal of PAHs in the coke plant as well as to assess risks associated with continuous discharge of these contaminants to receiving waters.     

PAH air pollution at a Portuguese urban area: carcinogenic risks and sources identification

This study aimed to characterize air pollution and the associated carcinogenic risks of polycyclic aromatic hydrocarbon (PAHs) at an urban site, to identify possible emission sources of PAHs using several statistical methodologies, and to analyze the influence of other air pollutants and meteorological variables on PAH concentrations.The air quality and meteorological data were collected in Oporto, the second largest city of Portugal. Eighteen PAHs (the 16 PAHs considered by United States Environment Protection Agency (USEPA) as priority pollutants, dibenzo[a,l]pyrene, and benzo[j]fluoranthene) were collected daily for 24 h in air (gas phase and in particles) during 40 consecutive days in November and December 2008 by constant low-flow samplers and using polytetrafluoroethylene (PTFE) membrane filters for particulate (PM₁₀ and PM_2.5 bound) PAHs and pre-cleaned polyurethane foam plugs for gaseous compounds. The other monitored air pollutants were SO₂, PM₁₀, NO₂, CO, and O₃; the meteorological variables were temperature, relative humidity, wind speed, total precipitation, and solar radiation. Benzo[a]pyrene reached a mean concentration of 2.02 ng?m^?3, surpassing the EU annual limit value. The target carcinogenic risks were equal than the health-based guideline level set by USEPA (10^?6) at the studied site, with the cancer risks of eight PAHs reaching senior levels of 9.98?×?10^?7 in PM₁₀ and 1.06?×?10^?6 in air. The applied statistical methods, correlation matrix, cluster analysis, and principal component analysis, were in agreement in the grouping of the PAHs. The groups were formed according to their chemical structure (number of rings), phase distribution, and emission sources. PAH diagnostic ratios were also calculated to evaluate the main emission sources. Diesel vehicular emissions were the major source of PAHs at the studied site. Besides that source, emissions from residential heating and oil refinery were identified to contribute to PAH levels at the respective area. Additionally, principal component regression indicated that SO₂, NO₂, PM₁₀, CO, and solar radiation had positive correlation with PAHs concentrations, while O₃, temperature, relative humidity, and wind speed were negatively correlated.     

Sources and seasonal variation of atmospheric polycyclic aromatic hydrocarbons in Dalian,China: Factor analysis with non-negative constraints combined with local source fingerprints

Vapor- and particulate-phase polycyclic aromatic hydrocarbon (PAH) samples were continuously collected at an urban site in Dalian, China, during the heating and non-heating period. There is strong temperature dependence and obvious seasonal trend for atmospheric PAHs, and significant positive correlations of atmospheric PAHs with SO₂ and CO concentrations were observed. Factor analysis model with non-negative constraints (FA–NNC) combined with local and literature PAH source fingerprints was successful in source identification of particulate PAHs in the atmospheric samples. The results suggested that, in heating period, the main pollution sources were identified as coal-fired boiler emission (56%), residential coal combustion (33%) and traffic emissions (11%). As for non-heating period, the main sources were gasoline engine emission, traffic tunnel emission and coal-fired power plant, and the overall source contributions of traffic emission (gasoline engine + traffic tunnel) were 79% and coal-fired power plant 21%. The current results support our previous study and provide new insights. This can be the first attempt to quantitatively apportion air organic pollutants using receptor models combined with local source fingerprints. The source fingerprints can be used as reference data for source apportionment of atmospheric PAHs of China.     

Atmospheric deposition of polycyclic aromatic hydrocarbons to Izmit Bay, Turkey

Wet deposition and dry deposition samples were collected in an urban/industrialized area of Izmit Bay, North-eastern Marmara Sea, Turkey, from September 2002 to July 2003. The samples were analyzed for sixteen polycyclic aromatic hydrocarbon (PAH) compounds by using HPLC-UV technique. Wet and dry deposition concentrations and fluxes of PAHs were determined. The results showed that PAH concentrations were high because of industrial processes, heavy traffic and residential areas next to the sampling site. Total dry deposition flux of the fifteen 3-6 ring PAHs was 8.30 microg m(-2)day(-1), with a range of 0.034-1.77 microg m(-2)day(-1). The total wet deposition flux of the fifteen 3-6 ring PAHs was 1716 microg m(-2) 11 month(-1), with a range of 10-440 microg m(-2) 11 month(-1). Significant seasonal differences were observed in both types of deposition samples. The winter fluxes of total PAHs were 1.5 and 2.5 times greater than those of the warm period for wet and dry deposition samples, respectively. Factor analysis of dry deposition samples and back trajectory analysis of wet deposition samples were also used to characterize and identify the PAH emission sources in this study.     

Reconstructing historical trends of polycyclic aromatic hydrocarbon deposition in a remote area of Spain using herbarium moss material

Herbarium mosses from 1879–1881, 1973–1975 and 2006–2007 were used to investigate the historical changes of atmospheric deposition of polycyclic aromatic hydrocarbons (PAHs) at a remote site in Northern Spain. Natural abundance of nitrogen and carbon isotopes was also measured in order to assess the evolution of emissions from anthropogenic sources. Nitrogen and PAH concentrations as well as δ¹³C and δ¹⁵N ratios were significantly higher in 19th century samples compared to present century samples. Moreover, PAH distribution varied over the centuries, with the trend towards enrichment in light PAHs. The carbon, nitrogen and PAH concentrations measured in the mosses tally with the historical evolution of anthropogenic emissions in the area, mainly influenced by changes in economic activities, domestic heating and road traffic density. Mosses provided by herbaria seem to offer the possibility of studying long-term temporal evolution of atmospheric PAH deposition.     

Polycyclic aromatic hydrocarbons (PAHs) in the aerosol in Beijing, China, measured by aminopropylsilane chemically-bonded stationary-phase column chromatography and HPLC/fluorescence detection

We developed a useful analytical method for the determination of polycyclic aromatic hydrocarbons (PAH) concentrations in the aerosol of China. We used an accelerated solvent extraction (ASE) method for the extraction of PAHs from the aerosol samples, in order to reduce the extraction time and the solvent volume used. The optimum purification method was developed, with aminopropylsilane chemically-bonded stationary-phase column chromatography, in order to remove many co-extractives which cannot be removed by conventional purification methods using silica-gel column chromatography. HPLC/fluorescence detection (FLD) was adopted as the analytical method, because it has very high sensitivity to PAH and it is easy to install, operate, and maintain as compared with GC/MS. With the analytical method developed in this study, the recovery and precision (RSD) for most of the PAHs ranged from 75% to 129% and from 2.8% to 22.7%, respectively. The concentrations of PAHs in the aerosol samples collected from October 2003 to April 2005 in Beijing, China were determined using the newly developed method. SigmaPAHs, which is the sum of the concentrations of all detected PAHs, was 177.8 +/- 239.9 ng m(-3) (n = 64). The SigmaPAHs concentration in the heating season (305.1 +/- 279.0 ng m(-3), n = 33) was 7.2 times higher than that in the non-heating season (42.3 +/- 32.0 ng m(-3), n = 31). These strong seasonal variations in atmospheric PAH concentration are possibly due to coal combustion for residential heating in winter.     

Characterization of PM2.5-bound polycyclic aromatic hydrocarbons in Atlanta—Seasonal variations at urban,suburban, and rural ambient air monitoring sites

Twenty-eight polycyclic aromatic hydrocarbons (PAH) and methylated PAHs (Me-PAH) were measured in daily PM_2.5 samples collected at an urban site, a suburban site, and a rural site in and near Atlanta during 2004 (5 samples/month/site). The suburban site, located near a major highway, had higher PM_2.5-bound PAH concentrations than did the urban site, and the rural site had the lowest PAH levels. Monthly variations are described for concentrations of total PAHs (∑PAHs) and individual PAHs. PAH concentrations were much higher in cold months than in warm months, with average monthly ∑PAH concentrations at the urban and suburban-highway monitoring sites ranging from 2.12 to 6.85 ng m^?3 during January–February and November–December 2004, compared to 0.38–0.98 ng m^?3 during May–September 2004. ∑PAH concentrations were found to be well correlated with PM_2.5 and organic carbon (OC) within seasons, and the fractions of PAHs in PM_2.5 and OC were higher in winter than in summer. Methyl phenanthrenes were present at higher levels than their un-substituted homologue (phenanthrene), suggesting a petrogenic (unburned petroleum products) input. Retene, a proposed tracer for biomass burning, peaked in March, the month with the highest acreage and frequency of prescribed burning and unplanned fires, and in December, during the high residential wood-burning season, indicating that retene might be a good marker for burning of all biomass materials. In contrast, potassium peaked only in December, indicating that it might be a more specific tracer for wood-burning.     

Obtaining polycyclic aromatic hydrocarbon concentration ratios and molecular markers for residential wood combustion: Temuco, a case study

It is known that residential wood combustion (RWC) is an important source of fine particle emissions. The purpose of this work was to characterize the chemical composition of the particulate matter present in the Temuco urban atmosphere during winter, specifically the polycyclic aromatic hydrocarbon (PAH) profile, because PAHs are considered to be among the key compounds in particulate matter toxicity. During the 2008 winter monitoring campaign, samples of particulate matter with aerodynamic diameters of < or = 10 (PM10) and < or = 2.5 (PM2.5) microm were taken on days with contamination episodes. Sixteen U.S. Environmental Protection Agency (EPA) PAH compounds were extracted with toluene and determined by gas chromatography-mass spectrometry (GC-MS). The results show that phenantrene was the predominant compound associated with particulate matter at a concentration range between 300 and 600 ng m(-3), 18 times higher than the second most abundant PAH compound. High-molecular-mass compounds such as dibenz[a,h]anthracene, benzo[g,h,i]perylene, and indeno[1,2,3,c,d]pyrene were also found, but they were minorities in the set. It was recognized from the PAH concentration ratios of the Temuco atmospheric aerosol that the main contamination source was in fact residential wood combustion; although not all the concentration ratios evaluated match the reported reference values, probably due to the kind of biomass used, the characteristics of Chilean heating appliances and climate.     

Levels of PAHs in soil and vegetation samples from Tarragona County, Spain

The levels of 16 polycyclic aromatic hydrocarbons (PAHs) were determined in 24 soil and 12 wild chard samples collected in Tarragona County (Catalonia, Spain), an area with an important number of chemical and petrochemical industries. Samples were also collected in urban/residential zones and in presumably unpolluted sites (control samples). In soils, the sum of the 16 PAHs ranged between 1002 and 112 ng/g (dry weight) for samples collected near chemical industries and unpolluted sites, respectively. With the exception of acenaphthylene, acenaphthene, anthracene and benzo[k]fluoranthene, no significant differences in the levels of the remaining PAHs were found among the different zones of sample collection. In chard samples, the highest value (sum of 16 PAHs) was observed in the residential area, followed by the industrial and the unpolluted zones, with concentrations of 179, 58 and 28 ng/g (dry weight), respectively. In general terms, the current PAH concentrations in soil and vegetation are lower than the levels reported in a number of investigations from different regions and countries. They are also below the maximum PAH concentrations allowed by the Catalan legislation for different uses of soil.     

Measured summertime concentrations of particulate components,Hg0, and speciated polycyclic aromatic hydrocarbons at rural sites in New York State

Daily PM2.5 samples, Hg0 and speciated polycyclic aromatic hydrocarbon (PAH) were simultaneously collected at Potsdam and Stockton site in NY during the summers of 2000 and 2001. Samples for determination of the mass concentration and chemical composition of the PM2.5 were obtained with a speciation network PM2.5 sampler. Chemical composition including trace elemental composition, water-soluble ions, and elemental carbon were analyzed. Elemental mercury and PAHs were sampled separately. Daily PM2.5 concentrations ranged from 0.47 to 53.7 microg m(-3) at the Potsdam site, and from 0.82 to 47.23 microg m(-3) at the Stockton site with large daily differences between the two sites. Potsdam consistently had lower mass values than Stockton. The greatest contributors to the PM2.5 mass (generally >0.1 microg/m(3)) were sulfate, nitrate, ammonium, and BC at both sites. Seventeen PAHs were identified at each site in 2000 and the average total concentrations were 3.2 ng/m(3) and 2.9 ng/m(3) at the Potsdam and Stockton sites, respectively. The mean vapor phase mercury concentration at the Potsdam site (2.4 +/-1.2 ng m(-3), n=93) was higher than that at the Stockton site (1.2 +/- 1.0 ng m(-3), n=60) in 2000, whereas in 2001, the average concentrations were 1.1 ng m(-3) and 1.6 ng m(-3) at the Potsdam and Stockton sites, respectively. In general, vapor phase mercury concentrations increased with increasing ambient temperature at the Stockton site in 2000. These differences in values between 2000 and 2001 can be largely explained by distinct differences in the meteorological regimes that dominated in the different years.     

Field use of semipermeable membrane devices (SPMDs) for passive air sampling of polycyclic aromatic hydrocarbons: Opportunities and limitations

Semipermeable membrane devices (SPMDs) were used for measurements in air of twelve polycyclic aromatic hydrocarbons (PAHs) in two Genoa locations, both on building roofs, distant 300 m from each other. The first, site A, was in front a dismissing steel complex and the second, site B, was in an urban area overlooking a busy thoroughfare. SPMDs were deployed contemporary at the two sites, in nine monthly samplings, from April 2007 to May 2008. The amount of sequestered PAHs, in sites A and B, ranged between 61–267 ng SPMD^?1 d^?1 and 50–535 ng SPMD^?1 d^?1, respectively.PAHs profiles highlighted seasonal differences and suggested the possible role of different PAHs sources in the two areas. In particular, the contribution of remediation works of the steel complex was observed in site A. Moreover, a naphthalene leak from a tank, into the former industrial area, and a fire broke out near site A, were registered by time-integrated measurements of SPMDs.However, the strong dependence between amount of sequestered PAHs and air temperature needs further studies to distinguish between uptake rate variability and seasonal contribution of different sources. Finally, to measure air concentrations with reasonable accuracy, it should be very important to have certified sampling rates for all individual PAHs.