MTBE in California Drinking Water: An Analysis of Patterns and Trends

Over the past decade, there has been much publicity surrounding the impact of Methyl tert -butyl ether (MTBE) on drinking water supplies in the United States. In California, the presence of MTBE in groundwater and drinking water has led to a ban on the future use of MTBE in gasoline. Other states, such as those in the northeast, are also seeking ways to reduce or eliminate the use of MTBE due to perceived threats to the environment and public health. Despite claims about the incidence of MTBE in drinking water, no comprehensive characterization has been conducted on the available drinking water monitoring data. This paper provides a detailed analysis of the MTBE drinking water data compiled by the California Department of Health Services (CDHS) from 1995 to 2000. We find that MTBE was detected in about 1.3% of all drinking water samples, 2.5% of drinking water sources, and 3.7% of drinking water systems in California over this 6-year period. Our analysis reveals that many drinking water sources are not sampled routinely for MTBE, and in those sources that appear to be affected by MTBE, the compound is not consistently detected. The majority of MTBE detections are also concentrated in several geographic areas, which contain about 9–21% of the total California population. Average detected MTBE concentrations have decreased significantly since 1995 and 1996, ranging from 5 to 15 ppb over the last 3 years depending on the outcome of interest. Of the samples in which MTBE was present above the analytical detection limit, the concentrations in approximately 73% of drinking water samples and 86% of drinking water sources and systems were below the State's primary health-based standard of 13 ppb. Our findings suggest that, although some drinking water supplies in California have been affected by MTBE, the majority of drinking water sources and systems either have not been affected at all or contain MTBE at concentrations below levels that are likely to be of health concern.     

MTBE in California's Drinking Water: A Comparison of Groundwater Versus Surface Water Sources

During the last decade, the fuel oxygenate methyl tertiary butyl ether (MTBE) has received widespread attention as a potential threat to water quality, primarily due to leaking underground gasoline storage tanks and watercraft with two-stroke engines. In this article, we examine the annual detection frequency, number of new source detections, and concentration of MTBE detected in California's public drinking water groundwater and surface water sources from 1995 to 2002. This work builds on our previous evaluations of California's water quality monitoring database. However, it is unique in that it includes separate evaluations for groundwater and surface water sources that are of greatest concern to regulators, and which are likely being used for current public consumption. Our evaluations also include full-year data for 2002 (which have not been published previously) and an analysis of how the sampling and reported detections of MTBE vary by geographic location. We find that MTBE was generally detected (at any level) in approximately 0.5-0.9% and 0.2-0.4% of all groundwater sources assuming a one-detection and two-detection criterion, respectively. The overall detection frequency for MTBE in surface water sources is significantly higher than for groundwater sources, although these surface water detections appear to have substantially declined since 1996 (e.g., 7-9% for all surface water sources during 1996 to 1999 and 4% for all surface water sources during 2000 to 2002, assuming a one-detection criterion). The detection frequency of MTBE concentrations at or above the state drinking water standards in all drinking water sources (both groundwater and surface water sources) and the subset of drinking water sources that are likely to currently be delivered to consumers is markedly lower (and often zero). Despite the significant increase in water sampling over time, the number of new drinking water sources found to contain MTBE in California has not increased at the same rate and appears to have remained relatively stable or to have decreased since 1998. The data also show that nearly all of the 58 counties in California have routinely sampled at least some of their groundwater and surface water sources for MTBE over the last 8 years. Geographical evaluations show that MTBE has been detected (at least once) in groundwater sources in 34 counties and in surface water sources in 18 counties but has only been detected routinely (i.e., for 3 or more years) in 16 and 7 counties, respectively. Detected concentrations of MTBE are also generally below state drinking water standards, particularly for surface water sources. In short: (1) MTBE is rarely found in California groundwater or surface water sources that are of greatest concern to regulators or the public, and (2) drinking water detections of MTBE are expected to decline in the future due to the pending phase-out of MTBE and recent regulatory programs aimed at controlling gasoline releases from underground storage tanks and two-stroke-engine watercraft.     

Methyl tert-butyl ether (MTBE) in finished drinking water in Germany

In the present study 83 finished drinking water samples from 50 cities in Germany were analyzed for methyl tert-butyl ether (MTBE) content with a detection limit of 10 ng/L. The detection frequency was 46% and the concentrations ranged between 17 and 712 ng/L. Highest concentrations were found in the community water systems (CWSs) of Leuna and Spergau in Saxony-Anhalt. These CWSs are supplied with water possibly affected by MTBE contaminated groundwater. MTBE was detected at concentrations lower than 100 ng/L in drinking water supplied by CWSs using bank filtered water from Rhine and Main Rivers. The results from Leuna and Spergau show that large groundwater contaminations in the vicinity of CWSs pose the highest risk for MTBE contamination in drinking water. CWSs using bank filtered water from Rhine and Main Rivers are susceptible to low MTBE contaminations in finished drinking water. All measured MTBE concentrations were below proposed limit values for drinking water.     

Methyl Tertiary Butyl Ether (MTBE) and Other Volatile Organic Compounds (VOCs) in Public Water Systems,Private Wells,and Ambient Groundwater Wells in New Jersey Compared to Regulatory and Human-Health Benchmarks

Potential threats to drinking water and water quality continue to be a major concern in many regions of the United States. New Jersey, in particular, has been at the forefront of assessing and managing potential contamination of its drinking water supplies from hazardous substances. The purpose of the current analysis is to provide an up-to-date evaluation of the occurrence and detected concentrations of methyl tertiary butyl ether (MTBE) and several other volatile organic compounds (VOCs) in public water systems, private wells, and ambient groundwater wells in New Jersey based on the best available data, and to put these results into context with federal and state regulatory and human-health benchmarks. Analyses are based on the following three databases that contain water quality monitoring data for New Jersey: Safe Drinking Water Information System (SDWIS), Private Well Testing Act (PWTA), and National Water Information System (NWIS). For public water systems served by groundwater in New Jersey, MTBE was detected at a concentration ≥10 μg/L, ≥20 μg/L, and ≥70 μg/L at least once in 30 (2%), 21 (1.4%), and five (0.3%) of sampled systems from 1997 to 2011, respectively. For private wells in New Jersey, MTBE was detected at a concentration ≥10 μg/L, ≥20 μg/L, and ≥70 μg/L at least once in 385 (0.5%), 183 (0.2%), and 46 (0.05%) of sampled wells from 2001 to 2011, respectively. For ambient groundwater wells in New Jersey, MTBE was detected at a concentration ≥10 μg/L, ≥20 μg/L, and ≥70 μg/L at least once in 14 (2.1%), 9 (1.3%), and 4 (0.6%) of sampled wells from 1993 to 2012, respectively. Average detected concentrations of MTBE, as well as detected concentrations at upper-end percentiles, were less than corresponding benchmarks for all three datasets. The available data show that MTBE is rarely detected in various source waters in New Jersey at a concentration that exceeds the State's health-based drinking water standard or other published benchmarks, and there is no evidence of an increasing trend in the detection frequency of MTBE. Other VOCs, such as tetrachloroethylene (PCE), trichloroethylene (TCE), and benzene, are detected more often above corresponding regulatory or human-health benchmarks due to their higher detected concentrations in water and/or greater toxicity values. The current analysis provides useful data for evaluating the nature and extent of historical and current contamination of water supplies in New Jersey and potential opportunities for public exposures and health risks due to MTBE and other VOCs on a statewide basis. Additional forensic or forecasting analyses are required to identify the sources or timing of releases of individual contaminants at specific locations or to predict potential future water contamination in New Jersey.     

Nitrogen species in drinking water indicate potential exposure pathway for Balkan Endemic Nephropathy

This study explored two hypotheses relating elevated concentrations of nitrogen species in drinking water and the disease Balkan Endemic Nephropathy (BEN). Drinking water samples were collected from a variety of water supplies in both endemic and non-endemic villages in the Vratza and Montana districts of Bulgaria. The majority of well water samples exceeded US drinking water standards for nitrate + nitrite. No statistically significant difference was observed for any of the nitrogen species between villages classified as endemic and non-endemic. Other constituents (sodium, potassium and chloride) known to be indicators of anthropogenic pollution were also found at elevated concentrations and all followed the order wells > springs > taps. This ordering coincides with the proximity of human influences to the water sources. Our results clearly establish an exposure pathway between anthropogenic activity and drinking water supplies, suggesting that the causative agent for BEN could result from surface contamination.     

Halogenated acetaldehydes: analysis, stability and fate in drinking water

In our previous studies, chloral hydrate has been the only chlorinated acetaldehyde determined in drinking water because authentic standards of other related haloacetaldehydes were not available. Recently, standards of dichloroacetaldehyde, bromochloroacetaldehyde, dibromoacetaldehyde, bromodichloroacetaldehyde, chlorodibromoacetaldehyde, and tribromoacetaldehyde have become available commercially. They were obtained and verified for purity and stability using a dual-column GC-ECD system. Each commercial standard was found to contain small amounts of the other target haloacetaldehydes (HAs). The stability of the HAs stock solutions was solvent dependent: in acetone, the brominated species partially degraded to bromoacetone, while all target HAs were stable in MTBE for up to 8 months. The analytical parameters, required for the quantification of HAs in water, were determined and used to evaluate the stability of the HAs in water. Under the conditions of the sampling protocol (field pH adjustment to pH 4.5 and storage at 4 degrees C), the target HAs were stable in water for up to 14 days. However, at typical drinking water pH and temperature conditions, the stability varied with the HA species, pH, temperature and storage period. The trihalogenated acetaldehydes degraded, in part, to their corresponding trihalomethanes (THMs) at increasing pH and temperature. Most target HAs were detected in drinking water samples collected from various Canadian drinking water systems, and the speciation was dependent on water parameters (e.g. bromide concentration) and treatment processes. From the water samples analysed, chloral hydrate ranged between 7% and 51% of the total HAs (w/w). The weigh ratio of total HAs to total THMs (10-46%) indicated that HAs contributed significantly to the pool of DBPs in drinking water.     

Toxicity of methyl-tert-butyl ether to freshwater organisms

Increased input of the fuel oxygenate methyl-tert-butyl ether (MTBE) into aquatic systems has led to concerns about its effect(s) on aquatic life. As part of a study conducted by University of California scientists for the State of California, the Aquatic Toxicology Laboratory, UC Davis, reviewed existing literature on toxicity of MTBE to freshwater organisms, and new information was generated on chronic, developmental toxicity in fish, and potential toxicity of MTBE to California resident species. Depending on time of exposure and endpoint measured, MTBE is toxic to various aquatic organisms at concentrations of 57-> 1000 mg/l (invertebrates), and 388-2600 mg/l (vertebrates). Developmental effects in medaka (Oryzias latipes) were not observed at concentrations up to 480 mg/l, and all fish hatched and performed feeding and swimming in a normal manner. Bacterial assays proved most sensitive with toxicity to Salmonella typhimurium measured at 7.4 mg/l within 48 h. In microalgae, decreased growth was observed at 2400 and 4800 mg/l within 5 days. MTBE does not appear to bioaccumulate in fish and is rapidly excreted or metabolized. Collectively, the available data suggests that at environmental MTBE exposure levels found in surface waters (< 0.1 mg/l) this compound is likely not acutely toxic to aquatic life. However, more information is needed on chronic and sublethal effects before we can eliminate the possibility of risk to aquatic communities at currently detected concentrations.     

Effect of pesticide use in fruit production orchards on shallow ground water

As a part of landscape-scale study, ground water samples were collected from 30 wells located in fruit production farms belonging to the valley of Neuquen river during the period 1995-1998 and analyzed for organophosphate pesticides. As a consequence of the leaching process, ground water from the Valley of Neuquen River frequently contained concentrations of organophosphorus pesticides that exceeded acute toxicity risk ratios established to protect aquatic life. It was found that some pesticides, as azinphos methyl, had a high detection frequency, 66% of the samples, with concentrations varying from no detection to 48.9 ppb. Dimethoate, metidathion and phosmet were also detected with frequencies of 14.1, 13.6 and 10.8% and with concentration ranks from no detection to a maximum value of 10.9, 2.0 and 15.5 ppb, respectively. Seasonal variations and temporal trends were found for these compounds in ground water.     

MTBE oxidation byproducts from the treatment of surface waters by ozonation and UV-ozonation

In recent years, there has been considerable concern over the release of methyl tert-butyl ether (MTBE), a gasoline additive, into the aquifers used as potable water sources. MTBE readily dissolves in water and has entered the environment via gasoline spills and leaking storage tanks. In this paper, we investigate ozonation and UV-ozonation for treatment of MTBE in contaminated drinking water sources. We report the test protocol and results of using solid-phase microextraction (SPME) to determine the level of MTBE and its oxidation byproducts in samples drawn from laboratory-scale ozone and UV-ozone reactors being evaluated at a US EPA research facility. Analysis of a prepared MTBE standard indicated a detection limit on the order of 0.1 microgl(-1) with a repeatability of +/-0.4%. Results show that the overall rate of removal of MTBE via UV-ozonation in a relatively turbid surface water (15 ntu) is twice that of ozonation alone. In addition, GC-MS analysis of decomposition products showed that tert-butyl formate (TBF), methyl acetate, butene, acetone, and acetaldehyde were produced by both processes. TBF and butene reach similar maximum yields from the two processes, but are more efficiently degraded by UV-ozonation treatment. This indicates that these treatment processes also degrade these byproducts. In contrast, the remaining byproducts (methyl acetate, acetone, and acetaldehyde) are formed at similar levels during treatment, but are not degraded once formed. These byproducts may be resistant to hydrogen abstraction by hydroxyl radical.     

The distribution of particle-phase organic compounds in the atmosphere and their use for source apportionment during the Southern California Children''s Health Study

Atmospheric particulate matter (PM) samples from 12 sites in southern California, collected as part of the Southern California Children's Health Study (SCCHS), were analyzed using gas chromatography/mass spectrometry (GC/MS) techniques. Ninety-four organic compounds were quantified in these samples, including n-alkanes, fatty acids, polycyclic aromatic hydrocarbons (PAH), hopanes, steranes, aromatic diacids, aliphatic diacids, resin acids, methoxyphenols, and levoglucosan. Annual average concentrations of all detected compounds, as well as average concentrations for three seasonal periods, were determined at all 12 sites for the calendar year of 1995. These measurements provide important information about the seasonal and spatial distribution of particle-phase organic compounds in southern California. Also, co-located samples from one site were analyzed to assess precision of measurement. Excellent agreement was observed between annual average concentrations for the broad range of organic compounds measured in this study. Measured concentrations from the 12 sampling sites were used in a previously developed molecular-marker source apportionment model to quantify the primary source contributions to the PM10 organic carbon and mass concentrations at these 12 sites. Source contributions to atmospheric PM from six important air pollution sources were quantified: gasoline-powered motor vehicle exhaust, diesel vehicle exhaust, wood smoke, vegetative detritus, tire wear, and natural gas combustion. Important trends in the seasonal and spatial patterns of the impact of these six sources were observed. In addition, contributions from meat smoke were detected in selected samples.     

Methyl tert-butyl ether (MTBE) in urban and rural precipitation in Germany

The use of the oxygenate methyl tert-butyl ether (MTBE) in gasoline has led to detectable concentrations in urban and rural air up to 160 ppbV. Results from MTBE measurement in precipitation have not been reported so far. In the present study, 120 samples of precipitation collected at 17 sampling locations all over Germany have been analyzed for their MTBE content. Analysis is performed by a combination of headspace-solid-phase microextraction (HS-SPME) and gas chromatography/mass spectrometry (GC-MS). A 75 μm poly(dimethylsiloxane)/Carboxene fiber and a cryostat is used for SPME. The detection limit is 10 ng/l. In precipitation samples, MTBE was detected in wintertimes only with a maximum concentration of 85 ng/l. Measurement at Frankfurt/M City from 6 September 2000 to 12 March 2001 provided for 49% of the data concentrations in the range of 30–85 ng/l (n=17). Sampling in winter 2000/2001 at several German cities and rural locations showed that MTBE is more often detectable in urban (86%, n=78) than in rural (18%, n=42) precipitation. By comparing the results with corresponding temperatures and amounts of precipitation it can be concluded that the detection of MTBE in urban precipitation is observed at ambient temperatures lower than about 10–15°C. Moreover, the first precipitation after a dry period accumulates more MTBE than precipitation during or at the end of a wet period (wash-out effect). Highest concentrations occurred in snow samples. Corresponding mean air equilibrium concentrations of 0.04 ppbV (urban samples) and 0.01 ppbV (rural samples) are calculated. This is about one magnitude lower than year round and summertime measurements in the US and in Switzerland. Urban runoff (n=12) and corresponding precipitation sampling indicate that urban runoff might be composed of about 20% MTBE that is already transported by air and precipitation, whereas about 80% may be attributed to direct uptake of vehicle emissions and leakage near the road during precipitation.     

The Distribution of Particle-Phase Organic Compounds in the Atmosphere and Their Use for Source Apportionment during the Southern California Children’s Health Study

Abstract

Atmospheric particulate matter (PM) samples from 12 sites in southern California, collected as part of the Southern California Children’s Health Study (SCCHS), were analyzed using gas chromatography/mass spectrometry (GC/MS) techniques. Ninety-four organic compounds were quantified in these samples, including n-alkanes, fatty acids, polycyclic aromatic hydrocarbons (PAH), ho-panes, steranes, aromatic diacids, aliphatic diacids, resin acids, methoxyphenols, and levoglucosan. Annual average concentrations of all detected compounds, as well as average concentrations for three seasonal periods, were determined at all 12 sites for the calendar year of 1995. These measurements provide important information about the seasonal and spatial distribution of particle-phase organic compounds in southern California. Also, co-located samples from one site were analyzed to assess precision of measurement. Excellent agreement was observed between annual average concentrations for the broad range of organic compounds measured in this study. Measured concentrations from the 12 sampling sites were used in a previously developed molecular-marker source apportionment model to quantify the primary source contributions to the PM₁₀ organic carbon and mass concentrations at these 12 sites. Source contributions to atmospheric PM from six important air pollution sources were quantified: gasoline-powered motor vehicle exhaust, diesel vehicle exhaust, wood smoke, vegetative detritus, tire wear, and natural gas combustion. Important trends in the seasonal and spatial patterns of the impact of these six sources were observed. In addition, contributions from meat smoke were detected in selected samples.     

Detection of mutagens in unconcentrated and concentrated drinking water supplies before and after treatment using a microscale fluctuation test

The aim of this work was to study three different concentration methods coupled with the microscale fluctuation test for routine screening of different drinking water supplies before and after treatment. Unconcentrated samples were also tested. The results showed the formation of direct-acting mutagens in drinking water from surface sources after chlorination.     

The California TEAM study: Breath concentrations and personal exposures to 26 volatile compounds in air and drinking water of 188 residents of Los Angeles,Antioch, and Pittsburg,CA

The U.S. EPA carried out a study of personal exposures to 26 volatile organic chemicals in the air, drinking water, and exhaled breath of 188 California residents in 1984. Sixteen chemicals were often found above quantifiable limits in the personal air samples, but only the four trihalomethanes were often found in drinking water. The highest exposures were to 1,1,1-trichloroethane, para-dichlorobenzene, xylenes, benzene, and tetrachloroethylene. Indoor air concentrations generally exceeded outdoor air concentrations, particularly at the higher percentiles. Breath concentrations of eight chemicals showed significant correlations with preceding personal air concentrations in the two visits to Los Angeles. Smoking, employment, and automobile-related activities were identified as important sources of personal exposure to a number of target compounds.     

Exposure to methyl tertiary butyl ether and benzene in close proximity to service stations

Exposure estimates based solely on proximity to air pollution sources are not sound and require confirmation. Accordingly, since a very limited amount of actual data for this type of exposure estimate is currently available, this study was conducted to provide actual data on residents' exposure to two important gasoline constituents [methyl tertiary butyl ether (MTBE) and benzene] relative to their proximity to roadside service stations. The results confirmed that residents in neighborhoods near service stations are exposed to elevated ambient MTBE and benzene levels compared with those living farther from such a source. However, it was also found that the presumed elevated outdoor benzene levels (a mean of 1.7 ppb) even in close proximity to service stations did not exceed the indoor levels (a mean of 2.2 ppb) of exposure for those living nearby. Regardless of residents' distance from service stations, an indoor source (cigarette smoking) appeared to be the major contributor to their benzene exposure. Conversely, for MTBE, roadside service stations were found to be the major contributor to residents' exposure. In addition, the residents close to the stations were exposed to elevated indoor and outdoor MTBE levels. The sampling period (daytime and nighttime) and season (winter and summer) were additional parameters for the outdoor MTBE and benzene levels and the indoor MTBE levels. Meanwhile, the breathing zone air concentrations of service station attendants for both MTBE and benzene were significantly higher than those of drivers (p < 0.05). In addition, the breathing zone concentrations were significantly higher during summer than during winter for both drivers and attendants (p < 0.05).     

Determination of pharmaceuticals, personal care products, and pesticides in surface and treated waters: method development and survey

Water is fundamental to the existence of life since it is essential to a series of activities, such as agriculture, power generation, and public and industrial supplies. The residual water generated by these activities is released into the environment, reaches the water systems, and becomes a potential risk to nontarget organisms. This paper reports the development and validation of a quantitative method, based on solid-phase extraction and liquid chromatography tandem mass spectrometry, for the simultaneous analysis of 18 pharmaceuticals and personal care products (PPCPs) and 33 pesticides in surface and drinking waters. The accuracy of the method was determined by calculating the recoveries, which ranged from 70 to 120 % for most pesticides and PPCPs, whereas limits of quantification ranged from 0.8 to 40 ng/L. After the validation step, the method was applied to drinking and surface waters. Pesticides and PPCPs were found in concentrations lower than 135.5 ng/L. The evaluation of different water sources with regard to contamination by pesticides and PPCPs has been quite poor in southern Brazil.     

Profiles and risk assessment of phthalate acid esters (PAEs) in drinking water sources and treatment plants,East China

This study is the first report describing the occurrence of 15 phthalate acid esters (PAEs) in the three typical water sources of YiXing City, Taihu Upper-River Basin, East China. The fate of target PAEs in the Jiubin drinking water treatment plant (JTP) was also analyzed. The amounts of Σ₁₅PAE in the Hengshan (HS), Youche (YC), and Xijiu (XJ) water sources were relatively moderate, with mean values of 360, 357, and 697 ng L⁻¹, respectively. Bis(2-ethylhexyl) phthalate (DEHP) dominated the PAE concentration, making up 80% of the 15 total PAEs. The highest levels of Σ₁₅PAE were found in HS, YC, and XJ in March 2015, January 2015, and July 2014, respectively. The occurrence and concentrations of these compounds were spatially dependent, and the mean concentrations of Σ₁₅PAE in HS, YC, and XJ samples increased from the surface layer to the bottom layer with varied percentage increases. The removal efficiency of the PAEs in the finished water varied markedly, and the removal of PAEs by the JTP ranged from 12.8 to 64.5%. The potential ecosystem risk assessment indicated that the risk of PAEs was relatively low in these three water sources. However, risks posed by PAEs due to drinking water still exist; therefore, special attention should be paid to source control in the JTP, and advanced treatment processes for drinking water supplies should be implemented.

     

The occurrence of trihalomethanes in the drinking water in Greece

This paper summarizes and completes an investigation into the occurrence of trihalomethanes (THMs) in public water supplies in Greece. The investigation was conducted in three cities of Greece, Athens, Mytilene and Chalkida, from 1993 to 1998. Samples were collected from three treatment plants of Athens (Galatsi Treatment Plant--GTP, Menidi Treatment Plant--MTP, Kiourka Treatment Plant--KTP) and from the distribution systems of Athens, Mytilene and Chalkida. The sources for these systems are lakes, boreholes and wells. The concentrations of THMs ranged from 5 to 106 microg/l, from 4 to 27 microg/l and from 5 to 96 microg/l, in the distribution systems of Athens, Mytilene, Chalkida, respectively. The wide ranges of concentrations in three cities should be attributed to the organics concentration of raw water. In all the cases the THMs concentrations were higher during the summer and fall than in spring and winter. In GTP and in the distribution system receives water by GTP, from April 1993 to January 1995, Mytilene and Chalkida, brominated THMs dominated and existed at the highest concentration levels, whereas chloroform was the least prevalent compound, while in all the other cases the opposite was observed. In all samples the concentrations were lower than the maximum level of 100 microg/l for total trihalomethanes (TTHMs) set by European Community (EC).     

Role of back diffusion and biodegradation reactions in sustaining an MTBE/TBA plume in alluvial media

A methyl tert-butyl ether (MTBE) / tert-butyl alcohol (TBA) plume originating from a gasoline spill in late 1994 at Vandenberg Air Force Base (VAFB) persisted for over 15 years within 200 feet of the original spill source. The plume persisted until 2010 despite excavation of the tanks and piping within months after the spill and excavations of additional contaminated sediments from the source area in 2007 and 2008. The probable history of MTBE concentrations along the plume centerline at its source was estimated using a wide variety of available information, including published details about the original spill, excavations and monitoring by VAFB consultants, and our own research data. Two-dimensional reactive transport simulations of MTBE along the plume centerline were conducted for a 20-year period following the spill. These analyses suggest that MTBE diffused from the thin anaerobic aquifer into the adjacent anaerobic silts and transformed to TBA in both aquifer and silt layers. The model reproduces the observation that after 2004 TBA was the dominant solute, diffusing back out of the silts into the aquifer and sustaining plume concentrations much longer than would have been the case in the absence of such diffusive exchange. Simulations also suggest that aerobic degradation of MTBE or TBA at the water table in the overlying silt layer significantly affected concentrations of MTBE and TBA by limiting the chemical mass available for back diffusion to the aquifer.     

A survey of drinking water supplies in the Province of Ontario for dioxins and furans

A survey of drinking water supplies in the Province of Ontario was initiated in 1983 to determine the extent of their contamination by polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs). This drinking water survey arose from concerns regarding the discovery of PCDDs and PCDFs in sport fish from western Lake Ontario in the early 1980's.A total of 49 water supplies throughout all Regions of Ontario have been examined to date. Water supplies in the vicinity of chemical industries and pulp and paper mills were sampled more frequently; as many as 20 times. Detection limits were in the low parts per quadrillion (ppq) range for all tetra- to octachlorinated PCDDs and PCDFs.As of February 1989, 4, 347 results were received for 399 raw and treated water samples. Only 37 positive results were reported, constituting less than 1 percent of the total number of results. The O₈CDD congener accounted for 36 of the 37 positive results. The 2,3,7,8- TCDD isomer was not detected in any sample.