General plume dispersion model (GPDM) for point source emission

Gaussian-based dispersion models are widely used to estimate local pollution levels. The accuracy of such models depends on stability classification schemes as well as plume rise equations. A general plume dispersion model (GPDM) for a point source emission, based on Gaussian plume dispersion equation, was developed. The program complex was developed using Java and Visual basic tools. It has the flexibility of using five kinds of stability classification schemes, i.e., Lapse Rate, Pasquill–Gifford (PG), Turner, σ–θ and Richardson number. It also has the option of using two types of plume rise formulations – Briggs and Holland’s. The model, applicable for both rural and urban roughness conditions, uses meteorological and emission data as its input parameters, and calculates concentrations of pollutant at the center of each cell in a predefined grid area with respect to the given source location. Its performance was tested by comparing with 4-h average field data of continuous releases of SO₂ from Dadri thermal power plant (Uttar Pradesh, India). Results showed that the Turner scheme used with Holland’s equation gives the best outcome having a degree of agreement (d) of 0.522.     

基于颗粒物光量子雷达的颗粒物排放实时溯源及应用

在大气污染治理中,传统探测方式在局地大气颗粒物排放源的精准定位和实时溯源方面还有所不足。自主研发的1 550 nm波长颗粒物光量子雷达,具备探测效率高、人眼安全等特点,360°水平扫描一周仅需8.5 min。基于该雷达水平扫描监测,结合迭代拼接法和新发展的颗粒物示踪系数及污染源定位方法,可准确识别并定位出当地的污染排放源位置。对于部分污染排放定位溯源案例,结合多图展现并分析了颗粒物排放、扩散、传输、消散过程中的烟羽变化,并结合卫星图像确认了相应工业生产和建筑扬尘等典型颗粒物排放源。地面监测数据分析了部分污染源对监测站点颗粒物浓度的影响。该雷达通过低仰角、可重复性的快速扫描,结合符合颗粒物扩散规律的分析过程,在颗粒物污染实时溯源定位方面展现了极高的准确性。     

A model for the maximum credible hourly impact on any ground receptor from point sources with momentumdominated plume rise

A pollutant dispersion model is developed, allowing rapid evaluation of the maximum credible one-hour-average concentration on any given ground-level receptor, along with the corresponding critical meteorological conditions (wind speed and stability class) for stacks with momentum-dominated plume rise in urban or rural areas under buoyancy or no buoyancy induced dispersion. Site-specific meteorological data are not required, as the computed concentrations are maximized against all credible combinations of wind speed, stability class, and mixing height.The analysis is based on the dispersion relations of Pasquill-Gifford and Briggs for rural and urban settings respectively, the buoyancy induced dispersion correlation of Pasquill, the wind profile exponent values suggested by Irwin, the momentum plume rise relations of Briggs, as well as the Benkley and Schulman's model for the minimum mixing heights.The model is particularly suited for air pollution management studies, as it allows fast screening of the maximum impact on any selected receptor and evaluation of the ways to have this impact reduced. Also, for regulatory purposes, as it allows accurate setting of minimum stack height requirements as function of the exit gas volume and velocity, the pollutant emission rates and their hourly concentration standards, as well as the source location relative to sensitive receptors.     

Impacts of ocean CO2 disposal on marine life: I. A toxicological assessment integrating constant‐concentration laboratory assay data with variable‐concentration field exposure

Feasibility studies suggest that the concept of capturing CO₂ from fossil fuel power plants and discharging it to the deep ocean could help reduce atmospheric CO₂ concentrations. However, the local reduction in seawater pH near the point of injection is a potential environmental impact. Data from the literature reporting on toxicity of reduced pH to marine organisms potentially affected by such a plume were combined into a model expressing mortality as a function of pH and exposure time. Since organisms exposed to real plumes would experience a time‐varying pH, methods to account for a variable exposure were reviewed and a new method developed based on the concept of isomortality. In part II of this paper, the method is combined with a random‐walk model describing the transport of passive organisms through a low pH plume leading to a Monte‐Carlo‐like risk assessment which is applied to several candidate CO₂ injection scenarios.     

基于3S技术的桂林市南溪河污染现状调查

城区小流域常是水污染较重的区域,又是污染源密集的地方,其非点源污染的监测与评估,需要实用方法。本调查基于3S技术,开展流域的监测与评价,包括空间定位的精度控制、非点源的遥感分类解译、采用排污系数对非点源污染评估、对污染源及污水管网做GIS空间分析。结合水质监测进行污径比和水环境容量的评价。重点讨论了城区人口解译方法和污染源评估方法,探讨典型城区非点源污染监测的思路。     

浙江省环保重点城市SO 2 排放的控制模式

通过分析城市SO2 地面浓度来源 ,运用高、中、低架源对地面污染物浓度贡献的理论及高斯烟羽模式推出SO2空气质量管理模式 ,确定了城市SO2 地面环境质量的控制目标。     

Monitoring fugitive dust emissions from off-highway vehicles traveling on unpaved roads and trails using passive samplers

Vehicles traveling on dry, unpaved roads generate copious quantities fugitive dust that contributes to soil erosion, and potentially threatens human health and ecosystems. The purpose of this study was to develop a low-cost technique for monitoring road dust that would enable land managers to estimate soil loss. The "sticky-trap" collectors developed were evaluated at the Turkey Bay off-highway vehicle (OHV) riding area on the Land Between the Lakes National Recreation Area, in western Kentucky. The results showed that the dust plume created by vehicle traffic was heterogeneous: larger particles were in the lower part of the plume and deposited closer to the source, smaller particles were carried higher in the plume and traveled at least 100 m away from the source. Collection of particles parallel to the source was also heterogeneous, suggesting that measurements taken at a single point may not be appropriate for estimating erosion losses. Measurements taken along two trails indicate that when large numbers of riders are present, dust concentrations may reach unhealthful conditions for riders, but that it is unlikely that fugitive dust is harming native vegetation, given frequent rainfall. The study demonstrated that OHV traffic contributes to substantial erosion of roadbeds because of aeolian transport.     

Multipoint source method in air pollution modelling of cold start emission

The paper presents a new method of air pollution modelling on a micro scale. For estimation of concentration of car exhaust pollutants, each car is treated as an instantaneous moving emission source. This approach enables us to model time and spatial changes of emission, especially during cold and cool start of an engine. These stages of engine work are a source of significant pollution concentration in urban areas. In this work, two models are proposed: one for the estimation of emission after cold start of the engine and another for the prediction of pollutant concentration. The first model (defined for individual exhaust gas pollutants) enables us to calculate the emission as a function of time after the cold or cool start, ambient temperature and average speed of motion. This model uses the HBEFA database. The second mathematical model is developed in order to calculate the pollutant dispersion and concentrations. The finite volume method is applied to discretise the set of partial differential equations describing wind flow and pollutant dispersion in the domain considered. Models presented in this paper can be called short-term models on a small spatial scale. The results of numerical simulation of pollutant emission and dispersion are also presented.     

Numerical modelling of the environmental impact of landfill leachate leakage on groundwater quality – a field application

Waste disposal facilities are mainly responsible for the gradual quality degradation of subsurface freshwater reservoirs. The main objective of this work is to identify the groundwater contamination risk due to potential leachate leakage and seepage beneath the municipal landfill of the City of Patras in Greece. A groundwater and leachate mass transport model of the underlying aquifer was developed for this purpose. The derived simulation results indicate that, depending on the permeability of the soil at the location of leakage, the contamination risk for the groundwater can be high. In order to quantify the magnitude and the extent of the leakage, a risk assessment model for the leachate contaminant plume was developed. The risk assessment analysis shows that the municipal drinking wells are under high risk of contamination.     

基于SHERPA的环境空气质量减排情景模拟评估

分析了SHERPA综合评价模型的基本原理和主要建模理念,重点介绍了其在环境空气质量减排情景模拟评估方面的作用,以及在排放源与受体关系(SRR)方面的处理方法,比较了其与欧盟常用的其他情景模拟模型的优缺点。SHERPA模型的特点是空间灵活性较好,对于任何给定地点,可以快速评估不同地区对该研究地点空气质量的影响。SHERPA模型的3个主要功能为污染物来源分析、决策支持和情景模拟。基于SHERPA模型对法国环境空气中PM_(2.5)、PM_(10)和NO_2年均浓度进行污染来源分析、决策支持分析和减排情景模拟评估,展示了模型在环境治理措施优先级筛选和政府间联合治理措施协调建议方面的功能和作用,以期为中国环境空气质量预测预报、环境质量管理措施的制定和成效评估等环境服务与管理工作提供借鉴。     

Mathematical Modeling and Numerical Algorithms for Simulation of Oil Pollution

This paper deals with the mathematical modeling and algorithms for the problem of oil pollution. For solving this task, we derive the adjoint problem for the advection–diffusion equation describing the propagation of oil slick after an accident, which we call the main problem. We prove a fundamental equality between the solutions of the main and the adjoint problems. Based on this equality, we propose a novel method for the identification of the pollution source location and the accident time of oil emission. This approach is illustrated on an example for an accident in the offshore of the central part of the Vietnamese coast. Numerical simulations demonstrate the effectiveness of the proposed method. Besides, the method is verified for 1D model of substance propagation.     

Validation of Urban Emission Inventories

Two emission validation methods are presented. The first method focuses on the precision of the emission factors and the accuracy of modelled traffic flows. Emission factors derived from the COPERT II methodology are compared with on-board emission measurements and modelled traffic flow rates are compared with observations. The second validation method focuses on the completeness of the inventory, i.e. coverage of all sources. The method compares measured pollutant fluxes in the urban plume with the downwind transported and dispersed emissions integrated over plume width and mixing height. Both methods seem to indicate that traffic emission factors used in the urban emission inventories show large uncertainties. Besides the lack of measurement precision this is mainly induced by external influence factors like driving behaviour and vehicle maintenance.     

Locating pollutant emission sources with optical remote sensing measurements and an improved one-dimensional radial plume mapping technique

Previous studies have shown that there was a relatively large amount of uncertainty along the major wind direction in the results of locating emission sources using the one-dimensional radial plume mapping (RPM(1D)) technique based on optical remote sensing measurements. This paper proposes setting up an additional monitoring line that is perpendicular to the original scanning beam geometry to reduce this uncertainty. We first conducted a computer simulation study using the Gaussian dispersion model to generate the downwind concentrations of plumes from 400 source locations in a 201 m × 201 m spatial domain under various wind directions (n = 181). The optical remote sensing instrument was assumed to be at (0, 0) with two perpendicular monitoring lines, each of which had three beam segments of equal length. Each pair of the reconstructed downwind concentration profiles was then used to trace back to the source locations. The results showed that the accuracy of the method and its uncertainty were improved by using the proposed two-line RPM(1D) approach rather than the original one-line RPM(1D) approach at most simulated source locations. In a follow-up field experiment, a tracer gas was released at the coordinate of (100, 100). The release location was covered within the 0.25- to 0.5-probability area of the estimated results, and the distance between the actual and estimated source locations was 18.4 m (9.2% of the longest beam path).     

Methane emission from naturally ventilated livestock buildings can be determined from gas concentration measurements

Determination of emission of contaminant gases as ammonia, methane, or laughing gas from natural ventilated livestock buildings with large opening is a challenge due to the large variations in gas concentration and air velocity in the openings. The close relation between calculated animal heat production and the carbon dioxide production from the animals have in several cases been utilized for estimation of the ventilation air exchange rate for the estimation of ammonia and greenhouse gas emissions. Using this method, the problem of the complicated air velocity and concentration distribution in the openings is avoided; however, there are still some important issues remained unanswered: (1) the precision of the estimations, (2) the requirement for the length of measuring periods, and (3) the required measuring point number and location. The purpose of this work was to investigate how estimated average gas emission and the precision of the estimation are influenced by different calculation procedures, measuring period length, measure point locations, measure point numbers, and criteria for excluding measuring data. The analyses were based on existing data from a 6-day measuring period in a naturally ventilated, 150 milking cow building. The results showed that the methane emission can be determined with much higher precision than ammonia or laughing gas emissions, and, for methane, relatively precise estimations can be based on measure periods as short as 3 h. This result makes it feasible to investigate the influence of feed composition on methane emission in a relative large number of operating cattle buildings and consequently it can support a development towards reduced greenhouse gas emission from cattle production.     

Near Field Dispersion in the Urban Environment - A Hydraulic Flume Study

The dispersion of material released from a point source immediately upwind of an obstacle array has been examined in a hydraulic flume with a low level of background turbulence. The main purpose of the experiments was to examine the interaction of the plume and the internal boundary layer (IBL) created over the obstacle array. The obstacle array consisted of 11 rows of cubes at 16% packing density in a staggered arrangement. Plume dispersion was measured using flow visualization with Rhodamine dye and also with a thermal tracer technique. During the experiments the source release height was varied between z = 0 and z = 4H, where H is the obstacle height. For the low-level releases, the upper boundary of the plume followed the growth of the IBL over the array. For higher level releases (z/H 2) the rate of plume growth was much reduced until the point downstream where it descended into the IBL, after which it experienced the intense turbulent mixing within the array. This suggests that the urban lateral spread parameter _y should be a strong function of height in situations where the turbulence level in the ambient approach flow is low. These results highlight the importance of the ambient turbulence even in strongly obstacle-affected dispersion.     

Source Release-Rate Estimation of Atmospheric Pollution from a Non-Steady Point Source at a Known Location

The goal is to build up an inverse model capable of finding the release history of atmospheric pollution by using measured gas concentration data at just one location on the ground and identify the factors which affects the accuracy of the model predictions. The problem involves a non-steady point source of pollution at a known location in the atmosphere. This problem of finding the release rate is an ill-posed inverse problem and its solution is extremely sensitive to errors in the measurement data. Special regularisation methods, which stabilise the process of the solution, must be used to solve the problem. The method described in this paper is based on linear least-squares regression and Tikhonov regularisation, coupled with the solution of an advection-diffusion equation for a non-steady point source. The accuracy of the method is examined by imposing normally-distributed relative noise into the concentration data generated by the forward model as well as some real experimental data.     

Effect of Setback Distance on Ability of Gravel Trenches to Intercept Contaminated Groundwater

Computer simulations tested the ability of gravel interceptor trenches to capture a plume of contaminated groundwater. The plume had a maximum length and width of 87 and 19 m, respectively. In alternate simulations, one-meter wide trenches were located 5, 10, 20, and 50 m downgradient of the plume. A minimum trench length and time required to capture the plume was determined for each location (setback). The plume was considered captured if it passed entirely through a trench. A 21 m-long trench captured the plume at setbacks of 5 and 10 m. Minimum trench length increased to 23 and 25 m at setbacks of 20 and 50 m, respectively. Increased contaminant spreading with distance traveled dictated longer trenches at larger setbacks. Results of this study suggest that, at settings where contaminant plumes are carefully monitored and spatially defined, passive interceptor trenches should be close to a plumes leading tip and slightly longer than the maximum width of the plume.     

基于激光雷达技术的粉尘污染源监测

针对粉尘污染点源数量多、夜间偷排偷放监测难等问题,环保监测迫切需要发展新一代遥感监测技术,为环境保护提供技术支撑。激光雷达具有远距离、全天时监测的优势,可实现对污染源的客观、全天时监测。为了验证激光雷达主动遥感技术监测粉尘污染源排放的可行性,在河北省组织了一次粉尘污染源的Lidar监测实验,在进行距离校正的基础上,发展了Lidar点源污染监测指数因子方法。结果表明:烟尘排放浓度与Lidar指数因子具有较好的一致性,校正决定系数可达0.94。在稳定排污的情况下研究Lidar指数因子的限值,结果显示,将指数因子的限值设为2.3时,与在线监测的一致性可以达到99%以上。     

Groundwater monitoring plans at small-scale sites--an innovative spatial and temporal methodology

An innovative methodology for improving existing groundwater monitoring plans at small-scale sites is presented. The methodology consists of three stand-alone methods: a spatial redundancy reduction method, a well-siting method for adding new sampling locations, and a sampling frequency determination method. The spatial redundancy reduction method eliminates redundant wells through an optimization process that minimizes the errors in plume delineation and the average plume concentration estimation. The well-siting method locates possible new sampling points for an inadequately delineated plume via regression analysis of plume centerline concentrations and estimation of plume dispersivity values. The sampling frequency determination method recommends the future frequency of sampling for each sampling location based on the direction, magnitude, and uncertainty of the concentration trend derived from representative historical concentration data. Although the methodology is designed for small-scale sites, it can be easily adopted for large-scale site applications. The proposed methodology is applied to a small petroleum hydrocarbon-contaminated site with a network of 12 monitoring wells to demonstrate its effectiveness and validity.     

氟化物应作为建陶行业环境影响评价的因子

对建陶行业氟化物的来源及其在环境中的化学行为进行了分析,结果表明,在釉面砖生产过程中排放的氟化物浓度超过国家规定的标准。并以此提出总量控制和评价因子的问题,探讨了氟污染排放标准和质量标准的相关性。