Organic contaminants in canadian municipal sludges

A comparison of several extraction methodologies for the analysis of base-neutral and acid organic contaminants (EPA priority pollutants) in municipal sludge was conducted. Sludge was spiked with selected contaminants and extracted wet and following air-drying by a variety of techniques such as dilution, centrifuge extraction, Soxhlet extraction and high speed mixing (Polytron^R, Waring^R and ultrasonic probe). All of the techniques produced variable rdsults. Recoveries of spiked compounds ranged from 0 to > 100% and, in general, the relative standard deviations ranged from 20 to 50%. Extraction of wet sludge using high speed mixing was considered to be the most satisfactory technique. Based on analyses of 15 municipal sludges derived mainly from industrial centres, it is suggested that agricultural utilization of Canadian sludges probably does not represent a significant organic contaminant hazard to the food chain. Organic contaminant concentrations in the sludges generally were < 10 mg kg⁻¹ dw. Phthalate esters in several sludges and polynuclear aromatic hydrocarbons (PAHs) in Hamilton sludge exceeded 10 mg kg⁻¹ dw; however, phthalate esters are readily degraded in soil and the Hamilton sludge is incinerated. “Acceptable” organic contaminant concentrations in sludges for use on pasture and arable lands are suggested. However, it is recommended that further analytical research be undertaken to develop more accurate and precise methods for measuring organic contaminants in municipal sludge and that an expanded program of sampling and analysis be undertaken to provide more reliable information concerning organic contaminant concentrations in Canadian sludges.     

Fractionation of heavy metals in sludge from anaerobic wastewater stabilization ponds in southern Spain

The analysis of heavy metals is a very important task to assess the potential environmental and health risk associated with the sludge coming from wastewater treatment plants (WWTPs). However, it is necessary to apply sequential extraction techniques to obtain suitable information about their bioavailability or toxicity. In this paper, a sequential extraction scheme according to the Standard, Measurements and Testing Programme of the European Commission was applied to sludge samples collected from ten anaerobic wastewater stabilization ponds (WSPs) located in southern Spain. Al, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Ti and Zn were determined in the sludge extracts by inductively coupled plasma atomic emission spectrometry. In relation to current international legislation for the use of sludge for agricultural purposes, none of the metal concentrations exceeded maximum permitted levels. Overall, heavy metals were mainly associated with the two less-available fractions (34% oxidizable metal and 55% residual metal). Only Mn and Zn showed the highest share of the available (exchangeable and reducible) fractions (25-48%).     

Accumulation and fate of selected heavy metals in a biological wastewater treatment system

The aim of this research was to study the accumulation and removal of heavy metals (Cd, Cu, Pb, Zn) by a biological wastewater treatment system. Heavy metal contents in the influent and effluent wastewater were compared. Also, the heavy metal contents in the sludge before and after anaerobic digestion were compared. The results showed: (1) more pronounced variations in the contents of Cu and Zn than that of Cd and Pb, which showed that at 0.02 for Cd and 0.05 mg/l for Pb, the reduction in their contents was insignificant; (2) that removal of heavy metals was directly proportional to their initial contents in the influent wastewater. Corresponding to the influent contents, in increasing order, the reduction in heavy metal contents was: Cd相似文献   

Assessment of benefits and risks of landfill materials for agriculture in Eritrea

In Eritrea, farmers have applied landfill materials as fertiliser to their fields for several decades. A sampling scheme in the landfill site of Asmara and selected farmers' fields was carried out to investigate the benefits and risks of using landfill materials for agriculture. Soil samples were collected from farmers' fields (7 samples) and from the Asmara landfill site (12 samples). The samples were analysed for major plant nutrients, heavy metals (Cd, Cr, Cu, Pb, Ni, Hg and Zn), and some physical properties. Nearly 65% (by weight) of the total landfill material mined from the landfill site constituted waste fractions of various substances. The remaining 35% was composed of soil-like materials, which are apparently used to fertilize agricultural soils. The average organic matter, total nitrogen, and available phosphorus contents of soils with landfill material measured 2.4%, 0.13%, and 45 mg kg(-1), respectively. However, soils without landfill material consisted of 1.1 % organic matter, 0.04% total N, and <40 mg kg(-1) of available P. Except for Hg, all the other heavy metals in the landfill site showed values above the permissible limits. In particular, the average concentrations of Cu (913 mg kg(-1)) and Pb (598 mg kg(-1)) in the landfill site were nine-fold and four-fold greater than the allowable limits, respectively. It is, therefore, suggested that composting fresh organic wastes should be considered and tested as an alternative material for fertilising agricultural soils and to maintain the quality of the environment.     

Leaching characteristics and phytotoxic effects of sewage sludge biochar

Biochar was prepared via the pyrolysis of sewage sludge at temperatures ranging from 300 to 900 °C and the physical–chemical compositions of the biochars obtained were analyzed. Leaching tests were conducted using the biochars to investigate the release of the constituents and their phytotoxic effects on wheat (Triticum aestivum) seeds in a germination test. Multivariate analyses were used to evaluate the contributions of the constituents to the germination index (GI). The results showed that the biochars were rich in micronutrient contents and they improved the germination of wheat. The heavy metal contents were higher in the biochars than the sewage sludge and their levels increased with the pyrolysis temperature, but they were within the acceptable limits for land application, thereby suggesting that sewage sludge is suitable for use as a biochar substrate. The different components of the biochar leachates could promote and inhibit the germination of wheat seeds, where the GI was promoted at lower concentrations but inhibited at higher concentrations. Our results suggest that biochar is an effective and environmentally friendly fixative for the immobilization of heavy metals in sewage sludge when applied to land or disposed of in landfill, but its ecotoxicity needs to be assessed to ensure its environmental safety.     

Chemical and microbiological hazards associated with recycling of anaerobic digested residue intended for agricultural use

In the present study, three full-scale biogas plants (BGP) were investigated for the concentration of heavy metals, organic pollutants, pesticides and the pathogenic bacteria Bacillus cereus and Escherichia coli in the anaerobically digested residues (ADR). The BGPs mainly utilize source-separated organic wastes and industrial food waste as energy sources and separate the ADR into an ADR-liquid and an ADR-solid fraction by centrifugation at the BGP. According to the Norwegian standard for organic fertilizers, the ADR were classified as quality 1 mainly because of high zinc (132-422 mg kg(-1) DM) and copper (23-93 mg kg(-1) DM) concentrations, but also because of high cadmium (0.21-0.60 mg kg(-1) DM) concentrations in the liquid-ADR. In the screening of organic pollutants, only DEHP (9.7-62.1 mg kg(-1)) and ∑ PAH 16 (0.2-1.98 mg kg(-1) DM) were detected in high concentrations according to international regulations. Of the 250 pesticides analyzed, 11 were detected, but only imazalil (<0.30-5.77 mg kg(-1) DM) and thiabendazol (<0.14-0.73 mg kg(-1) DM) were frequently detected in the ADR-fiber. Concentrations of imazalil and thiabendazol were highest during the winter months, due to a high consumption of citrus fruits in Norway in this period. Ten percent of the ADR-liquid samples contained cereulide-producing B. cereus, whereas no verotoxigenic E. coli was detected. The authors conclude that the risk of chemical and bacterial contamination of the food chain or the environment from agricultural use of ADR seems low.     

Agrochemical characterisation of the solid by-products and residues from the winery and distillery industry

The winery and distillery industry produces a great quantity of residues, whose management and disposal are environmental problems due to their seasonal character and some polluting characteristics. The main solid by-products and residues generated are grape stalk, grape pomace or marc, wine lee, exhausted grape marc and winery sludge. In this study, 87 samples of winery and distillery residues were collected from different Spanish wineries and distilleries. Electrical conductivity, pH, total organic matter, organic carbon, polyphenols and contents of plant nutrients and heavy metals were determined. The purpose of this research was to study the composition of these wastes and to find relationships in order to use easily analysable parameters to estimate their composition. In general, the winery and distillery residues showed low pH (mean values ranged from 3.8 to 6.8) and electrical conductivity values (1.62-6.15 dS m(-1)) and high organic matter (669-920 g kg(-1)) and macronutrient contents, especially in K (11.9-72.8 g kg(-1)). However, a notable polyphenol concentration (1.2-19.0 g kg(-1)) and low micronutrient and heavy metal contents were also observed, some of these properties being incompatible with agricultural requirements. Therefore, conditioning treatments are necessary prior to possible use of these wastes. In all wastes, significant correlations were found between easily determined parameters, such as pH, electrical conductivity and total organic matter, and most of the parameters studied. The regression models obtained are also discussed.     

Threshold amounts of organic carbon needed to initiate reductive dechlorination in groundwater systems

Aquifer sediment and groundwater chemistry data from 15 Department of Defense facilities located throughout the United States were collected and analyzed with the goal of estimating the amount of natural organic carbon needed to initiate reductive dechlorination in groundwater systems. Aquifer sediments were analyzed for hydroxylamine and NaOH‐extractable organic carbon, yielding a probable underestimate of potentially bioavailable organic carbon (PBOC). Aquifer sediments were also analyzed for total organic carbon (TOC) using an elemental combustion analyzer, yielding a probable overestimate of bioavailable carbon. Concentrations of PBOC correlated linearly with TOC with a slope near one. However, concentrations of PBOC were consistently five to ten times lower than TOC. When mean concentrations of dissolved oxygen observed at each site were plotted versus PBOC, it showed that anoxic conditions were initiated at approximately 200 mg/kg of PBOC. Similarly, the accumulation of reductive dechlorination daughter products relative to parent compounds increased at a PBOC concentration of approximately 200 mg/kg. Concentrations of total hydrolysable amino acids (THAA) in sediments also increased at approximately 200 mg/kg, and bioassays showed that sediment CO₂ production correlated positively with THAA. The results of this study provide an estimate for threshold amounts of bioavailable carbon present in aquifer sediments (approximately 200 mg/kg of PBOC; approximately 1,000 to 2,000 mg/kg of TOC) needed to support reductive dechlorination in groundwater systems. © 2012 Wiley Periodicals, Inc.     

Extracting humic acids from digested sludge by alkaline treatment and ultrafiltration

The concentration of hardly biodegradable humic substances in sludge would relatively increase after anaerobic digestion due to the degradation of other organic substances. Thus, extracting humic substances from digested sludge as a liquid organic fertilizer was tested using alkaline treatment and ultrafiltration, and the dewaterability of the residual sludge was also tested. The results showed that the contents of humic acids and fulvic acids in digested sludge were 16.4 mg/g total solids and 88.9 mg/g total solids, respectively, and most of the humic acids had a molecular weight higher than 50 kDa. Hence, the membrane with a molecular weight cut-off of 50 kDa was used for humic acids recovery from the centrifugation supernatant after alkaline sludge disintegration with an optimum NaOH dose of 0.1 mol/L. Under these conditions, the total concentration of humic acids and fulvic acids was 4239 mg/L in the retention solution, which can be further concentrated and processed for liquid fertilizer. The total recovery rate of sludge humic acids and fulvic acids was about 25 %. The dewatering performance of the residual sludge was better than that of the untreated sludge when the residual sludge was diluted to a water content of 95–98 % and then conditioned with polyacrylamide at a dose of 10–30 mg/L.     

Composition of a Spanish sewage sludge and effects on treated soil and olive trees

The effects of sewage sludge (SL) application on the soil and olive trees (Olea europaea L., cultivar: cornicabra) were studied. The plants were grown in 8.5L pots and subjected to the following treatments: 0, 3.66, 7.32, 14.65, 29.3, 58.6, and 117.2 g SL kg(-1) soil that corresponded, respectively, to 0, 4, 8, 16, 32, 64 and 128 M g ha(-1) dry weight of sewage sludge. The application of SL at the rates 64 and 128 M g ha(-1) produced leaf tip burning and leaf drop after 120 days, although cumulative metal pollutant loading rates was below USEPA and European regulations. This toxicity symptom could be caused by the high sodium levels in the leaves (over 0.19%), which can damage olive tree development. The Na contents of leaves were well correlated with soil Na content (r2: 0.91). In general, SL rates significantly increased the level of Cr, Ni, Cu, Zn, Cd and Pb in soil and plants, but these concentrations were in the normal ranges, except for the Zn concentration, which was over the critical soil content for the rates of 32, 64, 128 Mg ha(-1) but not in the leaves. Results suggested that regulations about the utilization of sewage sludge on agricultural land should consider the limit values for salt, and not only metals, that may be added to soil, in order to minimize the risk of negative effects to plant health.     

On the Impact of Land Application of Secondary Sludge

Sewage sludge from the extended aeration municipal wastewater treatment plant of Kalamata (Greece), dewatered and dried was tested for potential land application. Experiments were carried out simulating rainfall, one low-rate high-duration at 20 mm/d, and one high-rate low-duration at 6.6 mm/d. Leachate was collected and analyzed as a function of accumulated rainfall. The sludge was found suitable for agricultural uses on the basis of the relevant EEC Directive. Leachates contained P and heavy metals well above the allowable limits for discharge, implying that transport through the soil can be decisive on the likelihood of groundwater contamination. High-rate low-duration rain events give higher contaminant concentrations in the accumulated leachates.     

Treatment of tar pond sludge in a circulating fluidized bed combustor

A series of tests to burn mixtures of tar pond sludge and coal was carried out using a mini‐circulating fluidized bed combustor (mini‐CFBC). During the tests, carbon dioxide, oxygen, carbon monoxide, sulfur dioxide, and nitrogen oxides in the flue gas were monitored continuously. Stack gas sampling was carried out for hydrochloric acid, metals, particulate matter, volatile organic compounds (VOCs), total hydrocarbons, semivolatile organic compounds (SVOCs), dioxins and furans (PCDD/Fs), and polychlorinated biphenyls (PCBs). Results showed that hydrochloric acid, mercury, particulate matter, PCDD/F, and metal concentrations were all below both the current limits and the gas‐release limits to be implemented in 2008 in Canada. The new 2008 emissions limits will reduce the maximum allowable concentrations of most pollutants by half. Thus, the maximum concentration for particulate matter will be 5 mg/m³ (from the current maximum concentration of 10 mg/m³);the maximum concentration for hydrochloric acid will be 5 mg/m³ (from 10 mg/m³); and the‐maximum concentration for dioxins and furans will be 0.032 ng/m toxic equivalent (from 0.08 ng/mcurrently). Sulfur capture efficiency was 89–91 percent. The percentage of fuel nitrogen converted to nitrogen oxides was of the order of 4.7 to 6.1, which is significantly lower than that of conventional pulverized coal‐fired boilers and well within the normal range for fluidized bed combustors (FBCs). PCB and polycyclic aromatic hydrocarbon (PAH) emissions levels were comparable or lower than levels reported in the literature for industrial‐scale FBCs. VOC concentrations were low except for benzene, for which the concentration was higher than that reported for pulverized coal‐fired utility boilers. In addition, carbon monoxide concentration was high at 1,200 to 2,200 parts per million. However, these carbon monoxide concentrations are typical of the mini‐CFBC firing coal. The trials showed that for 10 percent by weight tar pond sludge mixed with 90 percent by weight coal, the combustion was both stable and efficient. The tests demonstrated that CFBC technology is an environmentally sound option for eliminating tar pond waste sludge. © 2005 Wiley Periodicals, Inc.     

Waste paper and clinoptilolite as a bulking material with dewatered anaerobically stabilized primary sewage sludge (DASPSS) for compost production

Environmental problems associated with sewage sludge disposal have prompted strict legislative actions over the past few years. At the same time, the upgrading and expansion of wastewater treatment plants have greatly increased the volume of sludge generated. The major limitation of land application of sewage sludge compost is the potential for high heavy metal content in relation to the metal content of the original sludge. Composting of sewage sludge with natural zeolite (clinoptilolite) can enhance its quality and suitability for agricultural use. However, the dewatered anaerobically stabilized primary sewage sludge (DASPSS) contained a low concentration of humic substances (almost 2%), and the addition of the waste paper was necessary in order to produce a good soil conditioner with high concentrations of humics. The final results showed that the compost produced from DASPSS and 40-50% w/w of waste paper was a good soil fertilizer. Finally, in order to estimate the metal leachability of the final compost product, the generalized acid neutralization Capacity (GANC) procedure was used, and it was found that by increasing the leachate pH, the heavy metal concentration decreased. The application of the sequential chemical extraction indicated that metals were bound to the residual fraction characterized as a stabilize fractions.     

Scientific basis of dissolved organic carbon limitation for landfilling of municipal treatment sludge – Is it attainable and justifiable?

This study evaluated the scientific and technical basis of the dissolved organic carbon (DOC) limitation imposed on municipal sludge for landfilling, mainly for assessing the attainability of the implemented numerical level. For this purpose, related conceptual framework was analyzed, covering related sewage characteristics, soluble microbial products generation, and substrate solubilization and leakage due to hydrolysis. Soluble COD footprint was experimentally established for a selected treatment plant, including all the key steps in the sequence of wastewater treatment and sludge handling. Observed results were compared with reported DOCs in other treatment configurations. None of the leakage tests performed or considered in the study could even come close to the prescribed limitation. All observed results reflected 10–20 fold higher DOC levels than the numerical limit of 800 mg/kg (80 mg/L), providing conclusive evidence that the DOC limitation imposed on municipal treatment sludge for landfilling is not attainable, and therefore not justifiable on the basis of currently available technology.     

Comparative study of the methods used for treatment and final disposal of sewage sludge in European countries

Municipal wastewater treatment results to the production of large quantities of sewage sludge, which requires proper and environmentally accepted management before final disposal. In European Union, sludge management remains an open and challenging issue for the Member States as the relative European legislation is fragmentary and quite old, while the published data concerning sludge treatment and disposal in different European countries are often incomplete and inhomogeneous. The main objective of the current study was to outline the current situation and discuss future perspectives for sludge treatment and disposal in EU countries. According to the results, specific sludge production is differentiated significantly between European countries, ranging from 0.1 kg per population equivalent (p.e.) and year (Malta) to 30.8 kg per p.e. and year (Austria). More stringent legislations comparing to European Directive 86/278/EC have been adopted for sludge disposal in soil by several European countries, setting lower limit values for heavy metals as well as limit values for pathogens and organic micropollutants. A great variety of sludge treatment technologies are used in EU countries, while differences are observed between Member States. Anaerobic and aerobic digestion seems to be the most popular stabilization methods, applying in 24 and 20 countries, respectively. Mechanical sludge dewatering is preferred comparing to the use of drying beds, while thermal drying is mainly applied in EU-15 countries (old Member States) and especially in Germany, Italy, France and UK. Regarding sludge final disposal, sludge reuse (including direct agricultural application and composting) seems to be the predominant choice for sludge management in EU-15 (53% of produced sludge), following by incineration (21% of produced sludge). On the other hand, the most common disposal method in EU-12 countries (new Member States that joined EU after 2004) is still landfilling. Due to the obligations set by Directive 91/271/EC, a temporary increase of sludge amounts that are disposed in landfills is expected during the following years in EU-12 countries. Beside the above, sludge reuse in land and sludge incineration seem to be the main practices further adopted in EU-27 (all Member States) up to 2020. The reinforcement of these disposal practices will probably result to adoption of advanced sludge treatment technologies in order to achieve higher pathogens removal, odors control and removal of toxic compounds and ensure human health and environmental protection.     

Behaviour of Cd,Cr, Mn,Ni, Pb,and Zn in sewage sludge incineration by fluidised bed furnace

Cd, Cr, Mn, Ni, Pb, and Zn behaviour during sewage sludge incineration was investigated in seven pilot tests using a circulating fluidised bed furnace. Dewatered sludge at a solids concentration of 15-18% was fed to the furnace either alone (two tests) or spiked with chlorinated organic compounds (five tests). The behaviour of metals in the fluidised bed furnace was studied by comparing metal concentrations in the two main ash streams: ash separated from the cyclone immediately following the fluidised bed furnace, and fly ash recovered in the final bag filter. A metal enrichment factor was defined as the ratio of metal concentration between filter ash and cyclone ash. Only Cd and Pb showed any significant enrichment. Their enrichment factors were mainly affected by chlorine concentration in the feed sludge. To check whether simple equilibrium models may explain and predict metal behaviour, experimental data were compared with percentage of the metal vaporisation in the combustion chamber predicted using a thermodynamic model. Discrepancies between model predictions and experimental results are accounted for by considering that kinetics may be a limiting factor in the formation of metal chloride gaseous species. Due to the very short sludge residence time in the fluidised bed furnace, the gaseous compounds have little chance to evolve completely.     

Priority and emerging pollutants in sewage sludge and fate during sludge treatment

This paper aims at characterizing the quality of different treated sludges from Paris conurbation in terms of micropollutants and assessing their fate during different sludge treatment processes (STP). To achieve this, a large panel of priority and emerging pollutants (n = 117) have been monitored in different STPs from Parisian wastewater treatment plants including anaerobic digestion, thermal drying, centrifugation and a sludge cake production unit. Considering the quality of treated sludges, comparable micropollutant patterns are found for the different sludges investigated (in mg/kg DM – dry matter). 35 compounds were detected in treated sludges. Some compounds (metals, organotins, alkylphenols, DEHP) are found in every kinds of sludge while pesticides or VOCs are never detected. Sludge cake is the most contaminated sludge, resulting from concentration phenomenon during different treatments. As regards treatments, both centrifugation and thermal drying have broadly no important impact on sludge contamination for metals and organic compounds, even if a slight removal seems to be possible with thermal drying for several compounds by abiotic transfers. Three different behaviors can be highlighted in anaerobic digestion: (i) no removal (metals), (ii) removal following dry matter (DM) elimination (organotins and NP) and iii) removal higher than DM (alkylphenols – except NP – BDE 209 and DEHP). Thus, this process allows a clear removal of biodegradable micropollutants which could be potentially significantly improved by increasing DM removal through operational parameters modifications (retention time, temperature, pre-treatment, etc.).     

Variations of metal distribution in sewage sludge composting

In the study, the variations of heavy metal distributions (of Cu, Mn, Pb, and Zn) during the sewage sludge composting process were investigated by sequential extraction procedures. The total content of Cu and Zn in the composted mixture increased after the composting process. Mn and Zn were mainly found in mobile fractions (exchangeable fraction (F1), carbonate fraction (F2), and Fe/Mn oxide fraction (F3)). Cu and Pb were strongly associated with the stable fractions (organic matter/sulfides fraction (F4) and residual fraction (F5)). These five metal fractions were used to calculate the metal mobility (bioavailability) in the sewage sludge and composted mixture. The mobility (bioavailability) of Mn, Pb, and Zn (but not Cu) increased during the composting process. The metal mobility in the composted mixture ranked in the following order: Mn>Zn>Pb>Cu.     

Study of the operational conditions for anaerobic digestion of urban solid wastes

This paper describes an experimental evaluation of anaerobic digestion technology as an option for the management of organic solid waste in developing countries. As raw material, a real and heterogeneous organic waste from urban solid wastes was used. In the first experimental phase, seed selection was achieved through an evaluation of three different anaerobic sludges coming from wastewater treatment plants. The methanization potential of these sludges was assessed in three different batch digesters of 500 mL, at two temperature levels. The results showed that by increasing the temperature to 15 degrees C above room temperature, the methane production increases to three times. So, the best results were obtained in the digester fed with a mixed sludge, working at mesophilic conditions (38-40 degrees C). Then, this selected seed was used at the next experimental phase, testing at different digestion times (DT) of 25, 20 and 18 days in a bigger batch digester of 20 L with a reaction volume of 13 L. The conversion rates were registered at the lowest DT (18 days), reaching 44.9 L/kg(-1) of wet wasteday(-1). Moreover, DT also has a strong influence over COD removal, because there is a direct relationship between solids removal inside the reactor and DT.     

Bioconversion of industrial wastes: paint sludge from automotive manufacturing

The compostability of water-based paint sludge originating from the automotive industry was investigated. Six reactors were operated. Wastewater treatment sludge from the same industry was used as additional substrate, and corncob was used as a bulking agent. The level of paint sludge within the compost mixtures varied between 55 and 85%. All reactors yielded a temperature increase up to thermophilic phase levels (>?40 °C) for a minimum of 5 days, and organic matter and C/N losses were observed. BTEX concentrations decreased during composting. Nickel and tin levels in the final product exceeded the legal compost limits. The calorific value of the compost mixtures increased from 9532 to 18774 kJ/kg at the end of the composting process. It was seen that the process applied in this study can be utilized as a biodrying step before the usage of paint sludge at cement kilns as additional fuel.