金属铁还原脱氯处理有机氯化物的研究进展

本文对金属铁在还原降解六氯乙烷,四氯化碳,氯仿,三氯乙烯,四氯乙烯,二氯乙烯,氯乙烯,五氯酚,多氯联苯等有机氯化物中的应用作了评述,讨论了金属铁降解有机氯化物的反应机理以动力学.     

危险废物中有机物热降解动力学模型

为研究有机危险废物在高温工业窑炉中的协同处置效果,对典型有机物苯和氯乙烯进行热降解实验。将定量的气态苯、氯乙烯和空气的混合物分别通入高温管式炉中煅烧,用气相色谱质谱仪检测尾气中有机物浓度,确定其热降解动力学特性。结果表明:低温阶段苯和、氯乙烯的热降解率随温度较快速增加,高温阶段缓慢增加,1 000℃以上可完全热降解;延长煅烧时间促进苯和氯乙烯的热降解。最终得到苯和氯乙烯的热降解动力学模型,模型可以用于预测危险废物中有机物高温热降解率。     

含铁化合物对有机氯化物的脱氯处理技术研究

综述了钯 /铁、二硫化铁、硫化铁、三氧化二铁、绿锈等含铁化合物在降解六氯乙烷、四氯化碳、五氯乙烷、四氯乙烷、三氯乙烷、三氯乙烯、四氯乙烯等有机氯化物中的应用以及降解机理     

含铁化合物对有机氯化物的脱氯处理技术研究

综述了钯／铁，二硫化铁，硫化铁，三氧化二铁，绿锈等含铁化合物在降在降解六氯乙烷，四氯化碳，五氯乙烷，四氟乙烷，三氯乙烷，三氯乙烯，四氯乙烯等有机氯化物中的应用以及降解机理。     

组合阳极联合气体扩散阴极电催化降解苯胺

采用气体扩散电极为阴极，钛基氧化物（Ti／SnO2-Sb2O5-IrO2）和金属铁构成组合阳极，构建了新型电化学氧化体系用于降解有机污染物。利用该氧化体系，在不同实验条件下考察了苯胺降解的效果与降解过程的相关规律。结果表明，阴极电位、铁阳极通电时间以及苯胺初始浓度均显著影响苯胺的降解效果。当阴极电位为-0．7V，pH3．0，铁阳极通电时间20min时，电化学处理200mg／L苯胺480min，TOC的去除效率达到80．4％，矿化电流效率（MCE）为8．6％，显示了该氧化体系具有良好的有机物降解能力。此外，苯胺降解过程中氨氮和硝态氮浓度的变化表明，苯胺分子中的氮主要转化为NH4和NO3^-。     

以汽油为底物好氧共代谢三氯乙烯

三氯乙烯(trichloroethylene,TCE)是土壤和地下水中广泛存在的有机污染物,好氧生物降解因可将污染物彻底转化成无毒的终产物,一直受到广泛关注,但是TCE好氧降解需要共代谢底物。首次提出以汽油为底物,选取真养产碱杆菌作为活性降解菌株,对地下水中三氯乙烯的好氧共代谢降解进行了初步研究。分别优化了共代谢底物、底物与TCE浓度比、培养基、pH值、盐度、溶解氧等条件,确定了最佳降解条件。当水中TCE的浓度为1 mg/L时,通过对体系预曝氧气,调节汽油浓度为10 mg/L,pH值为5,降解24 h,TCE的降解率可达66.8%。为修复同时被汽油和TCE污染的场地提供了一个新的研究方向。     

纳米级铁粉脱氯降解四氯化碳

四氯化碳的生产和使用,给人类带来了较大危害.为此,采用纳米铁粉这一新方法对其进行脱氯处理.试验以纳米级铁粉对四氯化碳的脱氯率为考察指标,选用L25(56)正交试验方案,考察了降解介质的初始pH值、纳米铁粉的质量、降解温度、摇床转速和脱氯时间5个影响因素.结果表明,pH值这一因素有极显著影响;在得出的纳米铁粉对四氯化碳脱氯的最佳工艺条件下,获得了99.5%的脱氯率,为有机氯化物脱氯开辟了一条新途径.     

纳米级铁粉脱氯降解四氯化碳

四氯化碳的生产和使用，给人类带来了较大危害。为此，采用纳米铁粉这一新方法对其进行脱氯处理。试验以纳米级铁粉对四氯化碳的脱氯率为考察指标，选用L25（5^6）正交试验方案，考察了降解介质的初始pH值、纳米铁粉的质量、降解温度、摇床转速和脱氯时间5个影响因素。结果表明，pH值这一因素有极显著影响；在得出的纳米铁粉对四氯化碳脱氯的最佳工艺条件下，获得了99．5％的脱氯率，为有机氯化物脱氯开辟了一条新途径。     

燃煤引起的有机氯污染

氯是煤中的有害元素之一,煤燃烧时氯一部分以ＨＣｌ的形式释放出来,一部分则生成三致剧毒有机氯化物－－二恶英和呋喃。重点介绍了燃煤引起的有机氯化物地环境的污染与 及它的形成机理,形成条件、煤质影响和它的传输方式,对氯污染的评价与防治有重要的意义。     

2,2-二氯乙烯基二甲基磷酸酯在TiO2/H2O界面上光催化降解

实验研究了２,２－二氯乙烯基二甲基磷酸酯在ＴｉＯ２／Ｈ２Ｏ界面上光催化降解的最适空气通入量,初始ＰＨ值, 不同浓度的调变性助催经剂Ｆｅ＾３＋、Ａｇ＾＋在供Ｏ２条件下对ＴｉＯ２光催化降解有机磷速率的影响。     

Antimony toxicity in the lichen Xanthoria parietina (L.) Th. Fr.

In this paper we tested if treating the lichen Xanthoria parietina with Sb-containing solutions causes Sb bioaccumulation as well as physiological and ultrastructural changes. Total and intracellular antimony content in Sb-treated samples increased progressively with increasing concentration in the treatment solutions. Incubation of X. parietina thalli with Sb at concentrations as low as 0.1 mM caused a decrease in sample viability, measured as intensity of respiratory activity, and damage to cell membranes, expressed in terms of membrane lipid peroxidation, as well as ultrastructural changes such as plasmolysis, impairment of the thylakoid system of the alga and cytoplasmic lipid droplets. The photosynthetic system hardly responded, at least under the tested experimental conditions.     

Green pre-concentration techniques during pesticide analysis in food samples

The ever-increasing demand for determining pesticides at low concentration levels in different food matrices requires a preliminary step of pre-concentration which is considered a crucial stage. Recently, the parameter of “greenness” during sample pre-concentration of pesticides in food matrices is as important as selectivity in order to avoid using harmful organic solvents during sample preparation. Developing new green pre-concentration techniques is one of the key subjects. Thus, to reduce the impact on the environment during trace analysis of pesticides in food matrices, new developments in pre-concentration have gone in three separate directions: the search for more environmentally friendly solvents, miniaturization and development of solvent-free pre-concentration techniques. Eco-friendly solvents such as supercritical fluids, ionic liquids and natural deep eutectic solvents have been developed for use as extraction solvents during pre-concentration of pesticides in food matrices. Also, miniaturized pre-concentration techniques such as QuEChERS, dispersive liquid–liquid micro-extraction and hollow-fiber liquid-phase micro-extraction have been used during trace analysis of pesticides in food samples as well as solvent-free techniques such as solid-phase micro-extraction and stir bar sorptive extraction. All these developments which are aimed at ensuring that pesticide pre-concentration in different food matrices is green are critically reviewed in this paper.     

The evolution of mass balance models of persistent organic pollutant fate in the environment

Current approaches to modelling the fate of persistent organic pollutants (POPs) in the environment have evolved in response to four dominant characteristics of these substances; namely: (1) the presence of POPs in virtually all environmental phases and the ease with which they move from one to the other requires multi-compartmental modelling. Describing transport across phase boundaries becomes as, or even more, important as quantifying transport within the phases; (2) POPs may persist in the environment for many decades. For chemicals that 'have time', concepts such as equilibrium partitioning and steady-state become more important than for short-lived substances whose fate is more controlled by the rates of transformation; (3) measuring POPs is difficult and expensive and observed concentrations of POPs are not available in high spatial or temporal resolution. Consequently, high resolution tends not to be a high priority in POP models; and (4) detrimental effects of POPs often manifest themselves in top predators, which has led to a focus on modelling biotic uptake and transfer within food chains. The task of building a POPs model is viewed as combining the four 'building blocks' of partitioning, transport, transformation and source data with the help of the law of the conservation of mass. Process models, evaluative models, models of real local, regional and global fate, as well as biological uptake models are presented and references to numerous examples are provided. An attempt is made to forecast future directions in the field of POPs modelling. It is expected that modelling techniques that do not rely on quantitative emission estimates as well as approaches that take into account spatial, temporal and climatic variability as well as parameter uncertainty will increase in importance. Finally, the relationship between modelling POPs and models of other pollutant issues is addressed, as are potential interactions between POPs and pollutant issues such as eutrophication, acidification and global climate change.     

Heterogeneous water phase catalysis as an environmental application: a review

Catalytic water phase processes as an environmental application is a relatively novel subject with tremendous potential in the near future. This review of 120 references presents the wide scale of heterogeneous water phase applications studied mainly within past five years. Both oxidation and hydrogenation processes are included as well as TiO₂ assisted photocatalysis. According to the references, heterogeneous catalysis is developing rapidly. New bimetallic catalysts and supports with higher surface area have improved catalytic efficiency in both oxidation and hydrogenation processes. It also seems that study on use of some waste materials such as red mud as catalyst is a very progressive field. On the whole, the chemical aspects are pretty well known, but the catalyst durability, and in many cases activity as well, has to be improved.     

Textural and chemical properties of swine-manure-derived biochar pertinent to its potential use as a soil amendment

Biochars have received increasing attention in recent years because of their properties pertaining to soil fertility and contaminant immobilization as well as serving as carbon sinks. In this work, a series of biochars were produced from dried swine manure waste by slow pyrolysis at different temperatures (i.e., 673-1073 K). The characterization of the resulting biochars was examined for its relevance to its potential use as soil amendment. It was found that the pore properties, ash contents and pH values of all swine-manure-derived biochars basically increased as temperature increased, while the yield and nitrogen/oxygen contents decreased with increasing temperature as a result of pyrolytic volatilization during pyrolysis. From the organic and inorganic elements analyses, the manure-derived biochar was rich in soil nutrients such as N, P, Ca, Mg, and K. Furthermore, the pore, surface and chemical properties were also consistent with the observations of the SEM-EDS, XRD and FTIR. This result suggested that the mesoporous manure-derived biochar could be used as an excellent medium to soil environment.     

Toxic effects of arsenic on Sinorhizobium-Medicago sativa symbiotic interaction

Recently, the Rhizobium-legume symbiotic interaction has been proposed as an interesting tool in bioremediation. However, little is known about the effect of most common contaminants on this process. The phytotoxic effects of arsenic on nodulation of Medicago sativa have been examined in vitro using the highly arsenic resistant and symbiotically effective Sinorhizobium sp. strain MA11. The bacteria were able to grow on plates containing As concentrations as high as 10 mM. Nevertheless, as little as 25-35 microM arsenite produced a 75% decrease in the total number of nodules, due to a 90% reduction in the number of rhizobial infections, as could be determined using the strain MA11 carrying a lacZ reporter gene. This effect was associated to root hair damage and a shorter infective root zone. However, once nodulation was established nodule development seemed to continue normally, although earlier senescence could be observed in nodules of arsenic-grown plants.     

指示水体病原污染的微生物及其检测

受粪便污染的水体可能含有严重威胁人类和动物健康的致病微生物,由于病原微生物在水环境中往往数量较少、检测比较困难,通常采用检测与病原微生物具有密切关系的指示微生物来指示和估计病原污染.指示微生物包括总大肠菌群及其替代微生物,已被广泛应用于水体污染程度检测等方面.总结了各种指示微生物的特性、应用范围以及检测方法等方面的最新研究进展.初步介绍了指示微生物和水环境之间的关系,着重介绍了判断病原微生物污染来源的指示微生物及其最新检测方法.     

Brominated-chlorinated diphenyl ethers formed by thermolysis of polybrominated diphenyl ethers at low temperatures

Polybrominated diphenyl ethers (PBDEs) are a group of brominated flame retardants (BFRs) used mainly as additives in different kinds of plastic material. Various PBDEs are found in all environmental compartments as well as in tissue and blood serum of animals and humans due to their persistence and tendency to bioaccumulate. Emission of PBDEs into the environment can occur during recycling of PBDE-containing plastic material or during their uncontrolled or insufficient combustion as e.g. in accidental fires or landfill fires. Under these circumstances, PBDEs can also function as precursor molecules for the formation of polybrominated dibenzodioxins (PBDDs) and dibenzofurans (PBDFs). In this study, we qualitatively investigated the reaction of two PBDE congeners, 2,2′,4,4′-tetrabromo diphenyl ether (BDE 47) and 2,2′,4,4′,5,5′-hexabromo diphenyl ether (BDE 153), as well as hexabromobenzene (HBB), a flame retardant used in the past, when exposed to temperatures between 250 °C and 500 °C. The formed reaction products were analysed by high resolution gas chromatography–low resolution mass spectrometry (HRGC-LRMS). Among others brominated–chlorinated diphenyl ethers were formed by chlorodebromination of the PBDEs. In addition, thermolysis of BDE 47 and BDE 153 in the presence of tetrachloromethane as model substance for an organic chlorine source was studied. Thermal treatment of HBB resulted in the formation of brominated–chlorinated benzenes.     

基于指标规范值的环境质量的指数幂乘积指数公式

传统的环境质量指数幂乘积指数的分级标准值随指标不同和指标数目不同而不同,因而综合指数的分级标准值不能规范和统一.在适当设定指标参照值和指标值的规范变换式基础上,使同类环境不同指标的同级标准的规范值差异尽可能小,而不同标准的指标规范值差异尽可能大,从而可以认为,用规范值表示的同类环境的各指标皆等效于某个规范指标,因而同类环境的任意m项指标的指数幂乘积综合指数可以有共同的分级标准值,使基于指标规范值的环境质量指数幂乘积指数公式具有普适性、可比性和通用性.     

Data ranges in aquatic toxicity of chemicals

A significant problem for effect assessment of aquatic ecosystems arises from the large ranges of toxicity data, which can be found in different databases and literature. Here, ranges are given for the aquatic toxicity of 27 high production volume chemicals. Based on these illustrative examples and on the current literature on uncertainty in aquatic effect assessment, toxicity ranges are discussed for their possible causes (variation in experimental condition, species, endpoint, time) and ways to handle them (safety factors). Implications and recommendations on the procedure of risk analysis of chemical substances are drawn. Two main requirements for a comprehensive risk assessment are identified, which often play a minor role in current practice (as they are often neglected) as well as in scientific discussion (as they are meant to be trivial). First, data quality must be checked critically before applying any result of a toxicity test. Secondly, experimental data should take into account different species and acute as well as chronic data. If these aspects are considered in risk analysis, which is common practice in ecotoxicology but not always in the context of practical applications in risk engineering, a more comprehensive picture of the environmental toxicity of a chemical substance can be obtained.