Studies of the coarse particle (2.5–10 μm) component in UK urban atmospheres

An analysis is presented of continuous simultaneous measurement data for PM₁₀ and PM_2.5 using TEOM instruments from five sites in the United Kingdom. The results are analysed specifically in relation to the sources and processes influencing the coarse particle fraction (2.5–10 μm). The data show a generally strong correlation between fine and coarse particle concentrations at all sites, with a generally higher proportion of coarse particles in the dryer months of the year. The one rural site shows a notably lower proportion of coarse particles than the urban and suburban sites. Whilst it is possible to disaggregate the coarse particle concentrations into a component which is diluted by increasing windspeed and a component which increases with windspeed and is hence possibly attributable to wind-induced resuspension processes, the latter is only a minor proportion of the total coarse particle concentration. There are appreciable weekday-to-weekend and day-to-night differences between coarse particle concentrations which are most marked at the urban sites indicative of anthropogenic activities being a source of coarse particles. The clearest indication of the likely predominant source of coarse particles arises from an analysis of a data set derived from an urban street canyon site after subtraction of measurements from a nearby urban background location. The data indicate strong relationships of both fine and coarse incremental particle concentrations in the street canyon with incremental NO_x. If incremental fine particles and coarse particles are attributed to exhaust emissions and vehicle-induced resuspension, respectively, then it may be concluded that vehicle-induced resuspension provides a source strength approximately equal to that of exhaust emissions. An analysis of the coarse particle concentration data suggest that episodes of elevated coarse particle concentrations alone very rarely lead to exceedence of the UK air quality standard for PM₁₀ of 50 μg m⁻³ measured as a 24-h running mean.     

Urban emissions measured with aircraft

Detailed knowledge of the quantity and composition of urban emissions is a prerequisite for successful application of atmospheric models to predict transport and distribution of primary and secondary air pollutants in the troposphere. We investigate the prospects and limitations of aircraft measurements in the determination of emission fluxes from urban areas. Our analysis focuses on data collected in September 1994 in and around Athens, Greece. Generally, emission fluxes from cities can be quantified with aircraft and with the minimum acceptable precision (uncertainty better than a factor of 2) only under very favorable meteorological conditions, namely in a homogeneous flow field in a well-mixed boundary layer. Better accuracy can be achieved only through ensemble averaging of repeated measurements. From our measurements in the Athens area, we deduced relative emission ratios of pollutant gases. With the support of ground-based measurements in a street canyon, the emission ratios NOx/CO, SO2/CO, and volatile organic compounds/CO (34 individual VOCs) could be determined with high precision. These results are very useful in analyzing differences between various existing emission inventories. Our data for VOCs reveal that the non-traffic emissions are of the same magnitude as the emissions originating from traffic.     

Estimation of particle resuspension source strength on a major London Road

Non-exhaust particles from road traffic arise from both abrasion sources and the resuspension of particles from the road surface. This paper reports a new combination of existing methods for indirect estimation of resuspension emission factors for Marylebone Road, London, a busy multi-lane highway in a street canyon. The method involves firstly estimating the total source strength of coarse particles (PM_2.5–10) arising from the road by calculating the roadside incremental concentration of coarse particles above the urban background. This is converted to a source strength by its ratio to NO_x whose source strength is estimated from the knowledge of the traffic mix and mean speed. This coarse particle source strength is assumed to represent the sum of resuspension emissions and the coarse particle component of abrasion emissions. Using information on the traffic mix and speed, the abrasion emissions have been calculated from the EMEP/CORINAIR emissions factor database, the result subtracted from the total coarse particle emissions in order to yield resuspension emissions, and combined with traffic count data to derive fleet-average emission factors. Using the fact that the traffic mix differs substantially between weekdays and weekends, separate average emission factors for light- and heavy-duty vehicles have been estimated. In addition to traffic mix, the influence of wind speed and the time elapsed since the last rainfall upon resuspension have been estimated. Wind speed was found to have by far the larger influence, although this was still secondary to the number of heavy-duty vehicles. Uncertainties arising from the choice of urban background site and poor data quality are discussed.     

Influence of trees on the dispersion of pollutants in an urban street canyon—Experimental investigation of the flow and concentration field

Flow field and concentration measurements have been performed in an idealized model of an urban street canyon with one row of trees arranged along the center axis. The model was set up in an atmospheric boundary layer wind tunnel and the approach flow was directed perpendicular to the street axis. A line source embedded in the bottom of the street was used to release tracer gas for the simulation of traffic exhaust emissions. Trees with spherical crowns were modeled and positioned inside the street canyon, varying crown diameter, crown permeability, trunk height and tree spacing. Traffic-induced turbulence was simulated by rotating belts with thin plates. Concentrations were measured at the facades of the street canyon. For small tree crowns, only little changes in concentration were measured, however, increasing crown diameters led to increasing concentrations at the leeward street canyon wall associated with a reduction of local concentrations at the windward wall. For some cases, a variation of trunk height led to a modification of the concentration pattern on the walls. Increasing the tree spacing resulted in a noticeable concentration decrease. When compared to the situation with standing (but emitting) traffic, the traffic-induced turbulence by two-way car movements always contributed to a more homogenous concentration field inside the street canyon yielding to reduced mean concentration levels.     

Numerical modeling on air quality in an urban environment with changes of the aspect ratio and wind direction

Due to heavy traffic emissions within an urban environment, air quality during the last decade becomes worse year by year and hazard to public health. In the present work, numerical modeling of flow and dispersion of gaseous emissions from vehicle exhaust in a street canyon were investigated under changes of the aspect ratio and wind direction. The three-dimensional flow and dispersion of gaseous pollutants were modeled using a computational fluid dynamics (CFD) model which was numerically solved using Reynolds-averaged Navier–Stokes (RANS) equations. The diffusion flow field in the atmospheric boundary layer within the street canyon was studied for different aspect ratios (W/H?=?1/2, 3/4, and 1) and wind directions (θ?=?90°, 112.5°, 135°, and 157.5°). The numerical models were validated against wind tunnel results to optimize the turbulence model. The numerical results agreed well with the wind tunnel results. The simulation demonstrated that the minimum concentration at the human respiration height within the street canyon was on the windward side for aspect ratios W/H?=?1/2 and 1 and wind directions θ?=?112.5°, 135°, and 157.5°. The pollutant concentration level decreases as the wind direction and aspect ratio increase. The wind velocity and turbulence intensity increase as the aspect ratio and wind direction increase.     

A Lagrangian stochastic model for predicting concentration fluctuations in urban areas

A combined Lagrangian stochastic model with a micromixing sub-model is used to estimate the fluctuating concentrations observed in two wind tunnel experiments. The Lagrangian stochastic model allows fluid trajectories to be simulated in the inhomogeneous flow, while the mixing model accounts for the dissipation of fluctuations using the interaction by exchange with the mean (IEM) mechanism. The model is first tested against the open terrain, wind tunnel data of Fackrell, J.E. and Robins, A.E. [1982. Concentration fluctuations and fluxes in plumes from point sources in a turbulent boundary layer. Journal of Fluid Mechanics 117, 1–26] and shows good agreement with the observed mean concentrations and fluctuation intensities. The model is then compared with the wind tunnel simulation of a two-dimensional street canyon by Pavageau, M. and Schatzmann, M. [1999. Wind tunnel measurements of concentration fluctuations in an urban street canyon. Atmospheric Environment 33, 3961–3971]. Despite the limitations of the k–ε turbulence scheme and the IEM mixing mechanism, the model reproduces the fluctuation intensity pattern within the canyon well. Overall, the comparison with both sets of wind tunnel experiments are encouraging, and the simplicity of the model means that predictions in a complex, three-dimensional geometry can be produced in a practicable amount of time.     

Particle emission factors during cooking activities

Exposure to particles emitted by cooking activities may be responsible for a variety of respiratory health effects. However, the relationship between these exposures and their subsequent effects on health cannot be evaluated without understanding the properties of the emitted aerosol or the main parameters that influence particle emissions during cooking. Whilst traffic-related emissions, stack emissions and concentrations of ultrafine particles (UFPs, diameter < 100 nm) in urban ambient air have been widely investigated for many years, indoor exposure to UFPs is a relatively new field and in order to evaluate indoor UFP emissions accurately, it is vital to improve scientific understanding of the main parameters that influence particle number, surface area and mass emissions. The main purpose of this study was to characterise the particle emissions produced during grilling and frying as a function of the food, source, cooking temperature and type of oil. Emission factors, along with particle number concentrations and size distributions were determined in the size range 0.006–20 μm using a Scanning Mobility Particle Sizer (SMPS) and an Aerodynamic Particle Sizer (APS). An infrared camera was used to measure the temperature field. Overall, increased emission factors were observed to be a function of increased cooking temperatures. Cooking fatty foods also produced higher particle emission factors than vegetables, mainly in terms of mass concentration, and particle emission factors also varied significantly according to the type of oil used.     

PM10 emission factors for non-exhaust particles generated by road traffic in an urban street canyon and along a freeway in Switzerland

Recent studies have shown clear contributions of non-exhaust emissions to the traffic related PM10 load of the ambient air. These emissions consist of particles produced by abrasion from brakes, road wear, tire wear, as well as vehicle induced resuspension of deposited road dust. The main scope of the presented work was to identify and quantify the non-exhaust fraction of traffic related PM10 for two roadside locations in Switzerland with different traffic regimes. The two investigated locations, an urban street canyon with heavily congested traffic and an interurban freeway, are considered as being typical for Central Europe. Mass-relevant contributions from abrasion particles and resuspended road dust mainly originated from particles in the size range 1–10 μm. The results showed a major influence of vehicle induced resuspension of road dust. In the street canyon, the traffic related PM10 emissions (LDV: 24 ± 8 mg km^?1 vehicle^?1, HDV: 498 ± 86 mg km^?1 vehicle^?1) were assigned to 21% brake wear, 38% resuspended road dust and 41% exhaust emissions. Along the freeway (LDV: 50 ± 13 mg km^?1 vehicle^?1, HDV: 288 ± 72 mg km^?1 vehicle^?1), respective contributions were 3% brake wear, 56% resuspended road dust and 41% exhaust emissions. There was no indication for relevant contributions from tire wear and abrasion from undamaged pavements.     

Fast response measurements of the dispersion of nanoparticles in a vehicle wake and a street canyon

The distributions of nanoparticles (below 300 nm in diameter) change rapidly after emission from the tail pipe of a moving vehicle due to the influence of transformation processes. Information on this time scale is important for modelling of nanoparticle dispersion but is unknown because the sampling frequencies of available instruments are unable to capture these rapid processes. In this study, a fast response differential mobility spectrometer (Cambustion Instruments DMS500), originally designed to measure particle number distributions (PNDs) and concentrations in engine exhaust emissions, was deployed to measure particles in the 5–1000 nm size range at a sampling frequency of 10 Hz. This article presents results of two separate studies; one, measurements along the roadside in a Cambridge (UK) street canyon and, two, measurements at a fixed position (20 cm above road level), centrally, in the wake of a single moving diesel-engined car. The aims of the first measurements were to test the suitability and recommend optimum operating conditions of the DMS500 for ambient measurements. The aim of the second study was to investigate the time scale over which competing influences of dilution and transformation processes (nucleation, condensation and coagulation) affect the PNDs in the wake of a moving car. Results suggested that the effect of transformation processes was nearly complete within about 1 s after emission due to rapid dilution in the vehicle wake. Furthermore, roadside measurements in a street canyon showed that the time for traffic emissions to reach the roadside in calm wind conditions was about 45 ± 6 s. These observations suggest the hypothesis that the effects of transformation processes are generally complete by the time particles are observed at roadside and the total particle numbers can then be assumed as conserved. A corollary of this hypothesis is that complex transformation processes can be ignored when modelling the behaviour of nanoparticles in street canyons once the very near-exhaust processes are complete.     

The influence of aerosol dynamics on indoor exposure to airborne DEHP

A mass-balance model was extended to investigate the influence of aerosol particles on the accumulation of indoor airborne DEHP, which allows the consideration of a variable particle concentration. The calculated gas-phase di-2-ethylhexyl phthalate (DEHP) concentration is consistent with those measured within residences in both the United States and Europe. Model predictions suggest that there are differences of more than 10% of particle-phase DEHP concentrations between the variable-particle-concentration case and the constant one for over half (578 days) within the calculation time of 1000 days. Airborne DEHP consists primarily of a particle phase. The exposure data indicate that the influence of particle dynamics remains significant throughout the calculation period, and the size fraction of 0–0.5 μm contributes the most, at 39.1%, to the total exposure to particle-phase DEHP as a result of a strong “source” effect which brings particles into the indoor air and a weak “sink” effect which removes particles from the indoor air. The sensitivity analysis indicates that deposition exhibits the most apparent influence, and particle emission from cooking is a significant factor, as cooking is the main source of particles in the size fraction of 0–0.5 μm. The sensitivity analysis also shows that particle penetration has a less obvious influence on the exposure to airborne DEHP because air exchange rate caused penetration introduces and removes particles simultaneously, thus having a limited influence on the airborne DEHP; while resuspension exhibits the weakest influence because it contributes little to the small particles which are the main component of aerosol particles indoors. Strategies for enhancing deposition and reducing particle emissions from cooking and penetration may be helpful to reduce residents’ exposure to airborne SVOCs.     

Elk River Completes Second Year With Zero Bag Failures Reported

Abstract

This paper presents results from a study conducted in two urban areas of southern California, Downey and Riverside, to examine the effect of different sources and formation mechanisms on the size distribution and temporal trends of ultrafine particles. Near-continuous data were collected for 5 months at each location. Our data clearly identified Downey as a source site, primarily affected by vehicular emissions from nearby freeways, and Riverside as a receptor site, where photochemical secondary reactions form a substantial fraction of particles, along with local vehicular emissions. In Downey, the diurnal trends of total particle number concentration and elemental carbon (EC) appear to be almost identical throughout the day and irrespective of season, thereby corroborating the role of primary emissions in the formation of these particles. This agreement between EC and particle number was not observed in Riverside during the warmer months of the year, while very similar trends to Downey were observed during the winter months in that area. Similarly, the size distribution of ultrafine particles in Downey was generally unimodal with a mode diameter of 30–40 nm and without significant monthly variations. The number-based particle size distributions obtained in Riverside were bimodal, with a significant increase in accumulation mode as the season progressed from winter to summer. During the warmer months, there was also an increase in sub-100-nm particles in the afternoon hours, between 2:00 p.m. and 4:00 p.m., that also increased with the temperature. The differences observed in the ultrafine particle distribution and temporal trends clearly demonstrated that mechanisms other than direct emissions play an important role in the formation of ultrafine particles in receptor sites of the Los Angeles Basin.     

Urban scale modeling of particle number concentration in Stockholm

A three-dimensional dispersion model has been implemented over the urban area of Stockholm (35×35 km) to assess the spatial distribution of number concentrations of particles in the diameter range 3–400 nm. Typical number concentrations in the urban background of Stockholm is 10 000 cm⁻³, while they are three times higher close to a major highway outside the city and seven times higher within a densely trafficked street canyon site in the city center. The model, which includes an aerosol module for calculating the particle number losses due to coagulation and dry deposition, has been run for a 10-day period. Model results compare well with measured data, both in levels and in temporal variability. Coagulation was found to be of little importance in terms of time averaged concentrations, contributing to losses of only a few percent as compared to inert particles, while dry deposition yield particle number losses of up to 25% in certain locations. Episodic losses of up to 10% due to coagulation and 50% due to deposition, are found some kilometers downwind of major roads, rising in connection with low wind speed and suppressed turbulent mixing. Removal due to coagulation and deposition will thus be more significant for the simulation of extreme particle number concentrations during peak episodes.The study shows that dispersion models with proper aerosol dynamics included may be used to assess particle number concentrations in Stockholm, where ultrafine particles principally originate from traffic emissions. Emission factors may be determined from roadside measurements, but ambient temperature must be considered, as it has a strong influence on particle number emissions from vehicles.     

Application of a Three-Layer Photochemical Box Model in an Athens Street Canyon

ABSTRACT

The aim of this paper is to show that a photochemical box model could describe the air pollution diurnal profiles within a typical street canyon in the city of Athens. As sophisticated three-dimensional dispersion models are computationally expensive and they cannot serve to simulate pollution levels in the scale of an urban street canyon, a suitably modified three-layer photochemical box model was applied. A street canyon of Athens with heavy traffic was chosen to apply the aforementioned model. The model was used to calculate pollutant concentrations during two days with meteorological conditions favoring pollutant accumulation. Road traffic emissions were calculated based on existing traffic load measurements. Meteorological data, as well as various pollutant concentrations, in order to compare with the model results, were provided by available measurements. The calculated concentrations were found to be in good agreement with measured concentration levels and show that, when traffic load and traffic composition data are available, this model can be used to predict pollution episodes. It is noteworthy that high concentrations persisted, even after additional traffic restriction measures were taken on the second day because of the high pollution levels.     

Three-dimensional modeling of air flow and pollutant dispersion in an urban street canyon with thermal effects

Effects of excess ground and building temperatures on airflow and dispersion of pollutants in an urban street canyon with an aspect ratio of 0.8 and a length-to-width ratio of 3 were investigated numerically. Three-dimensional governing equations of mass, momentum, energy, and species were modeled using the RNG k-epsilon turbulence model and Boussinesq approximation, which were solved using the finite volume method. Vehicle emissions were estimated from the measured traffic flow rates and modeled as banded line sources, with a street length and bandwidths equal to typical vehicle widths. Both measurements and simulations reveal that pollutant concentrations typically follow the traffic flow rate; they decline as the height increases and are higher on the leeward side than on the windward side. Three-dimensional simulations reveal that the vortex line, joining the centers of cross-sectional vortexes of the street canyon, meanders between street buildings and shifts toward the windward side when heating strength is increased. Thermal boundary layers are very thin. Entrainment of outside air increases, and pollutant concentration decreases with increasing heating condition. Also, traffic-produced turbulence enhances the turbulent kinetic energy and the mixing of temperature and admixtures in the canyon. Factors affecting the inaccuracy of the simulations are addressed.     

Application of the k–ε turbulence model to the high Reynolds number skimming flow field of an urban street canyon

A two-dimensional, steady, k–ε turbulence model was used to investigate the high Reynolds number skimming flow field of an urban street canyon. We describe the critical canyon width-to-height ratios that distinguish a cascade of vortex patterns that form in an urban street canyon. Details of the flow field are reported that includes the structure of the mean flow field, turbulent kinetic energy, turbulent length scale, turbulent eddy viscosity, and Reynolds stress for three typical different aspect ratios, W/H, of a street canyon. The consequences of vortex layering on vertical transport are explored.     

Dynamic of submicrometer particles in urban environment

Many studies show that particle toxicity increases with decreasing their size, emphasizing the role of submicrometric particles, in particular of ultrafine particles (<100 nm). In fact, particles greater than 2.5 μm are quickly removed through dry and wet deposition on the timescale of hours whereas submicrometer particles may reside in atmosphere for weeks, penetrate in indoor environment, and be long-range transported. High aerosol size resolution measurements are important for a correct assessment of the deposition efficiency in the human respiratory system, and time resolution is another important requisite. Starting from such considerations, time-resolved aerosol particle number size distributions have been measured in downtown Rome. Fast Mobility Particle Sizer (FMPS) and Scanning Mobility Particle Sizer (SMPS) measurements have been carried out at the INAIL’s Pilot Station, located in downtown Rome, in an area characterized by high density of autovehicular traffic. The two instruments have allowed to investigate deeply the urban aerosol in the range of 5.6–560 and 3.5–117 nm, respectively. In particular, the FMPS measurements have confirmed the interpretation about the transition phenomena in the time interval of few seconds, timescale typically associated with the emission of gasoline and diesel engines. In downtown Rome, the hourly average size distribution is bimodal or trimodal with maxima at about 5–15, 20–30, and 70–100 nm. Particle formation in the nucleation mode was associated to freshly emitted autovehicular exhaust.     

Wintertime size distribution of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in the urban environment: Street- vs rooftop-level measurements

The size distribution of ambient air particles and associated organic pollutants, such as polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), and organochlorine pesticides (OCPs) including hexachlorocyclohexanes (HCHs), DDT and metabolites, etc., was investigated at a traffic-impacted site of Thessaloniki, Greece. Investigation took place during wintertime of 2006 at two heights above ground: at the street level (1.5 m) and at the rooftop level (15 m). Size-resolved samples (<0.95 μm, 0.95–1.5 μm, 1.5–3 μm, 3–7.5 μm and >7.5 μm) were concurrently collected from the two height levels using five-stage high volume cascade impactors. At both heights, particle mass exhibited bimodal distribution with peaks in the 0.95–1.5 μm and the 3–7.5 μm size fractions, whereas most organic pollutants exhibited one peak at 0.95–1.5 μm. Apart from the 0.95–1.5 μm fraction, particle concentrations of all size ranges were significantly higher at the street level than at the rooftop as a result of more intensive vehicular emissions and road dust resuspension. On the contrary, the concentrations of most organic pollutants did not differentiate significantly between the two elevations.     

Roadside measurements of fine and ultrafine particles at a major road north of Gothenburg

Particle measurements were conducted at a road site 15 km north of the city of Gothenburg for 3 weeks in June 2000. The size distribution between 10 and 368 nm was measured continuously by using a differential mobility particle sizer (DMPS) system. PM_2.5 was sampled on a daily basis with subsequent elemental analysis using EDXRF-spectroscopy. The road is a straight four-lane road with a speed limit of 90 kph. The road passing the site is flat with no elevations where the vehicles run on a steady workload and with constant speed. The traffic intensity is about 20,000 cars per workday and 13,000 vehicles per day during weekends. The diesel fuel used in Sweden is low in sulphur content (<10 ppm) and therefore the diesel vehicles passing the site contribute less to particle emissions in comparison with other studies. A correlation between PM_2.5 and accumulation mode particles (100–368 nm) was observed. However, no significant correlation was found between number concentrations of ultrafine particles (10–100 nm) and PM_2.5 or the accumulation mode number concentration. The particle distribution between 10 and 368 nm showed great dependency on wind speed and wind direction, where the wind speed was the dominant factor for ultrafine (10–100 nm) particle concentrations. The difference in traffic intensity between workday and weekend together with wind data made it possible to single out the traffic contribution to particle emissions and measure the size distribution. The results presented in combination with previous studies show that both PM_2.5 and the mass of accumulation mode particles are bad estimates for ultrafine particles.     

Measurements of the physical properties of particles in the urban atmosphere

Measurements of the physical properties of particles in the atmosphere of a UK urban area have been made, including particle number count by condensation nucleus counters with different lower particle size cut-offs; particle size distributions using a Scanning Mobility Particle Sizer; total particle Fuchs surface area using an epiphaniometer and particle mass using Tapered Element Oscillating Micro-balance (TEOM) instruments with size selective (PM₁₀ and PM_2.5) inlets. Mean particle number counts at three sites range from 2.86×10⁴ to 9.60×10⁴ cm^-3. A traffic-influenced location showed a substantially higher ratio of particle number to PM₁₀ mass than a nearby background location despite being some 70 m from the roadway. Operating two condensation nucleus counters in tandem to determine particles in the 3–7 nm size range by difference showed signficant numbers of particles in this range, apparently related to homogeneous nucleation processes. Measurements with the Scanning Mobility Particle Sizer showed a clear difference between roadside size distributions and those at a nearby background location with an additional mode in the roadside samples below 10 nm diameter. Particle number counts were found to show a significant linear correlation with PM₁₀ mass (r²=0.44; n=44 for 24 h data at an urban background location), although during one period of high pollution a curvilinear relationship was found. Measurements of the diurnal variation in PM₁₀ mass, particle number count and Fuchs surface area show the same general pattern of behaviour of the three variables, explicable in terms of vehicle emission source strength and atmospheric dispersion, although the surface area growth was out of phase with the particle number and mass. It appears that particle number gives the clearest indication of recent road traffic emissions.     

Simulation of wind-driven dispersion of fire pollutants in a street canyon using FDS

Air quality in urban areas attracts great attention due to increasing pollutant emissions and their negative effects on human health and environment. Numerous studies, such as those by Mouilleau and Champassith (J Loss Prevent Proc 22(3): 316–323, 2009), Xie et al. (J Hydrodyn 21(1): 108–117, 2009), and Yassin (Environ Sci Pollut Res 20(6): 3975–3988, 2013) focus on the air pollutant dispersion with no buoyancy effect or weak buoyancy effect. A few studies, such as those by Hu et al. (J Hazard Mater 166(1): 394–406, 2009; J Hazard Mater 192(3): 940–948, 2011; J Civ Eng Manag (2013)) focus on the fire-induced dispersion of pollutants with heat buoyancy release rate in the range from 0.5 to 20 MW. However, the air pollution source might very often be concentrated and intensive, as a consequence of the hazardous materials fire. Namely, transportation of fuel through urban areas occurs regularly, because it is often impossible to find alternative supply routes. It is accompanied with the risk of fire accident occurrences. Accident prevention strategies require analysis of the worst scenarios in which fire products jeopardize the exposed population and environment. The aim of this article is to analyze the impact of wind flow on air pollution and human vulnerability to fire products in a street canyon. For simulation of the gasoline tanker truck fire as a result of a multivehicle accident, computational fluid dynamics large eddy simulation method has been used. Numerical results show that the fire products flow vertically upward, without touching the walls of the buildings in the absence of wind. However, when the wind velocity reaches the critical value, the products touch the walls of the buildings on both sides of the street canyon. The concentrations of carbon monoxide and soot decrease, whereas carbon dioxide concentration increases with the rise of height above the street canyon ground level. The longitudinal concentration of the pollutants inside the street increases with the rise of the wind velocity at the roof level of the street canyon.