常温下基质与时间对ANAMMOX污泥活性保藏影响

采用厌氧氨氧化污泥,通过脱氮效能的测定,研究了常温（15±2）℃下保藏过程中基质添加与保藏时间对污泥活性的影响以及探讨长期保持污泥活性的保藏策略。结果表明,在无营养物添加的情况下,保藏的前45天厌氧氨氧化污泥氮去除速率由0.107 kg/（m3·d）下降到0.025 kg/（m3·d）,其速率下降最快,但是经过6 d培养,污泥的活性可以得到恢复;当保藏365 d后,厌氧氨氧化污泥活性基本消失,即使通过11 d恢复也无明显的厌氧氨氧化特性。说明常温下保藏时间对厌氧氨氧化污泥活性影响显著,随着保藏时间的延长污泥氮去除速率会大幅降低,甚至消失。根据衰减指数模型拟合出常温状态下厌氧氨氧化污泥活性衰减模型为y=0.547×exp（-0.0109×t）。通过定期（15 d）投加营养物,经过150d和365 d保藏后的厌氧氨氧化污泥仍然保持48%和31%的活性。说明定期投加营养物可以有效缓解厌氧氨氧化污泥活性在常温保藏过程中的衰减,适用于厌氧氨氧化污泥常温下长期保藏。     

氯化钙控制污泥膨胀

污泥膨胀是活性污泥工艺运行中经常遇到的最棘手的问题之一。本实验以人工合成污水为底物,采用序机式活性污泥法（SBR）;研究投加无机混凝剂氯化钙控制污泥膨胀的情况,同时研究丝状菌和菌胶团的变化。研究发现,投加氯化钙后,丝状菌数量明显减少;形成较多大而密实规则的菌胶团,污泥膨胀得到控制。污泥容积指数（SVI）由最初的309.5 mL/g降到67.1 mL/g,污泥沉降性能改善。停止投加氯化钙后又运行了18周期,活性污泥没有发生再次膨胀。投加氯化钙对COD去除率没有明显影响。研究结果表明,投加氯化钙是一种有效的污泥膨胀应急控制措施。     

生物脱氮除磷工艺中的丝状菌

在生物脱氮除磷工艺中,污泥膨胀是运行管理的难题。介绍了生物脱氮除磷工艺中丝状菌的种类和数量的变化,数据表明,生物脱氮除磷工艺中的丝状菌主要是微丝菌,其次是0675型和0914型菌。经分析认为,污泥龄的增加会促进丝状菌长度的明显增长并导致污泥膨胀,生物残渣的浓度是造成长泥龄污泥膨胀的原因之一。厌氧阶段有分解生物残渣的功能,可改善菌胶团菌的微环境,从而抑制丝状菌的过剩生长,控制污泥膨胀。     

NaCl盐度对耐盐活性污泥沉降性能及脱氮的影响

针对海水冲厕工程的实施,采用序批式活性污泥反应器(SBR)处理实际含盐生活污水,考察了盐度对耐盐活性污泥沉降性能及脱氮效能的影响。研究发现,经过长期盐度驯化后的污泥系统也会出现丝状菌污泥膨胀。在经过10 g/L盐度长期驯化的污泥系统中,污泥容积指数(SVI)随着盐度的升高而降低,盐度升高使丝状菌减少,污泥絮体变小变密实。但是,盐度降低时会引发更严重的污泥膨胀,导致污泥流失。对脱氮性能的研究表明,硝化菌的耐盐能力较强。当盐度由10 g/L改变为0、5、15、20 g/L时,氨氮去除率依然可以维持在99%以上。但亚硝酸盐积累率无论是盐度升高或降低时都升高,这表明驯化后污泥中的亚硝酸氧化菌(NOB)对盐度变化的耐受能力比氨氧化菌(AOB)弱,无论盐度升高或降低都会对其产生较大的影响。     

Filamentous scum bacteria in activated sludge plants: detection and identification quality by conventional activated sludge microscopy versus fluorescence in situ hybridization.

Detection of filamentous bacteria morphotypes involved in scum formation in activated sludge wastewater treatment plants by conventional sludge microscopy is often doomed to fail because of morphological and taxonomical variations. The aim of this study is to compare detection, identification, and quantification quality of filamentous "scum bacteria" found by conventional activated sludge microscopy and fluorescence in situ hybridization (FISH). In the case of filamentous Microthrix parvicella and Eikelboom morphotypes 1863 and 1851, conventional activated sludge microscopy and FISH results correspond well. In contrast, conventional activated sludge microscopy overlooks nocardioform actinomycete and type 1863 single cells. On the other hand, FISH underestimates filamentous nocardioform actinomycetes and morphotypes 0041/0675 or 0092 because of insufficient cell wall permeability or because of their taxonomic variability, with a resulting inadequacy of previously published probes. Nostocoida limicola morphotype results are still inconclusive because of low bacteria numbers being available in situ and the enormous taxonomic variability within this group.     

Biodegradation of phthalate esters during the mesophilic anaerobic digestion of sludge

Phthalic acid esters (PAE) are commonly found in the sludge generated in the wastewater treatment plants. Anaerobic digestion followed by land application is a common treatment and disposal practice of sludge. To date, many studies exist on the anaerobic biodegradation rates of PAE, especially of the easily biodegradable ones, whereas the higher molecular weight PAE have reported to be non-biodegradable under methanogenic conditions. Furthermore, there is no information on the effect of the PAE on the performance of the anaerobic digesters treating sludge. In this study, the anaerobic biodegradation of di-n-butyl phthalate (DBP), di-ethyl phthalate (DEP) and di-ethylhexyl phthalate (DEHP) was investigated and their relative rates of anaerobic degradation were calculated. Also, the biological removal of PAE during the anaerobic digestion of sludge in bench-scale digesters was investigated using DBP and DEHP as model compounds of one biodegradable and one recalcitrant PAE respectively. The degradation of all the PAE tested in this study (DEP, DBP and DEHP) is adequately described by first-order kinetics. Batch and continuous experiments showed that DEP and DBP present in sludge are rapidly degraded under mesophilic anaerobic conditions (a first-order kinetic constant of 8.04 x 10(-2) and 13.69 x 10(-2)-4.35 day(-1) respectively) while DEHP is degraded at a rate between one to two orders of magnitude lower (0.35 x 10(-2)-3.59 x 10(-2) day(-1)). It is of high significance that experiments with anaerobic sludge of different origin (US and Europe) showed that degradation of DEHP occurs under methanogenic conditions. Accumulation of high levels of DEHP (more than 60 mg/l) in the anaerobic digester has a negative effect on DBP and DEHP removal rates as well as on the biogas production.     

Effects of chlorination on the adhesion strength and deflocculation of activated sludge flocs.

A side effect of the application of chlorine for controlling filamentous bulking is deflocculation of floc-forming bacteria, which may cause unacceptable effluent deterioration depending on dosing. It was assumed that chlorine may adversely affect the adhesion ability of floc bacteria, promoting their erosion in shear flow. The effect of chlorination on the strength of activated sludge flocs was investigated. The adhesion-erosion (AE) model developed by Mikkelsen and Keiding was used to interpret results from deflocculation tests with varying shear and solids concentration. The AE model yields the adhesion enthalpy (deltaHG/R) of cells in sludge flocs and parameters from the model were used to quantify the sludge in terms of floc strength. Two activated sludges with different initial characteristics were studied. The resulting model parameters showed that the AE model was suitable for quantifying the bond energy of particles to the activated sludge exposed to chlorine. For one activated sludge, adhesion of cells was largely unaffected by the applied chlorine doses. A second sludge showed reduced adhesion strength with chlorine, leading to increasing deflocculation. The simple batch test and AE model proved valuable for assessing the effect of chlorination on the flocs in activated sludge. By use of these procedures, it is possible to determine acceptable chlorine dosing to avoid excessive deflocculation and effluent deterioration.     

ASM No.2d模型模拟SBR工艺同步脱氮除磷效能

SBR工艺由于处理上的高效性和操作上的灵活性在世界范围的污水处理领域得到广泛应用.采用国际水质协会1999年提出的ASM No.2d模型,利用matlab作为程序开发工具编制计算模型,并利用该模型对一实验室规模SBR系统进行模拟.模拟过程中动力学和化学计量参数采用ASM No.2d给出的典型参数值,并结合实际SBR系统进行了修正.结果表明,该模型能够较好模拟SBR工艺同步脱氮除磷效能,说明应用ASM No.2d进行SBR系统的模拟能够对SBR系统的优化和控制起辅助作用.     

Influence of chemical oxygen demand/total Kjeldahl nitrogen ratio and sludge age on nitrification of nitrogenous wastewater.

Four laboratory-scale biological nitrification units (influent total Kjeldahl nitrogen [TKN] = 1002 to 1062 mg/L) were operated at chemical oxygen demand (COD)/TKN ratios of approximately 0.5, 1.0,15, and 2.0 and at three different sludge ages of 30, 20, and 10 days to study the influence of COD/TKN, sludge age, COD loading, and TKN loading on nitrification and nitrifiers. Percent nitrification was found to increase with decreases in COD/TKN and increases in sludge age. The average nitrifier concentration increased from 460 mg/L at a COD/TKN of 2.22 and a sludge age of 10 days to 706 mg/L at a COD/TKN of 0.676 and a sludge age of 30 days. The nitrifier fraction was found to be higher at a lower COD/TKN and lower at a higher COD/TKN. The nitrifier fraction increased with the decrease in sludge age and COD loadings and the increase in TKN loadings. The effect of sludge age on the nitrifier fraction was amplified at a COD/ TKN of approximately 0.5 rather than at approximately 2.0. The nitrification rate (kilograms TKN oxidized per kilograms nitrifiers per day) was shown to be dependent on COD/TKN and sludge age. The activity performed by Nitrobacter was affected at all COD/TKN ratios studied as well as at a sludge age of 10 days. This was manifested by the accumulation of high levels of nitrite-nitrogen in the nitrified effluent. The presence of heterotrophs did not affect nitrification rates and the growth of nitrifiers, which were found to be beneficial. High sludge age and COD loadings resulted in a higher sludge volume index of more than 200 mL/g mixed liquor suspended solids. Microscopic examination showed filamentous structure of sludge under these conditions. It is concluded from the investigations that a sludge age of 30 days and a COD/TKN of approximately 1.0 are optimal to yield maximum nitrification and nitrifier growth rates for treating high-strength nitrogenous wastewater.     

剩余污泥对酸性大红G的吸附

以剩余污泥为吸附剂,研究其对模拟废水中酸性大红G的吸附条件及吸附机理。结果表明,剩余污泥对酸性大红G的吸附是一个快速过程,吸附时间可控制在30 min;其吸附过程同时受液膜扩散和颗粒内扩散的影响,可以用假二级动力学模型进行描述和预测;Freundlich方程可以较好地描述剩余污泥对酸性大红G的吸附行为。污泥未调pH时,对pH<2的溶液中酸性大红G的吸附性能良好;污泥pH为1时,对实验范围(pH<11)溶液中的酸性大红G均可有效吸附;污泥投加量增加,酸性大红G去除率升高,但污泥对酸性大红G的吸附量下降。     

Optimization of enhanced biological phosphorus removal after periods of low loading.

Enhanced biological phosphorus removal is a well-established technology for the treatment of municipal wastewater. However, increased effluent phosphorus concentrations have been reported after periods (days) of low organic loading. The purpose of this study was to evaluate different operating strategies to prevent discharge of effluent after such low-loading periods. Mechanisms leading to these operational problems have been related to the reduction of polyphosphate-accumulating organisms (PAOs) and their storage compounds (polyhydroxy alkanoates [PHA]). Increased effluent phosphorus concentrations can be the result of an imbalance between influent loading and PAOs in the system and an imbalance between phosphorus release and uptake rates. The following operating conditions were tested in their ability to prevent a reduction of PHA and of overall biomass during low organic loading conditions: (a) unchanged operation, (b) reduced aeration time, (c) reduced sludge wastage, and (d) combination of reduced aeration time and reduced sludge wastage. Experiments were performed in a laboratory-scale anaerobic-aerobic sequencing batch reactor, using acetate as the carbon source. Without operational adjustments, phosphorus-release rates decreased during low-loading periods but recovered rapidly. Phosphorus-uptake rates also decreased, and the recovery typically required several days to increase to normal levels. The combination of reduced aeration time and reduced sludge wastage allowed the maintenance of constant levels of both PHA and overall biomass. A mathematical model was used to explain the influence of the tested operating conditions on PAO and PHA concentrations. While experimental results were in general agreement with model predictions, the kinetic expression for phosphorus uptake deviated significantly for the first 24 hours after low-loading conditions. Mechanisms leading to these deviations need to be further investigated.     

Enhanced biological phosphorus removal and recovery

Activated sludge systems designed for enhanced nutrient removal are based on the principle of altering anaerobic and aerobic conditions for growth of microorganisms with a high capacity of phosphorus accumulation. Most often, filamentous bacteria constitute a component of the activated sludge microflora. The filamentous microorganisms are responsible for foam formation and activated sludge bulking. The results obtained confirm unanimously that the filamentous bacteria have the ability of phosphorus uptake and accumulation as polyphosphates. Hydrodynamic disintegration of the foam microorganisms results in the transfer of phosphorus and metal cations and ammonium-nitrogen into the liquid phase. It was demonstrated that the disintegration of foam permits the removal of a portion of the nutrients in the form of struvite.     

Biodegradation of phthalate esters in polluted soil by using organic amendment

This study investigated the biodegradation of the phthalate esters (PAEs) di-n-butyl phthalate (DBP) and di-(2-ethyl hexyl) phthalate (DEHP) in sludge and sludge-amended soil. DBP (100 mg kg(-1)) and DEHP (100 mg kg(-1)) were added to sewage sludge, which was subsequently added to soil. The results showed that sewage sludge can degrade PAEs and the addition of sewage sludge to soil enhanced PAE degradation. Sludge samples were separated into fractions with various particle size ranges, which spanned 0.1-0.45 μm to 500-2000 μm. The sludge fractions with smaller particle sizes demonstrated higher PAE degradation rates. However, when the different sludge fractions were added to soil, particle size had no significant effect on the rate of PAE degradation. The results from this study showed that microbial strains F4 (Rhodococcus sp.) and F8 (Microbacterium sp.) were constantly dominant in the mixtures of soil and sludge.     

Sample storage and extraction efficiencies in determination of polycyclic and nitro musks in sewage sludge

Analytical technology is continuously improving, developing better methods for isolating and concentrating trace compounds in environmental samples. Polycyclic and nitro musks (PNMs) are one group of emerging trace compounds detected in municipal wastewater. Differences in sample storage, preparation, and extraction methods for their measurement have led to variability in results. We analyzed 11 PNMs by GC/MS and compared the results of different storage times and extraction methods (supercritical fluid (SFE) or microwave-assisted (MAE)) for 202 samples of primary sludge, waste activated sludge (WAS), raw sludge, and aerobically/anaerobically digested biosolids collected from Canadian municipal wastewater treatment plants. Sixty-three air-dried samples were extracted by SFE, and 139 air-dried, centrifuged, or filtered samples were extracted by MAE. The mean surrogate recoveries were 89% (standard deviation (SD)=11%) for d(10)-anthracene by SFE and 88% (SD=14%) for d(10)-phenanthrene by MAE. Storage study results showed that PNM concentrations changed by a mean of 7% and 9% for primary sludge and WAS respectively after four weeks and decreased up to 25% after 13.5 months of storage in amber glass containers at -18 degrees C. Air-drying of sludge at room temperature caused losses of about 50% of PNM concentrations compared to centrifugation. The proportions of PNMs present in the liquid phase of sludge samples were less than 5% compared to proportions in the sludge solids. The most complete liquid-solid separation was achieved by filtration of frozen/thawed sludge samples, producing a liquid phase that contained less than 1% of the total musk content of the sample.     

Improved computational model (AQUIFAS) for activated sludge, integrated fixed-film activated sludge, and moving-bed biofilm reactor systems, Part I: Semi-empirical model development

Research was undertaken to develop a model for activated sludge, integrated fixed-film activated sludge (IFAS), and moving-bed biofilm reactor (MBBR) systems. The model can operate with up to 12 cells (reactors) in series, with biofilm media incorporated to one or more cells, except the anaerobic cells. The process configuration can be any combination of anaerobic, anoxic, aerobic, post-anoxic with or without supplemental carbon, and reaeration; it can also include any combination of step feed and recycles, including recycles for mixed liquor, return activated sludge, nitrates, and membrane bioreactors. This paper presents the structure of the model. The model embeds a biofilm model into a multicell activated sludge model. The biofilm flux rates for organics, nutrients, and biomass can be computed by two methods--a semi-empirical model of the biofilm that is relatively simpler, or a diffusional model that is computationally intensive. The values of the kinetic parameters for the model were measured using pilot-scale activated sludge, IFAS, and MBBR systems. For the semiempirical version, a series of Monod equations were developed for chemical oxygen demand, ammonium-nitrogen, and oxidized-nitrogen fluxes to the biofilm. Within the equations, a second Monod expression is used to simulate the effect of changes in biofilm thickness and fraction nitrifiers in the biofilm. The biofilm flux model is then linked to the activated sludge model. The diffusional model and the verification of the models are presented in subsequent papers (Sen and Randall, 2008a, 2008b). The model can be used to quantify the amount of media and surface area required to achieve nitrification, identify the best locations for the media, and optimize the dissolved oxygen levels and nitrate recycle rates. Some of the advanced features include the ability to apply different media types and fill fractions in cells; quantify nitrification, denitrification, and biomass production in the biofilm and mixed liquor suspended solids; and perform dynamic simulations.     

进水水质成分改变引发的污泥粘性膨胀及控制

在研究强化SBR工艺除污性能时，由于可溶性淀粉投加导致进水水质成分发生改变，污泥沉降性能在短时间内迅速恶化，污泥出现大量的粘液。镜检发现，大量指状菌胶团异常增殖且丝状菌的数量也逐渐减少。实验结果表明，系统膨胀属于污泥粘性膨胀。停止可溶性淀粉和提高主反应池的DO浓度，污泥粘性膨胀并未得到恢复，但污泥粘液逐渐消失。粘液消失后，通过模拟前期进水水质成分和缩短泥龄，污泥粘性膨胀得以控制，污泥沉降性能在短时间内恢复。实验还研究了污泥粘性膨胀对污染物去除性能的影响。     

The effect of heavy metals on the activated sludge process and its microbial community analysis using 16S ribosomal DNA

The effect of heavy metal shock loading on biological treatment systems was studied by traditional methods and molecular biological techniques. Two kinds of SBR (sequence batch reactor) operation units, unacclimated and acclimated activated sludge systems, were studied. The addition of special nutrients and powdered activated carbon (PAC) to stimulate heavy metal uptake and recovery were studied. The kinetic constants could be used to describe the effect of the inhibition of substance utilisation. The results showed that heavy metal shock loading had a greater effect on the unacclimated activated sludge system than on the acclimated one. The special nutrients greatly enhanced the uptake of copper, and the PAC improved sludge settling and decreased the turbidity of the effluent. The variation of dominant species and the diversity of the bacterial community were analysed using 16S ribosomal DNA. Compared with the slight change of dominant species during acclimation by copper, there was a great change in the acclimated system shocked by a high concentration of copper. The results confirmed that the acclimation could improve the resistance of microorganisms to heavy metal toxicity.     

Biodegradation of phthalate esters in polluted soil by using organic amendment

This study investigated the biodegradation of the phthalate esters (PAEs) di-n-butyl phthalate (DBP) and di-(2-ethyl hexyl) phthalate (DEHP) in sludge and sludge-amended soil. DBP (100 mg kg^?1) and DEHP (100 mg kg^?1) were added to sewage sludge, which was subsequently added to soil. The results showed that sewage sludge can degrade PAEs and the addition of sewage sludge to soil enhanced PAE degradation. Sludge samples were separated into fractions with various particle size ranges, which spanned 0.1–0.45 μm to 500–2000 μm. The sludge fractions with smaller particle sizes demonstrated higher PAE degradation rates. However, when the different sludge fractions were added to soil, particle size had no significant effect on the rate of PAE degradation. The results from this study showed that microbial strains F4 (Rhodococcus sp.) and F8 (Microbacterium sp.) were constantly dominant in the mixtures of soil and sludge.     

Identifying different types of bulking in an activated sludge system through quantitative image analysis

The present study proposes an image analysis methodology for the identification of different types of disturbances in wastewater treatment activated sludge systems. Up to date, most reported image analysis methodologies have been used in activated sludge processes with the aim of filamentous bulking detection, however, other disturbances could be foreseen in wastewater treatment plants. Such disturbances can lead to fluctuations in the biomass contents, affecting the mixed liquor suspended solids (MLSS), and in the sludge settling ability, affecting the sludge volume index (SVI). Therefore, this work focuses on predicting the MLSS and SVI parameters for different types of disturbances affecting an activated sludge system. Four experiments were conducted simulating filamentous bulking, zoogleal or viscous bulking, pinpoint floc formation, and normal operating conditions. Alongside the MLSS and SVI determination, the aggregated and filamentous biomass contents and morphology were studied as well as the biomass Gram and viability status, by means of image analysis.     

Measurement of symbiotic nitrogen-fixation in leguminous host-plants grown in heavy metal-contaminated soils amended with sewage sludge

Rates of nitrogen fixation by Rhizobium in symbiosis with leguminous host-plants including white clover, broad bean and peas have been established in soils that have been amended experimentally with heavy metal-contaminated sewage sludges. Results from 15N-dilution experiments for the measurement of N2 fixation have shown that adverse heavy metal effects are apparent on symbiotic N2 fixation rates for white clover grown in inter-specific competition with ryegrass under mixed sward conditions, compared to white clover grown in pure sward. Further experiments on broad bean and pea indicated a significant, but minor-inhibitory metal-related effect on the rate of N2 fixation compared to untreated soils and soils amended with a relatively uncontaminated sludge. The implications of the results with respect to sludge utilisation in agriculture are discussed.