Comparison of PCE and TCE disappearance in heated volatile organic analysis vials and flame-sealed ampules

The rates of hydrolysis reported for tetrachloroethylene (PCE) and trichloroethylene (TCE) at elevated temperatures range over two orders-of-magnitude, where some of the variability may be due to the presence of a gas phase. Recent studies suggest that volatile organic analysis (VOA) vials provide a low-cost and readily available zero headspace system for measuring aqueous-phase hydrolysis rates. This work involved measuring rates of PCE and TCE disappearance and the corresponding appearance of dechlorination products in water-filled VOA vials and flame-sealed ampules incubated at 21 and 55 °C for up to 95.5 days. While PCE and TCE concentrations readily decreased in the VOA vials to yield first-order half lives of 11.2 days for PCE and 21.1 days for TCE at 55 °C, concentrations of anticipated dechlorination products, including chloride, remained constant or were not detected. The rate of PCE disappearance was 34 times faster in VOA vials at 55 °C compared to values obtained with flame-sealed ampules containing PCE-contaminated water. In addition, the concentration of TCE increased slightly in flame-sealed ampules incubated at 55 °C, while a decrease in TCE levels was observed in the VOA vials. The observed losses of PCE and TCE in the VOA vials were attributed to diffusion and sorption in the septa, rather than to dechlorination. These findings demonstrate that VOA vials are not suitable for measuring rates of volatile organic compound hydrolysis at elevated temperatures.     

Photocatalytic activity of the calcined H-titanate nanowires for photocatalytic oxidation of acetone in air

Hydrogen titanate (H-titanate) nanowires were prepared via a hydrothermal reaction of TiO₂ powders (P25) in KOH solutions and then calcined at various temperatures. The phase structure, crystallite size, morphology, specific surface area, and pore structures of the calcined H-titanate nanowires at various temperatures were characterized with field emission scanning electron microscope, X-ray diffraction, transmission electron microscopy and nitrogen adsorption–desorption isotherms, and their photocatalytic activities were evaluated by photocatalytic oxidation of acetone in air. With increasing calcination temperature, the specific surface area and porosity of the calcined samples steadily decreased. At a calcination temperature range of 400–600 °C, the calcined H-titanate nanowires showed higher photocatalytic activity than P25 powders for photocatalytic oxidation of acetone. Especially, at 500 °C, the calcined H-titanate nanowires showed the highest photocatalytic activity, which exceeded that of P25 by a factor of about 1.8 times. This can be attributed to the synergetic effect of larger specific surface area, higher pore volume and the presence of brookite TiO₂. With further increase in the calcination temperature (700–900 °C), the photocatalytic activity of the samples decreased obviously owing to the growth of TiO₂ crystallites.     

PCDDs & PCDFs from the MSW incinerator

In the range 670 to 900°C furnace temperature, dioxin concentrations strongly depended upon the oxygen concentration in the flue gas. In keeping the oxygen concentration at apploximately 12 percent, dioxin was reduced in the flue gas. For further dioxin reduction from the flue gas, it was the most effective process to treat the flue gas with bag filter system with 120 C operation.     

Kinetics of carbon degradation and PCDD/PCDF formation on MSWI fly ash

The native carbon oxidation and PolyChloroDibenzo-p-Dioxins and PolyChloroDibenzoFurans, PCDD/F, formation were simultaneously studied at different temperatures (230-350 degrees C) and times (0-1440 min) in order to establish a direct correlation between the disappearance of the reagent and the formation of the products. The kinetic runs were conducted in an experimental set up where conditions were chosen to gain information on the role of fly ash deposits in cold zones of municipal solid waste incinerators in PCDD/F formation reaction. The carbon oxidation measured as the decrease of total organic carbon of fly ash was in agreement with the carbon evolved as sum of CO and CO(2). The carbon mass balance indicated an increase in the efficiency of carbon conversion in CO and CO(2) with temperature. The CO and CO(2) formation was the result of two parallel pseudo first order reactions thus giving significant information about the reaction mechanism. PCDD/F formation as a function of temperature showed that the maximum formation was achieved in a narrow range around 280 degrees C; the time effect at 280 degrees C was a progressive formation increase at least up to 900 min. The PCDF:PCDD molar ratio increased with temperature and time, and the most abundant homologues were HxCDD, HpCDD, OCDD for PCDD, and HxCDF, HpCDF within PCDF. These experimental results supported the hypothesis that the formation mechanism was the de novo synthesis.     

A microcosm approach to assessing the effects of earthworm inoculation and oat cover cropping on CO2 fluxes and biological properties in an amended semiarid soil

We designed a microcosm experiment to assess the influence of inoculation with Eisenia foetida earthworms and the establishment of an Avena sativa cover crop on biological (enzyme activities and labile carbon fractions) soil quality indicators in a soil treated with a composted organic residue, and to determine the contribution of these treatments to carbon dioxide emissions from the soil to the atmosphere of the microcosm. The microcosms were incubated for 53 days under 28 °C/18 °C day/night temperatures. The addition of earthworms and the planting of A. sativa increased dehydrogenase activity of compost amended soil by about 44% after 23 days of incubation. The metabolic potential, calculated as the ratio dehydrogenase activity/water soluble C, was higher in the compost amended soil planted with A. sativa. The highest total amount of CO₂–C evolved occurred in the soil treated with composted residue and earthworms (about 40% of the total amount of CO₂ evolved came from earthworm activity). The planting of A. sativa increased the decomposition rate constant of organic matter in the amended soil but decreased the potentially mineralizable C pool. In conclusion, the establishment of an A. sativa cover crop and the addition of E. foetida to a degraded agricultural soil treated with composted residue were effective treatments for improving the biological and biochemical quality and the metabolic potential of the soil.     

Vapour pressures, aqueous solubility, Henry's law constants and air/water partition coefficients of 1,8-dichlorooctane and 1,8-dibromooctane

New data on the vapour pressures and aqueous solubility of 1,8-dichlorooctane and 1,8-dibromooctane are reported as a function of temperature between 20 °C and 80 °C and 1 °C and 40 °C, respectively. For the vapour pressures, a static method was used during the measurements which have an estimated uncertainty between 3% and 5%. The aqueous solubilities were determined using a dynamic saturation column method and the values are accurate to within ±10%. 1,8-Dichlorooctane is more volatile than 1,8-dibromooctane in the temperature range covered (p_sat varies from 3 to 250 Pa and from 0.53 to 62 Pa, respectively) and is also approximately three times more soluble in water (mole fraction solubilities at 25 °C of 5.95 × 10⁻⁷ and 1.92 × 10⁻⁷, respectively). A combination of the two sets of data allowed the calculation of the Henry’s law constants and the air water partition coefficients. A simple group contribution concept was used to rationalize the data obtained.     

Emission of organic compounds by combustion of waste plastics involving vinyl chloride polymer

Organic compounds emitted from combustion of waste plastics involving vinyl chloride polymer were investigated in an actual waste incinerator. The amounts of volatile aliphatic hydrocarbons and volatile chlorinated organic compounds decreased when the secondary combustion temperature was controlled over 900°C. On the other hand, the amounts of some aromatic hydrocarbons increased with a rise of the secondary combustion temperature.     

On the performance of Fe and Fe,F doped Ti-Pt/PbO2 electrodes in the electrooxidation of the Blue Reactive 19 dye in simulated textile wastewater

The electrochemical performance of pure Ti–Pt/β-PbO₂ electrodes, or doped with Fe and F (together or separately), in the oxidation of simulated wastewaters containing the Blue Reactive 19 dye (BR-19), using a filter-press reactor, was investigated and then compared with that of a boron-doped diamond electrode supported on a niobium substrate (Nb/BDD). The electrooxidation of the dye simulated wastewater (volume of 0.1 l, with a BR-19 initial concentration of 25 mg l⁻¹) was carried out under the following conditions: current density of 50 mA cm⁻², volume flow rate of 2.4 l h⁻¹, temperature of 25 °C and electrode area of 5 cm². The performances of the electrodes in the dye decolorization were quite similar, achieving 100% decolorization, and in some cases 90% decolorization was achieved by applying only ca. 0.3 A h l⁻¹ (8 min of electrolysis). The reduction of the simulated wastewater organic load, monitored by its total organic carbon content (TOC), was greater for the Ti–Pt/β-PbO₂–Fe,F electrode obtained from an electrodeposition bath containing 1 mM Fe³⁺ and 30 mM F⁻. In this case, after 2 h of electrolysis the obtained TOC reduction was 95%, while for the pure β-PbO₂ and the Nb/BDD electrodes the reductions were 84% and 82%, respectively.     

Removal of carbon disulfide via coupled reactions on a bi-functional catalyst: experimental and modeling results

A mathematical model describing the rate of carbon disulfide (CS₂) removal due to coupled reactions has been developed. Kinetic studies were carried out in a fixed bed reactor under atmospheric pressure and a range of temperatures (85–125 °C). The effects of flow rate, CS₂ inlet concentration, temperature and relative humidity were analyzed. A kinetic model based on axial dispersion, external and internal mass-transfer resistances, as well as effects of S deposition on the inner-face of the catalyst was in agreement with the CS₂ experimental breakthrough curves. The mathematical model can be used for process design and scale up of similar systems.     

Determination and distribution characteristics of degradation products of nonylphenol polyethoxylates in the rivers of Taiwan

Concentrations of degradation products of nonylphenol polyethoxylates (NPEOs) were analyzed in river water samples in order to determine the distribution characteristic of these alkylphenolic compounds in 18 major rivers of Taiwan. The degradation products of NPEOs were detected in all river samples, with the dicarboxylates alkylphenolic degradation products (CAPEC) being detected most frequently and at the highest concentrations. Concentrations of NP and NP1EO in rivers ranged from n.d. to 5.1 μg l⁻¹ and n.d. to 0.5 μg l⁻¹, respectively. The total concentrations of shortened carboxylates (i.e., NP1EC + NP2EC + NP3EC) and dicarboxylates alkylphenolic degradation products (CAP1EC + CAP2EC) ranged from n.d. to 63.6 μg l⁻¹ and n.d. to 94.6 μg l⁻¹, respectively. Concentrations of NP2EC, NP3EC and all CAPEC residues were determined semi-quantitatively by comparing with the internal standard. Significantly higher concentrations of CAPEC residues were detected in the river waters as compared to those of NP, NP1EO and NPEC degradation products and the average proportions of these compounds in the samples of the rivers were as follows: NP + NP1EO was 5 ± 2.5%, total NPEC was 25 ± 12%, and total CAPEC was 70 ± 12%. The high concentration ratios of CAPEC/NPEC illustrate that aerobic biodegradation plays a main route in the fate of NPEO in the rivers of Taiwan.     

Effects of copper chloride on formation of polychlorinated dibenzo-p-dioxins in model waste incineration

Combustion experiments in a laboratory-scale fluidized-bed reactor were conducted to elucidate the effects of copper chloride as a catalyst on polychlorinated dibenzo-p-dioxins (PCDDs) formation in municipal waste incineration. We used model wastes with and without copper chloride (CuCl₂ · 2H₂O), both of which contained polyvinyl chloride as a chlorine source. Combustion temperature was set to 900 °C, and the amount of air supplied was twice the stoichiometric ratio. The experimental setup was carefully planned to suppress the influences of experimental conditions except the waste composition. Results of these experiments showed that copper chloride in the waste increased the amount of PCDDs formed and made the homologue profile to shift towards the highly chlorinated species. Copper chloride contributes to the PCDDs formation by promoting chlorination, whereby the reaction is important in that organic matter is chlorinated directly by copper compounds. Copper chloride did not exert a great influence on the isomer distribution patterns of PCDDs, while there appeared a significant difference in the case of PCDFs. This points out the difference of the major formation mechanisms between PCDDs and PCDFs. PCDDs are less formed by the catalytic reactions from carbon/polycyclic aromatic hydrocarbons than PCDFs in our experimental conditions.     

PBDF and PBDD from the combustion of bromine containing flame retarded polymers: A survey

The formation of polybrominated dibenzofurans (PBDF) and dibenzodioxins (PBDD) during the pyrolysis of different polymers containing brominated organic flame retardants was investigated. The pyrolyses were conducted at two different temperatures (600°C and 800°C) using three different oven configurations. Both the pyrolysis gases and the solid residues were analysed for PBDF and PBDD.

PBDF were found in almost all samples, but both the concentration and the degree of bromination varied greatly. The largest yields of PBDF in the percent range were measured in the pyrolysis products of polymers containing brominated diphenyl ethers. The other flame retardants generally yielded only a few ppm of PBDF. PBDD are formed only in a few samples and related to the PBDF in very low concentrations.     

Investigation on the adsorption capability of egg shell membrane towards model textile dyes

Adsorption isotherms of Direct Red 80 (DR80) and Acid Blue 25 (AB25) on the egg shell membrane (ESM) were performed at 20 ± 1 °C. Physical characteristics of ESM such as surface area and presence of functional groups were verified. The Fourier transform infra-red (FTIR) spectra proved the presence of fuctional groups such as hydroxyl, amine and carbonyl groups in ESM. The surface area of ESM was found to be 2.2098 m²/g. The effects of operational parameters such as initial dye concentration, pH₀, contact time, particle size and ESM doses were studied. The Langmuir, Freundlich, BET, Redlich-Peterson and Temkin adsorption models were applied to describe the equilibrium isotherms. The pseudo-first-order and pseudo-second-order kinetics models were examined to evaluate the kinetics data at different pH₀ values (2–12) and the rate constants were calculated. Maximum desorption of 81.8% was achieved for both dyes in aqueous solution at pH₀ 12. Also scanning electron micrographs (SEM) of the treated and untreated adsorbent were performed. Results indicate that ESM could be employed as a natural and Eco-Friendly adsorbent material for the removal of trace organics in solutions.     

Multivariate curve resolution of multidimensional excitation-emission quenching matrices of a Laurentian soil fulvic acid

Fluorescence excitation–emission matrices (EEM) of aqueous solutions of Laurentian soil fulvic acid (LFA) at three concentrations (50, 75 and 100 mg/l) were obtained at two pH values (pH = 4.0 and 6.0) and as function of the Cu(II) ion concentration. The presence of Cu(II) ion provokes quenching of the intrinsic LFA fluorescence due to complex formation. Multivariate curve resolution (MCR-ALS) was used to successfully decompose single EEM into excitation and emission spectra for the detected components. Moreover, multidimensional (up to six dimensions) data matrices were generated by adding EEM collected as function of the LFA and Cu(II) concentrations and pH. MCR-ALS was able to resolve the excitation and emission spectra from these multidimensional data matrices given further information about the spectral variation profiles induced by the experimental factors. Conditional stability constants (log K_LFACu) were calculated from the quenching profiles observed as function of the Cu(II) concentration, as well as, their trends as function of pH and LFA concentration were obtained – average (and standard deviation) of log K_LFACu = 4.6 ± 0.2. This EEM/MCR-ALS methodology constitutes a new tool for the study of natural organic matter under varying experimental conditions that characterize natural environmental systems.     

Microbial reduction of nitrate in the presence of nanoscale zero-valent iron

Microbial reduction of nitrate in the presence of nanoscale zero-valent iron (NZVI) was evaluated to assess the feasibility of employing NZVI in the biological nitrate treatment. Nitrate was completely reduced within 3 d in a nanoscale Fe(0)-cell reactor, while only 50% of the nitrate was abiotically reduced over 7 d at 25 °C. The removal rate of nitrate in the integrated NZVI-cell system was unaffected by the presence of high amounts of sulfate. Efficient removal of nitrate by Fe(II)-supported anaerobic culture in 14 d indicated that Fe(II), which is produced during anaerobic iron corrosion in the Fe(0)-cell system, might act as an electron donor for nitrate. Unlike abiotic reduction, microbial reduction of nitrate was not significantly affected by low temperature conditions. This study demonstrated the potential applicability of employing NZVI iron as a source of electrons for biological nitrate reduction. Use of NZVI for microbial nitrate reduction can obviate the disadvantages associated with traditional biological denitrification, that relies on the use of organic substrates or explosive hydrogen gas, and maintain the advantages offered by nano-particle technology such as higher surface reactivity and functionality in suspensions.     

The influence of storage on the morphology and physiology of phthalic acid-degrading aerobic granules

The precultured aerobic granules with special degradabilities could be used as a feasible bioseed for enhancement of aerobic granulation systems. In practice, the storage stability, physicochemical characteristics, and recovering efficiency of granules are crucial for a long-distance transportation and successful application. In this study, phthalic acid (PA)-degrading aerobic granules were cultivated and stored for 8 wk at 4 °C. The granular size, settling ability as well as structure integrity was found stable during the storage period. It was observed that the upper 1/3 part of granules stored in the reagent bottle turned to black color, while the lower 2/3 part granules did not significantly change color (brown–yellow) after the 8-wk storage. The black and brown–yellow color PA-degrading granules were manually separated and re-inoculated into two identical sequencing batch reactors for reviving the PA degradation capability. After a 7 d operation, both black and yellow granules restored their activities to the levels before storage, in terms of total organic carbon removal efficiency (100%), specific oxygen uptake rate (59 mg g VSS⁻¹ h⁻¹), and adenosine triphosphate content (0.016 mg g VSS⁻¹). This study demonstrated that aerobic granules grown on a complex substrate could tolerate storage conditions and rapidly restored their bioactivities toward the target pollutant. The results also shed the light on the future application of precultured aerobic granules with unique functions for biodegradation and bioremediation purpose.     

Titania-supported silver-based bimetallic nanoparticles as photocatalysts

Photocatalytic process has shown recently a great potential as an environmental friendly and clean remediation technology for organic pollutants in wastewater. This work described the synthesis of silver-based bimetallic nanoparticles using colloid chemistry and the subsequent immobilization onto titania to form composite photocatalytic materials (titania-supported Ag–Pt nanoparticles). The photocatalysts were characterized by X-ray diffraction, electron microscopy, and nitrogen physisorption. The catalytic activity of the photocatalysts was evaluated by photocatalytic degradation of phenol and 2-chlorophenol (2-CP) in synthetic wastewater solutions. The photocatalytic processes were conducted in a batch photoreactor containing appropriate solutions of phenol and 2-CP with UV irradiation of 450 W. UV-visible spectrophotometer was used for analyzing the concentration of phenol and 2-CP in solutions. Parameters affecting the photocatalytic process such as the solution pH, phenol and 2-CP concentrations, and catalyst concentration were investigated. The results obtained revealed that TiO₂-supported Ag/Pt nanoparticles showed a higher activity for UV-photocatalytic degradation of both phenol and 2-CP pollutants in the solution (as compared to the plain rutile TiO₂). The photodegradation processes were optimized by the 0.5-g/L catalyst with a pollutant concentration of 50 mg/L for all the samples. Complete degradation for both phenol and 2-CP was achieved after 120 min.     

Sorption of organic compounds to activated carbons. Evaluation of isotherm models

Sorption to ‘hard carbon’ (black carbon, coal, kerogen) in soils and sediments is of major importance for risk assessment of organic pollutants. We argue that activated carbon (AC) may be considered a model sorbent for hard carbon. Here, we evaluate six sorption models on a literature dataset for sorption of 12 compounds onto 12 ACs and one charcoal, at different temperatures (79 isotherms in total). A statistical analysis, accounting for differences in the number of fitting parameters, demonstrates that the dual Langmuir equation is in general superior and/or preferable to the single and triple Langmuir equation, the Freundlich equation, a Polanyi–Dubinin–Manes equation, and the Toth equation. Consequently, the analysis suggests the presence of two types of adsorption sites: a high-energy (HE) type of site and a low-energy (LE) type of site. Maximum adsorption capacities for the HE domain decreased with temperature while those for the LE domain increased. Average Gibbs free energies for adsorption from the hypothetical pure liquid state at 298 K were fairly constant at −15 ± 4 and −5 ± 4 kJ mol⁻¹ for the HE and LE domain, respectively.     

Determination of dithiocarbamate fungicide propineb and its main metabolite propylenethiourea in airborne samples

A simple, rapid and sensitive GC–MS method for the determination of dithiocarbamate fungicide propineb [polymeric zinc propylenebis (dithiocarbamate)] and an improved HPLC procedure for the simultaneous determination of its main metabolite, propylenethiourea, and ethylenethiourea, the main metabolite of all ethylenedithiocarbamates, in airborne samples are described. The method for the analysis of propineb involves the evolution of carbon disulfide (CS₂), under acidic conditions in the presence of stannous chloride, extraction of the generated CS₂ into a layer of isooctane which is then analyzed for CS₂ content by GC–MS in SIM mode. Under the optimum conditions, the retention time of CS₂ was 1.89 min and the total time of chromatographic analysis was 5 min. Recoveries from spiking glass microfibre filters (GF/A) and silica gel filters were 86 ± 7 (n = 9) and 89 ± 4 (n = 9), respectively. The limit of detection is 0.7 ng per filter, which is equivalent to about 0.8–1.0 ng m⁻³ in air. In parallel, an HPLC method with ultraviolet detection is presented for the simultaneous analysis of the metabolites. Separation of the two metabolites was attained in less than 5 min. Recoveries from spiking GF/A and silica gel filters for ethylenethiourea were 100 ± 1 (n = 3) and 98 ± 2 (n = 3), respectively, while for propylenethiourea were 102 ± 1 (n = 3) and 98 ± 1 (n = 3), respectively. The detection limits are about 36–43 and 40–49 ng m⁻³ in air for ethylenethiourea and propylenethiourea, respectively. All the analytes spiked in the filters are proven to be stable for more than one month, at −4 °C.     

Thermal and spectroscopic studies on sorption of nickel(II) ion on protonated baker's yeast

Protonated form (Hy) of yeast was subjected to thermal analysis (TGA and DTG) in the temperature range 60–800 °C. Chemically bound water volatilizes around 200 °C and the matrix undergoes extensive oxidative decomposition at 450 °C, the weight loss reaching 75% at 800 °C. The sorption capacity of the matrix for nickel(II) ion increases on heat treatment from 60 to 200 °C (from 16.9 to 25.0 mg/g), but was reduced on heating to higher temperatures at an initial nickel(II) ion concentration of 1200 mg/g. The FTIR spectra of Hy and nickel(II) ion saturated yeast, indicated that biosorption occurs on the sugar and nucleic acid regions, possibly involving –COOH and –NH groups.