城市生活垃圾土的强度机理及复合幂、指数应力-应变模型

根据垃圾土的大中型三轴压缩实验结果,分析了垃圾土的抗剪强度机理。垃圾土的抗剪强度是由剪切带上各成分间的摩擦和纤维加筋相产生的拉力共同提供,剪切变形初期主要以摩擦为主,随着变形的增加纤维加筋相产生的拉力所发挥的作用逐渐增强。基于三轴压缩实验结果,建立了垃圾土的复合幂、指数应力-应变模型,该模型参数少且具有明确的物理意义,即可反映应变较小和应变较大时的非线性特性,也可反映应变较大时垃圾土明显的加工硬化特性,特别是应力-应变关系曲线增长性向上翘的特征。与实验结果相比,该模型的相关系数均达到0.98以上。     

生活垃圾分选线上柔性破袋机的原理与设计

通过设计高速柔性破袋机并在垃圾分选生产线上进行实验,系统探索了整机构造、鞭具、转辊以及安装位置等重要因素对破袋效果和稳定性的影响,得出了最优鞭型为直径?3~6 mm的钢丝绳,在鞭具根部固定方式保持不小于30°的环向自由度时,可消除疲劳,鞭具最优线速度为10~20 m·s~(-1)。柔性破袋机结构轻简、能耗低,其破袋效果可满足生活垃圾分选线的要求。在防缠方面,相对于鞭具静止的辊子壁面防缠效果更明显。柔性破袋机可以骑跨在输送设备上,在分选线上多点布置,达到破袋率累积的效果。柔性破袋机布置在水平料流面上方时,要比布置在直立料流面一侧防缠效果更好。     

新型堆肥装置设计及其应用研究

根据城市生活垃圾的特点和性质,利用物料平衡和热力学原理进行好氧堆肥实验装置的设计,并对堆肥发酵仓容积的确定和配套辅助设备进行了研究,得出当堆肥装置直径小于225m时,需采取保温措施。通过强制通风静态仓式堆肥小试实验进行的城市生活垃圾堆肥结果表明,通过30℃及以上的水浴加热,可实现固体废物的堆肥化。     

锑污染垃圾腐殖土淋洗修复及其资源化用作绿化用土研究

随着垃圾填埋场开挖筛分分质利用工程的陆续开展,筛分出的腐殖土妥善处置成了亟待解决的问题。通过超声淋洗不同粒径的锑污染垃圾腐殖土,研究了柠檬酸、乙二胺四乙酸二钠(EDTA)及两者复合淋洗剂的淋洗效果,并通过小麦种子萌发实验探究锑污染垃圾腐殖土资源化用作绿化用土的潜力。研究发现,柠檬酸和EDTA复合超声淋洗既可有效提升腐殖土中锑的去除效果,能缩短处理时间,能消除粒径的影响,而且还可以减少营养物质流失。小麦种子萌发实验表明,柠檬酸和EDTA复合超声淋洗后的腐殖土具有资源化用作绿化用土的潜力,适当地可以根据不同营养元素损失率进行氮肥、磷肥和钾肥掺拌。     

新型堆肥装置设计及其应用研究

根据城市生活垃圾的特点和性质，利用物料平衡和热力学原理进行好氧堆肥实验装置的设计，并对堆肥发酵仓容积的确定和配套辅助设备进行了研究，得出当堆肥装置直径小于2．25m时，需采取保温措施。通过强制通风静态仓式堆肥小试实验进行的城市生活垃圾堆肥结果表明，通过30℃及以上的水浴加热，可实现固体废物的堆肥化。     

填埋场不同深度垃圾土压缩性的室内试验研究

阐述了垃圾土的压缩机理,归纳了国内外垃圾土压缩性指标的研究成果。根据某填埋场3个不同深度的垃圾土试样,在改装后的高压固结仪上进行压缩试验,得到垃圾土的压缩系数a、主压缩指数C、修正主压缩指数C'、压缩模量E以及体积压缩系数m,并对试验结果进行分析。试验结果表明,垃圾土的初始孔隙比随填埋深度的增加而减小,垃圾土的压缩指数随其可降解度和有机质含量的减少而降低,垃圾土具有高压缩性,其压缩性指标与垃圾的组成和填埋深度有关。将得到的压缩性指标与国内外的资料进行了比较,可为填埋场的设计及变形计算提供参考。     

垃圾填埋场污泥坑原位修复工程实践

垃圾填埋场内污泥坑的存在严重影响填埋场竖向扩建和填埋堆高。对某垃圾填埋场内污泥坑进行现场勘察取样、原位测试与室内实验,获得污泥的分层及沿深度变化的物理、力学特性,并针对不同分层的污泥,提出表层垃圾清除、污水抽排、泥水混合污泥土工管袋脱水、流塑、软塑污泥原位固化综合处理方法。对污泥坑抽排污水过程中垃圾堆体边坡进行渗流稳定分析,发现渗滤液水位快速下降将导致污泥坑垃圾边坡滑移失稳,在污泥坑治理过程中应采取相应措施。根据污泥坑上覆80~120 m垃圾堆体沿原位固化污泥滑移稳定分析,获得污泥坑原位固化处理强度指标,不排水抗剪强度Cu为40 k Pa。     

城市固体废弃物持水率的室内实验研究

垃圾土持水率是估算填埋场淋沥液高度和分析填埋体稳定性的重要参数。通过对高压固结仪的改造,研制垃圾土持水率的室内实验仪器,并在该仪器上对取自我国南方某填埋场3个不同深度的大直径垃圾土试样进行各级荷载下的持水率实验。研究结果表明,随填埋深度增大,垃圾年份增加,垃圾土可降解度降低,腐殖质含量增大,垃圾土的持水率减小;随上覆压力增大,干重和湿重持水率减小,当上覆压力增大到一定程度,减小趋势变缓;随上覆压力的增大,体积持水率一般呈减小的趋势,但对于疏松垃圾土,在较小的压力下,体积持水率有增大的趋势,当压力增大到一定程度,则随压力的增大而减小;随干密度的增大,垃圾土干重和湿重持水率均减小。提出的垃圾土持水率的室内实验方法和研制的仪器合理可行。     

有机改性成都粘土预处理垃圾渗滤液

以成都粘土为原料,十六烷基三甲基溴化铵(HDTMA)为改性剂制备有机改性土,并将其应用于垃圾渗滤液的预处理。采用单因素静态吸附实验,以粘土对垃圾渗滤液COD和氨氮的去除率作为考查指标,初步探究有机改性土预处理垃圾渗滤液的适宜条件;并对有机改性粘土及原土进行性能表征,初步分析其吸附机理。研究结果表明,有机土的处理效果明显优于原土,处理效果上比原土提高了1.6~2.3倍;有机土预处理垃圾渗滤液适宜条件为:投加量120 g/L、搅拌速度200 r/min、搅拌时间50 min、pH=7、静置时间为6 h。     

矿化垃圾混配种植介质的盆栽实验研究

矿化垃圾营养成分和有机质含量较高,但含有重金属和盐分.为了解矿化垃圾的施加比例对植物的生长影响以及植物对矿化垃圾混配种植介质中营养成分的吸收和重金属的富集,将矿化垃圾和本地绿化土按照不同比例混配,研究混配种植介质的理化性质的改善条件、矿化垃圾对植物体内的生物量和叶绿素含量的影响、植物对混配种植介质中营养成分的吸收量以及植物体内各种重金属累积浓度,探索矿化垃圾的最佳施用比例.实验结果表明,矿化垃圾可改善上海本地土壤贫瘠的普遍状况,其添加质量分数在50%～75%合适,对植物生长有利.     

A survey of municipal solid waste landfills in Beijing during 2009–2011

The investigation of municipal solid waste (MSW) treatment in China is rare due to its sensitivity and difficulty in terms of access. We chose Beijing, the capital of China, as an example to identify the characteristics of MSW landfill treatments using a 2-month investigation with 20 participants. MSW landfill treatments account for nearly 70% of the annual MSW disposal in Beijing; the landfill processes are equipped with many kinds of technologies and consume a large amount of energy and produce a variety of contaminants. The cover method (the most obvious difference in landfill tamping) mainly includes high-density polyethylene (HDPE) geomembranes with loess and soil alone (i.e., loess or sandy soil). We investigated the actual conditions of landfills and collected data on leachate and landfill gas (LFG) emissions and energy consumption during 2009–2011. The results indicated that the cover method employed by landfills was related to treatment quantity, operation, and especially landfill location. Early large-scale landfills located in plains were covered with HDPE geomembranes, and newly built landfills covered with soil tended to be equipped with HDPE covers. Using HDPE cover also contributed greatly to LFG production due to its impermeability but had no remarkable effect on leachate yield reduction due to the dry climate in Beijing. The potential was reinforced by the potentials of decrement and reuse. The disposal method of LFG can be optimized, and the power generated by the LFG process can meet the landfill demand. The gray water recycled from the leachate could be used in the landfill process.

     

城市生活垃圾卫生填埋场恶臭的防治技术进展

恶臭污染已成为垃圾处理和处置过程中的严重公害。在分析中,介绍了填埋场各区域恶臭的控制措施,综述了卫生填埋场恶臭的常规防治技术,重点讨论了生物技术在填埋场脱臭中的应用,这些防治技术对各类环境卫生设施,如垃圾收集站、中转站、焚烧场、堆肥厂及粪便处理厂的臭气治理均有借鉴意义。     

Compressibility of municipal solid waste codisposed with fly ash

If a municipal solid waste (MSW) landfill is used as the foundation for a construction site, the change in the loading conditions may cause considerable compression of the landfill. Therefore, reinforcement to compensate for the loose compression nature of a MSW landfill is a very important design factor for geotechnical engineers when considering the end-use of the landfill. In this study, we discuss a possible technique for stabilizing MSW landfills through the codisposal of municipal solid waste and fly ash. To estimate the stabilization based on the compression characteristics of the codisposed landfill, we performed tests using a large compression set and experimental cells. According to the test results, if the proportion of fly ash is increased, initial and long-term compression could be reduced.     

垃圾填埋场加速稳定化表征指标的相关性分析

加速稳定化表征指标是生物反应器填埋技术评价的重要内容。通过垃圾填埋室内模拟实验,研究不同运行工况下垃圾挥发性固体(VS)、生物可降解物(BDM)、纤维素(C)和纤维素/木质素(C/L)等组分指标的动态变化规律及其对加速稳定化进程的指示作用,进而探寻各指标之间的相关性,进一步筛选确定垃圾填埋场加速稳定化进程的核心表征指标。结果表明,垃圾组分VS、BDM、C和C/L的衰减符合一级反应动力学,其动态变化能够较为灵敏地指示渗滤液回灌和通风供氧对垃圾稳定化的显著加速作用,可作为垃圾填埋场加速稳定化进程的表征指标。VS、BDM、C和C/L相互之间具有良好的正线性相关性。BDM和C/L适宜作为垃圾填埋场加速稳定化进程的核心表征指标。     

城市生活垃圾半好氧生物反应器填埋技术试验研究

对城市生活垃圾半好氧生物反应器填埋技术与传统垃圾填埋技术进行了对比试验,由试验结果可知,半好氧生物反应器填埋技术可缩短填埋垃圾产酸时间,净化渗滤液,加速填埋垃圾稳定化进程.城市生活垃圾半好氧生物反应器填埋技术是中国中小城市垃圾填埋处理的发展方向.     

城市生活垃圾填埋初期有机质演化规律研究

为阐明生活垃圾填埋初期有机质演化规律,于填埋场打井采集填埋1～3年3个不同时期垃圾样品,用水浸提制备水溶性有机物(DOM)。采用红外光谱、同步荧光光谱及紫外光谱,对浸提液中DOM的结构和演化特征进行了研究。结果显示,生活垃圾中含有脂肪类、蛋白类、糖类及木质素类物质,在填埋初期,有机质中的脂肪类、蛋白质类、糖类及木质素类物质均发生了降解,羧基、氨类及水溶性芳香结构物质减少,DOM分子量降低。研究结果表明,垃圾填埋初期有机质以降解为主。     

Household hazardous waste disposal to landfill: using LandSim to model leachate migration

Municipal solid waste (MSW) landfill leachate contains a number of aquatic pollutants. A specific MSW stream often referred to as household hazardous waste (HHW) can be considered to contribute a large proportion of these pollutants. This paper describes the use of the LandSim (Landfill Performance Simulation) modelling program to assess the environmental consequences of leachate release from a generic MSW landfill in receipt of co-disposed HHW. Heavy metals and organic pollutants were found to migrate into the zones beneath a model landfill site over a 20,000-year period. Arsenic and chromium were found to exceed European Union and US-EPA drinking water standards at the unsaturated zone/aquifer interface, with levels of mercury and cadmium exceeding minimum reporting values (MRVs). The findings demonstrate the pollution potential arising from HHW disposal with MSW.     

西南地区某已封场非规范垃圾填埋场垃圾稳定化进程分析

以重庆某非规范填埋场为例,针对西南地区已封场非规范垃圾填埋场的稳定化进程进行了分析。按照场地布局选取4个采样点,在垃圾体上进行钻孔取样,分析不同深度的垃圾样pH值、有机质、含水率、生物可降解度以及垃圾样浸出液和填埋气组成以及各个指标随着填埋深度的变化规律,确定不同深度垃圾体的稳定化程度。结果表明,场内垃圾已呈现矿化垃圾特征;有机质、BDM、浸出液COD以及填埋气CH4含量等4个指标与填埋深度均较好地符合一级降解反应,可以预测垃圾体稳定化临界填埋深度。根据有机质、BDM、浸出液COD以及填埋气CH4含量等4个指标与填埋深度一级降解反应函数预测临界稳定化深度为15 m,与实测值判定的稳定化填埋深度相一致性。在对非规范垃圾填埋场场地利用过程中,需要先对未稳定的上层垃圾进行清理,并在已稳定的底层垃圾体上充填其他稳定介质后利用该地块。     

填埋垃圾腐殖质组成在填埋场稳定度表征中的应用

通过对上海老港生活垃圾填埋场1991-2004年封场单元填埋垃圾腐殖质组成的分析,考察了填埋垃圾中腐殖质组成随填埋龄的变化规律.研究结果表明,填埋垃圾腐殖质的总可提取率和胡敏酸(HA)与富里酸(FA)比值(HA/FA)分别随填埋龄呈线性下降和上升趋势.因此,填埋垃圾总可提取率和HA/FA可用来有效表征填埋场和填埋垃圾稳定度.     

Municipal solid waste shear strength parameters defined through laboratorial and in situ tests

This paper presents the parameters of municipal solid waste shear strength determined in the laboratory (triaxial tests) and by in situ tests: standard penetration tests (SPT) and cone penetration tests (CPT). The results analyzed here are part of a study carried out on the Santo Tirso landfill (north of Portugal) between 2001 and 2007. The influence of the strain levels, waste composition, and waste age on the shear strength parameters is presented, as well as an attempt to establish some correlations between the SPT and CPT tests and to estimate municipal solid waste (MSW) friction angles from the SPT tests. The results indicate that the aging of the waste, which is characterized by a decrease in fibrous and organic materials and an increase in inert materials and fine fraction, leads to an increase in frictional resistance and to a decrease in cohesion. The results of the SPT and CPT tests indicate higher penetration resistance in older and deeper waste. Estimating the frictional resistance from the SPT test seems to obey an empirical relationship expressed by a power function, which depends on the strain level.

Implications: Comparison of shear strength parameters of municipal solid waste (MSW) determined through laboratory (triaxial tests) and in situ tests (SPT and CPT) showed that the greater amount of fibrous and granular elements leads to an increase in “cohesion” and in friction angle values, respectively. Waste aging results in an increase in frictional resistance and in a decrease in “cohesive” resistance. This is consistent with the composition changes with aging: increase of the relative quantity of inert materials and fine fraction, and decrease in particle size, in organic matter content, and in fabrics and plastics.