垃圾填埋场加速稳定化表征指标的相关性分析

加速稳定化表征指标是生物反应器填埋技术评价的重要内容。通过垃圾填埋室内模拟实验,研究不同运行工况下垃圾挥发性固体(VS)、生物可降解物(BDM)、纤维素(C)和纤维素/木质素(C/L)等组分指标的动态变化规律及其对加速稳定化进程的指示作用,进而探寻各指标之间的相关性,进一步筛选确定垃圾填埋场加速稳定化进程的核心表征指标。结果表明,垃圾组分VS、BDM、C和C/L的衰减符合一级反应动力学,其动态变化能够较为灵敏地指示渗滤液回灌和通风供氧对垃圾稳定化的显著加速作用,可作为垃圾填埋场加速稳定化进程的表征指标。VS、BDM、C和C/L相互之间具有良好的正线性相关性。BDM和C/L适宜作为垃圾填埋场加速稳定化进程的核心表征指标。     

非规范生活垃圾填埋场填埋气横向迁移规律及控制

我国城市中尚有大量非规范生活垃圾填埋场存在,对其进行污染整治消除填埋气导致的环境安全隐患刻不容缓.以重庆某垃圾填埋场为例,研究重庆市主城区的非规范生活垃圾填埋场填埋气的横向迁移问题,在垃圾场周边区域布设36个监测井,对监测井中的填埋气进行分析监测,以填埋气特征组分CH4气体的体积浓度变化研究填埋气的横向迁移规律.结果表明,监测井到填埋场边界的距离为监测井中CH4气体浓度的主要影响因素;垃圾场周边距离填埋场场界50 m以外的区域,填埋气的横向迁移已经相当微弱;但是距离填埋场边界50 m以内区域的填埋气的横向迁移明显,需要在距离填埋场边界50 m范围内采取措施与场内填埋气的导排措施配合,进行填埋气的污染控制.     

准好氧填埋场FSQ标准的室内模拟研究

以室内模拟实验为基础,对准好氧填埋场的FSQ标准作了相关研究.实验结果表明,准好氧填埋的渗滤液COD与其他指标的变化具有明显的不同步性,根据该特点,把准好氧填埋场的稳定化过程划分为不稳定、基本稳定和完全稳定3个阶段.相应把准好氧填埋的FSQ标准分为2级:基本稳定状态时的FSQ二级标准,完全稳定状态时的FSQ一级标准.在评价基本稳定状态时,场地沉降量为控制性指标,确定准好氧填埋的FSQ二级标准为:填埋场地总沉降量占垃圾初始填埋高度的比例≥30%,渗滤液COD≤400 mg/L、NH3-N≤15 mg/L、TVS/TDS≤6%,固相垃圾BDM≤6%;在评价完全稳定状态时,渗滤液COD作为控制性指标,概化总结出准好氧填埋的FSQ一级标准为:填埋场地总沉降量占垃圾初始填埋高度的比例＞30%,渗滤液COD≤100 mg/L、NH3-N≤15mg/L、TVS/TDS≤3%,固相垃圾BDM≤3%.     

高温微生物菌剂加速垃圾填埋场好氧稳定化进程的研究

研究了一种可加速垃圾填埋场好氧稳定化进程的生物强化技术。实验对比了A、B、C 3种填埋方式,A、B为好氧填埋,C为厌氧填埋;A中接种高温复合菌剂,B、C中不接种菌剂。实验周期为20 d。研究发现:高温菌剂的投加起到了多重作用:增强了微生物的活动,导致A中的温度显著升高,最高可达72℃,且50℃以上的高温期达14 d,而B仅在45℃维持3 d,C则基本处于常温;加速了垃圾堆体的降解与稳定化进程,至实验结束,A中可生物降解有机质含量(BDM)去除率达51.2%,明显高于B、C中的BDM去除率(31.1%和39.4%);加速了堆体中含氮物质的降解与转化,减少了垃圾浸出液中氨氮的累积;加速了堆体的沉降,A中垃圾堆体沉降高度达10 cm,远大于B、C堆体的沉降高度(4 cm和2.5 cm)。     

微生物菌剂对好氧填埋垃圾稳定过程的影响

为加速好氧填埋场的稳定化进程,提出利用生物强化技术加速好氧填埋垃圾的生物降解,通过模拟实验,研究了微生物菌剂对填埋垃圾稳定过程的影响。结果表明:微生物菌剂降低了好氧填埋场的有机污染负荷,使渗滤液COD下降更加明显,整个填埋周期所产渗滤液的COD总量较对照组少20.20%;加速了含氮物质的生物转化,氨氮峰值出现较对照组提前6 d,经历峰值以后,氨氮快速下降,较对照组提前22 d达到国家生活垃圾填埋场污染控制标准(GB 16889-2008)所规定的渗滤液氨氮排放标准25 mg/L,并使整个填埋周期氨氮总量减少9.15%;微生物菌剂降低了渗滤液的产量,使整个填埋周期渗滤液累计产量减少8.29%;使垃圾中有机质降解加快并使其降解更加彻底,至实验结束时总有机质含量较对照组低8.82%,干重较对照组减少35.95%;沉降性能优于对照组,至填埋结束时较对照组沉降量提高6.35%。     

南京地区简易生活垃圾堆场的污染现状和稳定化评价

针对南京市废弃简易生活垃圾堆场,通过采集和分析渗滤液以及堆体不同深度固体样品,研究其污染现状和稳定化程度。结果表明,渗滤液COD、NH3-N、TN超标倍数分别为4～6倍、7～10倍和4～10倍;固体样品TOC含量在10%左右,含水率在25%左右,均处于基本稳定的水平;固体样品浸出液COD 39～249 mg/L、NH3-N 0.9～14.88 mg/L、TN 8.82～28.14 mg/L。为了评价稳定化程度,确定了3因子:渗滤液、固体样品、浸出液及6个参数:COD,NH3-N,含水率,TOC,COD,TN作为评价指标,评价结果表明堆场处于基本稳定到中度稳定阶段。     

垃圾降解过程中淀粉酶活性测定条件优化

垃圾填埋场中垃圾降解初期,淀粉酶活性对于垃圾填埋场中碳素的转化过程和垃圾填埋场生物学特性的研究有重要意义,而且也可作为垃圾填埋场稳定化机制研究的重要指标之一.以模拟垃圾填埋系统的垃圾为研究对象,通过正交实验(L25(56))对淀粉酶活性的测定条件进行了优化研究.结果表明:(1)正交实验结果表明,对淀粉酶活性测定的影响大...     

消化污泥作为垃圾填埋场覆盖材料的研究

为解决城市污染,实现污泥"减量化、无害化、稳定化、资源化"的目标,有必要寻求更多技术上可行、低成本的污泥综合利用新技术.测定了消化污泥本底的含水率、有机质含量以及经过预处理后不同含水率的消化污泥模拟降雨实验的渗透系数,浸出液的COD、氨氮、pH等.选择渗透系数低、污染负荷小的含水率为50%和60%的消化污泥,分别与石灰、炉渣以不同比例混合改性后,再测定模拟降雨实验浸出液的各个指标.实验结果表明,含水率为60%的消化污泥与炉渣以2∶1(质量比)混合时,渗透系数达到10-6数量级,已接近垃圾填埋场对防渗层的要求.因此,消化污泥改性后可作为垃圾填埋场覆盖材料.     

大型垃圾填埋场垃圾稳定化研究

本文对大型垃圾填埋场内不同填埋时间垃圾四个组分 (总糖、有机质、生物可降解物和粗纤维 )含量进行了分析 ,并对各指标随填埋时间的变化趋势进行了讨论。结果表明 :在试验场封场后不久 ,垃圾取样均匀性不能保证 ,各指标随时间变化波动很大 ;封场 71 8d后 ,各指标随时间变化呈现一定的规律性 ,垃圾的生物可降解物含量变化能较好地反映垃圾的降解规律。     

大型垃圾填埋场垃圾稳定化研究

本文对大型垃圾填埋场内不同填埋时间垃圾四个组分（总糖、有机质、生物可降解物和粗纤维）含量进行了分析,并对各指标随填埋时间的变化趋势进行了讨论。结果表明：在试验场封场后不久,垃圾取样均匀性不能保证,各指标随时间变化波动很大;封场718d后,各指标随时间变化呈现一定的规律性,垃圾的生物可降解物含量变化能较好地反映垃圾的降解规律。     

城市生活垃圾填埋初期有机质演化规律研究

为阐明生活垃圾填埋初期有机质演化规律,于填埋场打井采集填埋1～3年3个不同时期垃圾样品,用水浸提制备水溶性有机物(DOM)。采用红外光谱、同步荧光光谱及紫外光谱,对浸提液中DOM的结构和演化特征进行了研究。结果显示,生活垃圾中含有脂肪类、蛋白类、糖类及木质素类物质,在填埋初期,有机质中的脂肪类、蛋白质类、糖类及木质素类物质均发生了降解,羧基、氨类及水溶性芳香结构物质减少,DOM分子量降低。研究结果表明,垃圾填埋初期有机质以降解为主。     

Biodegradation of organic matters from mixed unshredded municipal solid waste through air convection before landfilling

Landfilling is a dominant municipal solid waste (MSW) disposal method in most developing countries. In China, approximately 85% of the generated MSW is being disposed of in the landfills. The amount of MSW is growing rapidly with the rate of approximately 8-10% annually, which contains a high quantity of moisture and organic matters. The problems of leachate treatment and landfill gas (LFG) emissions are increasing gradually. Reducing the hazard before emplacement, pretreatment of MSW before landfilling has become very important for the conventional landfill. In this study, aerobic pretreatment of mixed MSW was used, and much attention has been given to the natural convection of air in the mixed and unshredded MSW for bioconversion of organic matter (OM). This study is an attempt to investigate aerobic pretreatment suitability for the mixed and unshredded MSW at Beijing. A pilot-scale aerobic pretreatment simulator (APS) was developed at Beishen Shu Landfill in Beijing. To work out the biodegradation of the OM in the APS, fresh and pretreated MSW samples were collected and analyzed for OM, moisture content, temperature, chemical oxygen demand, total organic carbon, carbon, nitrogen, hydrogen, lignocelluloses, and biochemical methane potential at various stages of the pretreatment. Furthermore, results of the fresh and pretreated MSW are compared. Significant reduction in the observed parameters of the pretreated waste samples is observed. This work demonstrates that pretreatment is significantly effective in reducing the landfill emissions that is leachate and LFG.     

间歇式生物反应器填埋结构对渗滤液水质的影响研究

通过2套间歇式生物反应器填埋模拟装置开展实验,对不同填埋结构下垃圾降解前期渗滤液pH值、COD、NH 4＋-N、VFA以及渗滤液产生量的变化规律进行了对比研究。实验结果表明：间歇式生物反应器填埋方式能够有效抑制填埋初期渗滤液pH值的快速下降,渗滤液采取部分回灌能有效降低NH4＋-N浓度的积累,新鲜垃圾与半腐熟垃圾分层并...     

城市生活垃圾半好氧生物反应器填埋技术试验研究

对城市生活垃圾半好氧生物反应器填埋技术与传统垃圾填埋技术进行了对比试验,由试验结果可知,半好氧生物反应器填埋技术可缩短填埋垃圾产酸时间,净化渗滤液,加速填埋垃圾稳定化进程.城市生活垃圾半好氧生物反应器填埋技术是中国中小城市垃圾填埋处理的发展方向.     

The role of mechanical and biological treatment in reducing methane emissions from landfill disposal of municipal solid waste in the United Kingdom

In Europe, the European Union Landfill Directive aims to reduce the negative environmental impacts of landfilling. This is mainly to be achieved by reducing the quantity of organic matter deposited, through measures such as the separate collection and recycling of the organic waste stream or pretreatment of residual wastes before landfilling. Other than incineration or other thermal processes, mechanical biological treatment is playing an increasingly important role. This study was conducted to seek the benefits of municipal solid waste (MSW) pretreatment, as well as the differences in methane production from the landfilling of untreated and mechanically/biologically treated (MBT) MSW using GasSim simulation. Results demonstrated that methane production rates vary significantly among waste fractions. Those that contribute most to methane generation (organic material and potentially reusable or recyclable material) could be targeted and treated before landfilling. The statistic relationship from the first phase of the study indicated that to match the increasingly stringent landfill waste organic content allowance, local councils should prioritize the reduction/sorting of certain targeted fractions, such as paper, card, green waste, and other putrescibles from MSW. Moreover, mechanical treatment alone produces organic-rich waste called mechanically sorted organic residues (MSORs), which can be viewed as an organic content concentration process. Mechanically and biologically pretreated waste, on the other hand, differs significantly from untreated MSW and MSORs. This work demonstrated that if efficient mechanical-biological treatment is used, considerable reductions in biological activity, landfill gas production, and energy content/total organic carbon could be achieved. Using GasSim, reductions in methane production of >74% have been simulated if a 90% organic content reduction can be achieved during biological treatment on MSORs. A 50-60% organic content reduction by following biological treatment can turn MSOR properties only into normal MSW equivalent though considerably less volume.     

Leaching characteristics of PCDDs/DFs and dioxin-like PCBs from landfills containing municipal solid waste and incineration residues

To investigate the leaching characteristic of persistent organic pollutants (POPs), such as non-ortho and mono-ortho substituted chlorobiphebyls (dioxin-like PCBs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/DFs), in leachate from municipal solid waste (MSW) landfill sites containing incineration residues, raw leachate samples were collected twice from 12 selected MSW landfill sites. The samples were divided into their liquid and solid phases using GF/B (pore size 1.0 microm), and the concentrations of POPs then determined. The concentrations of PCDDs/DFs ranged from 0.65 to 5.88 pg-TEQ/l (average 2.86 pg-TEQ/l), and those of dioxin-like PCBs from 0.05 to 0.32 pg-TEQ/l (average 0.18 pg-TEQ/l). The major congeners of leached PCDDs/DFs and dioxin-like PCBs in liquid and solid phases were OCDD (about 60%), 2,3',4,4',5-PeCBs (about 30%), and 2,3,4,4',5-PeCBs (about 54%). The relationship between landfill age and the leaching concentration of PCDDs/DFs, and effects of dissolved organic carbon (DOC) on the leaching of PCDDs/DFs are also discussed. Finally, a leaching prediction model of PCDDs/DFs from MSW landfills has been suggested using parameters, such as hydrophobic neutral organic carbons, total dissolved solid, and the ratio of non-biodegradable wastes in landfill sites.     

垃圾焚烧厂焚烧底灰的处理研究

系统地研究了常州市环境卫生综合厂垃圾焚烧车间的底灰。研究结果表明，根据中国现行的污染控制标准，该厂的底灰属于一般废物，可以以建筑垃圾的方式处理。但对底灰的分选和分类研究结果表明，底灰含有一定量的未燃烬的有机废物，也有一些可回收利用的废物。因此，底灰应该先分选后，再对无利用价值的渣土作填埋或其他处置。     

Household hazardous waste disposal to landfill: using LandSim to model leachate migration

Municipal solid waste (MSW) landfill leachate contains a number of aquatic pollutants. A specific MSW stream often referred to as household hazardous waste (HHW) can be considered to contribute a large proportion of these pollutants. This paper describes the use of the LandSim (Landfill Performance Simulation) modelling program to assess the environmental consequences of leachate release from a generic MSW landfill in receipt of co-disposed HHW. Heavy metals and organic pollutants were found to migrate into the zones beneath a model landfill site over a 20,000-year period. Arsenic and chromium were found to exceed European Union and US-EPA drinking water standards at the unsaturated zone/aquifer interface, with levels of mercury and cadmium exceeding minimum reporting values (MRVs). The findings demonstrate the pollution potential arising from HHW disposal with MSW.     

砒霜生产化工厂危险废物处置工程设计

通过对砒霜生产化工厂原场址废渣及污染场地调查的基础上，进行了处置方案比选及技术经济比较，确定了就地安全填埋的处置方案。根据区域性危险废物集中安全填埋场的设计经验，本工程采用先进的HDPE双层防渗的安全填埋方式，并设置了雨水分流系统、渗滤液收集系统、封场处理和填埋气体导排系统，整个场区布置合理，对周围环境的影响小，投资少，取得了良好的社会效益和环境效益，并对危险废物处理处置工程设计中应注意的问题提出了建议。