Enhanced anaerobic bioremediation of a TCE source at the Tarheel Army Missile Plant using EOS

EOS, or emulsified oil substrate, was used to stimulate anaerobic biodegradation of trichloroethene (TCE) and tetrachloroethene (PCE) at a former Army‐owned manufacturing facility located in the Piedmont area of North Carolina. Previous use of chlorinated solvents at the facility resulted in soil and groundwater impacts. Ten years of active remediation utilizing soil vacuum extraction and air sparging (SVE/AS) were largely ineffective in reducing the TCE/PCE plume. In 2002, the Army authorized preparation of an amended Remedial Action Plan (RAP) to evaluate in situ bioremediation methods to remediate TCE in groundwater. The RAP evaluated eight groundwater remediation technologies and recommended EOS as the preferred bioremediation alternative for the site. Eight wells were drilled within the 100 × 100 feet area believed to be the primary source area for the TCE plume. In a first injection phase, dilute EOS emulsion was injected into half of the wells. Distribution of the carbon substrate through the treatment zone was enhanced by pumping the four wells that were not injected and recirculating the extracted water through the injection wells. The process was repeated in a second phase that reversed the injection/extraction well pairs. Overall, 18,480 pounds of EOS were injected and 163,000 gallons of water were recirculated through the source area. Anaerobic groundwater conditions were observed shortly after injection with a corresponding decrease in both PCE and TCE concentrations. Dissolved oxygen, oxidation‐reduction potential, and sulfate concentrations also decreased after injection, while TCE‐degradation products, ferrous iron, and methane concentrations increased. The reduction in TCE allowed the Army to meet the groundwater remediation goals for the site. Approximately 18 months after injection, eight wells were innoculated with a commercially prepared dechlorinating culture (KB‐1) in an attempt to address lingering cis‐1,2‐dichloroethene (cis‐DCE) and vinyl chloride (VC) that continued to be observed in some wells. Dehalococcoides populations increased slightly post‐bioaugmentation. Both cis‐DCE and VC continue to slowly decrease. © 2007 Wiley Periodicals, Inc.     

Reductive dechlorination of a chlorinated solvent plume in Houston,Texas

Chlorinated solvents such as tetrachloroethene (perchloroethene, PCE) and trichloroethene (TCE) have been extensively used in various industrial applications for many years. Because neither are typically consumed through their various uses, they are often released to the environment through industrial application or disposal. Once released, PCE and TCE tend to migrate downward into groundwater, where they persist. In the current case study, cheese whey was used as a groundwater amendment to facilitate the reductive dechlorination of a chlorinated solvent plume underlying an auto dealer/repair shop in Harris County, Texas. From September 2010 to January 2014, over 32,000 gallons of cheese whey were injected into the subsurface resulting in a marked reduction in oxidation–reduction potential (ORP) and nitrate concentrations, coupled with an increase in ferrous iron concentrations. Statistical trend analyses indicate the primary contaminants, PCE and TCE, as well as the daughter product cis‐1,2‐dichloroethene (cDCE), all exhibited a positive response, as evidenced by statistically decreasing trends, and/or reversal in concentration trends, subsequent to cheese whey injections. Maximum concentrations of PCE and TCE in key test wells decreased by as much as 98.97 percent and 99.17 percent, respectively. In addition, the bacterial genus Dehalococcoides, capable of complete reduction of PCE to non‐toxic ethene, was found to be more abundant in the treatment area, as compared to background concentrations. Because cheese whey is a by‐product of the cheese making process, the cost of the product is essentially limited to transport. This study demonstrates cheese whey to be an effective groundwater amendment at a cost which is orders of magnitude lower than popular industry alternatives.     

Hydrogen Release Compound: A Cost‐Effective Alternative to PCE Remediation at Dry Cleaning Facilities

Tetrachloroethylene, also known as perchloroethylene or PCE, is one of the most difficult to treat chlorinated solvents when present in groundwater. Unfortunately, this elusive and recalcitrant compound is also the most commonly used dry cleaning solvent. As a result, releases of PCE at dry cleaning sites are somewhat common. Regenesis Bioremediation Products, of San Clemente, California, has developed Hydrogen Release Compound (HRC), which has been successfully used to promote bioremediation of PCE in groundwater. This product is directly injected into contaminated groundwater to speed up the natural attenuation of PCE through an anaerobic, natural process known as reductive dechlorination. A key benefit of HRC is its ability to slowly release hydrogen over extended periods of time. Reductive dechlorination relies on a steady source and readily available supply of electron donors as part of the degradation process. Hydrogen is one of the best electron donors available, and thus, the application of HRC significantly enhances the rate of PCE degradation. For dry cleaners, this technology can substantially reduce major design, capital, and operating costs, allowing the implementation of a low‐impact application and remediation solution. This article discusses the use of the HRC to remediate PCE contamination and presents the results of two specific HRC‐treated dry cleaner sites. © 2002 Wiley Periodicals, Inc.     

Successful full‐scale enhanced anaerobic dechlorination at a NAPL strength 1,1,1‐TCA source area

Bioremediation of 1,1,1‐trichloroethane (TCA) is more challenging than bioremediation of other chlorinated solvents, such as tetrachloroethene (PCE) and trichloroethene (TCE). TCA transformation often occurs under methanogenic and sulfate‐reducing conditions and is mediated by Dehalobacter. The source area at the project site contains moderately permeable medium sand with a low hydraulic gradient and is approximately 0.5 acre. TCA contamination generally extended to 35 feet, with the highest concentrations at approximately 20 feet. The concentrations then decreased with depth; several wells contained 300 to 600 mg/L of TCA prior to bioremediation. The area of treatment also contained 2 to 30 mg/L of TCE from an upgradient source. Initial site groundwater conditions indicated minimal biotic dechlorination and the presence of up to 20 mg/L of nitrate and 90 mg/L of sulfate. Microcosm testing indicated that TCA dechlorination was inhibited by the site's relatively low pH (5 to 5.5) and high TCA concentration. After the pH was adjusted and TCA concentrations were reduced to less than 35 mg/L (by dilution with site water), dechlorination proceeded rapidly using whey (or slower with sodium lactate) as an electron donor. Throughout the remediation program, increased resistance to TCA inhibition (from 35 to 200 mg/L) was observed as the microbes adapted to the elevated TCA concentrations. The article presents the results of a full‐scale enhanced anaerobic dechlorination recirculation system and the successful efforts to eliminate TCA‐ and pH‐related inhibition. © 2012 Wiley Periodicals, Inc.     

Remedial options for chlorinated volatile organics in a partially anaerobic aquifer

A laboratory study was conducted for the selection of appropriate remedial technologies for a partially anaerobic aquifer contaminated with chlorinated volatile organics (VOCs). Evaluation of in situ bioremediation demonstrated that the addition of electron donors to anaerobic microcosms enhanced biological reductive dechlorination of tetrachloroethene (PCE), trichloroethene (TCE), and 1,1,1‐trichloroethane (1,1,1‐TCA) with half‐lives of 20, 22, and 41 days, respectively. Nearly complete reductions of PCE, TCE, 1,1,1‐TCA, and the derivative cis‐dichloroethene were accompanied by a corresponding increase in chloride concentrations. Accumulation of vinyl chloride, ethene, and ethane was not observed; however, elevated levels of ¹⁴CO₂ (from ¹⁴C‐TCE spiked) were recovered, indicating the occurrence of anaerobic oxidation. In contrast, very little degradation of 1,2‐dichloropropane (1,2‐DCP) and 1,1‐dichlorethane (1,1‐DCA) was observed in the anaerobic microcosms, but nutrient addition enhanced their degradation in the aerobic biotic microcosms. The aerobic degradation half‐lives for 1,2‐DCP and 1,1‐DCA were 63 and 56 days, respectively. Evaluation of in situ chemical oxidation (ISCO) demonstrated that chelate‐modified Fenton's reagent was effective in degrading aqueous‐phase PCE, TCE, 1,1,1‐TCA, 1,2‐DCP, etc.; however, this approach had minimal effects on solid‐phase contaminants. The observed oxidant demand was 16 g‐H₂O₂/L‐groundwater. The oxidation reaction rates were not highly sensitive to the molar ratio of H₂O₂:Fe²⁺:citrate. A ratio of 60:1:1 resulted in slightly faster removal of chemicals of concern (COCs) than those of 12:1:1 and 300:1:1. This treatment resulted in increases in dissolved metals (Ca, Cr, Mg, K, and Mn) and a minor increase of vinyl chloride. Treatment with zero‐valent iron (ZVI) resulted in complete dechlorination of PCE, and TCE to ethene and ethane. ZVI treatment reduced 1,1,1‐TCA only to 1,1‐DCA and chloroethane (CA) but had little effect on reducing the levels of 1,2‐DCP, 1,1‐DCA, and CA. The longevity test showed that one gram of 325‐mesh iron powder was exhausted in reaction with > 22 mL of groundwater. The short life of ZVI may be a barrier to implementation. The ZVI surface reaction rates (k_sa) were 1.2 × 10^?2 Lm^?2h^?1, 2 × 10^?3 Lm^?2h^?1, and 1.2 × 10^?3 Lm^?2h^?1 for 1,1,1‐TCA, TCE, and PCE, respectively. Based upon the results of this study, in situ bioremediation appeared to be more suitable than ISCO and ZVI for effectively treating the groundwater contamination at the site. © 2004 Wiley Periodicals, Inc.     

Field Evidence of Dissolution and Degradation Rates Enhancement During ISCR and ENA Treatments of Chlorinated Solvents

This article presents field tests comparing two methods of treatment of chlorinated solvents undertaken at the same site. The site is an automobile factory where two chlorinated solvents (CS) plumes were identified. At the first source, in situ chemical reduction (ISCR) was applied, while at the second one, enhanced natural attenuation (ENA) was used. A set of specific multilevel sampling wells were installed approximately 20 m downgradient of the sources to estimate the efficiency of the treatments. The presence of a low‐permeability layer (source 1) or a thick oil lens (source 2) in the top part of the aquifer prevented the CS from reaching the bottom of the aquifer. These layers led to difficulties treating the contamination. At the ISCR and ENA treatment zones, the concentrations of tetrachloroethene (PCE) and trichloroethene (TCE) did not change significantly, while the concentration of metabolites (cis‐1,2‐DCE, vinyl chloride, and ethene) significantly increased 50 to 150 days after treatment. Due to high concentration of CS in the source zone, a mass balance calculation, including chlorine, was possible. It showed that around 1 to 2 percent of the injected products were used to reduce the CS. A detailed analysis and 1D analytical modeling of CS concentrations showed that the treatment led to a large (two to three times) increase in dissolution of the organic phase. This explains why, despite an efficient treatment, the PCE and TCE concentrations remained virtually unchanged. Degradation rates also increased due to the treatment. Due to some differences in the source‐zone chemistry, it was not possible to differentiate between the ISCR and ENA efficiencies. © 2013 Wiley Periodicals, Inc.     

Successful ISCR‐enhanced bioremediation of a TCE DNAPL source utilizing EHC® and KB‐1®

Remediation of chlorinated solvent DNAPL sites often meets with mixed results. This can be attributed to the diametrically opposed nature of the impacts, where the disparate dissolved‐phase plume is more manageable than the localized, high‐concentration source area. A wide range of technologies are available for downgradient plume management, but the relative mass of contaminants in a DNAPL source area generally requires treatment for such technologies to be effective over the long term. In many cases, the characteristics of DNAPL source zones (e.g., depth, soil heterogeneity, structural limitations) limit the available options. The following describes the successful full‐scale implementation of in situ chemical reduction (ISCR) enhanced bioremediation of a TCE DNAPL source zone. In this demonstration, concentrations of TCE were rapidly reduced to below the maximum contaminant level (MCL) in less than six months following implementation. The results described herein suggest that ISCR‐enhanced bioremediation is a viable remedial alternative for chlorinated solvent source zones. © 2010 Wiley Periodicals, Inc.     

Treatment Optimization Through Refinement of a Conceptual Site Model Using Compound Specific Isotope Analysis

Two adjacent automotive component manufacturers in Japan had concentrations of trichloroethene (TCE) and perchloroethene (PCE) in soils and groundwater beneath their plants. One of the manufacturers extensively used these solvents in its processes, while the adjacent manufacturer had no documentation of solvent use. The conceptual site model (CSM) initially involved a single source that migrated from one building to under the adjacent building. Further, because low concentrations of daughter products (e.g., cis‐1,2‐dichloroethene; 3.6 to 840 micrograms per liter [μg/L]) were detected in groundwater, the CSM did not consider intrinsic degradation to be a significant fate mechanism. With this interpretation, the initial remedial design involved both source treatment and perimeter groundwater control to prevent offsite migration of the solvents in groundwater. Identifying whether intrinsic degradation was occurring and could be quantified represented a means of eliminating this costly and potentially redundant component. Further, incorporating intrinsic degradation into the remediation design would also allow for a more focused source treatment, resulting in further cost savings. Three rounds of sampling and data interpretation applying compound specific isotope analysis (CSIA) were used to refine the CSM. The first sampling round involved three‐dimensional CSIA (¹³C, ³⁷Cl, and ²H), while the second two rounds involved ¹³C only, focusing on degradation over time. For the May 2012 sampling, δ¹³C for PCE ranged from –31‰ to –29.6 ‰ and for TCE ranged from –30.4‰ to –28.3‰; showing similar values. δ²H for TCE ranged from 581‰ to 629‰, indicating a manufactured TCE rather than that resulting from dehalogenation processes from PCE. However, mixing of manufactured TCE with that resulting from degraded PCE cannot be ruled out. Because of the similar δ¹³C ratios for PCE and TCE, and ³⁷Cl data for PCE and TCE, fractionation and enrichment factors could not be relied upon. Fractionation patterns were evaluated using graphical methods to trace TCE to the source location to better focus the locations for steam injection. Graphical methods were also used to define the degradation mechanism and from this, incorporate intrinsic degradation processes into the remedial design, eliminating the need for a costly perimeter pump and treat system. ©2015 Wiley Periodicals, Inc.     

Practical Perspectives of 1,4‐Dioxane Investigation and Remediation

1,4‐Dioxane (dioxane) is a contaminant of emerging concern that is classified by the U.S. Environmental Protection Agency as a likely human carcinogen. Dioxane has been used as a minor or major ingredient in many applications, and is also generated as an unwanted by‐product of industrial processes associated with the manufacturing of polyethylene, nonionic surfactants, and many consumer products (cosmetics, laundry detergents, shampoos, etc.). Dioxane is also a known stabilizer of chlorinated solvents, particularly 1,1,1‐trichloroethane, and has been commonly found comingled with chlorinated solvent plumes. Dioxane plumes at chlorinated solvent sites can complicate site closure strategies, which to date have not typically focused on dioxane. Aggressive treatment technologies have greatly advanced and are clearly capable of achieving lower parts per billion cleanup criteria using ex situ advanced oxidation processes and sorption media. In situ chemical oxidation has also been demonstrated to effectively remediate dioxane and chlorinated solvents. Other in situ remedies, such as enhanced bioremediation, phytoremediation, and monitored natural attenuation, have been studied; however, their ability to achieve cleanup levels is still somewhat questionable and is limited by co‐occurring contaminants. This article summarizes and provides practical perspectives on dioxane analysis, plume stability relative to other contaminants, and the development of investigation tools and treatment technologies.     

Successful solid-phase bioremediation of petroleum-contaminated soil

Biological processes have been used to remediate petroleum hydrocarbons, pesticides, chlorinated solvents, and halogenated aromatic hydrocarbons. Biological treatment of contaminated soils may involve solid-phase, slurry-phase, or in situ treatment techniques. This article will review the general principle of solid-phase bioremediation and discuss the application of this technique for the cleanup of total petroleum hydrocarbons on two sites. These remedial programs will reduce total petroleum hydrocarbon contamination from the mean concentration of 2,660 ppm to under the 200-ppm cleanup criteria for soil and under the 15-ppm cleanup criteria for groundwater. Over 32,000 yards of soil have been treated by solid-phase treatment to date. The in situ system operation is effectively producing biodegradation in the subsurface. The project is approximately one-third complete.     

Evaluation of soil solid amendments for TCE biodegradation in a biobarrier system

Permeable biobarrier systems (PBSs) are being recognized as low‐cost passive bioremediation technologies for chlorinated organic contamination. This innovative technology can play a crucial and effective role in site restorations. Laboratory‐scale experiments were conducted to investigate the biodegradation of trichloroethylene (TCE) to ethylene in shallow groundwater through the use of a PBS enhanced by bioaugmentation at the U.S. Department of Energy's Savannah River Site (SRS). Two composts and two plant amendments, eucalyptus mulch (EM) and corncobs (CC), were examined for their effectiveness at creating and maintaining conditions suitable for TCE anaerobic dechlorination. These materials were evaluated for their (1) nutrient and organic carbon content, (2) TCE sorption characteristics, and (3) longevity of release of nutrients and soluble carbon in groundwater to support TCE dechlorination. Native bacteria in the columns had the ability to convert TCE to dichloroethenes (DCEs); however, the inoculation with the TCE‐degrading culture greatly increased the rate of biodegradation. This caused a significant increase in by‐product concentration, mostly in the form of DCEs and vinyl chloride (VC) followed by a slow degradation to ethylene. Of the tested amendments, eucalyptus mulch was the most effective at supporting the reductive dechlorination of TCE. Corncobs created a very acidic condition in the column that inhibited dechlorination. © 2007 Wiley Periodicals, Inc.     

Performance evaluation of an in situ source area combined remedy for the remediation of commingled chlorinated ethanes and ethenes

The chlorinated volatile organic compounds (CVOCs), tetrachloroethene (PCE), trichloroethene (TCE), and 1,1,1‐trichloroethane (1,1,1‐TCA), often found as commingled contaminants of concern (COCs) in groundwater, can degrade via a variety of biotic and abiotic reductive pathways. In situ remediation of a groundwater contaminant source area containing commingled 1,1,1‐TCA, PCE, and TCE was conducted using a combined remedy/treatment train approach. The first step was to create geochemically reducing conditions in the source area to degrade the CVOCs to lesser chlorinated CVOCs (i.e., 1,1‐dichloroethane [1,1‐DCA], 1,1‐dichlorethene [1,1‐DCE], cis‐1,2‐dichoroethene [cis‐1,2‐DCE], and vinyl chloride [VC]) via enhanced reductive dechlorination (ERD). Carbon substrates were injected to create microbial‐induced geochemically reducing conditions. An abiotic reductant (zero‐valent iron [ZVI]) was also used to further degrade the CVOCs, minimizing the generation of 1,1‐DCE and VC, and co‐precipitate temporarily mobilized metals. An in situ aerobic zone was created downgradient of the treatment zone through the injection of oxygen. Remaining CVOC degradation products and temporarily mobilized metals (e.g., iron and manganese) resulting from the geochemically reducing conditions were then allowed to migrate through the aerobic zone. Within the aerobic zone, the lesser chlorinated CVOCs were oxidized and the solubilized metals were precipitated out of solution. The injection of a combination of carbon substrates and ZVI into the groundwater system at the site studied herein resulted in the generation of a geochemically reducing subsurface treatment zone that has lasted for more than 4.5 years. Mass concentrations of total CVOCs were degraded within the treatment zone, with near complete transformation of chlorinated ethenes and a more than 90 percent reduction of CVOC mass concentrations. Production of VC and 1,1‐DCE has been minimized through the combined effects of abiotic and biological processes. CVOC concentrations have declined over time and temporarily mobilized metals are precipitating out of the dissolved phase. Precipitation of the dissolved metals was mitigated using the in situ oxygenation system, also resulting in a return to aerobic conditions in downgradient groundwater. Chloroethane (CA) is the dominant CVOC degradation product within the treatment zone and downgradient of the treatment zone, and it is expected to continue to aerobically degrade over time. CA did not accumulate within and near the aerobic oxygenation zone. The expectations for the remediation system are: (1) the concentrations of CVOCs (primarily in the form of CA) will continue to degrade; (2) total organic carbon concentrations will continue to decline to pre‐remediation levels; and, (3) the groundwater geochemistry will experience an overall trend of transitioning from reducing back to pre‐remediation mildly oxidizing conditions within and downgradient of the treatment zone.     

Sodium Persulfate Oxidation for the Remediation of Chlorinated Solvents (USEPA Superfund Innovative Technology Evaluation Program)

This study has been conducted at the University of Connecticut (UCONN) in connection with the USEPA Superfund Innovative Technology Evaluation (SITE) program to evaluate a chemical oxidation technology (sodium persulfate) developed at UCONN. A protocol to assess the efficacy of oxidation technologies has been used. This protocol, which consists of obtaining data from a treatability study, tested two in-situ chemical oxidation technologies that can be used on soil and groundwater at a site in Vernon, Connecticut. Based on the treatability report results and additional field data collected at the site, the design for the field implementation of the chemical oxidation remediation was completed. The results indicate that both sodium persulfate and potassium permanganate were able to effectively degrade the target VOCs (i.e., PCE, TCE and cis-DCE) in groundwater and soil-groundwater matrices. In the sodium persulfate tests (120 hrs), the extent of destruction of target VOCs was 74% for PCE, 86% for TCE and 84% for cis-DCE by Na₂S₂O₈ alone and 68% for PCE, 76% for TCE, and 69% for cis-DCE by Fe(II)-catalyzed Na₂S₂O₈. The results demonstrate the sodium persulfate's ability to degrade PCE, TCE and cis-DCE. It is expected that given sufficient dose and treatment time, a higher destruction rate of the dissolved phase contamination can be achieved. The data also indicates that the catalytic effect of the iron chelate on persulfate chemistry was much less pronounced in the soil-groundwater matrix. This indicates an interaction between the iron chelate solution and the soil, which may have resulted in a lower availability of the chelated iron for catalysis. The study showed that the remediation of the VOCs-contaminated soil and groundwater by in-situ chemical oxidation using sodium persulfate is feasible at the Roosevelt Mills site. As a result, the USEPA SITE program will evaluate this technology at this site.     

Pilot‐scale evaluation using bioaugmentation to enhance PCE dissolution at dover AFB national test site

An Interstate Technology and Regulatory Council (ITRC) forum was recently held that focused on six case studies in which bioremediation of dense nonaqueous‐phase liquids (DNAPLs) was performed; the objective was to demonstrate that there is credible evidence for bioremediation as a viable environmental remediation technology. The first two case studies from the forum have been previously published; this third case study involves a pilot‐scale demonstration that investigated the effects of biological activity on enhancing dissolution of an emplaced tetrachloroethene (PCE) DNAPL source. It used a controlled‐release test cell with PCE as the primary DNAPL in a porous media groundwater system. Both laboratory tests and a field‐scale pilot test demonstrated that bioaugmentation can stimulate complete dechlorination to a nontoxic end product and that the mass flux from a source zone increases when biological dehalorespiration activity is enhanced through nutrient (electron donor) addition and bioaugmentation. All project goals were met. Important achievements include demonstrating the ability to degrade a PCE DNAPL source to ethene and obtaining significant information on the impacts to the microbial populations and corresponding isotope enrichments during biodegradation of a source area. © 2007 Wiley Periodicals, Inc.     

SITE Demonstration of Enhanced In-Situ Bioremediation of Chlorinated and Nonchlorinated Organic Compounds in Fractured Bedrock

A field demonstration of an enhanced in-situ bioremediation technology was conducted between March 1998 and August 1999 at the ITT Industries Night Vision (ITTNV) Division plant in Roanoke, Virginia. The bioremediation process was evaluated for its effectiveness in treating both chlorinated and nonchlorinated volatile organic compounds (VOCs) in groundwater located in fractured bedrock. Chlorinated compounds, such as trichloroethene (TCE), in fractured bedrock pose a challenging remediation problem. Not only are chlorinated compounds resistant to normal biological degradation, but the fractured bedrock presents difficulties to traditional techniques used for recovery of contaminants and for delivery of amendments or reagents for in-situ remediation. The demonstration was conducted under the U.S. Environmental Protection Agency's Superfund Innovative Technology Evaluation (SITE) program. The SITE program was established to promote the development, demonstration, and use of innovative treatment technologies for the cleanup of Superfund and other hazardous waste sites. This article presents selected results of the demonstration and focuses on understanding the data in light of the fractured bedrock formation. © 2002 Wiley Periodicals, Inc.     

In situ treatment of a dilute chlorinated solvent plume in an acidic aerobic aquifer

In situ bioremediation was selected in the Record of Decision (ROD) as the remedial technology for a 29‐acre dilute, acidic and aerobic, chlorinated solvent plume (principally trichloroethylene [TCE] and 1,1‐dichloroethylene) for a Superfund site located in central New Jersey. Implementation of the remedy at full‐scale began in late 2010, using reductive dechlorination and bioaugmentation, and treatment has continued steadily over the last 9 years. The amendments injected include electron donor and alkaline (bicarbonate) buffer solution and, once anaerobic aquifer conditions became established, a bioaugmentation culture. Amendment injections occurred in multilevel injection wells (IWs), to maintain control over the vertical interval of amendment delivery. The areal coverage of the plume has been reduced by 59% based on the 10 µg/L TCE isocontour and the contaminant mass has been reduced by 79% through the 9 years of treatment. Lessons learned from this project include the need for bioaugmentation in the acidic aquifer and an efficient and effective manner of well construction and amendment injection using multiscreen single casing IWs and packer systems. Additional lessons learned include differences in longevity of the electron donor amendment versus the bicarbonate neutralization additive, and the need for varied amendment delivery techniques (IWs, direct injection, horizontal well installation) in selected lower permeable zones to attain treatment.     

Enhanced anaerobic bioremediation in a DNAPL residual source zone: Test Area North case study

An Interstate Technology and Regulatory Council (ITRC) forum was recently held that focused on case studies in which bioremediation of dense nonaqueous‐phase liquids (DNAPLs) was performed. This first case study, the Test Area North (TAN) site of the Idaho National Engineering and Environmental Laboratory, involves a trichloroethene (TCE) residual source area in a deep, fractured basalt aquifer that has been undergoing enhanced bioremediation since January 1999. Complete dechlorination from TCE to ethene was documented within nine months of operation, and sodium lactate injections were shown to enhance TCE mass transfer from the residual source. Since that time, optimization of injection strategies has maintained efficient dechlorination while demonstrating accelerated cleanup at a lower cost by changing to a whey powder amendment that solubilizes DNAPL. © 2006 Wiley Periodicals, Inc.     

Stimulation of aerobic degradation of chlorinated ethenes in soil by microbial inoculation

Degradation of chlorinated ethenes under aerobic conditions has been reported using a cometabolic pathway. A site in Illinois had shallow contamination and sandy soils, which in combination created aerobic conditions. The aerobic conditions prevented the degradation of chlorinated ethenes by reductive dechlorination. Biodegradation of chloroethenes under aerobic conditions does not occur naturally at all sites; however, it can be enhanced if microorganisms capable of cometabolic degradation are introduced into the soil. In this study, trichloroethene (TCE) removal in the soil was enhanced by the injection of a commercially available microbial inoculum (CL‐OUT® inoculum, CL‐Solutions, Cincinnati, OH) and nutrients and was compared to chlorinated ethene removal in soil that had received nutrients only and soil that had received activated sludge and nutrients. Trichloroethene removal was measured after one week, seven weeks, and eleven weeks. After one week, no significant TCE removal had occurred in any of the test microcosms. After seven weeks, a slight decrease in TCE levels accompanied by an increase in cis‐1,2‐dichloroethene (cis‐1,2‐DCE) was seen in the microcosms that had received CL‐OUT®. After 11 weeks, a marked decrease in TCE levels was observed in the microcosms that had received CL‐OUT®. No significant TCE decrease was observed in any of the other microcosms. These data suggest that organisms capable of aerobic TCE degradation were not present at the site; however, the addition of an inoculum containing such organisms enabled aerobic degradation to occur. © 2008 Wiley Periodicals, Inc.     

Concentration Effects on Competitive Sorption of Trichloroethylene and Tetrachloroethylene to the Roots of Typha latifolia: Implications for Phytomonitoring

Uptake of organic contaminants by plant roots consists of two consecutive steps: sorption to plant roots and entrance into root xylem tissues through epidermal and endodermic membranes. Most research pertaining to phytoremediation assumed that sorption to plant roots is linear and non-competitive. A growing body of evidence, however, is suggesting that sorption to plant roots is nonlinear and competitive. The objective of this study was to examine the concentration effects of chemical constituents on the competitive sorption of trichloroethylene (TCE) and tetrachloroethylene (PCE) to the roots of Typha latifolia. Competitive sorption was clearly demonstrated by the reduced sorption of TCE and PCE in bi-solute systems than in single-solute systems. Concentration is an important factor affecting the extent of competition. In bi-solute systems, the PCE/TCE ratio on root surface approximately reflected the contaminant footprints in solution. The result was attributed to limited high energetically favorable sorption sites on the root surface and similar sorption mechanisms of TCE and PCE. The results hold significant importance for the application of phytomonitoring of organic contaminant mixtures.     

Natural attenuation of chlorinated solvent plumes at Texas dry cleaners

Dry cleaners are the largest users of perchloroethene (PCE) solvents in the United States. Releases from dry cleaners to soil and groundwater, however, remain largely unstudied. This article presents a database of 137 chlorinated solvent plumes at dry cleaners in Texas. The data indicate that PCE plumes are generally shorter in extent than those from industrial sites. Degradation products were observed at more than 80 percent of the sites with groundwater contamination. Calculated attenuation rates are on the order of one‐to‐three‐year half‐lives for PCE and its degradation products. The estimated cleanup timeframe for calculated attenuation rates is < 50 years. More research is needed to understand the presence of organic carbon sources at dry cleaners and its implications for natural attenuation. © 2004 Wiley Periodicals, Inc.