煤场防风抑尘网抑尘效果研究

随着国家环保要求越来越高,火电厂煤场扬尘问题受到越来越多的关注。防风抑尘网作为治理煤场扬尘的有效技术,日益得到广泛的应用。论述了煤场起尘机理、起尘风速及起尘量估算、煤场扬尘预测模式,综合研究了防风抑尘网起尘机理及抑尘效果,提出了起尘风速及起尘量估算推荐公式、煤场扬尘预测推荐模式,并通过数值模拟计算与实测数据,对防风抑尘网抑尘效果进行了分析。     

防风抑尘网设计要点及参数的确定

介绍了堆场起尘、防风抑尘网抑尘的机理和国内外防风抑尘网研究结果,结合实际工程设计的经验,分析了防风抑尘网设计要点和主要参数,提出防风抑尘网设计的意见和建议。     

油田储油罐非甲烷总挥发实验及仿真模拟

针对油田单井拉油罐非密封生产带来的油气泄漏问题,建立小型原油储油罐挥发损耗实验模拟平台,通过气相色谱法探究各因素对其损耗的影响,利用Fluent仿真软件模拟储油罐的泄漏扩散。结果表明:储液温度和有无风环境对储油罐非甲烷总烃(NMHC)挥发影响较大,储液高度和环境温度对其影响较小;仿真模拟无风环境下,储油罐泄漏口短时间内存在油气积聚现象;有风环境下,当风速为1 m/s,油气积聚不明显;随风速增大,扩散浓度场面积不断增大,油品损耗量增大,在风速为5 m/s的环境下,扩散300 s时的浓度场面积相比扩散200 s时较小,但泄漏口处的油气积聚面积增大。     

高氯离子、低COD废水中COD的测定

建立了适用于高氯离子、低COD废水中COD的重铬酸钾测定方法。分别采用甘油、二氯丙醇、β,β′-二氯异丙醚和氯化钙配制模拟高氯废水,考察了氧化剂重铬酸钾溶液浓度、掩蔽剂加入量(以m(HgSO_4)∶m(Cl~-)表示)对测定效果的影响。实验结果表明:以低浓度(0.05 mol/L)重铬酸钾溶液为氧化剂时,测定数据波动范围小,相对误差也低(-1.4%~+0.4%);对于高氯低COD废水的COD测定,当COD大于100 mg/L时按m(HgSO_4)∶m(Cl~-)=10∶1加入硫酸汞掩蔽剂,当COD小于100 mg/L时按m(HgSO_4)∶m(Cl~-)=20∶1加入硫酸汞掩蔽剂,并采用浓度为0.05 mol/L的重铬酸钾溶液作为氧化剂,能较好地消除氯离子对COD测定的干扰,相对误差在5%以内;将优化后的测定条件应用于实际环氧氯丙烷生产废水COD的测定,重现性良好,当m(HgSO_4)∶m(Cl-)分别为10∶1和20∶1时,相对误差分别为+3.3%和+2.9%,COD平均回收率分别为103.4%和102.9%。     

火电厂液氨贮存风险评价中典型事故影响范围计算

对火电厂液氨贮存风险评价中的三类典型事故（化学爆炸、管道泄漏和贮罐整体破裂）影响范围的计算方法进行了探讨。以某火电厂2×1000MW机组为例,当发生化学爆炸事故时,爆炸冲击波损害等级1、2、3、4的影响区域半径分别为78.3、156.6、391.5和1044m;管道泄漏和贮罐整体破裂所引发的中毒事故中,后者对环境的影响较大。若事故发生后10min内得到有效控制,则在F大气稳定度、1.5m/s风速条件下,贮罐整体破裂半致死浓度的影响区域半径（r值）为344.6m,大于管道泄漏r值（205.8m）;若事故发生后不考虑控制措施,则在F大气稳定度、1.5 m/s风速条件下,贮罐整体破裂半致死浓度的影响区域半径r值为561 m。     

磁化水抑垢的研究

通过静态试验研究了Ｃａ＾２＋、Ｍｇ＾２＋的总浓度、碱度、ＰＨ、ＳＯ＾２－４对磁水抑垢效果的影响,得出了应用磁化水抑垢的适宜条件,为磁水器的实际应用提供了依据。     

丙烯酰胺接枝木薯淀粉的合成及橡胶废水的絮凝处理

以丙烯酰胺为单体,过硫酸铵为引发剂,十二烷基磺酸钠为乳化剂,采用乳液聚合法合成丙烯酰胺接枝木薯淀粉(接枝淀粉)。实验结果表明:当m(淀粉)∶m(单体)为1.0∶1.5、合成温度为60℃、引发剂加入量(质量分数)为2.4%时,单体转化率、接枝率和接枝效率分别为74.7%,69.8%,74.9%;当接枝淀粉的加入量为0.35g/L时,絮凝处理后橡胶废水的吸光度由0.164降为0.073,脱色率为55.5%。     

铝碳微电解法降解水中邻苯二甲酸酯

采用铝碳微电解法降解水中邻苯二甲酸酯（PAEs）。首先考察了初始废水pH、铝碳质量比和反应时间对邻苯二甲酸二甲酯（DMP）降解率的影响，然后分别考察了超声波频率、其他金属的添加和H₂O₂加入量对铝碳微电解法降解模拟混合PAEs废水中DMP、邻苯二甲酸二乙酯（DEP）和邻苯二甲酸二丁酯（DBP）的影响。实验结果表明：在初始DMP质量浓度为20 mg/L、初始废水pH为12.0、铝碳质量比为1∶1、反应时间为30 min的条件下，DMP降解率达49.94%;在上述最佳反应条件下处理DMP，DEP，DBP的质量浓度分别为20，10，8 mg/L的模拟混合PAEs废水，当超声波频率为80 kHz时，模拟混合PAEs废水中DMP，DEP，DBP的降解率分别为63.38%，32.75%，32.23%，当铝铁质量比为100∶1时，DMP，DEP，DBP的降解率分别为59.61%，37.39%，31.50%;添加铜和H₂O₂对PAEs的降解有抑制作用。     

自制ZSM-5分子筛对甲苯气体的吸附-脱附性能

考察了自制ZSM-5分子筛对甲苯气体的吸附-脱附性能，并与市售MCM-22分子筛进行了对比实验。实验结果表明:在吸附温度为25℃、进口甲苯质量浓度为840mg/m3、吸附气体流速为0.016m/s、床层高度为15cm的条件下，出口甲苯质量浓度达到0.8mg/m3时的穿透时间为82min，吸附效率为4.26mg/g;在脱附温度为80℃、脱附气体流速为0.016m/s的条件下，脱附35min时出口甲苯质量浓度达到最大，为1220mg/m3。自制ZSM-5分子筛的吸附-脱附性能优于市售MCM-22分子筛。     

微生物燃料电池对苯酚的降解及其产电性能

构建了单室空气阴极微生物燃料电池(MFC),研究了苯酚含量对以苯酚和葡萄糖为底物的MFC产电性能及苯酚去除率的影响。实验结果表明:当CODB(苯酚贡献的COD)为0时,MFC的运行周期为36 h,最大输出电压为560 m V,最大功率密度为489 m W/m2;CODB为1 000 mg/L时,MFC的运行周期为54 h,最大输出电压为436 m V,最大功率密度为98 m W/m2;当CODB为200 mg/L时,MFC的COD去除率、苯酚去除率和库伦效率(CE)均达到最大,分别为89.7%、99.9%和7.2%,同时,MFC的阳极生物膜产生的氧化峰电流最高,表明在葡萄糖-苯酚双底物对微生物的协同作用下,MFC的阳极生物膜氧化性最强;随着CODB的增大,COD去除率、苯酚去除率和CE均逐渐减小,说明苯酚的抑制作用导致微生物活性降低。     

用脉冲电旋风除尘器处理催化剂厂分子筛尾气

介绍了脉冲电旋风除尘器的工作原理及用其处理催化剂分子筛尾气的试验情况。试验结果表明,分子筛尾气很适合脉冲电旋风除尘处理,除尘效果较好,在进气含尘质量浓度为1324．9mg／m^3时,除尘效率达89．4％左右,粉尘驱进速度达0．15～0．17m／s,比常规电除尘技术提高1倍左右。     

氨浸出含锌烟尘制取活性氧化锌

采用氨浸出法处理含锌烟尘,浸出液在微波-超声波联合作用下蒸氨得碱式碳酸锌沉淀,再经煅烧制得活性氧化锌.实验结果表明:在总氨浓度为9.0 mol/L、浸出温度为40 ℃、浸出液初始pH为 11.0～11.5、搅拌转速为400 r/min、浸出剂体积与含锌烟尘质量比为4、浸出时间为60 min的浸出条件下,锌的浸出率为83.3%.浸出液经过两段净化除杂后,在超声波功率50 W、微波辐射(微波功率随温度的设定而自动变化)的联合作用下,使溶液体系恒温90 ℃,进行蒸氨,沉淀得到前驱体碱式碳酸锌,经煅烧,得到平均直径为0.4 μm、晶型为六方晶系、片状的活性氧化锌.     

Local Circulation with Aeolian Dust on the Slopes and Foot Areas of the Tianshan and Kunlun Mountains around the Taklimakan Desert, China

Four automatic weather stations (AWS) were installed on the slopes and foot areas of the Tianshan and Kunlun Mountains along a longitude of 80 degrees east: (1) Taglak 2400 m a.s.l., (2) Aksu 1000 m, (3) Kartash 2800 m, and (4) Qira 1700 m. These two slopes face the Taklimakan Desert. Tagliak lies on the southern slope of Tianshan, and Kartash on the northern slope of Kunlun. The meteorological characteristics of the mountainous regions were investigated using surface data obtained during an intensive observation period (IOP) in spring 2002. It was found that visibility on the slopes decreases in the daytime, and there is no relationship between visibility and wind speed in the mountainous areas. Two snow layers containing dust particles were observed in the snow cover in Taglak during the IOP in spring 2003. These results suggest that a warm air parcel containing aeolian dust climbs over the slopes of the mountainous areas, and dust particles in the mountainous areas are transported from the foot areas.     

铅冶炼烟尘的物性分析及浸出性研究

采用XRF、XRD、激光粒度分析、DTA-TG、FTIR以及SEM-EDS等技术，对某铅冶炼厂烟尘（简称烟尘）进行了物性分析，并采用稀硫酸对烟尘进行了浸出性研究。分析结果表明：烟尘所含主要元素为Pb，Zn，Cd，Cl，S，As;烟尘是氧化物、硫酸盐、硅酸盐、硫化物和砷化物等物质的混合物，主要物相为ZnO，PbO，PbSO₄，CdO，CdS;烟尘颗粒大小不一，形状各异，多呈相互黏结或包裹状。实验结果表明：在ρ（硫酸）=120 g/L、浸出时间30 min、液固比（稀硫酸体积（mL）与烟尘质量（g）之比）20∶1、浸出温度60 ℃的条件下，Pb，Zn，Cd，As，Cl的浸出率分别达到0.16%，98.95%，49.36%，89.12%，99.31%。     

Numerical Simulation of Synoptic Condition on a Severe Sand Dust Storm

By using observational data and MM5, an observational analysisand numerical study was conducted on the synoptic condition of a severe dust storm that was caused by a Mongolian cyclone whichoccurred from 6 to 8 April 2001. Results illustrated thatthe cyclogenesis was due to the isentropic potential vorticity (IPV) advection in the upper troposphere and the terrain modifiedbaroclinicity in the mid-lower troposphere. The Altai-Sayan complex of mountains blocked the lower level cold air and made the isentropic surface sharply steep. When the air slid down along the isentropic surface the increasing of baroclinicity anddecreasing of stability blew up the vertical vorticity development.The formation of the dust storm was a result of a cyclonic cold front passing across the area. The occurrence of this dust stormwas closely related to the strong surface wind, which was accompanied by a cold front passing, rather than the cyclogenesis, itself. Hence, the reason for the pre-front dust storm formulation was the formation of heating convection. Reasons behind the formation of a black storm (visibilitylower than 50 m), which occurred in the mid-north part ofInner Mongolia, lay in several aspects. Firstly, in thisarea the surface wind was strong, a direct result of thedownward transport in mid-lower troposphere. Secondly,the cold front passed over the effected area near sunsetso the air obtained much more surface heating to form adeeper mixed layer (ML). Thirdly, cooperation between thelower level wind and the terrain made the atmosphere inthis area and acquired the maximum advective contributionnecessary to form a deep post-front ML. The sensitivityexperiment revealed that surface heat flux was important to the frontal lifting. In addition, the forcing of surface heating wasalso seen as the primary forcing mechanism of frontogenesis. Meanwhile, removal of the surface heat flux made the atmosphericstratification became stable and the pre-storm ML very shallow,which weakened the strength of the dust storm.     

The Influence of Synoptic-scale Air Flow and Local Circulation on the Dust Layer Height in the North of the Taklimakan Desert

The present study investigates the influences of synoptic-scale air flows and local wind circulations on the dust layer height (DLH) in the Taklimakan Desert, based on lidar observations performed in the north of the desert in March 2003. The DLH fluctuates approximately every three days between 2500 m (above sea level) and 5000 m, including diurnal variations. Meteorological analyses and numerical simulations show that the three-day fluctuation of DLH corresponds with variations in synoptic-scale air flows over the Taklimakan Desert, and the diurnal variations are linked to downdrafts and updrafts that are formed over the north of the desert as part of local circulations. When strong northerly winds prevail in the upper troposphere and a developed valley wind blows toward the Tienshan Mountains in the lower troposphere, the downdrafts strengthen in the middle troposphere over the north of the desert, lowering the DLH to about 2500 m. In contrast, the DLH rises to about 5000 m when the updrafts develop between strong southerly winds in the upper troposphere and a developed mountain wind blowing from the Tienshan Mountains. Simulations for the local circulation behavior without the presence of the Tienshan Mountains demonstrate that the valley and mountain winds on the southern slope of the Tienshan Mountains control the intensity of the downdrafts and updrafts, thereby influencing the DLH over the north of the Taklimakan Desert.     

The effect of dust emissions from open storage piles to particle ambient concentration and human exposure

The current study focus on the determination of dust emissions from piles in open storage yards of a municipal solid waste (MSW) composting site and the subsequent atmospheric dust dispersion. The ISC3-ST (Industrial Source Complex Version 3 – Short Term) model was used for the evaluation of the PM₁₀ ambient concentrations associated with the dispersion of MSW compost dust emissions in air. Dust emission rates were calculated using the United States Environmental Protection Agency proposed dust resuspension formulation from open storage piles using local meteorological data. The dispersion modelling results on the spatial distribution of PM₁₀ source depletion showed that the maximum concentrations were observed at a distance 25–75 m downwind of the piles in the prevailing wind direction. Sensitivity calculations were performed also to reveal the effect of the compost pile height, the friction velocity and the receptor height on the ambient PM₁₀ concentration. It was observed that PM₁₀ concentrations (downwind in the prevailing wind direction) increased with increasing the friction velocity, increasing the pile height (for distances greater than 125 m from the source) and decreasing the receptor height (for distances greater than 125 m from the source). Furthermore, the results of ISC3-ST were analysed with the ExDoM (Exposure Dose Model) human exposure model. The ExDoM is a model for calculating the human exposure and the deposition dose, clearance, and finally retention of aerosol particles in the human respiratory tract (RT). PM₁₀ concentration at the composting site was calculated as the sum of the concentration from compost pile dust resuspension and the background concentration. It was found that the exposure to PM₁₀ and deposited lung dose for an adult Caucasian male who is not working at the composting site is less by 20–74% and 29–84%, respectively, compared to those for a worker exposed to PM concentrations at the composting site.     

铅蓄电池生产企业的清洁生产审核

介绍了某铅蓄电池生产企业按照清洁生产审核程序的7个阶段开展的清洁生产审核工作,分别对企业含铅废气、含铅废水和含铅危险废物污染源进行了排查,采用铅平衡核算、与清洁生产标准进行指标对比等方法查找问题并进行原因分析,提出改进方案。实施清洁生产方案后企业废水产生量为0.10 m3/(kV.A.h)(以生产单位电功率铅蓄电池产生的废水量计),总铅产生量为0.35 g/(kV.A.h),铅尘处理系统除尘效率达98%以上,年减少含铅废酸液产生量50 t,年减排铅尘3.2 kg,年节约成本50万元以上。