Kinetic studies of endosulfan photochemical degradations by ultraviolet light irradiation in aqueous medium

Kinetic studies of endosulfan photochemical degradation in controlled aqueous systems were carried out by ultraviolet light irradiation at λ = 254 nm. The photolysis of (α + β: 2 + 1) endosulfan, α-endosulfan and β-endosulfan were first-order kinetics. The observed rate constants obtained from linear least-squares analysis of the data were 1 × 10^?4 s^?1; 1 × 10^?4 s^?1; and 2 × 10^?5 s^?1, respectively, and the calculated quantum yields (φ) were 1, 1 and 1.6, respectively. Preliminary differential pulse polarographic (DPP) analysis allowed to observe the possible endosulfan photochemical degradation pathway. This degradation route involves the formation of the endosulfan diol, its transformation to endosulfan ether and finally the ether's complete degradation by observing the potential shifts.     

Biodegradation of endosulfan-contaminated soil in a pilot-scale reactor-bioaugmented with mixed bacterial culture

A novel mixed bacterial culture was enriched from an endosulfan (6, 7, 8, 9, 10, 10 - hexachloro-1, 5, 5a, 6, 9, 9a-hexahydro-6, 9-methano-2, 3, 4-benzo (e) dioxathiepin-3-oxide) processing industrial surface soil. The cultures were successful in the degradation of aqueous phase endosulfan in both aerobic and anaerobic conditions. Using the cultures, endosulfan degradation in silty gravel with sand (GM) was examined via pilot scale reactor at an endosulfan concentration of 0.78 +/- 0.01 mg g(- 1) of soil, and optimized moisture content of 40 +/- 1%. During operation, vertical spatial variability in endosulfan degradation was observed within the reactor. At the end of 56 days, maximum endosulfan degradation efficiency of 78 +/- 0.2% and 86.91 +/- 0.2% was observed in the top and bottom portion of the reactor, respectively. Both aerobic and anaerobic conditions were observed within the reactor. However, endosulfan degradation was predominant in anaerobic condition and the total protein concentration in the reactor was declined progressively down the soil depth. Throughout the study, no known intermediate metabolites of endosulfan reported by previous researchers were observed.     

Complete dechlorination of endosulfan and lindane using Mg0/Pd(+4) bimetallic system

A Mg0/Pd(+4) bimetallic system was evaluated to dechlorinate endosulfan and lindane in the aqueous phase. Studies were conducted with endosulfan and lindane separately, with or without acid in a 1:1 (v/v) water:acetone phase. In the absence of any acid, higher degradation of endosulfan and lindane was observed using Mg0/Pd(+4) doses of 10/0.5 and 4/0.1 mg/mL, respectively. Acetone plays an important role in facilitating the dechlorination reaction by increasing the solubilities of pesticides. Dechlorination kinetics for endosulfan and lindane (30 and 50 mg/L [30 and 50 ppm] concentration of each pesticide) were conducted with varying Mg0/Pd(+4) doses, and the time-course profiles were well-fitted into exponential curves. The optimum observed rate constants (k(obs)) for endosulfan and lindane were obtained with Mg0/Pd(+4) doses of 5/0.5 and 4/0.1 mg/mL, respectively. Gas chromatography-mass spectrometry analyses revealed that endosulfan and lindane were dechlorinated completely into their hydrocarbon skeletons-Bicyclo [2,2,1] hepta 2-5 diene and benzene, respectively.     

Biodegradation of endosulfan by Mortieralla sp. strain W8 in soil: Influence of different substrates on biodegradation

To examine the bioremediation potential of Mortierella sp. strain W8 in endosulfan contaminated soil, the fungus was inoculated into sterilized and unsterilized soil spiked with endosulfan. Wheat bran and cane molasses were used as substrates to understand the influence of different organic materials on the degradation of endosulfan in soil. Strain W8 degraded α- and β-endosulfan in both sterilized and unsterilized soil. In unsterilized soil with wheat bran+W8, α- and β- endosulfan were degraded by approximately 80% and 50%, respectively after 28 d incubation against the initial endosulfan concentration (3 mg kg(-1) dw). The corresponding values for α- and β-endosulfan degradation with wheat bran only were 50% and 3%. Endosulfan diol metabolite was detected after 14 d incubation in wheat bran+W8 whereas it was not found with wheat bran only. Production of endosulfan sulfate, the main metabolite of endosulfan, was suppressed with wheat bran+W8 treatment compared with wheat bran only. It was demonstrated that wheat bran is a more suitable substrate for strain W8 than cane molasses. Wheat bran+W8 is a superior fungus and substrate mix for bioremediation in soil contaminated with endosulfan.     

Biodegradation of endosulfan-contaminated soil in a pilot-scale reactor-bioaugmented with mixed bacterial culture

A novel mixed bacterial culture was enriched from an endosulfan (6, 7, 8, 9, 10, 10 – hexachloro-1, 5, 5a, 6, 9, 9a-hexahydro-6, 9-methano-2, 3, 4-benzo (e) dioxathiepin-3-oxide) processing industrial surface soil. The cultures were successful in the degradation of aqueous phase endosulfan in both aerobic and anaerobic conditions. Using the cultures, endosulfan degradation in silty gravel with sand (GM) was examined via pilot scale reactor at an endosulfan concentration of 0.78 ± 0.01 mg g^{? 1} of soil, and optimized moisture content of 40 ± 1%. During operation, vertical spatial variability in endosulfan degradation was observed within the reactor. At the end of 56 days, maximum endosulfan degradation efficiency of 78 ± 0.2% and 86.91 ± 0.2% was observed in the top and bottom portion of the reactor, respectively. Both aerobic and anaerobic conditions were observed within the reactor. However, endosulfan degradation was predominant in anaerobic condition and the total protein concentration in the reactor was declined progressively down the soil depth. Throughout the study, no known intermediate metabolites of endosulfan reported by previous researchers were observed.     

Kinetic assessment of the potassium ferrate(VI) oxidation of antibacterial drug sulfamethoxazole

Sulfamethoxazole (SMX), a worldwide-applied antibacterial drug, was recently found in surface waters and in secondary wastewater effluents, which may result in ecotoxical effects in the environment. Herein, removal of SMX by environmentally-friendly oxidant, potassium ferrate(VI) (K(2)FeO(4)), is sought by studying the kinetics of the reaction between Fe(VI) and SMX as a function of pH (6.93-9.50) and temperature (15-45 degrees C). The rate law for the oxidation of SMX by Fe(VI) is first-order with respect to each reactant. The observed second-order rate constant decreased non-linearly from 1.33+/-0.08 x 10(3) M(-1)s(-1) to 1.33+/-0.10 x 10(0) M(-1)s(-1) with an increase of pH from 7.00 to 9.50. This is related to protonation of Fe(VI) (HFeO(4)(-) <==> H(+) + FeO(4)(2-); pK(a,HFeO(4)) = 7.23) and sulfamethoxazole (SH <==> H(+) + S(-); pK(a,SH)=5.7). The estimated rate constants were k(11)(HFeO(4)(-) + SH) = 3.0 x 10(4) M(-1)s(-1), k(12)(HFeO(4)(-) + S(-)) = 1.7 x 10(2) M(-1)s(-1), and k(13) (FeO(4)(2-) + SH) = 1.2 x 10(0) M(-1)s(-1). The energy of activation at pH 7.0 was found to be 1.86+/-0.04 kJ mol(-1). If excess potassium ferrate(VI) concentration (10 microM) is used than the SMX in water, the half-life of the reaction using a rate constant obtained in our study would be approximately 2 min at pH 7. The reaction rates are pH dependent; thus, so are the half-lives of the reactions. The results suggest that K(2)FeO(4) has the potential to serve as an oxidative treatment chemical for removing SMX in water.     

Photochemical behavior of parathion in the presence of humic acids from different origins

This paper reports the effect of ultraviolet radiation on the degradation of pesticide ethyl parathion in the presence of humic acids. Ethyl parathion was completely degraded in 300 min using an artificial lamp of 7.41 x 10(-10) einstein/s. Humic acid from peat did not influence the photochemical rate (k = 8.92 x 10(-3) min). However, in the presence of aquatic humic acid, the photochemical rate was higher (11.5 x 10(-3) min). The analytical determinations show the presence of p-nitrophenol and aminophenol in the reaction medium during the photochemical experiments. The kinetic of degradation in all experiments obeyed a first-order reaction pattern.     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: a kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO3/TiO2 UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO3 and TiO2 were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO2 and BaTiO3 for the degradation reactions are 3.166 Einstein m(-2) s(-1) and 2.729 Einstein m(-2) s(-1) and catalytic efficiencies are 6.0444 x 10(-7) mg(-2)h(-1)L2 and 5.403 x 10(-7) mg(-2)h(-1)L2, respectively as calculated from experimental results. BaTiO3 exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO2 photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Enrichment and isolation of a mixed bacterial culture for complete mineralization of endosulfan

In the present study, we isolated three novel bacterial species, namely, Staphylococcus sp., Bacillus circulans-I, and Bacillus circulans-II, from contaminated soil collected from the premises of a pesticide manufacturing industry. Batch experiments were conducted using both mixed and pure cultures to assess their potential for the degradation of aqueous endosulfan in aerobic and facultative anaerobic condition. The influence of supplementary carbon (dextrose) source on endosulfan degradation was also examined. After four weeks of incubation, mixed bacterial culture was able to degrade 71.82 +/- 0.2% and 76.04 +/- 0.2% of endosulfan in aerobic and facultative anaerobic conditions, respectively, with an initial endosulfan concentration of 50 mg l(-1). Addition of dextrose to the system amplified the endosulfan degradation efficiency by 13.36 +/- 0.6% in aerobic system and 12.33 +/- 0.6% in facultative anaerobic system. Pure culture studies were carried out to quantify the degradation potential of these individual species. Among the three species, Staphylococcus sp. utilized more beta endosulfan compared to alpha endosulfan in facultative anaerobic system, whereas Bacillus circulans-I and Bacillus circulans-II utilized more alpha endosulfan compared to beta endosulfan in aerobic system. In any of these degradation studies no known intermediate metabolites of endosulfan were observed.     

Different reaction mechanisms of diphenylether and 4-bromodiphenylether with nitrous acid in the 355 nm laser flash photolysis of mixed aqueous solution

The microscopic reaction mechanisms of diphenylether (DPE) and 4-bromodiphenylether (4-BrDPE) with nitrous acid (HNO(2)) in the absence of O(2) have been explored by the 355nm laser flash photolysis. It was proposed that OH radical, from the photolysis of HNO(2), added to DPE forms the C(12)H(10)O-OH adduct while added to 4-BrDPE forms the 4-BrDPE-OH and 4-BrOH-DPE adducts. The first-order decay rate constants of the C(12)H(10)O-OH adduct, 4-BrDPE-OH adduct and 4-BrOH-DPE adduct were measured to be (1.86+/-0.14)x10(5)s(-1), (2.19+/-0.04)x10(5)s(-1) and (1.56+/-0.03)x10(5)s(-1), respectively. The final photolysis products of DPE and HNO(2) identified by GC/MS analysis were phenol, o-hydroxydiphenylether, p-hydroxydiphenylether and p-nitrodiphenylether, while the final photolysis product of 4-BrDPE and HNO(2) identified by LC/MS analysis was mainly the dimer.     

Rapid reductive dechlorination of atrazine by zero-valent iron under acidic conditions

The dechlorination of atrazine (2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine) via reaction with metallic iron under low-oxygen conditions was studied using reaction mixture pH values of 2.0, 3.0, and 3.8. The pH control was achieved through addition of sulfuric acid throughout the duration of the reaction. The lower the pH of the reaction mixture, the faster the degradation of atrazine. The surface area of the sulfuric acid-treated iron particles was 0.31 (+/- 0.01) m2 g-1 and the surface area normalized initial pseudo-first order rate constants (kSA, where rate = kSA x (surface area/l) x [Atrazine]) at pH values of 2.0, 3.0, and 3.8 were equal to, respectively, 3.0 (+/- 0.4) x 10(-3) min-1 m-2 l, 5 (+/- 3) x 10(-4) min-1 m-2 l, and 1 (+/- 1) x 10(-4) min-1 m-2 l. The observed products of the degradation reaction were dechlorinated atrazine (2-ethylamino-4-isopropylamino-1,3,5-triazine) and possibly hydroxyatrazine (2-ethylamino-4-isopropylamino-6-hydroxy-s-triazine). Triazine ring protonation may account, at least in part, for the observed effect of pH on atrazine dechlorination via metallic iron.     

Photochemical behaviour of musk tibetene

BACKGROUND: Synthetic musk compounds are widely used as additives in personal care and household products. The photochemical degradation of musk tibetene in aqueous solutions or in acetonitrile/water mixtures under different conditions was studied in order to assess its environmental fate. METHODS: Musk tibetene dissolved (or suspended) in water and/or acetonitrile/water mixtures was irradiated at different times by UV-light and by solar light. The irradiation mixtures were analyzed by NMR and TLC. The photoproducts formed were identified by GC-MS and NMR data. RESULTS: The experimental results indicated that musk tibetene was photodegradable in water or acetonitrile/water mixtures with half-life reaction times close to 20 minutes. The irradiation mixtures were separated by chromatographic techniques yielding three photoproducts (3,3,5,6,7-pentamethyl-4-nitro-3H-indole, 3,3,5,6,7-pentamethyl-4-nitro-1H-indoline and 3,3,5,6,7-pentamethyl-4-nitro-3H-indolinone) identified by means of spectroscopic analysis. DISCUSSION: The numerical modelling of the photodegradation concentration-time profiles gave (8.13 +/- 0.15) x 10(-2) and (1.34 +/- 0.04) x 10(-2) mol/E for the overall primary quantum yield of direct photolysis for musk tibetene and the major intermediate (3,3,5,6,7-pentamethyl-4-nitro-3H-indolinone), respectively, in the wavelength range 305-366 nm. The half-life times of photodegradation of the both substances varied from 1-1.5 hours at 20 degrees N during the summer season to 6-10 hours for highest latitudes in winter. CONCLUSIONS: Under solar light, musk tibetene was photolabile in acetonitrile and acetonitrile/water 1/1, while it was slowly degraded when suspended in water. In all media, musk tibetene was photodegraded into three photoproducts. By using a kinetic model, the overall primary quantum yields of direct photolysis of musk tibetene and its main photoproduct, in the wavelength range 305-366 nm, were estimated, indicating that the photodegradation rate for musk tibetene is faster than the photolysis rate of the major by-product. RECOMMENDATIONS AND PERSPECTIVES: The results indicate that, in order to assess the environmental impact of musk tibetene on the aquatic ecosystem, great attention should be focused on the major photoproduct which is proved to be more persistent than the parent compound under light irradiation. The predicted half-life times of direct photolysis for both substances ranged from 1-1.5 hours at 20 degrees N during the summer season to about 6-10 hours for highest latitudes in winter, indicating that, from a photochemical point of view, the environmental persistence of these substances increases by increasing the latitudes and during the cold seasons, making more realistic an intake of these xenobiotic molecules into the food chain of aquatic living organisms. Tanabe reports in his Editorial (Tanabe 2005) that "It is necessary to have knowledge of the global picture of synthetic musk pathways. So, it is conceivable that now is the time to study the transport, persistency, distribution, bioaccumulation and toxic potential of this new environmental menace on a global scale, especially in developing countries". Therefore, the future environmental analysis and investigations on the eco-toxicity of nitro musk compounds should take into account not only the presence of the parent compounds but also their photochemical intermediates or end-by-products.     

Photochemical transformation of azoxystrobin in aqueous solutions

The photochemical behaviour of azoxystrobin fungicide (AZX) in water was studied under laboratory conditions. Photodegradation was initiated using a solar simulator (xenon arc lamp) or a jacketed Pyrex reaction cell equipped with a 125 W, high-pressure mercury lamp. HPLC/MS analysis (APCI and ESI in positive and negative modes) was used to identify AZX photoproducts. The calculated polychromatic quantum efficiencies (phi) of AZX at pH 4.5, 7 and 9 were 5.42 x 10(-3), 3.47 x 10(-3) and 3.06 x 10(-3) (degraded molecules per absorbed photon), respectively. The relatively narrow range of values indicates the stability of AZX with respect to photodegradation in the studied pH range. Results from the HPLC/MS analysis suggest that the phototransformation of AZX proceeds via multiple, parallel reaction pathways including: (1) photo-isomerization (E-->Z), (2) photo-hydrolysis of the methyl ester and of the nitrile group, (3) cleavage of the acrylate double bond, (4) photohydrolytic ether cleavage between the aromatic ring giving phenol, and (5) oxidative cleavage of the acrylate double bond.     

Mineralization of C.I. Reactive Yellow 84 in aqueous solution by sonolytic ozonation

The operational parameters and mechanism of mineralization of C.I. Reactive Yellow 84 (RY84), one of the azo dyes, in aqueous solution were investigated using sonolytic ozonation (US/O(3) oxidation). Of the pseudo-first-order degradation rate constants of TOC reduction, 9.0 x 10(-4), 7.3 x 10(-3) and 1.8 x 10(-2)min(-1) were observed with US, O3, and a combination of US and O3, respectively. These results illustrate that ozonation combined with sonolysis for removal of TOC is more efficient than ozonation alone or ultrasonic irradiation alone without considering the operating costs. With the initial pH value at 10.0, the ozone dose at 4.5 g h(-1), the energy density of ultrasound at 176 W l(-1), and the initial concentration of RY84 at 100 mg l(-1), the extent of mineralization measured as TOC loss was maximized. The variation of the concentrations of related ions (oxalate, formate, acetate, NO3(-), NO2(-), NH4(+), Cl(-), and SO4(2-)) during the reaction process was monitored. Other organic intermediates detected by GC/MS were N-methyleneaniline, phthalic acid, 4-hydroxyphthalic acid, isocyanatobenzene, aniline, 4-iminocyclohexa-2,5-dien-1-one, butene diacid and urea. Based on these findings, a tentative degradation pathway was proposed.     

Ozonation of aqueous solution of alpha endosulfan

Ozonation of alpha endosulfan and the effects of some parameters such as pH, temperature and partial pressure on ozonation were investigated and the kinetic constants were calculated in this study. Alpha endosulfan solutions were ozonated in a lab-scale semi-batch reactor under variable experimental conditions. Increase in dissolved ozone concentration had a positive effect on oxidation rate. Alpha endosulfan could be removed up to 94% at pH 4 for an ozonation time of 60 minutes. The oxidation reaction was found to be of second order and of first order with respect to both ozone and alpha endosulfan. The temperature dependent reaction expression of alpha endosulfan was obtained as kd = (1.889 exp(- 2.21 x 10(-3)/T). It was concluded that, although the rate of reaction was lower than the rate of other pesticide oxidation reported in the literature. alpha endosulfan presented an obvious reaction to ozonation.     

Photooxidation of naphthalenesulfonic acids: comparison between processes based on O(3), O(3)/activated carbon and UV/H(2)O(2)

The aim of the present study was to analyze and compare the efficacy of UV photodegradation with that of different advanced oxidation processes (O(3), UV/H(2)O(2), O(3)/activated carbon) in the degradation of naphthalenesulfonic acids from aqueous solution and to investigate the kinetics and the mechanism involved in these processes. Results obtained showed that photodegradation with UV radiation (254 nm) of 1-naphthalenesulfonic, 1,5-naphthalendisulfonic and 1,3,6-naphthalentrisulfonic acids is not effective. Presence of duroquinone and 4-carboxybenzophenone during UV irradiation (308-410 nm) of the naphthalenesulfonic acids increased the photodegradation rate. Addition of H(2)O(2) during irradiation of naphthalenesulfonic acids accelerated their elimination, due to the generation of ()OH radicals in the medium. Comparison between UV photodegradation 254 m and the advanced oxidation processes (O(3), O(3)/activated carbon and UV/H(2)O(2)) showed the low-efficacy of the former in the degradation of these compounds from aqueous medium. Thus, among the systems studied, those based on the use of UV/H(2)O(2) and O(3)/activated carbon were the most effective in the oxidation of these contaminants from the medium. This is because of the high-reactivity of naphthalenesulfonic acids with the *OH radicals generated by these two systems. This was confirmed by the values of the reaction rate constant of *OH radicals with these compounds k(OH), obtained by competitive kinetics (5.7 x 10(9) M(-1) s(-1), 5.2 x 10(9) M(-1) s(-1) and 3.7 x 10(9) M(-1) s(-1) for NS, NDS and NTS, respectively).     

Electrochemical monitoring of methylparathion degradation in an acid aqueous medium in presence of Cu(II)

A study was undertaken to determine the effect of Cu(II) in degradation of methylparathion (o,o-dimethyl o,4-nitrophenyl phosphoriotioate) in acid medium. Initial electrochemical characterization of Cu(II) and methylparathion was done in an aqueous medium at a pH range of 2-7. Cu(II) was studied in the presence of different anions and it was observed that its electroactivity depends on pH and is independent of the anion used. Methylparathion had two reduction signals at pH < or = 6 and only one at pH > 6. The pesticide's transformation kinetic was then studied in the presence of Cu(II) in acid buffered aqueous medium at pH values of 2, 4, and 7. Paranitrophenol appeared as the only electroactive product at all three pH values. The reaction was first order and had k values of 5.2 x 10(-3) s(-1) at pH 2, 5.5 x 10(-3) s(-1) at pH 4 and 9.0 x 10(-3) s(-1) at pH 7. It is concluded that the principal degradation pathway of methylparathion in acid medium is a Cu(II) catalyzed hydrolysis reaction.     

Biodegradation of malathion, α- and β-endosulfan by bacterial strains isolated from agricultural soil in Veracruz,Mexico

The objective of this study was to evaluate the capacity of two bacterial strains isolated, cultivated, and purified from agricultural soils of Veracruz, Mexico, for biodegradation and mineralisation of malathion (diethyl 2-(dimethoxyphosphorothioyl) succinate) and α- and β-endosulfan (6,7,8,9,10,10-hexachloro-1,5,5a,6,9,9a-hexahydro-6-9-methano-2,4,3-benzodioxathiepine-3-oxide). The isolated bacterial strains were identified using biochemical and morphological characterization and the analysis of their 16S rDNA gene, as Enterobacter cloacae strain PMM16 (E1) and E. amnigenus strain XGL214 (M1). The E1 strain was able to degrade endosulfan, whereas the M1 strain was capable of degrading both pesticides. The E1 strain degraded 71.32% of α-endosulfan and 100% of β-endosulfan within 24 days. The absence of metabolites, such as endosulfan sulfate, endosulfan lactone, or endosulfan diol, would suggest degradation of endosulfan isomers through non-oxidative pathways. Malathion was completely eliminated by the M1 strain. The major metabolite was butanedioic acid. There was a time-dependent increase in bacterial biomass, typical of bacterial growth, correlated with the decrease in pesticide concentration. The CO₂ production also increased significantly with the addition of pesticides to the bacterial growth media, demonstrating that, under aerobic conditions, the bacteria utilized endosulfan and malathion as a carbon source. Here, two bacterial strains are shown to metabolize two toxic pesticides into non-toxic intermediates.     

Degradation of aldrin and endosulfan in rotary drum and windrow composting

Removal efficiencies, kinetics and degradation pathways of aldrin, endosulfan α and endosulfan β in vegetable waste were evaluated during rotary drum and conventional windrow composting. The highest percentage removal of aldrin, endosulfan α and endosulfan β in rotary drum composting was 86.8, 83.3 and 85.3% respectively, whereas in windrow composting, it was 66.6%, 77.7% and 67.2% respectively. The rate constant of degradation of aldrin, endosulfan α and endosulfan β during rotary drum composting ranged from 0.410–0.778, 0.057–0.076 and 0.009–0.061 day^?1 respectively. The pathways of degradation of these pesticides in composting process were proposed. Metabolites dieldrin and 1 hydroxychlorodene formed during composting of aldrin in the vegetable waste indicated the occurrence of epoxidation reaction and oxidation of bridge carbon of aldrin containing the methylene group. Formation of chloroendic acid and chloroendic anhydride during composting of endosulfan containing vegetable waste support the occurrence of endosulfan sulfate and dehydration reaction respectively.     

In situ anion diffusion experiments using radiotracers

Diffusion experiments in compacted bentonite have been carried out in situ using the borehole laboratory CHEMLAB. The "ordinary" anion iodide and the redox-sensitive pertechnetate ion have been investigated. In spite of strongly reducing groundwater conditions, technetium was found to diffuse mostly unreduced as TcO4-, although in some spots in the compacted clay, the activity was significantly higher, which may be explained by reduction of some TcO4- by iron-containing minerals in the bentonite. The measured concentration profiles in the clay cannot be accommodated by assuming one single diffusion process. The experimental data are modeled assuming two diffusion paths, intralamellar diffusion and diffusion in external water. The apparent diffusivity for the intralamellar diffusion was found to be 8.6 x 10(-11) m2 s(-1) for iodide with a capacity factor of 0.1, while the apparent diffusivity for the diffusion in external water was found to be 5 x 10(-14) m2 s(-1) with alpha=2.26. The corresponding values for Tc were found to be Da= 6 x 10(-11) m2 s(-1), alpha=0.1 and Da= 1 x 10(-13) m2 s(-1), alpha=0.46, respectively. The diffusion constants and capacity factors obtained in this study are in accordance with data from laboratory experiments.