基于绿色合成法的纳米铁/活性炭复合材料降解阿特拉津的动力学

为了综合处理水中的阿特拉津,以绿茶萃取液为还原剂,以活性炭为载体,采用液相还原法绿色合成了纳米铁/活性炭复合材料,研究了活性炭投放量、阿特拉津的初始浓度、溶液初始pH值及反应时间对阿特拉津去除率的影响,探讨了不同影响因素下阿特拉津的降解动力学。结果表明:阿特拉津降解反应近似符合二级反应动力学,反应速率常数0.001 08~0.002 73 L·(mg·min)~(-1)。在纳米铁/活性炭复合材料去除阿特拉津过程中,纳米铁的还原和活性炭的吸附共同作用。     

旋转盘反应器光催化降解苯酚废水动力学

采用旋转盘反应器(SDR)降解苯酚废水,对苯酚初始浓度、溶液p H值、H2O2的添加对其光催化降解动力学的影响进行了研究。结果表明,SDR内的光催化降解动力学特征符合一级反应动力学规律。苯酚初始浓度越低,反应速率常数k值越大;溶液p H=2时的降解速率高于其他p H值;H2O2的协同作用使苯酚的降解速率明显提高,其速率常数k值为未添加H2O2时的78倍。     

光催化涂料的制备及其降解氟苯

以丙烯酸改性有机硅树脂为粘合剂,聚氨酯为固化剂,制得了室温固化的光催化环保涂料。采用自制的光催化反应器降解氟苯,考察了涂料的光催化活性及降解液初始浓度对反应动力学的影响。结果表明：光催化降解氟苯不是一个简单零级反应,反应表观速率常数与废水初始浓度成正比,反应的表观活化能E为12.5KJ.mol^-1。     

臭氧光催化降解水中甲醛的研究

研究比较了3种光化学方法对水中低浓度甲醛的降解效果,考察了初始pH值、甲醛浓度和臭氧投加速率等因素对臭氧光催化(TiO_2/UV/O_3)降解甲醛的影响。结果表明,紫外臭氧(UV/O_3)、光催化(TiO_2/UV)和TiO_2/UV/O_3对甲醛的降解均符合表观一级反应动力学,TiO_2/UV/O_3降解甲醛的一级表观速率常数大于TiO_2/UV与UV/O_3之和,说明臭氧、光催化有明显的协同作用。pH值对臭氧光催化降解甲醛的速率几乎没有影响;甲醛初始浓度增加,表观反应速率常数下降,但甲醛的绝对去除量仍随初始浓度的增加而显著增加;臭氧投加速率增加,降解速率增加。甲醛降解的主要中间产物为甲酸,但甲酸在臭氧光催化反应过程中也快速降解而被矿化,说明臭氧光催化是一种能安全有效去除甲醛的方法。     

水中腐殖酸可见光降解阿特拉津的动力学研究

探讨了天然水体中存在的腐殖酸(HA)可见光降解水中阿特拉津的动力学特征和影响因素。结果表明,pH对HA可见光降解阿特拉津具有明显影响,水中HA质量浓度为5.0mg/L时,pH为3、5、7、9的条件下,受可见光照6.00h后阿特拉津(初始质量浓度5mg/L)的去除率分别为75.5%、77.3%、91.7%、84.9%,中性条件下阿特拉津可见光降解效果最佳;当HA质量浓度分别为1.5、3.0、5.0、10.0mg/L时,HA对水中阿特拉津的可见光降解均表现为促进作用,且降解过程符合一级反应动力学方程,其一级反应动力学常数分别为0.337 0、0.361 4、0.445 4、0.314 6h-1,HA为5.0mg/L时阿特拉津的可见光降解效果最佳。实际应用中,可以通过优化HA与阿特拉津的浓度比值,发挥HA促进阿特拉津可见光降解的最佳效能。     

太阳能固定膜光催化去除双酚A的特性与效果

以太阳能固定膜光催化中试装置,研究了光解、初始浓度和平均光强等对双酚A(BPA)光催化去除的影响及BPA的矿化和在自来水中的处理效果.试验结果表明,BPA在日光照射下很难光解,其光催化降解呈表观一级反应,在平均光强介于5.7～23.5 W/m2时,表观反应速率常数和平均光强呈线性关系.太阳能光催化对BPA具有良好的矿化作用,但其降解与以UV254为光源的降解有不同的机理.太阳能光催化对自来水中BPA也具有较好的处理效果.     

固定化催化剂TiO2膜光催化降解三氯乙醛的研究

研究了负载于玻璃上的固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果,探讨了TiO2膜光催化降解三氯乙醛的机理,考察了溶液pH值和三氯乙醛初始浓度埘TiO2膜光催化降解三氯乙醛的影响,并研究了固定化催化剂TiO2膜光催化降解三氯乙醛的动力学.结果表明,固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果良好,当三氯乙醛初始浓度为2.25 mg/L时,在紫外光照时间3 h下,三氯乙醛的降解率高达100%.在相司紫外光照时间下,三氯乙醛的光催化降解率随着三氯乙醛初始浓度的增大而下降.在溶液pH=6.5时,三氯乙醛的降解效率最高.固定化催化剂TiO2膜光催化降解三氯乙醛的反应遵循一级反应动力学,反应速率常数随三氯乙醛初始浓度的增大而减小.     

负载型纳米TiO2光催化降解水中微量溶解性间二甲苯

以高压汞灯为光源，采用浸涂-烧结法制备的负载型纳米TiO2作为光催化剂，通过对水中微量溶解性间二甲苯的光催化氧化过程的研究表明，初始浓度在6.68-17.36mg/L的范围内，间二甲苯的光催化反应遵循表观一级反应动力学规律。反应的表观速率常数随溶液初始浓度的增大而减小，半衰期则随初始浓度的增大而增加，经1.5h反应后，溶液中间二甲苯的去除率从17.36mg/L的54.44%增加到6.68mg/L的75.90%。     

壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B动力学研究

采用仿生矿化法制备了壳聚糖/纳米CdS复合颗粒光催化剂,并用于可见光光催化降解猩红B染料模拟废水,研究了猩红B初始浓度、pH、催化剂投加量和催化剂重复使用次数等因素对猩红B光催化降解的影响.X射线衍射(XRD)分析表明,壳聚糖能有效负载CdS纳米微晶.采用Langmuir-Hinshelwood模型描述壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B反应动力学行为,在猩红B初始质量浓度较低(≤20 mg/L)时,光催化降解过程符合假一级动力学方程.降低猩红B初始浓度和溶液pH都可显著增大光催化降解速率常数;催化剂投加量小于0.7 g/L时,光催化降解速率随其增加而增大,但催化剂投加量过大会使光催化降解速率减小;催化剂重复使用第5次时,猩红B光催化降解速率常数仍为第1次使用时的63.4%.     

内循环管式光催化反应器降解水中喹啉的动力学研究

采用内循环管式光催化反应器,考察不同的温度、有机物底物浓度、光照强度、曝气强度等因素对水中喹啉的降解效果影响,在此基础上进行降解动力学研究。实验结果表明:温度、喹啉初始浓度、光照强度、曝气强度等因素与喹啉的催化降解呈现良好的相关关系,喹啉的表观吸附平衡常数为0.0244 L/mg,溶解氧表观吸附平衡常数为2.11,反应活化能为16.734 kJ/mol,光照强度修正指数为0.525。     

Photolysis of atrazine in aqueous solution: role of process variables and reactive oxygen species

Photochemical advanced oxidation processes have been considered for the treatment of water and wastewater containing the herbicide atrazine (ATZ), a possible human carcinogen and endocrine disruptor. In this study, we investigated the effects of the photon emission rate and initial concentration on ATZ photolysis at 254 nm, an issue not usually detailed in literature. Moreover, the role of reactive oxygen species (ROS) is discussed. Photon emission rates in the range 0.87?×?10¹⁸–3.6?×?10¹⁸ photons L^?1 s^?1 and [ATZ]₀?=?5 and 20 mg L^?1 were used. The results showed more than 65 % of ATZ removal after 30 min. ATZ photolysis followed apparent first-order kinetics with k values and percent removals decreasing with increasing herbicide initial concentration. A fivefold linear increase in specific degradation rate constants with photon emission rate was observed. Also, regardless the presence of persistent degradation products, toxicity was efficiently removed after 60-min exposure to UV radiation. Experiments confirmed a noticeable contribution of singlet oxygen and radical species to atrazine degradation during photolysis. These results may help understand the behavior of atrazine in different UV-driven photochemical degradation treatment processes.     

粉煤灰沸石负载Ce3+/TiO2光催化降解水中的菲和荧蒽

以钛酸四丁酯为前驱体，粉煤灰合成沸石为载体，采用溶胶-凝胶方法，在低温条件下制备了稀土铈掺杂的TiO₂光催化剂。利用SEM-EDS、XRD、FTIR对催化剂进行了分析和表征。以高压汞灯为灯源，对多环芳烃菲、荧蒽的降解进行了研究。实验考查了稀土铈掺杂质量分数、催化剂用量、溶液pH、目标物初始质量浓度等因素对光催化降解的影响，研究了其光降解动力学。结果表明，当稀土铈含量为0.5%，催化剂用量为3 g/L，pH偏碱性时，催化效果最佳。光催化反应符合Langmuir-Hinshelwood 动力学规律，菲、荧蒽的降解过程符合一级反应动力学，反应速率常数分别为0.0126 min^-1，0.0099 min^-1。     

Photocatalytic degradation of p,p′-DDT under UV and visible light using interstitial N-doped TiO2

1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (or p,p′-DDT) is one of the most persistent pesticides. It is resistant to breakdown in nature and cause the water contamination problem. In this work, a major objective was to demonstrate the application of N-doped TiO₂ in degradation and mineralization of the p,p′-DDT under UV and visible light in aqueous solution. The N-doped TiO₂ nanopowders were prepared by a simple modified sol–gel procedure using diethanolamine (DEA) as a nitrogen source. The catalyst characteristics were investigated using XRD, SEM, TEM, and XPS. The adsorption and photocatalytic oxidation of p,p′-DDT using the synthesized N-doped TiO₂ under UV and visible light were conducted in a batch photocatalytic experiment. The kinetics and p,p′-DDT degradation performance of the N-doped TiO₂ were evaluated. Results show that the N-doped TiO₂ can degrade p,p′-DDT effectively under both UV and visible lights. The rate constant of the p,p′-DDT degradation under UV light was only 0.0121 min^?1, whereas the rate constant of the p,p′-DDT degradation under visible light was 0.1282 min^?1. Under visible light, the 100% degradation of p,p′-DDT were obtained from N-doped TiO₂ catalyst. The reaction rate of p,p′-DDT degradation using N-doped TiO₂ under visible light was sixfold higher than that under UV light. According to Langmuir-Hinshelwood model, the adsorption equilibrium constant (K) for the N-doped TiO₂ under visible light was 0.03078 L mg^?1, and the apparent reaction rate constant (k) was 1.3941 mg L^?1-min. Major intermediates detected during the p,p′-DDT degradation were p,p′-DDE, o,p′-DDE, p,p′-DDD and p,p′-DDD. Results from this work can be applied further for the breakdown of p,p′-DDT molecule in the real contaminated water using this technology.     

交联壳聚糖/Cu_2O复合颗粒可见光催化脱色活性艳红

利用壳聚糖对金属离子的吸附和螯合作用,通过简单的液相沉淀-还原过程一步原位合成了交联壳聚糖/Cu2O复合粒子。X射线衍射(XRD)和红外(FT-IR)测试结果表明,壳聚糖与Cu2O纳米微粒能有效复合。以活性艳红X-3B溶液为模拟印染废水,采用Langmuir-Hinshelwood假一级方程模拟交联壳聚糖/Cu2O复合粒子光催化脱色反应的动力学行为,从动力学角度系统研究染料初始浓度、反应体系pH、催化剂用量和反应体系气氛等因素对复合粒子可见光催化脱色反应速率的影响。结果表明,当染料溶液浓度较低时,光催化过程可视为假一级反应。降低活性艳红X-3B初始浓度和pH,增加催化剂用量和反应体系的含O2量都可显著增加光解脱色反应速率常数。相同条件下,与纯Cu2O相比,交联壳聚糖/Cu2O复合粒子对X-3B呈现出更好的吸附性和更高的可见光催化活性。     

微波-Fenton对沼液中抗生素和激素的高级氧化

采用微波强化Fenton氧化处理系统,研究H2O2浓度、Fe2+浓度、初始pH、微波辐射时间和微波辐射功率对沼液中喹乙醇、土霉素、四环素及金霉素降解效果的影响.结果发现,采用微波强化Fenton氧化降解沼液中抗生素与激素的最优条件是:H2O2浓度为40 mg/L、Fe2+浓度为12 mg/L、初始pH为4、微波辐射时间为2 min、微波辐射功率为中火(445W),沼液中喹乙醇、土霉素、四环素、金霉素和COD的去除率分别达到67％、93％、91％、88％和46％.在水浴条件下,与单独微波辐射和单独Fenton相比,微波强化Fenton氧化有明显的优越性.     

二氧化钛纳米管光催化降解水中百草枯

二氧化钛纳米管被用于光催化氧化水体中的百草枯,对光催化反应条件、常见Fe3+离子的干扰情况和百草枯光催化降解动力学规律进行了研究。结果表明,浓度为25 mg/L的百草枯溶液,在二氧化钛纳米管(TNT)1.0 g/L,H2O20.5 mL/50 mL,pH=5.0的最优光催化氧化条件下,经过30 min反应可以被100%从水体中去除,表现出非常高的光催化降解效率;动力学方程拟合表明,百草枯光催化氧化反应符合拟一级动力学规律,动力学方程为ln(C0/C)=1.0267t-0.1282,反应速率常数K为1.0267 h-1;双氧水存在时常见的Fe3+能够进一步提高百草枯光催化降解率;该光催化反应体系对低浓度百草枯废水有很好的处理效果,预示着光催化氧化技术适合地表或地下水体中百草枯的去除。     

Carbofuran removal in continuous-photocatalytic reactor: Reactor optimization,rate-constant determination and carbofuran degradation pathway analysis

Carbofuran (CBF) removal in a continuous-flow photocatalytic reactor with granular activated carbon supported titanium dioxide (GAC-TiO₂) catalyst was investigated. The effects of feed flow rate, TiO₂ concentration and addition of supplementary oxidants on CBF removal were investigated. The central composite design (CCD) was used to design the experiments and to estimate the effects of feed flow rate and TiO₂ concentration on CBF removal. The outcome of CCD experiments demonstrated that reactor performance was influenced mainly by feed flow rate compared to TiO₂ concentration. A second-order polynomial model developed based on CCD experiments fitted the experimental data with good correlation (R² ～ 0.964). The addition of 1 mL min^?1 hydrogen peroxide has shown complete CBF degradation and 76% chemical oxygen demand removal under the following operating conditions of CBF ～50 mg L^?1, TiO₂ ～5 mg L^?1 and feed flow rate ～82.5 mL min^?1. Rate constant of the photodegradation process was also calculated by applying the kinetic data in pseudo-first-order kinetics. Four major degradation intermediates of CBF were identified using GC-MS analysis. As a whole, the reactor system and GAC-TiO₂ catalyst used could be constructive in cost-effective CBF removal with no impact to receiving environment through getaway of photocatalyst.     

Degradation of atrazine by catalytic ozonation in the presence of iron scraps: performance,transformation pathway,and acute toxicity

Degradation of atrazine by catalytic ozonation in the presence of iron scraps (ZVI/O₃) was carried out. The key operational parameters (i.e., initial pH, ZVI dosage, and ozone dosage) were optimized by the batch experiments, respectively. This ZVI/O₃ system exhibited much higher degradation efficiency of atrazine than the single ozonation, ZVI, and traditional ZVI/O₂ systems. The result shows that the pseudo-first-order constant (0.0927?min^?1) and TOC removal rate (86.6%) obtained by the ZVI/O₃ process were much higher than those of the three control experiments. In addition, X-ray diffraction (XRD) analysis indicates that slight of γ-FeOOH and Fe₂O₃ were formed on the surface of iron scrap after ZVI/O₃ treatment. These corrosion products exhibit high catalytic ability for ozone decomposition, which could generate more hydroxyl radical (HO^?) to degrade atrazine. Six transformation intermediates were identified by liquid chromatography-mass spectrometry (LC-MS) analysis in ZVI/O₃ system, and the degradation pathway of atrazine was proposed. Toxicity tests based on the inhibition of the luminescence emitted by Photobacterium phosphoreum and Vibrio fischeri indicate the detoxification of atrazine by ZVI/O₃ system. Finally, reused experiments indicate the approving recyclability of iron scraps. Consequently, the ZVI/O₃ system could be as an effective and promising technology for pesticide wastewater treatment.     

陶瓷负载Ag、Ce共掺杂TiO_2光催化剂降解甲基橙的研究

以陶瓷为载体,采用溶胶-凝胶法制备了银离子和铈离子共掺杂TiO2的负载型光催化剂——T-AC/陶瓷,研究了pH值、双氧水用量、催化剂用量、紫外灯强度、废水的初始浓度等因素对T-AC/陶瓷光催化剂降解甲基橙染料废水的影响。结果表明,当pH为2、双氧水用量为0.5 mL/100 mL、催化剂用量为3 g/L、紫外灯功率为20 W、废水初始浓度为10mg/L时,甲基橙的降解率可达85.9%,并且甲基橙的光催化降解属于一级动力学方程,T-AC/陶瓷催化剂有较高的活性和稳定性,在废水处理中具有较好的应用前景。     

Photochemical degradation of atrazine in UV and UV/H2O2 process: pathways and toxic effects of products

The degradation of atrazine in aqueous solution by UV or UV/H₂O₂ processes, and the toxic effects of the degradation products were explored. The mineralization of atrazine was not observed in the UV irradiation process, resulting in the production of hydroxyatrazine (OIET) as the final product. In the UV/H₂O₂ process, the final product was ammeline (OAAT), which was obtained by two different pathways of reaction: dechlorination followed by hydroxylation, and the de-alkylation of atrazine. The by-products of the reaction of dechlorination followed by hydroxylation were OIET and hydroxydeethyl atrazine (OIAT), and those of de-alkylation were deisopropyl atrazine (CEAT), deethyl atrazine (CIAT), and deethyldeisopropyl atrazine (CAAT). OIAT and OAAT appeared to be quite stable in the degradation of atrazine by the UV/H₂O₂ process. In a toxicity test using Daphnia magna, the acute toxic unit (TUa) was less than 1 of TUa (100/EC₅₀, %) in the UV/H₂O₂ process after 30 min of reaction time, while 1.2 to 1.3 of TUa was observed in the UV process. The TUa values of atrazine and the degradation products have the following decreasing order: OIET> Atrazine> CEAT≈CIAT> CAAT. OIAT and OAAT did not show any toxic effects.