Fenton-混凝法处理焦化废水的试验研究

对Fenton预氧化-混凝法联用技术处理焦化废水进行了研究,探讨了Fenton氧化阶段H2O2投加量、混凝阶段pH值以及混凝剂投加量等因素对焦化废水COD去除率的影响,确定了最佳处理条件.结果表明,Fenton预氧化-混凝法处理焦化废水取得了良好效果,COD去除率达97.5%,为该工艺实际处理焦化废水提供了实验依据.     

Fenton-混凝法处理焦化废水的试验研究

对Fenton预氧化-混凝法联用技术处理焦化废水进行了研究，探讨了Fenton氧化阶段H2O2投加量、混凝阶段pH值以及混凝剂投加量等因素对焦化废水COD去除率的影响，确定了最佳处理条件。结果表明，Fenton预氧化一混凝法处理焦化废水取得了良好效果，COD去除率达97．5％，为该工艺实际处理焦化废水提供了实验依据。     

强化3级Fenton氧化结合石灰乳中和混凝处理苯系染料中间体废水

采用多级Fenton氧化结合石灰乳中和混凝对苯系染料中间体废水进行强化处理,考察了Fenton试剂投加级数和投加比例对废水处理效果的影响,以及多级Fenton氧化之间石灰乳中和混凝作用效果,并分析了废水中有机成分的变化趋势。结果表明:Fenton氧化过程中,COD去除率随着Fenton试剂投加级数的增加逐渐增大,3级时效果最佳。3级Fenton处理过程中,Fenton试剂的投加比例为1∶2∶3时,COD去除率最高。在Fenton试剂投加比例为1∶2∶3的3级Fenton氧化过程中,石灰乳可有效调节pH由2.5至4.0,同时其混凝作用也可进一步提高COD去除率,最终COD去除率可达97.20%。经GC-MS对各个过程中有机物的分析鉴定,可发现原废水中的苯系有机物逐渐变化为苯酚、对苯醌以及短链小分子脂肪酸等物质。     

絮凝-Fenton试剂氧化处理印染废水

采用Fenton试剂对某染袜厂2种印染废水(印染红和印染蓝)进行处理。考察了硫酸亚铁投加量、双氧水投加量、反应时间及pH值对印染废水的色度及COD去除率的影响,通过正交实验确定了Fenton试剂处理该废水的最佳操作条件为:反应时间30 min、双氧水(30%)投加量4 mL/L、硫酸亚铁投加量300 mg/L、pH值为4左右。在最佳条件下,印染蓝废水经氧化处理后COD去除率大于80%,色度去除率95%以上;印染红废水需经絮凝预处理后再用Fenton试剂氧化处理,其脱色率达到了99.6%,COD去除率为91.2%,出水COD浓度为96 mg/L,可达标排放。     

可用于去除高盐废水中有机污染物的混凝-Fenton氧化联合工艺

以某环氧树脂生产厂产生的高盐有机废水为对象,对比研究了Fenton、Fenton-混凝、混凝-Fenton等工艺去除废水中有机污染物的效能。考察了Fenton反应中Fe2+、H2O_2投加比、初始pH、反应时间以及混凝反应中混凝剂种类、投加量等参数对处理效果的影响。结果表明:Fenton工艺的最佳条件为亚铁和过氧化氢投加比1∶20,投加量分别为25 mmol·L~(-1)和500 mmol·L~(-1),初始pH 3,反应时间120 min,TOC去除率为62.50%;混凝工艺选择Fe SO_4混凝剂,投加量为300 mg·L~(-1),TOC去除率为23.78%;废水经过Fenton-无混凝剂混凝、Fenton-混凝剂混凝、混凝-一级Fenton氧化和混凝-二级Fenton氧化工艺处理,TOC去除率分别为68.32%、71.51%、80.69%和89.27%。     

强化混凝工艺深度处理给水厂排泥废水

水厂废水的综合处理与回用是我国供水行业的新趋势和节水目标所在,采用强化混凝技术进行水厂排泥废水的深度处理。通过混凝剂筛选实验和有机物表征确定最佳混凝剂为高效聚合铝(HPAC),适宜投加量为650 mg/L。当混凝剂HPAC投加量为650 mg/L时,对COD、TOC、浊度和色度的去除率分别为82.5%、89.8%、95%和92.5%,相应的出水值分别为58 mg/L、8.46 mg/L、2.35 NTU、13度,COD满足《污水综合排放标准》(GB 8978-1996)的要求(COD≤100 mg/L),同时实验结果显示聚合氯化铝(PAC)、HPAC、三氯化铁(FeCl3)主要去除分子量处于>1 300 Da范围的有机物,对分子量处于744～1 300 Da之间的有机物去除有限。     

制浆造纸废水生化出水的混凝处理研究

研究了硫酸铝和三氯化铁对制浆造纸废水生化出水的处理效果.研究发现,不调节原水pH值,硫酸铝投加量为600 mg/L或三氯化铁投加量为300mg/L时,混凝后废水的COD＜150 mg/L,色度＜50倍,出水均符合现阶段排放标准.混凝剂比较发现,在最佳反应条件下,2种混凝剂的处理效果相当,但硫酸铝混凝的成本低于三氯化铁....     

氧化/吸附/混凝协同工艺处理焦化废水生物处理出水的过程及效果分析

针对焦化废水生物处理出水中继续存在多种有机污染物而影响达标及存在安全隐患的现状,基于废水中有机物的物理化学特性,构建了氧化/吸附/混凝的深度处理过程。在NaC lO投加量为40 mg/L,AC投加量为500 mg/L,PFS投加量为300 mg/L,反应时间为0.5 h,以及pH为7.0的最佳条件下,先氧化后吸附混凝,该过程可以实现COD去除率为75%以上,色度去除率80%以上,处理后的水样其COD值与色度值分别下降到60 mg/L及20倍以下;通过GC/MS方法分析处理前后水样中的有机物组分,发现水样中大部分单环芳香族化合物和多环芳香族化合物,部分含氮杂环化学物、有机氯化物以及溴化物被去除,但是,长链烷烃和部分芳香烃继续保留。研究结果证明了氧化/吸附/混凝协同工艺的效果与焦化废水生物出水中有机污染物的分子结构、存在形态形成构效关系,催化作用与氧化作用的协同是获得高效去除率的关键。     

造纸中段废水的混凝-臭氧氧化深度处理研究

就混凝-臭氧氧化组合工艺对造纸中段废水生物处理出水的净化效果进行了研究.结果表明,Ca(OH)2对废水色度、TOC、COD和254 nm的紫外吸收值(UV254)的去除效果均优于聚合氯化铝/聚丙烯酰胺(PAC/PAM);Ca(OH)2-O3组合工艺的处理效果也优于PAC/PAM-O3工艺.当Ca(OH)2投加量为1 g/L、臭氧投加量为50 mg/L时,废水色度降低至10倍以下,COD小于150 mg/L.经Ca(OH)2混凝处理后,相对分子量在0.5～1.0 ku和10.0 ku以上的有机物显著减少;进一步臭氧氧化处理后,除0.5 ～1.0 ku范围的有机物大幅度增加外,其余分子量有机物显著减少.由于对色度贡献很大的大分子量物质的去除,废水的色度显著下降直至无色.     

高浓度钻井废水的混凝-催化氧化处理

以华北油田某深井的高浓度钻井废水(COD高达14 460.0 mg/L)为研究对象,提出了酸化-混凝-催化氧化-吸附的组合处理工艺。重点研制了钻井废水催化氧化处理催化剂(镍基催化剂),通过实验确定了最佳工艺参数条件。着重考察了催化氧化处理的工艺条件,在pH值为4,次氯酸钙投加量为4.4 g/L,催化剂投加量为1.6 g/L的条件下COD降至403.5 mg/L,进一步吸附处理后COD降至139.9 mg/L、色度为30倍、石油类含量为3.8 mg/L、pH为8.0和SS浓度为52mg/L,最终出水水质达到《污水综合排放标准》(GB 8978-1996)二级标准,处理成本为84.8元/m3。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.