The effect of physico-chemical parameters and chemical compounds on the activity of beta-d-galactosidase (B-GAL), a marker enzyme for indicator microorganisms in water

The presence of coliforms in polluted water was determined enzymatically (in situ) by directly monitoring the activity of beta-d-galactosidase (B-GAL) through the hydrolysis of the yellow chromogenic subtrate, chlorophenol red beta-d-galactopyranoside (CPRG), which produced a red chlorophenol red (CPR) product. The objectives of this study were to monitor the effect of compounds commonly found in the environment and used in water treatment on a B-GAL CPRG assay and to investigate the differences between the environmental B-GAL enzyme and the pure commercial enzyme. Environmental B-GAL was optimally active at pH 7.8. Two temperature optima were observed at 35 and 55 degrees C, respectively. B-GAL activity was strongly inhibited by silver and copper ions. While calcium and ferrous ions at lower concentrations (50-100mgl(-1)) increased the enzyme activity, a reduction was observed at higher concentrations (200mgl(-1)). Sodium hypochlorite, normally used in rural areas to disinfect water gradually decreased B-GAL activity at concentrations between 0 and 5600ppm for both the commercial and environmental enzymes. B-GAL from the environment behaved differently from its commercially available counterpart.     

Fenton's pre-treatment of mature landfill leachate

The aim of this study was to check the effectiveness of the Fenton's reagent (Fe2+ + H2O2 + H+) for the pre-treatment of a municipal landfill leachate with the objective of improving its overall biodegradability, evaluated in terms of BOD5/COD ratio, up to a value compatible with biological treatment. The leachate came from a municipal sanitary landfill located in southern Italy and the average values of its main parameters were: pH=8.2; COD=10,540 mgl(-1); BOD5=2,300 mgl(-1); TOC=3,900 mgl(-1); NH4-N=5210 mgl(-1); conductivity=45,350 microScm(-1); alkalinity=21,470 mgl(-1) CaCO3. The effect of initial pH value on the pre-treatment effectiveness was evaluated by titrating the amount of acidic by-products formed. The extent of leachate oxidation was monitored and controlled by both pH and redox potential measurements. The best operational conditions for achieving the desired goal (i.e., BOD5/COD> or =0.5) resulted: Fe2+=275 mgl(-1); H2O2=3,300 mgl(-1); initial pH=3; reaction time=2 h. At the end of the Fenton's pre-treatment, in order to permit a subsequent biological treatment, residual ferric ions were removed increasing the pH up to 8.5 by adding 3 gl(-1) of Ca(OH)2 and 3 mgl(-1) of a cationic polyelectrolyte, the latter as an aid to coagulation. This final step also resulted in a further modest removal of residual COD due to co-precipitation phenomena.     

滇池底泥微生物菌群对微囊藻毒素的生物降解

采用滇池水华蓝藻中提取提纯的微囊藻毒素(microcystins,MCs)作为微生物生长的碳源和氮源,从长期暴露于蓝藻水华的滇池底泥中,通过从含低浓度到高浓度MCs的逐步培养驯化,获得了高效降解MCs的微生物混合菌群,在初始MC-RR和LR浓度大约分别为50 mg/L和30 mg/L下,3 d内可将MCs全部降解.进一步活性研究显示,不同含碳和含氮化合物虽然能够促进混合微生物菌群的生长,但对降解MCs却无明显的促进作用,说明MCs既可以作为微生物生长的碳源,又可以作为微生物生长的氮源,在富含有机物的天然水体中并不一定能够促进微生物对MCs的生物降解.     

Characterization of Cr ion exchange with hydrotalcite

Experiments were performed to characterize the removal of chromium from water with uncalcined hydrotalcite, a clay mineral ion exchange media. The process was characterized as a function of pH, temperature, contact time, and both Cr and hydrotalcite concentrations. A Freundlich isotherm, used to describe adsorption equilibria, was used as a model and Freundlich constants were determined. The kinetics of the ion exchange reaction were also modeled using a pseudo-first order reaction rate. Finally, an equilibrium stage process was modeled with sequential batch separations to determine if hydrotalcite ion exchange could reduce aqueous Cr levels to below the EPA limit of 0.1mgl(-1). It was shown that the process is highly pH dependent, only yielding significant removals at pH levels between 2.0 and 2.1. While hydrotalcite concentration, Cr concentration, and time did effect the ion exchange, temperature was not found to be a factor. Under optimal conditions, maximum removals of greater than 95% were achieved. Finally, sequential batch tests performed on initial Cr solutions ranging from 5mgl(-1) to 40mgl(-1), demonstrated that the water could be purified to a level that was not statistically different than the EPA limit, thus demonstrating the applicability of hydrotalcite ion exchange.     

Comparison of microbial community between two shallow freshwater lakes in middle Yangtze basin, East China

In order to investigate the role of the microbial community in aquatic ecology and nutrient transformations in the development of eutrophication in large shallow freshwater lakes along Yangtze River, the microbial community in the depth-related sediment in Lake Chaohu and Lake Longganhu were compared. Lake Chaohu is one of the three most polluted lakes in China. However, the neighboring Lake Longganhu, a mesotrophic lake, is relatively pristine. The total phosphorous (TP) and total nitrogen (TN) concentration in water was detected at 0.193 mgl(-1) and 3.035 mgl(-1) for Lake Chaohu, 0.051 mgl(-1) and 0.774 mgl(-1) for Lake Longganhu, respectively. The population of the microorganisms with various ecological nutrient transforming functions (e.g. phosphate solubilizing, denitrifying and cellulose decomposing) and a batch of environmental parameters concerning the nutrient accumulating and transforming (e.g. total organic carbon, total nitrogen, and total phosphorous concentrations) were assayed in the depth-related sediment samples from several defined points in both lakes. The sediment samples from Lake Chaohu showed higher density of actinomycetes (P<0.05) and phosphate-solubilizing bacteria (P<0.001) and less profusion of denitrifying bacteria (P<0.05) and cellulolytic microbes (P<0.001), compared with those of Lake Longganhu. The data suggested that the current microbial community in the sediment of Lake Chaohu is in favor of sustaining or further accelerating the process of the lake eutrophication. A possible positive feedback loop which consists of sustained growth of microorganisms and gradual decline of lake eutrophic status is worth further discussing.     

Dissipation of sulfosulfuron in water - bioaccumulation of residues in fish - LC-MS/MS-ESI identification and quantification of metabolites

Dissipation study of sulfosulfuron in natural water and its bioaccumulation in fish was conducted at 25+/-2 degrees C and at two different concentration levels 1mgl(-1) and 2mgl(-1). The dissipation data in water showed the DT50 and DT90 values 67-76 and 222-253 days and followed first order kinetics. Bioaccumulation of sulfosulfuron in fish was conducted under static conditions exposing the fish at one-tenth of sub-lethal concentration 9mgl(-1) and at double the concentration 18mgl(-1), for a period of 56 days. On different occasions fish samples were collected and analyzed. A HPLC-RF method was used for the quantification of sulfosulfuron and aminopyrimidine with the limit of quantification 0.001microg ml(-1). Results showed the accumulation of residues of sulfosulfuron in fish over the concentration range 0.009-0.496microg g(-1). Both in water and fish samples, identified the presence of metabolites aminopyrimidine, desmethyl sulfosulfuron, guanidine, sulfonamide, ethyl sulfone and rearranged amine. The formations of these metabolites are confirmed by LC-MS/MS analysis. An LC-MS/MS electro spray ionization technique was used for this purpose. One of the metabolite Aminopyrimidine was identified at higher concentration levels (0.01-0.1microg ml(-1)) when compared with other metabolites. Subsequently dissipation of aminopyrimidine in water and its bioaccumulation was also studied at the concentration level 1mgl(-1) and 2mgl(-1). The calculated DT50 and DT90 values are 66-68 days and 218-226 days, respectively. This followed first order kinetics. Three hundred days after the exposure complete demineralization was observed.     

Fungal degradation of metsulfuron-methyl in pure cultures and soil

A fungal strain capable of utilizing metsulfuron-methyl as sole carbon and energy sources was isolated from a metsulfuron-methyl treated soil. The degradation characteristics of metsulfuron-methyl by this fungal strain were investigated in liquid culture and soil. More than 79% of metsulfuron-methyl at concentrations of 0.10 mgl(-1), 1.0 mgl(-1) and 10.0 mgl(-1) in pure culture was degraded by strain MD after incubation for 7 days, whereas only 5.6%, 8.6% and 13.1% of metsulfuron-methyl were degraded at levels of 0.10 mgl(-1), 1.0mgl(-1) and 10.0 mgl(-1) in the controls, respectively. The incorporation of strain MD into soil was found to substantially increase the degradation of metsulfuron-methyl. Degradation was 7.5 and 3.8 times faster in strain MD amended soils than in sterilized and fresh soils. The results show that addition of the isolated strain MD enhances degradation of metsulfuron-methyl in water and soil.     

Ozonation of oxytetracycline and toxicological assessment of its oxidation by-products

Antibiotic formulation effluents are well known for their difficult elimination by traditional bio-treatment methods and their important contribution to environmental pollution due to its fluctuating and recalcitrant nature. In the present study the effect of ozonation on the degradation of oxytetracycline (OTC) aqueous solution (100mgl(-1)) at different pH values (3, 7 and 11) was investigated. Ozone (11mgl(-1) corresponds the concentration of ozone in gas phase) was chosen considering its rapid reaction and decomposition rate. The concentration of oxytetracycline, chemical oxygen demand (COD), biochemical oxygen demand (BOD) and BOD5/COD ratio were the parameters to evaluate the efficiency of the ozonation process. In addition, the toxic potential of the OTC degradation was investigated by the bioluminescence test using the LUMIStox 300 instrument and results were expressed as the percentage inhibition of the luminescence of the marine bacteria Vibrio fischeri. The results demonstrate that ozonation as a partial step of a combined treatment concept is a potential technique for biodegradability enhancement of effluents from pharmaceutical industries containing high concentration of oxytetracycline provided that the appropriate ozonation period is selected. At pH 11 and after 60min of ozonation of oxytetracycline aqueous solutions (100 and 200mgl(-1)) the BOD5/COD ratios were 0.69 and 0.52, respectively. It was also shown that COD removal rates increase with increasing pH as a consequence of enhanced ozone decomposition rates at elevated pH values. The results of bioluminescence data indicate that first by-products after partial ozonation (5-30min) of OTC were more toxic than the parent compound.     

Influence of chlorination pH and chlorine dose on the formation of mutagenic activity and the strong bacterial mutagen 3-chloro-4-(dichloromethyl)-5-hydroxy-5(2H)-furanone (MX) in water

Samples from two Dutch raw water sources were chlorinated in the laboratory at different pH:s and chlorine doses, and were analysed for mutagenic activity and the mutagenic compound 3-chloro-4-(dichloromethyl)-5-hydroxy-2(5H)-furanone (MX). Chlorination produced mutagenic activity as well as MX in both waters. The formation of MX was favoured by acidic reaction conditions and high chlorine doses, but in waters treated with excess chlorine at pH 9, no MX was detected. The mutagenicity was approximately on the same level after chlorination of both water types but the MX concentration was significantly higher in the water containing mainly humic material.

MX was found to be quantitatively extracted from acidified waters by the XAD resin adsorption technique.     

The effects of pH on fluoxetine in Japanese medaka (Oryzias latipes): acute toxicity in fish larvae and bioaccumulation in juvenile fish

Recent detection of fluoxetine in the aquatic environment and fish suggests a possibly high accumulation of fluoxetine; however, no report is available on the bioaccumulation of fluoxetine in aquatic organisms. Since bioaccumulation of fluoxetine was probably dependent on pH near the pK(a) value of 10.1, experiments were conducted approximately at pH 7, 8, and 9. Distribution coefficients between 1-octanol and water (D(ow)), and those between synthetic membrane vesicles (liposomes) and water (D(lip-wat)) were determined at pH 7, 8, and 9. The D(ow) and D(lip-wat) values increased significantly with increasing pH. Acute toxicity tests were performed using Japanese medaka (Oryzias latipes) prior to the bioaccumulation test, and 96-h LC(50) values were 5.5, 1.3, and 0.20mgl(-1) at pH 7, 8, and 9, respectively. In the bioaccumulation test, concentrations of fluoxetine and its major metabolite, norfluoxetine, in the fish body and liver were measured. The bioconcentration factors (BCF) of fluoxetine for Japanese medaka were 8.8, 3.0x10, and 2.6x10(2) in the body and 3.3x10(2), 5.8x10(2), and 3.1x10(3) in the liver at pH 7, 8, and 9, respectively. The BCF values were lower at pH 7 and higher at pH 9 mainly because of the increase in nonionized species with significantly higher hydrophobicity than the ionized species at pH values closer to pK(a). A similar trend was obtained for the concentration of norfluoxetine in the fish but the pseudo-BCF values (the ratio of the norfluoxetine concentration in the fish and the fluoxetine concentration in test water) were higher than the BCF value of fluoxetine at all pH conditions.     

Influence of humic substances on the photolysis of aqueous pesticide residues

The present work investigated the direct and indirect photolysis of pesticide residues (atrazine, imazaquin, iprodione), in aqueous solutions and under UV-visible radiation (280-480nm). Different kinds of humic substances (HS) were added to samples in order to evaluate their behaviour as possible photocatalysts and their effect on the photolysis of pesticides. The fulvic acids were purchased from the International Humic Substances Society, and they were added to samples in concentrations ranging from 1 to 150 mgl(-1). Titanium dioxide was used as the photocatalyst, in concentration ranging from 10 to 150 mgl(-1). Pesticides photolysis were measured by UV-visible absorption spectroscopy and differential pulse polarography with all used pesticides, reaching total degradation after 2h of irradiation, thus indicating a fast direct photolysis. Photocatalysis by TiO(2) could increase the pesticides photolysis rate up to 40%. This effect, however, was not observed for imazaquin photolysis. Again, except for imazaquin, HS presence showed a positive effect in increasing pesticide degradation, but only within specific concentration ranges (below 10mg l(-1) for iprodione and about 30mgl(-1) for atrazine). Above these ranges HS induce a decrease in the pesticides photolysis rate. Spin-trapping measurements by electronic paramagnetic resonance spectroscopy, using the spin-trap DMPO, showed that HS are able to photogenerate hydroxyl radicals, increasing the pesticides molecule degradation. However, the HS also react with the photogenerated hydroxyl radical, influencing the pesticide photolysis, leading to a decrease in the photolysis rate and causing it to be strongly dependent on the nature and concentration of residues in the water to be treated.     

Impacts of quicklime (CaO) on the toxicity of copper (CuSO4, 5H2O) to fish and fish food organisms

Static bioassays of 96 h duration were conducted in the laboratory using fry of common carp (Cyprinus carpio), adult tubificid worm (Branchiura sowerbyi) and adult copepod plankton (Cyclops viridis) to determine LC50 values of Cu and CaO to these organisms and effects of interaction between Cu and CaO. Ninety-six hour LC(50) values of Cu to fry of common carp, worm and copepod were found to be 1.40 mgl(-1), 0.08 mgl(-1) and 0.03 mgl(-1) respectively. CaO up to 500 mgl(-1) did not produce any mortality of the fry of common carp up to 96 h. But 96 h LC50 values of CaO to worm and copepod were 83.00 mgl(-1) and 27.80 mgl(-1) respectively. When common carp fry, worm and the copepod were exposed to respective LC50 dose of Cu in presence of varying concentration of CaO, mortality of the organisms significantly reduced and was found inversely correlated with the doses of CaO [y = 48.36-0.807x, r = -0.99 (n = 7) for fish; y = 44.46-0.146x, r = -0.97 (n = 7) for worm; y = 49.46-0.66x, r = -0.99 (n = 7) for the copepod]. The present results indicate that CaO is non-toxic to fish and is capable of reducing the toxicity of Cu to fish while CaO and Cu are antagonistic to each other for the worm and the copepod. Potential of using CaO as antitoxic agent for Cu in water is discussed.     

Chlorination of bisphenol A: kinetics and by-products formation

The kinetics of initial chlorination of bisphenol A (BPA) was studied between pH 2 and 11 at room temperature (20 +/- 2 degrees C). pH Profile of the apparent second-order rate constant of the reaction of BPA with chlorine were modeled considering the elementary reactions of HOCl with BPA species and an acid-catalyzed reaction. The predominant reactions at near neutral pH were the reactions of HOCl with the two phenolate species of BPA (k = 3.10 x 10(4) M(-1)s(-1) for BPA- and 6.62 x 10(4) M(-1) s(-1) for BPA(2-)). At near neutral pH, half-life times of BPA were calculated to be less than 1.5 h for chlorine residual higher than 0.2 mg l(-1). Chlorination of synthetic treated waters spiked with BPA showed that BPA disappeared within 4 h and that chlorinated bisphenol A congeners were rapidly formed and remained in solution for up to 10-20 h when low chlorine dosages are applied (0.5-1 mg l(-1)). To limit their presence in drinking water networks, it is then necessary to maintain high chlorine residuals that rapidly produce and decompose chlorinated bisphenol A congeners.     

Adsorption of microcystins by carbon nanotubes

The production of cyanobacterial toxins microcystins (MCs) by cyanobacterial bloom which may promote the growth of tumor in human liver is a growing environmental problem worldwide. In this paper, the adsorption of MC-RR and LR, which were extracted from cyanobacterial cells in Dianchi Lake in China, by carbon nanotubes (CNTs), wood-based activated carbon (ACs) and clays were investigated. Compared with ACs and clay materials of sepiolite, kaolinite and talc tested, CNTs were found to have a strong ability in the adsorption of MCs. At the concentrations of 21.5 mg l(-1) MC-RR and 9.6 mg l(-1) MC-LR in 50 mmol phosphate buffer solution (pH 7.0), the adsorption amounts of MCs by CNTs with the range of outside diameter from 2 to 10nm were 14.8 and 5.9 mg g(-1), which were about four times higher than those by other adsorbents tested. It was shown that with the decrease of CNTs outside diameters from 60 to 2 nm, the adsorption amount of MCs was apparently increased, however the size of CNTs particles formed in solution declined. This result implies that the size of CNTs tube pore that is fit for the molecular dimension of MCs plays a dominant role. Furthermore the specific surface area of CNTs was also found to be a factor in the adsorption of MCs. The results suggested that the selection of suitable size of CNTs as a kind of adsorbent is very important in the efficient eliminating MCs from drinking water in future.     

Short-term physiological responses to a severe acid stress in three macroinvertebrate species: a comparative study

The present study focuses on the sensitivity among freshwater invertebrate species to acidic stress. Three common macroinvertebrate species in the Vosges Mountains (North-Eastern France), Gammarus fossarum (Amphipoda), Hydropsyche pellucidula (Trichoptera) and Dinocras cephalotes (Plecoptera) were exposed for 24, 72 and 120 h to natural acidified water (pH=4.73+/-0.08, [Ca2+]=39.1+/-0.6 micromol l(-1), [Al(tot)]=28.4+/-1 micromol l(-1)). Short-term exposure to acid stress caused significant decreases both in survival rate and haemolymph ions ([Cl-] and [Na+]). The relative sensitivity to a natural acidic stress slightly differed among the species and was in the following order: G. fossarum, as the most sensitive, then H. pellucidula and D. cephalotes. Results of this study confirm the interest of in situ tests to assess the toxicity of short-term acid exposure. Finally, our results reinforce the hypothesis that transient acidification can offset the recovery of sensitive species of macroinvertebrates in streams chemically recovering from acidification either through liming or declining deposition.     

Removal of arsenic from groundwater by granular titanium dioxide adsorbent

A novel granular titanium dioxide (TiO2) was evaluated for the removal of arsenic from groundwater. Laboratory experiments were carried out to investigate the adsorption capacity of the adsorbent and the effect of anions on arsenic removal. Batch experimental results showed that more arsenate [As(V)] was adsorbed on TiO2 than arsenite [As(III)] in US groundwater at pH 7.0. The adsorption capacities for As(V) and As(III) were 41.4 and 32.4 mgg(-1) TiO2, respectively. However, the adsorbent had a similar adsorption capacity for As(V) and As(III) (approximately 40 mgg(-1)) when simulated Bangladesh groundwater was used. Silica (20 mgl(-1)) and phosphate (5.8 mgl(-1)) had no obvious effect on the removal of As(V) and As(III) by TiO2 at neutral pH. Point-of-entry (POE) filters containing 3 l of the granular adsorbent were tested for the removal of arsenic from groundwater in central New Jersey, USA. Groundwater was continuously passed through the filters at an empty bed contact time (EBCT) of 3 min. Approximately 45,000 bed volumes of groundwater containing an average of 39 microgl(-1) of As(V) was treated by the POE filter before the effluent arsenic concentration increased to 10 microgl(-1). The total treated water volumes per weight of adsorbent were about 60,000 l per 1 kg of adsorbent. The field filtration results demonstrated that the granular TiO2 adsorbent was very effective for the removal of arsenic in groundwater.     

Bioavailability and mass balance studies of a commercial pentabromodiphenyl ether mixture in male Sprague-Dawley rats

Cyanogenic glycosides are common plant toxins. Toxic hydrogen cyanide originating from cyanogenic glycosides may affect soil processes and water quality. In this study, hydrolysis, degradation and sorption of dhurrin (4-hydroxymandelonitrile-beta-d-glucoside) produced by sorghum has been studied in order to assess its fate in soil. The log K(ow) of dhurrin was -1.18+/-0.08 (22 degrees C). Hydrolysis was a first-order reaction with respect to dhurrin and hydroxyl ion concentrations. Half lives ranged from 1.2h (pH 8.6; 25 degrees C) to 530d (pH 4; 25 degrees C). The activation energy of hydrolysis was 112+9kJ. At pH 5.8 and room temperature, addition of humic acids (50gl(-1)) increased the rate of hydrolysis tenfold, while addition of kaolinite or goethite (100-250gl(-1)) both decreased the rate considerably. No significant sorption to soil components could be observed. The degradation rates of dhurrin in top and subsoils of Oxisols, Ultisols, Alfisols and Mollisols were studied at 22 degrees C (25mgl(-1), soil:liquid 1:1 (w:V), pH 3.8-8.1). Half-lives were 0.25-2h for topsoils, and 5-288h in subsoils. Hydrolysis in solution explained up to 45% of the degradation in subsoils whereas the contribution in topsoils was less than 14%, indicating the importance of enzymatic degradation processes. The highest risk of dhurrin leaching will take place when the soil is a low activity acid shallow soil with low content of clay minerals, iron oxides and humic acids.     

Biodegradation of catechol (2-hydroxy phenol) bearing wastewater in an UASB reactor

The present study deals with the biodegradation of catechol through co-metabolism with glucose in aqueous solution as primary substrate in an upflow anaerobic sludge blanket (UASB) reactor. Batch studies indicated that the 1000mgl(-1) glucose concentration was sufficient to cometabolize and degrade catechol in an aqueous solution up to a concentration of 1000mgl(-1). The reactor operated at 35+/-2 degrees C, and at a constant hydraulic retention time of 8h with a gradual stepwise increase in catechol concentration from 100 to 1000mgl(-1) along with glucose as a cosubstrate. The results showed that the catechol was successfully mineralized in an UASB reactor in which microbial granulation was achieved with only glucose as the substrate. The reactor showed > or = 95% COD removal efficiency with 500-1000mgl(-1)catechol concentration in the feed and a glucose concentration of 1500mgl(-1) as a cosubstrate. Similar efficiency was obtained at a constant catechol concentration of 1000mgl(-1) with 500-1000mgl(-1) glucose concentration. Once the reactor got acclimatized with catechol, higher concentrations of catechol can be mineralized with a minimum amount of glucose as the cosubstrate without affecting the performance of the UASB reactor.     

Evaluation of boron removal from water by hydrotalcite-like compounds

Layered double hydroxides (LDHs) or hydrotalcite (HT)-like compounds with different kinds of metal ions (Mg-Al and Mg-Fe) in the brucite-like sheets were prepared and their adsorption properties were studied in the boron removal from aqueous solution under laboratory conditions. The hydrotalcites were synthesized by the coprecipitation method and were characterized by chemical analyses, X-ray diffraction (XRD), Fourier Transform infrared spectroscopy (FTIR) and specific surface area measurements (BET). The affinity of these materials with a mixture of B(OH)(3) and B(OH)(4)(-) was studied as a function of contact time, initial pH of the solutions, HT quantity and B concentration (adsorption isotherms). It was found that 120 min is enough time for the equilibrium state to be reached in boron adsorption. Boron removal was independent of the initial pH of the solutions because of the high buffering capacity of the LDHs. On the other hand, the adsorption capacity increases with increasing the adsorbent quantity. The adsorption isotherms, described by the Langmuir model, are of L-type, suggesting that B(OH)(4)(-) is adsorbed preferentially on HT-like materials. Besides, Mg-Al hydrotalcites showed higher adsorption capacity than Mg-Fe. We proposed that in Mg-Al hydrotalcites, the boron removal occurs by both adsorption on external surface and ion exchange, whereas for Mg-Fe it occurs only by surface adsorption. After treatment of a solution containing 5.2 mgBl(-1) with Mg-Al hydrotalcites the final boron concentration reached the recommended limit by WHO for drinking water (0.5 mgl(-1)).