Determination of selected quaternary ammonium compounds by liquid chromatography with mass spectrometry. Part I. Application to surface, waste and indirect discharge water samples in Austria

A method for simultaneous quantitative determination of alkyl benzyl, dialkyl and trialkyl quaternary ammonium compounds (QACs) has been developed, validated and subsequently applied to real water samples in Austria. The method employs liquid-liquid extraction (LLE) followed by liquid chromatography/tandem mass spectrometry (LC-MS/MS), using electrospray ionization (ESI) in positive mode. The overall method quantification limits range from 4 to 19ng/L for the enrichment of 500mL water samples and analyte recoveries are between 80 and 99%. The method was applied to 62 of the respective water samples without filtration to avoid the loss of the analytes due to the high adsorption capacity of these compounds. Maxima in the mg/L range, especially in the wastewater of hospitals and laundries, could be detected for the selected target compounds.     

A multi-residue method for the analysis of organophosphorus residues in cooked and polished rice using accelerated solvent extraction and dispersive-solid phase extraction (D-SPE) technique and uncertainty measurement

Quick, simple and efficient multi-residue analytical methods were developed and validated for the determination of organophosphorous insecticides from polished and cooked rice. Polished rice was extracted using a simple, automated technique namely accelerated solvent extraction (ASE) using dichloromethane as the extraction solvent. Cooked rice was extracted with acetone and cleaned up using dispersive-solid phase extraction (D-SPE) technique. The single step extraction method adopted for polished rice using accelerated solvent extractor provided satisfactory recovery for eight organophosphorus pesticides (OPPs) which ranged from 85.5–116.7%; 90.0–110.3% and 93.5–118.8% at 1, 5 and 10 limit of quantification (LOQ) levels, respectively. The recovery of cooked rice was in the range of 74–124%; from 75–100% and from 73–87% for 1, 5 and 10 level of fortification, respectively. The total uncertainty was evaluated, taking four main independent sources viz., weighing, purity of the standard, GC calibration curve and repeatability under consideration. The expanded uncertainty was found to be in the range of 5–20%.     

Preconcentration of trace arsenite and arsenate with titanium dioxide nanoparticles and subsequent determination by silver diethyldithiocarbamate spectrophotometric method.

A novel method of preconcentration of trace arsenite and arsenate by using titanium dioxide nanoparticles as adsorbent was described. The concentrations of preconcentrated arsenite and arsenate were determined by a silver diethyldithiocarbamate spectrophotometric method without desorption. Batch adsorption experiments were carried out as a function of the pH, contact time, amount of titanium dioxide nanoparticles, and solution volume. In the pH range 5 to 6, adsorption rates of arsenite and arsenate were higher than 98%. The calibration coefficient was 0.9991, and the linear range was 0 to 100 microg/L. The developed method was precise, with the relative standard deviation <5% at concentration level of 10 microg/L, with a detection limit (3sigma, n=6) of 0.44 microg/L. The accuracy of the method for total arsenic was validated by standard reference materials (SRM 3103a) (National Institute of Standards and Technology, Gaithersburg, Maryland). The method was also applied to the analysis of arsenite and arsenate in natural water samples to verify the accuracy. The recovery values remained in a narrow range, from 95 to 103%.     

Determination of indicator polychlorinated biphenyls (PCBs) by gas chromatography–electron capture detector

An effective method for determination of indicator polychlorinated biphenyls (PCBs) has been validated using gas chromatography (GC) equipped with electron capture detector (ECD). The GC–ECD method was validated by determining the linear range (working range) for determination of the compounds, minimum detectable quantities (MDQ), the precision and accuracy of the method for the analysis of the compounds. MDQ obtained for the compounds ranges from 0.0005 to 0.002 ng. Indeed the method was found to be more sensitive as the number of chlorine atoms attached to the biphenyl increases. The precision and accuracy of the GC method validated ranges from 2.4% to 14.5% and −7.0% to 14.6% respectively. Coefficient of variation associated with the repeatability of the retention times and corresponding peak areas was found to be 0.0001–0.0007 for the retention times and 0.0014–0.059 for the peak areas. Percentage recoveries for the compounds were in the range of 95.7–101.0%. The validated method was then applied to determine levels of indicator PCBs in sediments sampled from eleven sampling points along the Lake Bosuntwi in Ghana and the highest PCB load of 19.17 ng g⁻¹ was recorded at Pipie No. 2. PCB 52 and PCB 101 were found to be the most ubiquitous indicator PCBs in the study area, both with 90.91% occurrence.     

Estimation of plant sampling uncertainty: an example based on chemical analysis of moss samples

In order to estimate the level of uncertainty arising from sampling, 54 samples (primary and duplicate) of the moss species Pleurozium schreberi (Brid.) Mitt. were collected within three forested areas (Wierna Rzeka, Piaski, Posłowice Range) in the Holy Cross Mountains (south-central Poland). During the fieldwork, each primary sample composed of 8 to 10 increments (subsamples) was taken over an area of 10 m² whereas duplicate samples were collected in the same way at a distance of 1–2 m. Subsequently, all samples were triple rinsed with deionized water, dried, milled, and digested (8 mL HNO₃ (1:1) + 1 mL 30 % H₂O₂) in a closed microwave system Multiwave 3000. The prepared solutions were analyzed twice for Cu, Fe, Mn, and Zn using FAAS and GFAAS techniques. All datasets were checked for normality and for normally distributed elements (Cu from Piaski, Zn from Posłowice, Fe, Zn from Wierna Rzeka). The sampling uncertainty was computed with (i) classical ANOVA, (ii) classical RANOVA, (iii) modified RANOVA, and (iv) range statistics. For the remaining elements, the sampling uncertainty was calculated with traditional and/or modified RANOVA (if the amount of outliers did not exceed 10 %) or classical ANOVA after Box-Cox transformation (if the amount of outliers exceeded 10 %). The highest concentrations of all elements were found in moss samples from Piaski, whereas the sampling uncertainty calculated with different statistical methods ranged from 4.1 to 22 %.

     

Trace analysis of parabens preservatives in drinking water treatment sludge,treated, and mineral water samples

Parabens have been widely used as antimicrobial agents, mainly in food products, pharmaceuticals, and cosmetics. Although they are known as safe preservatives, they also cause some harm to human health, which has been discussed lately. Therefore, the aim of this study was to evaluate the occurrence of nine parabens (including isomers) in mineral and drinking waters, besides in drinking water treatment sludge (DWTS) samples with determination by liquid chromatography tandem mass spectrometry (LC-MS/MS). Both methods solid phase extraction (SPE) and QuEChERS were validated. Calibration curves showed a correlation coefficient of 0.99 for all compounds. LOQ values ranged from 0.04 to 4 μg L^?1 in aqueous matrices and from 5 to 500 ng g^?1 in DWTS. Recoveries between 70 and 115% were reached with RSD below 20% for all compounds in SPE whereas recoveries between 62 and 119% were found with RSD below 20% for almost all compounds in QuEChERS. Matrix effect had low values (<?20%); it was only above 20% for methylparaben in the SPE and for pentylparaben in the QuEChERS. Using a quick and simple extraction procedures with SPE, QuEChERS, and LC-MS/MS analyses, these methods proved to be selective and sensitive. They were successfully applied to real samples (treated water, mineral water, and sludge), and methylparaben was detected at concentration levels below 0.242 μg L^?1 in mineral and treated water samples and 10 ng g^?1 in DWTS samples.     

Determination of selected quaternary ammonium compounds by liquid chromatography with mass spectrometry. Part II. Application to sediment and sludge samples in Austria

Soxhlet extraction and high-performance liquid chromatography (HPLC) coupled to tandem mass spectrometry detection (MS/MS) was used for the determination of selected quaternary ammonium compounds (QACs) in solid samples. The method was applied for the determination of alkyl benzyl, dialkyl and trialkyl quaternary ammonium compounds in sediment and sludge samples in Austria. The overall method quantification limits range from 0.6 to 3 microg/kg for sediments and from 2 to 5 microg/kg for sewage sludges. Mean recoveries between 67% and 95% are achieved. In general sediments were especially contaminated by C12 chain benzalkonium chloride (BAC-C12) as well as by the long C-chain dialkyldimethylammonium chloride (DDAC-C18) with a maximum concentration of 3.6 mg/kg and 2.1mg/kg, respectively. Maxima of 27 mg/kg for DDAC-C10, 25 mg/kg for BAC-C12 and 23 mg/kg for BAC-C14 were determined for sludge samples. The sums of the 12 selected target compounds range from 22 mg/kg to 103 mg/kg in the sludge samples.     

Studies of selenium in environmental samples and synthetic mixtures by spectrophotometry

A rapid, highly sensitive and selective spectrophotometric method for the determination of traces of selenium(IV) is described. The method is based on oxidation of p-nitroaniline by selenium(IV) followed by coupling reaction with N-(1-naphthalene-1-yl)ethane-1,2-diamine dihydrochloride (NEDA) in neutral medium to give red colored derivative with lambda(max) 515 nm and is stable for more than 10 days at 35 degrees C. Beer's law is obeyed for selenium(IV) in the concentration range of 0.02-3.2 microg ml(-1) at the wavelength of maximum absorption. The optimum reaction conditions and other analytical parameters were investigated to enhance the sensitivity of the present method. The detailed study of various interferences made the method more selective. The proposed method was successfully applied to the analysis of selenium in polluted water, natural water samples, plant material, soil samples, and synthetic mixtures. The results obtained were agreed with the reported methods at the 95% confidence level. The performance of proposed method was evaluated in terms of Student's t-test and Variance ratio f-test which indicates the significance of proposed method over reported method.     

Rapid determination of residues of pesticides in honey by µGC-ECD and GC-MS/MS: Method validation and estimation of measurement uncertainty according to document No. SANCO/12571/2013

A simple and straightforward method for simultaneous determination of residues of 13 pesticides in honey samples (acrinathrin, bifenthrin, bromopropylate, cyhalothrin-lambda, cypermethrin, chlorfenvinphos, chlorpyrifos, coumaphos, deltamethrin, fluvalinate-tau, malathion, permethrin and tetradifon) from different pesticide classes has been developed and validated. The analytical method provides dissolution of honey in water and an extraction of pesticide residues by n-Hexane followed by clean-up on a Florisil SPE column. The extract was evaporated and taken up by a solution of an injection internal standard (I-IS), ethion, and finally analyzed by capillary gas chromatography with electron capture detection (GC-µECD). Identification for qualitative purpose was conducted by gas chromatography with triple quadrupole mass spectrometer (GC-MS/MS). A matrix-matched calibration curve was performed for quantitative purposes by plotting the area ratio (analyte/I-IS) against concentration using a GC-µECD instrument. According to document No. SANCO/12571/2013, the method was validated by testing the following parameters: linearity, matrix effect, specificity, precision, trueness (bias) and measurement uncertainty. The analytical process was validated analyzing blank honey samples spiked at levels equal to and greater than 0.010 mg/kg (limit of quantification). All parameters were satisfactorily compared with the values established by document No. SANCO/12571/2013. The analytical performance was verified by participating in eight multi-residue proficiency tests organized by BIPEA, obtaining satisfactory z-scores in all 70 determinations. Measurement uncertainty was estimated according to the top-down approaches described in Appendix C of the SANCO document using the within-laboratory reproducibility relative standard deviation combined with laboratory bias using the proficiency test data.     

Rapid determination of dichlorodiphenyltrichloroethane and its main metabolites in aqueous samples by one-step microwave-assisted headspace controlled-temperature liquid-phase microextraction and gas chromatography with electron capture detection

A rapid and sensitive analytical method for the determination of dichlorodiphenyltrichloroethane (DDT) and its main metabolites in environmental aqueous samples has been developed using one-step microwave-assisted headspace controlled-temperature liquid-phase micro-extraction (MA-HS-CT-LPME) technique coupled with gas chromatography-electron-capture detection (GC-ECD). In this study, the one-step extraction of DDT and its main metabolites was achieved by using microwave heating to accelerate the evaporation of analytes into the controlled-temperature headspace to form a cloudy mist vapor zone for LPME sampling. Parameters influencing extraction efficiency were thoroughly optimized, and the best extraction for DDT and its main metabolites from 10-mL aqueous sample at pH 6.0 was achieved by using 1-octanol (4-μL) as the LPME solvent, sampling at 34 °C for 6.5 min under 249 W of microwave irradiation. Under optimum conditions, excellent linear relationship was obtained in the range of 0.05-1.0 μg/L for 1-dichloro-2,2-bis-(p′-chlorophenyl)ethylene (p,p′-DDE), 0.1-2.0 μg/L for o,p′-DDT, 0.15-3.0 μg/L for 1,1-dichloro-2,2-bis-(p′-chlorophenyl)ethane (p,p′-DDD) and p,p′-DDT, with detection limits of 20 ng/L for p,p′-DDE, and 30 ng/L for o,p′-DDT, p,p′-DDD and p,p′-DDT. Precision was in the range of 3.2-11.3% RSD. The proposed method was validated with environmental water samples. The spiked recovery was between 95.5% and 101.3% for agricultural-field water, between 94% and 99.7% for sea water and between 93.5% and 98% for river water. Thus the established method has been proved to be a simple, rapid, sensitive, inexpensive and eco-friendly procedure for the determination of DDT and its main metabolites in environmental water samples.     

Validation of an evacuated canister method for measuring part-per-billion levels of chemical warfare agent simulants

The National Institute for Occupational Safety and Health (NIOSH) research on direct-reading instruments (DRIs) needed an instantaneous sampling method to provide independent confirmation of the concentrations of chemical warfare agent (CWA) simulants. It was determined that evacuated canisters would be the method of choice. There is no method specifically validated for volatile organic compounds (VOCs) in the NIOSH Manual of Analytical Methods. The purpose of this study was to validate an evacuated canister method for sampling seven specific VOCs that can be used as a simulant for CWA agents (cyclohexane) or influence the DRI measurement of CWA agents (acetone, chloroform, methylene chloride, methyl ethyl ketone, hexane, and carbon tetrachloride [CCl4]). The method used 6-L evacuated stainless-steel fused silica-lined canisters to sample the atmosphere containing VOCs. The contents of the canisters were then introduced into an autosampler/preconcentrator using a microscale purge and trap (MPT) method. The MPT method trapped and concentrated the VOCs in the air sample and removed most of the carbon dioxide and water vapor. After preconcentration, the samples were analyzed using a gas chromatograph with a mass selective detector. The method was tested, evaluated, and validated using the NIOSH recommended guidelines. The evaluation consisted of determining the optimum concentration range for the method; the sample stability over 30 days; and the accuracy, precision, and bias of the method. This method meets the NIOSH guidelines for six of the seven compounds (excluding acetone) tested in the range of 2.3-50 parts per billion (ppb), making it suitable for sampling of these VOCs at the ppb level.     

Development of an analytical method for the determination of anthracyclines in hospital effluents

Little is known about the fate of cytostatics after their elimination from humans into the environment. Being often very toxic compounds, their quantification in hospital effluents may be necessary to individualise the putative magnitude of pollution problems. We therefore developed a method for the determination of the very important group of anthracyclines (doxorubicin, epirubicin, and daunorubicin) in hospital effluents. Waste water samples were enriched by solid phase extraction (concentration factor 100), analysed by reversed-phase high performance liquid chromatography (RP-HPLC), and monitored by fluorescence detection. This method is reproducible and accurate within a range of 0.1-5 micro g l(-1) for all compounds (limits of quantification: 0.26-0.29 micro g l(-1) ; recoveries >80%). The applicability of the method was proven by chemical analysis of hospital sewage samples (range: 0.1-1.4 micro g l(-1) epirubicin and 0.1-0.5 micro g l(-1) doxorubicin). Obtained over a time period of one month, the results were in line with those calculated by an input-output model. These investigations show that the examined cytostatics are easily detectable and that the presented method is suitable to estimate the dimension of pharmaceutical contamination originating from hospital effluents.     

Simultaneous determination of estrogenic odorant alkylphenols,chlorophenols, and their derivatives in water using online headspace solid phase microextraction coupled with gas chromatography-mass spectrometry

A simple online headspace solid-phase microextraction (HS-SPME) coupled with the gas chromatography-mass spectrometry (GC-MS) method was developed for simultaneous determination of trace amounts of nine estrogenic odorant alkylphenols and chlorophenols and their derivatives in water samples. The extraction conditions of HS-SPME were optimized including fiber selection, extraction temperature, extraction time, and salt concentration. Results showed that divinylbenzene/Carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fiber was the most appropriate one among the three selected commercial fibers, and the optimal extraction temperature, time, and salt concentration were 70 °C, 30 min, and 0.25 g/mL, respectively. The developed method was validated and showed good linearity (R ²?>?0.989), low limit of detection (LOD, 0.002–0.5 μg/L), and excellent recoveries (76–126 %) with low relative standard deviation (RSD, 0.7–12.9 %). The developed method was finally applied to two surface water samples and some of these target compounds were detected. All these detected compounds were below their odor thresholds, except for 2,4,6-TCAS and 2,4,6-TBAS wherein their concentrations were near their odor thresholds. However, in the two surface water samples, these detected compounds contributed to a certain amount of estrogenicity, which seemed to suggest that more attention should be paid to the issue of estrogenicity rather than to the odor problem.     

EU-wide survey of polar organic persistent pollutants in European river waters

This study provides the first EU-wide reconnaissance of the occurrence of polar organic persistent pollutants in European river waters. More than 100 individual water samples from over 100 European rivers from 27 European Countries were analysed for 35 selected compounds, comprising pharmaceuticals, pesticides, PFOS, PFOA, benzotriazoles, hormones, and endocrine disrupters. Around 40 laboratories participated in this sampling exercise. The most frequently and at the highest concentration levels detected compounds were benzotriazole, caffeine, carbamazepine, tolyltriazole, and nonylphenoxy acetic acid (NPE₁C). Only about 10% of the river water samples analysed could be classified as “very clean” in terms of chemical pollution. The rivers responsible for the major aqueous emissions of PFOS and PFOA from the European Continent could be identified. For the target compounds chosen, we are proposing “indicative warning levels” in surface waters, which are (for most compounds) close to the 90th percentile of all water samples analysed.     

Plant-accelerated dissipation of phenanthrene and pyrene from water in the presence of a nonionic-surfactant

Plant-accelerated dissipation of phenanthrene and pyrene in water in the presence of a nonionic-surfactant (Brij35) was studied. The mechanisms involved were evaluated, based on the investigation of plant uptake of these compounds from water with Brij35. The presence of ryegrass (Lolium multiflorum Lam) clearly enhanced the dissipation of tested PAHs in water with 0-296 mg l(-1) Brij35. The first-order rate constants (K), calculated from the first-order kinetic models for these PAH degradation (all significant at P < 0.05, n=8), of phenanthrene and pyrene in the presence of ryegrass were 16.7-50% and 47.1-108% larger than those of plant-free treatments, whereas half-lives (T1/2) of the former were 14.3-33.4% and 32.0-52.0% smaller than the latter, respectively. However, the promotion of PAH dissipation by ryegrass was found to significantly decrease with increasing Brij35 concentrations. In the range of 0-296 mg l(-1), low concentrations (< or = 74.0 mg l(-1)) of Brij35 generally enhanced plant uptake and accumulation of phenanthrene and pyrene, based on the observed plant concentrations and accumulated amounts of these chemicals from water. In contrast, Brij35 at relatively high concentrations (> or = 148 mg l(-1)) markedly restricted plant uptake of these PAHs. Plant accumulation of phenanthrene and pyrene accounted for 6.21-35.0% and 7.66-24.3% of the dissipation enhancement of these compounds from planted versus unplanted water bodies. In addition, plant metabolism was speculated to be another major mechanism of plant-accelerated dissipation of these PAHs in water systems. Results obtained from this study provided some insight with regard to the feasibility of phytoremediation for PAH contaminated water bodies with coexisted contaminants of surfactants.     

Rapid resolution liquid chromatography-tandem mass spectrometry method for the determination of endocrine disrupting chemicals (EDCs), pharmaceuticals and personal care products (PPCPs) in wastewater irrigated soils

A multiresidue analytical method was developed for the determination of 9 endocrine disrupting chemicals (EDCs) and 19 pharmaceuticals and personal care products (PPCPs) including acidic and neutral pharmaceuticals in water and soil samples using rapid resolution liquid chromatography-tandem mass spectrometry (RRLC-MS/MS). Solid phase extraction (SPE), and ultrasonic extraction combined with silica gel purification were applied as pretreatment methods for water and soil samples, respectively. The extracts of the EDCs and PPCPs in water and soil samples were then analyzed by RRLC-MS/MS in electrospray ionization (ESI) mode in three independent runs. The chromatographic mobile phases consisted of Milli-Q water and acetonitrile for EDCs and neutral pharmaceuticals, and Milli-Q water containing 0.01 % acetic acid (v/v) and acetonitrile: methanol (1:1, v/v) for acidic pharmaceuticals at a flow rate of 0.3 mL/min. Most of the target compounds exhibited signal suppression due to matrix effects. Measures taken to reduce matrix effects included use of isotope-labeled internal standards, and application of matrix-match calibration curves in the RRLC-MS/MS analyses. The limits of quantitation ranged between 0.15 and 14.08 ng/L for water samples and between 0.06 and 10.64 ng/g for solid samples. The recoveries for the target analytes ranged from 62 to 208 % in water samples and 43 to 177 % in solid samples, with majority of the target compounds having recoveries ranging between 70–120 %. Precision, expressed as the relative standard deviation (RSD), was obtained less than 7.6 and 20.5 % for repeatability and reproducibility, respectively. The established method was successfully applied to the water and soil samples from four irrigated plots in Guangzhou. Six compounds namely bisphenol-A, 4-nonylphenol, triclosan, triclocarban, salicylic acid and clofibric acid were detected in the soils.     

Use of semipermeable membrane devices (SPMDs)

Triolein-containing semipermeable membrane devices (SPMDs) were employed as passive samplers to provide data on the bioavailable fraction of organic, waterborne, organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs) and polynuclear aromatic hydrocarbons (PAHs) in streams flowing through a highly polluted industrial area of Bitterfeld in Saxony-Anhalt, Germany. The contamination of the region with organic pollutants originates in wastewater effluents from the chemical industry, from over one-hundred years of lignite exploitation, and from chemical waste dumps. The main objective was to characterise time-integrated levels of dissolved contaminants, to use them for identification of spatial trends of contamination, and their relationship to potential pollution sources. SPMDs were deployed for 43 days in the summer of 1998 at four sampling sites. The total concentration of pollutants at sampling sites was found to range from a low of 0.8 microgram/SPMD to 25 micrograms/SPMD for PAHs, and from 0.4 microgram/SPMD to 22 micrograms/SPMD for OCPs, respectively. None of the selected PCB congeners was present at quantifiable levels at any sampling site. A point source of water pollution with OCPs and PAHs was identified in the river system considering the total contaminant concentrations and the distribution of individual compounds accumulated by SPMDs at different sampling sites. SPMD-data was also used to estimate average ambient water concentrations of the contaminants at each field site and compared with concentrations measured in bulk water extracts. The truly dissolved or bioavailable portion of contaminants at different sampling sites ranged from 4% to 86% for the PAHs, and from 8% to 18% for the OCPs included in the estimation. The fraction of individual compounds found in the freely dissolved form can be attributed to the range of their hydrophobicity. In comparison with liquid/liquid extraction of water samples, the SPMD method is more suitable for an assessment of the background concentrations of hydrophobic organic contaminants because of substantially lower method quantification limits. Moreover, contaminant residues sequestered by the SPMDs represent an estimation of the dissolved or readily bioavailable concentration of hydrophobic contaminants in water, which is not provided by most analytical approaches.     

Development and validation of a method for determination of trace levels of alkylphenols and bisphenol A in atmospheric samples

A method has been developed and validated in order to assess the occurrence of the alkylphenols tert-octylphenol and the isomers of technical nonylphenol as well as bisphenol A in gasphase and aerosol samples of a remote area. Gasphase samples were adsorbed to XAD2 resin, aerosol samples were taken on glass fiber filters. After ultrasonic extraction, clean-up by column chromatography and silylation of the analytes, ten nonylphenol peaks were quantified separately using a GC-MSD-SIM method. The absolute limits of detection and determination are in the range of a few pg per compound, which is a prerequisite for the quantification of the analytes in relatively unpolluted air. The precision of the whole analytical method is in the range of 1-17% and the recoveries range from 57% to 80%. Problems were encountered during method development due to the tendency of the analytes to sorb to glass surfaces. Silanisation of glassware was crucial to achieve acceptable recoveries. The widespread use of the analytes in plastic resins resulted in sample contamination. For this reason a careful choice of sampling material was necessary. Measured concentrations in gasphase samples (lower nanogram per m3 range) and aerosol samples (upper picogram per m3 range) are one to three orders of magnitude below already published concentrations.     

百菌清农药残留的SPE-GC检测

对环境水样中百菌清农药残留进行了SPE-GC分析方法研究。环境水样通过Florisil柱富集、净化,3 mL乙酸乙酯洗脱,GC-ECD进行分析检测。实验表明,百菌清农药残留在0.01~10 mg/L范围内线性关系良好,相关系数为0.9993。外标法定量,检出限为0.0035 mg/L,对实际水样进行加标回收,回收率范围在93.47%~100.14%之间,6次重复测定相对标准偏差在3.97%~4.96%之间,并将方法应用于周边环境地表水的检测。该方法具有简便,快速,准确,灵敏度高等特点,能满足环境水样中农药残留分析要求。