异喹啉季铵盐在盐酸中对A3钢的吸附及其缓蚀作用

采用失重,电化学法研究了异啉季铵盐在1mol/L盐酸溶液中对A3钢的缓蚀行为及吸附规律,实验表明,异喹啉铵盐是一种阴,阳极混合型缓蚀剂,其缓蚀性能优良,在A3钢表面产生化学吸附,吸附过程为放热反应.     

季铵化合物对好氧活性污泥吸附Ni2+的影响研究

以季铵化合物中最具潜在影响力、毒性较大的苄基季铵盐(BAC)为模型物,进行了BAC对好氧活性污泥吸附Ni2+的影响研究.结果表明,当反应液初始pH≤3时,不同浓度的BAC对好氧活性污泥吸附Ni2+的影响较小,当初始pH在3～9时,不同浓度的BAC对Ni2+吸附的抑制影响顺序为100 mg/L＞20 mg/L＞0 mg/...     

改性膨润土联合混凝剂处理微污染水中有机物

采用十二烷基多糖苷季铵盐作为改性剂制备改性膨润土,研究了改性膨润土联合混凝剂去除有机物的效果,考察了有机改性剂用量、微波辐射功率、辐射时间、膨润土投加量、pH值对有机物去除效果的影响,探讨了改性膨润土的改性和去除机理。结果表明,经微波改性后,实现了十二烷基多糖苷季铵盐阳离子对膨润土的插层,增大了层间距,提高了膨润土的吸附性能。联合混凝剂投加改性膨润土能够改善絮凝性能,显著提高有机物的去除效果。在最佳条件下,改性膨润土与PAC联合后的强化混凝,对初始浓度15.3 mg/L的微污染水中有机物的去除率达到95%以上,吸附符合Freundlich吸附等温方程。     

壳聚糖衍生物的合成及其絮凝性能的研究

对从虾蟹壳中制备的壳聚糖进行改性，分别制得壳聚糖衍生物——壳聚糖季铵盐和羧甲基壳聚糖，用于味精废水的絮凝实验。实验结果表明，壳聚糖、壳聚糖季铵盐和羧甲基壳聚糖作为絮凝剂处理味精废水均有较好的效果，以壳聚糖季铵盐的效果最好，其pH值适用范围宽、絮体沉降快，是一种具有良好反应活性的高分子絮凝剂。     

季铵化改性木屑纤维素的制备及对氟离子的吸附研究

以3-氯-2-羟丙基三甲基氯化铵(CTA)为醚化剂,对木屑纤维素进行了季铵化改性.探讨了季铵化改性木屑纤维素用量、pH、吸附温度、氟离子初始浓度和吸附时间对氟离子静态吸附率的影响,以及流速对氟离子动态吸附率的影响.结果表明:(1)静态吸附最佳工艺条件:季铵化改性木屑纤维素用量为3.0 g/L,pH为4.0～6.0,吸附温度为25 ℃,吸附时间为120 min.在此最佳工艺条件下,季铵化改性木屑纤维素对100 mL 50.00 mg/L氟离子溶液的吸附率最高可达90.11%.(2)在pH为5.0、25 ℃的条件下,将50.00 mg/L氟离子溶液以5 mL/min的流速流经装有3.0 g/L季铵化改性木屑纤维素的吸附柱,吸附率可达97.95%.(3)季铵化改性木屑纤维素对溶液中氟离子的吸附过程为放热过程,在吸附过程中存在着化学吸附.(4)木屑来源丰富、价格价廉,季铵化改性木屑纤维素对溶液中氟离子的吸附效果好,且吸附工艺简单、易于实现工业化,具有良好的应用前景.     

CTMAB／SDS改性沸石对水中痕量邻苯二甲酸酯吸附机制

以季铵盐阳离子表面活性剂CTMAB及阴离子表面活性剂SDS对粉末状天然沸石进行复合改性，制备得到了CTMAB／SDS改性沸石。对改性沸石及天然沸石进行红外吸收光谱及XRD衍射表征，并研究了PAEs在天然沸石和CT-MAB／SDS改性沸石上的吸附机制。结果表明，阴阳离子表面活性剂没有对层状结构的键型造成较大的影响；PAEs在天然沸石和CTMAB／SDS改性沸石上的吸附更符合表面吸附一分配作用复合模型；PAEs的表面吸附和分配作用对吸附作用的贡献主要受吸附剂中有机质含量及吸附物质大小、极性及溶解度的影响。     

同分异构体喹啉和异喹啉的缺氧降解性能比较

研究了同分异构体的含氮杂环化合物喹啉和异喹啉在缺氧条件下的降解情况,发现两者表现出不同的缺氧降解特性。喹啉可以在缺氧条件下得到有效降解,其缺氧降解的最佳碳氮比为8。在最佳碳氮比条件下,喹啉的缺氧降解过程符合一级动力学规律,在其降解过程中首先以硝酸盐为电子受体,当硝酸盐氮浓度为零时,亚硝酸盐氮浓度达到最高,此后喹啉的降解主要以亚硝酸盐为电子受体,并和亚硝酸盐氮同时达到最低浓度。异喹啉对硝酸盐的利用甚微,其降解主要表现为厌氧降解特征,降解过程符合零级动力学规律。     

季铵化改性对风化煤腐殖酸水处理性能的影响

对风化煤腐殖酸(HA)进行季铵化改性得到季铵化腐殖酸(QHA),将HA与QHA用作水处理剂,对比两者的阻垢缓蚀性能。结果表明,QHA的阻垢率和缓蚀率均优于HA。QHA、HA投加量分别在20、30 mg/L时阻垢率达到最大值,分别为85.77%、73.50%。HA与QHA的缓蚀率均随投加量的增大而提高,投加量为40mg/L时,QHA的缓蚀率达82.10%,比HA高出22.51百分点。QHA热稳定性能更好,阻垢缓蚀的最佳pH为8～9。QHA具有良好的分散能力和灭藻能力,可在8h内实现高效灭藻。CaCO3垢样的扫描电镜、X射线衍射分析表明,加入QHA使垢体松散,呈碎状分布,晶格结构发生畸变,CaCO3晶面生长的有序度和完整度下降,从而表现出良好的阻垢性能。     

湿法再生吸附剂制备及用于大气CO_2的直接捕集

基于湿法再生吸附技术,利用强碱性季铵盐树脂材料制备了异相吸附剂薄膜,应用于大气中极低CO2的直接分离,以对抗全球变暖。通过滴定法分析吸附剂材料的电荷密度和吸附容量,利用SEM分析不同工况下制备出来的膜材料的表观结构,并对膜材料进行CO2吸附性能的测试。结果发现,热处理能够明显提高膜材料的吸附性能,还研究吸附剂制备对吸附速率,吸附量和机械强度等性能的影响,发现粒径小于43μm的树脂粉末,按60%质量分数制成的500μm厚膜材料具有较优的综合性能。     

共代谢基质对芽孢杆菌Y-4降解异喹啉的影响

以吡啶，葡萄糖和邻苯二甲酸作为共代谢基质，研究了它们对芽孢杆菌Y_4降解异喹啉的影响。实验结果表明各降解过程均遵循二级反应动力学方程：-dS／dt=K2S2＋K1S＋K0。吡啶的加入会抑制异喹啉的降解，并且吡啶的浓度越高，抑制作用越明显。反应体系中葡萄糖的浓度为100-800mg／L时，葡萄糖的加入会促进异喹啉的降解，且葡萄糖浓度越大，异喹啉降解速率P越大，当葡萄糖的浓度为800mg／L时，其降解率速率P可由未加葡萄糖的0．1924h。上升为0．2255h-1。适宜浓度的邻苯二甲酸会对异喹啉的降解产生促进作用，邻苯二甲酸的浓度为50mg／L时，异喹啉的降解速率可由原来的0．1924h-1增加到0．2145h-1，邻苯二甲酸浓度过高反而会抑制异喹啉的降解。     

Efficient adsorption of the mycotoxins zearalenone and T-2 toxin on a modified yeast glucan

1,3-Beta-D-glucan derived from baker's yeast was chemically modified in two steps yielding crosslinked carboxymethyl glucan as the sodium salt (2). After cation exchange with hexadecyltrimethylammonium chloride, a hydrophobic adsorbent (3) was obtained which showed an excellent binding of the estrogenic mycotoxin zearalenone with a maximum adsorption of up to 183 mg/g. Compound 3 additionally showed a relatively high adsorption capacity for the trichothecene T-2 toxin of at least 10 mg/g. Starting from 2, various derivatives were prepared by cation exchange using quaternary ammonium salts bearing substituents besides methyl from four to 18 carbon atoms. The adsorption of T-2 toxin on these derivatives were compared with compound 3 leading to the conclusion that 3 is the best adsorbent of all investigated tetraalkylammonium-modified derivatives of 2.     

季铵化木屑纤维素的制备及其对水中苯酚的吸附性能研究

以3-氯-2-羟丙基三甲基氯化铵(CTA)为醚化剂，对木屑纤维素进行了改性。探讨了改性木屑纤维素用量、pH值、吸附温度、吸附时间和苯酚初始浓度等因素对静态吸附效果的影响。结果表明，木屑纤维素经改性后，对水中的苯酚的吸附过程存在化学吸附，对水中的苯酚的吸附容量得到明显提高。     

Evaluation of Beta‐naphthoxyacetic Acid for Mutagenic Activity in the Salmonella/mammalian Microsome Assay

1,3‐β‐d‐Glucan derived from baker's yeast was chemically modified in two steps yielding crosslinked carboxymethyl glucan as the sodium salt (2). After cation exchange with hexadecyltrimethylammonium chloride, a hydrophobic adsorbent (3) was obtained which showed an excellent binding of the estrogenic mycotoxin zearalenone with a maximum adsorption of up to 183 mg/g. Compound 3 additionally showed a relatively high adsorption capacity for the trichothecene T‐2 toxin of at least 10 mg/g. Starting from 2, various derivatives were prepared by cation exchange using quaternary ammonium salts bearing substituents besides methyl from four to 18 carbon atoms. The adsorption of T‐2 toxin on these derivatives were compared with compound 3 leading to the conclusion that 3 is the best adsorbent of all investigated tetraalkylammonium‐modified derivatives of 2.     

表面活性剂改性4A分子筛对Cr(VI)的吸附行为

采用浸渍法对4A分子筛进行表面改性,通过引入阳离子表面活性剂,使4A分子筛表面附着季铵型阳离子,并与反离子Br-形成"阴离子交换膜",从而促使更多的Cr(VI)阴离子通过离子交换吸附到改性4A分子筛上,通过X-射线衍射(XRD)和傅里叶变换红外光谱(FTIR)对样品的物相结构和组成进行表征分析。研究表明,表面活性剂的类型和疏水碳氢链结构会影响4A分子筛的吸附能力,十八烷基三甲基溴化铵(OTAB)碳氢链长,在分子筛表面形成的双分子层密,对Cr(VI)的吸附量最大。采用准一级、准二级、Elovich和Bangham动力学模型对六价铬的吸附数据进行拟合,其中准一级动力学方程最符合十八烷基三甲基溴化铵改性分子筛的吸附行为。同时,分别从Langmuir和Redlich-Peterson等温吸附模型获得六价铬的最大吸附量为13.98 mg/g,且改性分子筛以均一表面吸附为主。     

Quaternary adsorption equilibria from aqueous systems onto decolourizing activated carbon

An experimental study has been conducted to obtain the adsorption isotherms of four typical pollutants from quaternary aqueous systems onto decolourizing activated carbon. The four materials investigated are: Phenol, 1,4-dihydroxybenzene, 4-amino-l-naphthalene sulfonic acid-sodium salt and Benzoic acid. The study has concentrated on the dilute region of concentrations which range from 10 to 165 ppm (mg/L) at an operating temperature of 30 °C.

The quaternary adsorption equilibria have been modeled using the extended Langmuir predictive model and the ideal adsorbed solution (IAS) theory. In employing these models for the prediction of multicomponent adsorption equilibria, the single-solute isotherms are needed. These isotherms have been fitted to Langmuir, Freundlich, and Dubinin models and the resulting model parameters, which are needed for the prediction of multicomponent adsorption equilibria, are reported. Predictions obtained from the extended Langmuir predictive model and the ideal adsorbed solution (IAS) model are in agreement, however, they deviate to an appreciable extent from experimental observations.     

以磺酸阳离子交换树脂为原料合成含硫水不溶性杀菌剂

设计了一个新的以磺酸阳离子交换树脂为原料制备含硫水不溶性杀菌剂的合成路线，通过聚苯乙烯磺酸吡啶盐中间体合成磺酰氯树脂，在磺酰氯树脂上固载二乙胺，再用带有叔胺基的树脂与卤代烷作用合在含硫的铵盐型聚合物杀菌剂，使用所研制的水不溶性杀菌剂用量2mg/mL时杀菌率达到90％以上。     

Effect of the alkyl chain length on the anaerobic biodegradability and toxicity of quaternary ammonium based surfactants

The anaerobic biodegradability and toxicity to methanogenic gas production of different alkyl chain length homologs of quaternary ammonium based surfactants were examinated. Two series of these cationic surfactants were selected: alkyl trimethyl ammonium and alkyl benzyl dimethyl ammonium compounds. A simple anaerobic gas production test containing municipal digester solids as a source of anaerobic bacteria was used. Under the applied methanogenic conditions, the cationic surfactants tested showed a very poor primary biodegradation and no evidence of any extent of ultimate biodegradation was observed. The toxicity of quaternary ammonium based surfactants to methanogenic gas production decreased with increasing the alkyl chain length.     

天然沸石吸附氨氮的影响因素

对比研究了沸石对生活污水和人工配制氯化铵溶液中氨氮的吸附特性，考察了沸石投加量、反应时间、悬浮物、阳离子和阴离子对沸石吸附氨氮的影响。结果表明，沸石对生活污水中氨氮的吸附能力明显低于人工配制氯化铵溶液，氨氮去除率随着沸石投加量的增加而增加，但单位质量沸石的氨氮吸附量却随之减小，吸附过程呈现快速吸附，缓慢平衡的特点。生活污水中悬浮物的存在，会削减沸石对氨氮的吸附能力。不同类型的阳离子和阴离子的加入都能导致人工配制氯化铵溶液中氨氮在沸石上的吸附量存在差异。阳离子的影响趋势主要为价态的影响，即价态越高，对氨氮吸附阻碍作用越显著，当阳离子当量浓度〉2meq／L时，影响吸附强弱的顺序为Ca2＋〉Mg2＋ 〉Na＋；阴离子影响沸石吸附强弱的顺序受初始氨氮的浓度影响较大。Langmuir等温方程式较Freundich、DubininRadushkevich、KobleCorrigan和Temkin等温方程式更好地描述沸石吸附氨氮的行为。     

Adsorption of ammonium ion by coconut shell-activated carbon from aqueous solution: kinetic, isotherm, and thermodynamic studies

Ammonium ions are one of the most encountered nitrogen species in polluted water bodies. High level of ammonium ion in aqueous solution imparts unpleasant taste and odor problems, which can interfere with the life of aquatics and human population when discharged. Many chemical methods are developed and being used for removal of ammonium ion from aqueous solution. Among various techniques, adsorption was found to be the most feasible and environmentally friendly with the use of natural-activated adsorbents. Hence, in this study, coconut shell-activated carbon (CSAC) was prepared and used for the removal of ammonium ion by adsorption techniques. Ammonium chloride (analytical grade) was purchased from Merck Chemicals for adsorption studies. The CSAC was used to adsorb ammonium ions under stirring at 100 rpm, using orbital shaker in batch experiments. The concentration of ammonium ion was estimated by ammonia distillate, using a Buchi distillation unit. The influence of process parameters such as pH, temperature, and contact time was studied for adsorption of ammonium ion, and kinetic, isotherm models were validated to understand the mechanism of adsorption of ammonium ion by CSAC. Thermodynamic properties such as ?G, ?H, and ?S were determined for the ammonium adsorption, using van't Hoff equation. Further, the adsorption of ammonium ion was confirmed through instrumental analyses such as SEM, XRD, and FTIR. The optimum conditions for the effective adsorption of ammonium ion onto CSAC were found to be pH 9.0, temperature 283 K, and contact time 120 min. The experimental data was best followed by pseudosecond order equation, and the adsorption isotherm model obeyed the Freundlich isotherm. This explains the ammonium ion adsorption onto CSAC which was a multilayer adsorption with intraparticle diffusion. Negative enthalpy confirmed that this adsorption process was exothermic. The instrumental analyses confirmed the adsorption of ammonium ion onto CSAC.