大气颗粒物样品中有机碳和元素碳的测定

采用元素分析仪测定大气颗粒物样品中有机碳、元素碳。应用商业化仪器元素分析仪 ,在燃烧炉温度为 4 50°C时 ,一步测出样品中有机碳的含量 ;再运用加酸的方法除去样品中的碳酸盐 ,然后在燃烧炉温度为 950°C时测出样品中有机碳、元素碳含量之和。通过差减计算 ,得出元素碳的值。有机碳、元素碳测量的标准偏差平均值分别为 0 2 5%、0 50 %。     

燃烧氧化-非分散红外吸收测定水中总有机碳方法的改进

总有机碳测定的方法分为差减法和直接法。现对测定方法进行改进,将差减法和直接法测定结果结合,先将样品进行酸化初步吹扫,再使用差减法测定总有机碳。试验结果显示,无论在标准曲线、精密度试验、加标回收试验还是标准样品测定方面,改进法均优于直接法测定结果,且能较好地缩短测量时间。     

差减法和直接法对水中总有机碳测定结果比较

为了比较差减法和直接法对水中总有机碳测定结果,分别配制差减法和直接法的工作曲线,并分别通过差减法和直接法对不同水体中的总有机碳含量进行测定。比较测定结果,发现差减法和直接法对较清洁水体样品的TOC测定结果误差不大,而对废水样品的TOC测定结果误差较大。     

重庆市春季大气PM10中有机碳、元素碳浓度水平及污染特征分析

2006年4月于重庆市主城区9个采样点和1个城郊对照点同步采集了大气PM10样品,利用热分解示差热导法元素分析仪测定了PM10中的有机碳(OC)、元素碳(EC)的质量浓度,对OC和EC的污染水平、空间分布、OC和EC的浓度关系以及二次有机碳(SOC)等特征进行了较为详细的分析。结果显示,不同区域采样点的OC、EC浓度存在较明显差异,主城区大气环境中OC、EC平均浓度分别为52.5、8.6μg/m3,是对照点OC(16.8μg/m3)、EC(2.9μg/m3)浓度的3.1和3.0倍;主城区总碳气溶胶(TCA)占PM10总浓度的比例均值为33.3%;无论是高污染城区点还是一般城区点,OC和EC浓度间的相关性均不显著;各样点OC/EC值均超过2,表明存在二次有机碳的贡献;初步估算主城区PM10中的二次有机碳浓度均值为39.6μg/m3,占PM10总浓度的16.1%左右。     

东营春季PM10中有机碳和元素碳的污染特征及来源

2010年4月采集了东营市大气PM10样品,测定了PM10的浓度,并采用IMPROVE-TOR方法准确测量了样品中的8个碳组分.结果表明,采样期间,东营市大气PM10的平均浓度为(147.02±56.22) μg/m3；PM10中有机碳(0C)、元素碳(EC)浓度平均值分别为11.82、3.68 μg/m 3；PM10中OC和EC显著相关,表明OC、EC的来源相同；所有采样点PM10中OC/EC均大于2.15,表明存在二次有机碳(SOC)的贡献；PM10中SOC平均质量浓度是3.91 μg/m3,占OC质量浓度的33.08％；通过计算PM10中8个碳组分丰度,初步判断东营市颗粒物中碳的主要来源是汽车尾气、道路扬尘和燃煤.     

南京大气细颗粒中有机碳与元素碳污染特征

为了解南京城区大气细颗粒物中有机碳与元素碳的污染特征,在国控点草场门进行了连续一年的PM2.5采样,分析了有机碳(OC)、元素碳(EC)、ρ(OC)/ρ(EC)污染特征和变化规律。结果表明,采样期间有些PM2.5的日均值超过了《环境空气质量标准》(GB 3095-2012)二级标准,ρ(OC)/ρ(EC)为0.77～4.98,平均值为1.92。PM2.5样品中OC约占18%、EC约占9%。     

广州大气颗粒物中二噁含量的初步研究

2004年夏季在广州四个不同区域采集大气颗粒物样品,参照美国环保局(US EPA)标准方法测定其中二噁的含量,采用热分解光学分析法测定元素碳和有机碳的含量。结果表明,花都、荔湾、天河、黄埔大气颗粒物中二噁浓度(毒性当量)平均值分别为3815fg/m3(104.6fg I-TEQ/m3)、12777fg/m3(430.5fg I-TEQ/m3)、6963fg/m3(163.7fg I-TEQ/m3)、10953fg/m3(769.3fg I-TEQ/m3)。简单地分析了广州大气颗粒物中二噁的含量特征,以及与元素碳、有机碳之间的相关性。     

大气总悬浮颗粒中有机碳的测定

本文提出一种新的高灵敏度测定总悬浮颗粒中有机碳的方法一元素分析法。该方法是在氧化炉最佳温度为６００℃时，一步测定出样品中有机碳的含量，并成功地对齐齐哈尔市大气总悬浮颗粒中的有机碳进行了连续的监测。结果表明，总悬浮颗粒中有机碳的含量有较明显的变化规律。     

碳组分不同监测分析技术的比较

采用在线监测和实验室分析方法,分别在热光透射法(TOT)NIOSH 5040、870升温协议和热光反射法(TOR)IMPROVE-A升温协议下测定PM_2.5中有机碳(OC)、元素碳(EC),并将各测定结果做比对分析。结果表明,在线监测(NIOSH 5040)与实验室分析(IMPROVE-A)结果的相关系数R>0.8,总体相关性较好,EC值差异略大;在线监测与实验室分析在NIOSH 870协议下TC测定值总体相近,OC与EC测定值略有差异;在线监测中NIOSH 5040协议下的OC测定值略低于870协议,EC测定值略高于870协议,日常监测中两种温度协议均可选择。     

ICP-MS法测定水中21种痕量元素

建立了ICP—MS同时测定水中21种痕量元素的方法。对仪器工作参数、测定的同位素、干扰消除方法等进行了研究。21种元素的检出限为0．01～0．9μg·L^-1，相对标准偏差（RSD）为0．33％-4．46％，加标回收率为90％～104％，适合水样中多种元素痕量分析的测定。     

A New Mathematical Approach in Environmental and Life Sciences: Gene–Environment Networks and Their Dynamics

An important research area in life sciences is devoted to modeling, prediction, and dynamics of gene-expression patterns. As clearly understood in these days, this enterprise cannot become satisfactory without acknowledging the role of the environment. To a representation of past, present, and most likely future states, we also encounter measurement errors and uncertainties. This paper surveys and improves recent advances in understanding the foundations and interdisciplinary implications of the newly introduced gene–environment networks, and it integrates the important theme of carbon dioxide emission reduction into the networks and dynamics. We also introduce some operational and managerial issues of practical working and decision making, expressed in terms of sliding windows, quadrants (modules) of parametric effects, and navigating (controlling) between such effects and directing them. Given data from DNA microarray experiments and environmental records, we extract nonlinear ordinary differential equations that contain parameters that have to be determined. For this, we employ modern (Chebychevian) approximation and (generalized semi-infinite) optimization. After this is provided, time- discretized dynamical systems are studied. A combinatorial algorithm with polyhedra sequences allows to detect the region of parametric stability. Finally, we analyze the topological landscape of gene–environment networks with its structural (in)stability. By embedding as a module and investigating CO₂ emission control and figuring out game theoretical aspects, we conclude. This pioneering work is theoretically elaborated, practically devoted to health care, medicine, education, living conditions, and environmental protection, and it invites the readers to future research.      

微波消解-原子吸收光度法测定土壤中铜锌铅镉镍铬

用微波消解－原子吸收光度法测定土壤中铜，锌，铅，镉，镍和铬。通过硝酸－氢氟酸－过氧化氢体系消解液对土壤样品消解，选择出微波最佳消解条件。对硝酸－盐酸－过氧化氢体系消解液和硝酸－氢氟酸－过氧化氢体系消解液进行消解对比试验，发现前者不能将土壤样品完全消解，后者能将样品消解完全，但需将消解液中剩余的酸赶尽，否则测定结果将明显偏低。微波消解土壤与传统电热消解相比，操作简便快速，可提高工作效率。     

Topsoil and Housedust Metal Concentrations in the Vicinity of a Lead Battery Manufacturing Plant

The aim of the study was to determine the extent of heavy metal pollution in the vicinity of a lead battery manufacturing plant in the Czech Republic, both in the general environment and within homes. Topsoils (0–5 cm) were sampled from 100 sites along 4 transects which crossed the battery factory, the town centre and outlying rural areas. Housedust samples were collected from 15 plant-workers' homes and 15 non plant-workers' homes located at various distances from the factory. Samples were analysed for levels of Pb, Zn, Cd, Cu, As and Sb, using ICP-AES. Soil concentrations of Pb, Cd, As and Sb peaked at the perimeter fence of the battery factory with Pb levels of up to 12 650 g g> ^-1. Concentrations of these metals decreased exponentially within 500 m of the plant. Whilst the battery factory does appear to be a source of all the metals with the exception of Zn, emissions do not appear to be transported to any great extent over distances of more than 0.5 km. Topsoil and housedust concentrations of Pb, Zn, Cd, Cu, As and Sb in the general Mlada Boleslav area do not appear to be significantly different from those recorded in a large scale survey of urban soils in the United Kingdom. A comparison of housedust Pb concentrations in homes of plant workers and non-plant workers suggests that there may be a small input of Pb into the home environment by battery plant employees.     

An Overview of Contaminant-Related Issues Identified by Monitoring in San Francisco Bay

The San Francisco Estuary Regional Monitoring Program for Trace Substances (RMP) began in 1993 and is sponsored by 74 local, state, and federal agencies and companies through their discharge or Bay use permits. The RMP monitors water, sediment, toxicity, and bivalve bioaccumulation at 25 sites in the Bay that are considered to represent "background" conditions. Several major environmental issues have been identified by the RMP. Polychlorinated biphenyls and mercury were often above water quality guidelines, and often occurred in fish tissues above U.S. Environmental Protection Agency (U.S. EPA) screening values. Concentrations do not appear to be decreasing, suggesting continuing inputs. Episodes of aquatic toxicity often occurred following runoff events that transport contaminants into the Bay from urbanized and agricultural portions of the watershed. Sediment toxicity occurred throughout the Bay, and has been correlated with concentrations of specific contaminants (chlordanes, polynuclear aromatic hydrocarbons) at some locations; mixtures of contaminants were probably also important. Since the RMP does not monitor all ecosystem components, assessments of the overall condition of the Bay cannot be made. However, in terms of contamination, the RMP samples suggest that the South Bay, and North Bay sites are moderately contaminated.     

Biomagnification factors (fish to Osprey eggs from Willamette River,Oregon, U.S.A.) for PCDDs,PCDFs, PCBs and OC pesticides

A migratory population of 78 pairs of Osprey (Pandion haliaetus) nesting along the Willamette River in westernOregon was studied in 1993. The study was designed to determinecontaminant concentrations in eggs, contaminant concentrationsin fish species predominant in the Ospreys diet, andBiomagnification Factors (BMFs) of contaminants from fish specieseaten to Osprey eggs. Ten Osprey eggs and 25 composite samplesof fish (3 species) were used to evaluate organochlorine (OC)pesticides, polychlorinated biphenyls (PCBs), polychlorinateddibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans(PCDFs). Mercury was also analyzed in fish. Geometric meanresidues in Osprey eggs were judged low, e.g., DDE 2.3 g g^-1 wet weight (ww), PCBs 0.69 g g^-1, 2,3,7,8-TCDD 2.3 ng kg^-1, and generally well below known threshold values for adverse effects on productivity, and the population was increasing. Osprey egg residue data presentedby River Mile (RM) are discussed, e.g., higher PCDDs were generally found immediately downstream of paper mills and eggsfrom the Willamette River had significantly elevated PCBs and PCDDs compared to reference eggs collected nearby in the CascadeMountains. Prey remains at nest sites indicated that the Largescale Sucker (Catostomus macrocheilus) and NorthernPikeminnow (Ptychocheilus oregonensis) accounted for an estimated 90.1% of the biomass in the Osprey diet, and composite samples of these two species were collected from different sampling sites throughout the study area for contaminant analyses. With the large percentage of the fishbiomass in the Osprey diet sampled for contaminants (and fisheaten by Ospreys similar in size to those chemically analyzed),and fish contaminant concentrations weighted by biomass intake, a mean BMF was estimated from fish to Osprey eggs for the largeseries of contaminants. BMFs ranged from no biomagnification(0.42) for 2,3,7,8-TCDF to 174 for OCDD. Our findings for themigratory Osprey were compared to BMFs for the resident HerringGull (Larus argentatus), and differences are discussed. Webelieve a BMF approach provides some basic understanding ofrelationships between contaminant burdens in prey species offish-eating birds and contaminants incorporated into their eggs,and may prove useful in understanding sources of contaminants inmigratory species although additional studies are needed.     

Cyanobacterial Flora from Polluted Marine Shores

Citation of cyanobacterial cultures from the shores of south west coast of Gujarat, India and their relationship with sea water quality, influenced by extensive pollutant runoff is reported in this study. Intensity of pollution was evaluated by physico-chemical analysis of water. Higher load of suspended solids (60–1000 mg l⁻¹) and nutrients (PO₄ ⁻P: 1.3–4 μmole l⁻¹ and NO₃ ⁻N: 12.5–17.8 μmole l⁻¹) were persistent throughout the analysis. Community structure is seen to be influenced by such persistent pollution. Twenty nine cyanobacterial species were isolated belonging to 9 genera of 4 families, with an elevated occurrence of Oscillatoria and Lyngbya species. No heterocystous cyanobacteria were isolated throughout the study.     

An investigation on biological stability of product water generated by lab-scale and pilot-scale distillation systems

Material Disposal Area G is the primary low-levelradioactive waste disposal site at Los Alamos NationalLaboratory, New Mexico, and is adjacent to Pueblo of SanIldefonso lands. Pueblo residents and Los Alamos scientists areconcerned about radiological doses resulting from uptake of AreaG radionuclides by mule deer (Odocoileus hemionus) andRocky Mountain elk (Cervus elaphus), then consumption ofdeer and elk meat by humans. Tissue samples were collected fromdeer and elk accidentally killed near Area G and were analyzedfor ³H, ⁹⁰Sr, total U, ²³⁸Pu, ^{239, 240}Pu,²⁴¹Am, and ¹³⁷Cs. These data were used to estimatehuman doses based on meat consumption of 23 kg y^-1. Humandoses were also modeled using RESRAD, and dose rates to deer andelk were estimated with a screening model. Dose estimates tohumans from tissue consumption were 2.9 × 10^-3 mSv y^-1and 1.6 × 10^-3 mSv y^-1 from deer and elk, respectively,and RESRAD dose estimates were of the same order of magnitude. Estimated dose rates to deer and elk were 2.1 × 10^-4 mGyd^-1 and 4.7 × 10^-4 mGy d^-1, respectively. Allestimated doses were significantly less than established exposurelimits or guidelines.     

The Draft of the New German Guideline VDI 3782/8 to Model Automobile Exhaust Dispersion

The draft of the German guideline to calculate automobile exhaust dispersion is explained. It contains a two-stage-system: For first quick estimates the guideline contains the simple models MLuS and STREET. In case these models are not applicable or their results shows concentration levels close to the air quality standards, the more complex models PROKAS_V and MISKAM are recommended. PROKAS_V is a Gaussian plume model, MISKAM is a 3-dimensional microscale non hydrostatic flow model for built-up areas with an Eulerian dispersion model. The guideline comprises cases in rural areas without or with few adjacent buildings as well as urban areas with buildings near the roads. The contribution gives information about the models, typical results and some of the problems showing up presently.     

Hydrocarbon Utilization in Yeast Isolates Found to Grow in Association with Petroleum in a Polluted Ultisol of Midwestern Nigeria

The population counts of hydrocarbon-utilising yeasts weremonitored at six sampling stations in the Benin City municipalarea over a four-week period. Although the population countswere relatively constant in each locality, the highest countsoccurred in areas heavily polluted by domestic and industrialeffluents. A total of thirty-five hydrocarbon-degrading yeastswere isolated from soil at the sampling stations usingn-hexadecane as sole carbon source. The isolates were identifiedas belonging to the genera Candida (27 strains), Endomycopsis (4 strains). All the organisms grew on long-chainn-alkane, kerosene, diesel oil and crude oil but failed to growon short-chain n-alkane, aromatic and alicyclic hydrocarbons.Measurement of growth attributes of the isolates usingn-hexadecane, diesel oil and crude oil as substrates showed thatthe Candida species were better utilizers of hydrocarbonsubstrates relative to Endomycopsis and Schizosaccharomyces species.     

Hydrologic–Economic Model for Managing Irrigation Intensity in Irrigation Areas under Watertable and Soil Salinity Targets

This paper gives mathematical details and sample applications of SWAGMAN Farm (SWAGMAN, Salt Water and Groundwater Management), a farm-scale hydrologic economic model that integrates agronomic, climatic, irrigation, hydrogeological and economic aspects of irrigated agriculture. The model is capable of determining optimum mix of land use to keep watertable and soil salinity within acceptable limits while maximising the economic returns. Alternatively, the model can simulate water and salt balance and economics of a given cropping preference. Web-based and Geographic Information Systems versions of the model are available for integration with the environmental reporting systems of the irrigation areas.