负载型纳米TiO2光催化剂的制备及其降解水中微量间二甲苯的研究

采用浸涂-烧结法制备的纳米TiO2光催化剂负载量约为6mg／g载体，催化剂经5次重复使用其催化效果稳定，表明催化剂表面TiO2粉体负载牢固；以高压汞灯为光源，对水中微量间二甲苯的负载型纳米TiO2光催化氧化过程的研究表明：初始浓度在6．68～17．36mg／L的范围内，间二甲苯的光催化反应遵循表现一级反应动力学规律，反应的表现速率常数随溶液初始浓度的增大而减小，半衰期则随初始浓度的增大而增加。     

阳离子艳红染料的光催化降解

本文研究了以沉淀法制备的TiO2为催化剂，紫外杀菌灯为光源，对阳离子艳红染料进行光催化降解的可行性，结果表明，在实验条件下，本系统对阳离子艳红染料有明显的降解效果，浓度为10mg/L的阳离子艳红染料经过30min的处理，其降解率＞88％，此外，还探讨了溶液初始pH值，催化剂的投加量，光照距离和液层高度等因素对光降解反应的影响。     

负载型TiO2薄膜光催化剂降解亚甲基蓝

采用溶胶-凝胶法制备了玻璃负载的TiO2薄膜光催化剂，研究了该催化剂对亚甲基蓝溶液的光催化降解，考察了反应时间、水样的初始浓度、溶液的pH等对光催化降解效果的影响。     

UV-H_2O_2联用工艺去除水中阿特拉津的研究

采用间歇式反应器考察了UV-H2O2高级氧化技术去除水中阿特拉津的效果及其影响因素,并进行了相关的反应动力学研究。结果表明,在pH值6.9,阿特拉津初始浓度500μg/L,紫外辐照强度172μW/cm2时,H2O2投加量50mg/L,反应10min后,阿特拉津的去除率90%。UV-H2O2联用工艺对阿特拉津的降解符合一级反应动力学。H2O2在该联用工艺降解阿特拉津中具有双重作用,一方面,当H2O2投加量较小时,一级反应速率常数随H2O2投加量的增加基本呈现线性增加的趋势;另一方面,当H2O2浓度增加到一定程度(90mg/L)后,阿特拉津的降解速率随H2O2浓度的变化已不明显,而H2O2浓度为102mg/L时,则出现了抑制作用。     

TiO2光催化降解有机颜料艳红RGS母液研究

以TiO2为催化剂,对有机颜料艳红RGS母液进行了一系列光催化降解试验.考察了催化剂用量、溶液pH值、初始浓度、不同光源和照射时间对脱色率的影响.结果表明,溶液相对初始浓度为0.2、pH<8、催化剂用量为1g/L时,以紫外灯(254nm)为光源,反应120 min,脱色率可达93%以上.     

HPA／ZnFe2O4-TiO2光催化剂的制备及对马拉硫磷的可见光降解

以纳米TiO2载体，利用浸渍法制备了HPA／ZnFe2O4-TiO2光催化剂。对制备的催化剂进行了XRD、BET、TEM和UV-vis DRS表征。结果表明，催化剂样品均为锐钛矿相且ZnFe2O4很好地分散在载体表面，HPA／ZnFe2O4-TiO2光催化荆的平均粒径为10nm且在380-670nm均有强的光响应；反应最佳的HPA浓度为O.08molfL，最佳的ZnFe2O4负载量为1％。考察了HPA溶液初始浓度、ZnFe2O4负载量、溶液初始pH值、H2O2用量、催化剂用量对催化剂活性的影响。在溶液初始pH=13，H2O2=6mmol／L，催化剂用量为2g/L的最优条件下，光照反应进行100min后，马拉硫磷的降解率可达87％；重复4次后马拉硫磷的降解率仍可以达到67％。     

TiO2/ACF与TiO2/Bi2WO6/ACF材料吸附光催化降解VOCs条件优化及性能评价

通过开展TiO2/ACF与TiO2/BiWO6/ACF材料吸附光催化降解VOCs废气的室内模拟实验,探究反应环境（流量、初始浓度、温度、湿度）对吸附光催化降解效率的影响。结果表明：TiO2/ACF材料的最优降解条件为浓度1000 mg/m3,流量1.2 m3/h,湿度30％,温度33℃;TiO2/BiWO6/ACF材料的最优降解条件 为浓度1000 mg/m3,流量1.2 m3/h,湿度33％,温度34℃;两种材料在最优条件下均具有对高浓度污染物响应速度快、反应平衡后污染物转化率高的特点,TiO2/ACF材料三级反应总体转化率达到81.71％,TiO2/BiWO6/ACF材料三级反应总体转化率达到85.96％。因此,将吸附光催化技术与其他处理技术相结合作为一种预处理方法,针对储罐呼吸气排放源,在实现VOCs初步降解的同时还可以稳定平衡VOCs浓度,具有较好的缓冲、减排效果,该技术工艺流程简单,能耗低,具有很好的应用前景。     

掺杂型二氧化钛纳米管光催化降解甲基橙研究

利用本实验室制备的N-F原子掺杂二氧化钛纳米管作催化剂,在可见光区对甲基橙(MO)进行光催化降解实验。在催化剂用量固定为3cm2时考察了不同初始浓度、pH值、溶解氧(DO)等对降解率的影响。结果表明,在可见光区该催化剂具有较高的光催化活性;当溶液DO为19.2mg/L、pH值为3、初始浓度为10mg/L、反应时间300min时,降解率可达82.3%。     

介孔氧化铁催化降解诺氟沙星实验条件的优化研究

选取诺氟沙星为目标污染物,以介孔氧化铁为催化剂,催化过氧化氢降解水中微量有机污染物,设计正交实验并利用SPSS软件进行数据分析,分别讨论了pH、H_2O_2初始浓度、诺氟沙星初始浓度以及催化剂投加量对降解率的影响,并得到选定因素水平范围内的最优化反应条件:初始p H为7,初始H_2O_2浓度100 m M,初始诺氟沙星浓度2 mg/L,催化剂投加量0.7 g/L。最优化反应条件下,120 min诺氟沙星的降解率达到99%。通过SPPS方差分析可得,各因素影响大小的排序为诺氟沙星初始浓度催化剂投加量初始pH初始H_2O_2浓度。     

La掺杂TiO2/有机改性膨润土对TNT弹药废水的光催化降解性能研究

利用超声强化溶胶-凝胶法制备了La掺杂TiO2/有机改性膨润土复合光催化材料并进行了结构表征;以弹药废水中主要污染物质TNT作为目标物,考察了影响光催化降解性能的因素.结果表明：有机改性后复合材料的吸附性能和光催化性能均有所增加,对TNT的60min的吸附去除率和光催化降解率分别达到9.68％和94.53％;影响TNT光催化降解率的因素有光照时间、催化剂用量、TNT初始浓度、溶液pH值和光照强度.     

Measuring sorption of hydrophilic organic compounds in soils by an unsaturated transient flow method

Determination of sorption of hydrophilic, weakly sorbing organic compounds in soil by conventional batch methods using a slurried suspension is often prone to considerable errors because small changes in the solution concentration on equilibration must be accurately determined. This difficulty is exacerbated for compounds susceptible to degradation, which also decreases the solution concentration. The objective of this study was to determine sorption of hydrophilic pesticides by applying an unsaturated transient flow method, which enables determination of sorption at sufficiently small solution to soil ratios. The method makes use of piston-like displacement of the antecedent solution in equilibrium with sorbed phase when pesticide-free water is infiltrated into a soil column spiked with a pesticide. Pesticide sorption and the solution concentration are inferred from a plot of total pesticide content per unit mass of soil vs. water content in a region where the antecedent solution is accumulated. Thus, extraction of solution from relative dry soil is unnecessary. We tested this method for two hydrophilic pesticides, monocrotophos [dimethyl (E)-1-methyl-2-(methyl-carbamoyl) vinyl phosphate] and dichlorvos (2,2-dichlorovinyl dimethyl phosphate). The sorption coefficient, K(d), obtained for monocrotophos was slightly lower than that by batch method (K(d) = 0.10 vs. 0.19 L kg(-1)), whereas for dichlorvos, a compound highly susceptible to degradation, the unsaturated flow method yielded a much smaller K(d) (0.19 vs. 3.22 L kg(-1)). The K(d) values for both compounds were consistent with the observed retardation in the pesticide displacement in the columns. The proposed method is more representative of field conditions and particularly suitable for weakly sorbing organic compounds in soils.     

纸载P-TiO_2光催化降解甲醛的影响因素研究

本文以牛皮纸作载体,用浸渍法制备了具有光催化作用的纳米P-TiO2光催化剂,对室内一定浓度的甲醛气体进行了降解实验研究。通过实验探讨了甲醛的初始浓度、催化剂的用量、湿度条件、溶胶pH值和金属离子的掺杂5个影响甲醛降解率的因素,结果采用美国interscan公司生产的4160型甲醛分析仪进行表征。实验结果表明,当甲醛的初始浓度约为1.53mg/m3,P-TiO2用量为11.94g,湿度约为52%,溶胶pH=5.01,掺杂6.00mL 0.20 mol/L Cu2＋离子时,甲醛的降解效果最好,最高可达93.50%,甲醛浓度降至0.0994mg/m3,达到了GB/T 18883—2002标准中规定的0.10 mg/m3。     

树脂纳米零价铁催化过硫酸钠降解甲基橙的研究

采用树脂负载零价纳米铁（NZVI-resin）作为铁源,活化过硫酸钠,产生硫酸根自由基氧化降解偶氮染料甲基橙。考察了温度、NZVI-resin加入量、pH值及过硫酸钠的浓度等因素对甲基橙降解率的影响,并对其降解动力学规律作了初步探讨。结果表明：降解反应遵循准一级反应动力学,在pH=3.0、Fe0=0.2 g.L-1、Na2S2O8=1.33 g.L-1的条件下,30 mg.L-1的甲基橙溶液降解率为99.7%。     

超声-生化法降解8-羟基喹啉废水的实验研究

本文采用超声-生化(两级好氧)联用的方法,对8-羟基喹啉废水的降解工艺进行了研究。对废水的预处理方法为超声降解法,文中分析了溶液初始浓度、超声时间、超声全程时间以及超声细胞粉碎机的变幅杆直径大小对废水预处理效果的影响。实验结果表明,变幅杆直径为25mm,溶液初始浓度为0.6g/L,超声全程时间在20min,最佳超声时间为2s时降解效率最高,CODcr去除率可以达到40.4%。本实验生化处理方法为普通活性污泥法(两级好氧),一级好氧反应池停留时间选择10h,去除率为69.4%;二级好氧反应池停留时间选择6h,去除率为71.7%。超声-生化(两级好氧)联用对8-羟基喹啉废水处理效果良好,CODcr总去除率达到94.4%。     

Formaldehyde degradation in the presence of methanol by photo-Fenton process

In this study, the photo-Fenton process for the degradation of formaldehyde was investigated in lab-scale experiments. Results showed that methanol, the additive chemical in a commercial product of formaldehyde, was also decomposed during the formaldehyde oxidation reaction. The oxidation reaction was in three-stages. The first stage was the Fe(2+)/H(2)O(2) reaction in which both formaldehyde and methanol were swiftly decomposed. The second and the third stages exerted a somewhat less rapid degradation of both chemicals. The first stage of the oxidation reaction can be discussed by means of the initial average rate and the third stage or Fe(3+)/H(2)O(2) stage was found to follow the first order reaction rate. The reaction was influenced by the initial pH, the concentration of hydrogen peroxide, the amount of ferrous ions. The initial pH at 2.6 provided the highest removal efficiencies in this system. In addition, the competition between formaldehyde and methanol was investigated and described as r(m)/r(f), where r(m) and r(f) were the initial rates of methanol and formaldehyde, respectively. The addition of methanol exhibited a competitive effect on formaldehyde degradation. The removal of formaldehyde decreased with increasing methanol concentration. At the high concentrations of methanol, the oxidation reaction of formaldehyde was repressed. It appears that all values of r(m)/r(f) obtained from the experiments are lower than the theoretical values.     

Degradation of soil fumigants as affected by initial concentration and temperature

Soil fumigation using shank injection creates high fumigant concentration gradients in soil from the injection point to the soil surface. A temperature gradient also exists along the soil profile. We studied the degradation of methyl isothiocyanate (MITC) and 1,3-dichloropropene (1,3-D) in an Arlington sandy loam (coarse-loamy, mixed, thermic Haplic Durixeralf) at four temperatures and four initial concentrations. We then tested the applicability of first-order, half-order, and second-order kinetics, and the Michaelis-Menten model for describing fumigant degradation as affected by temperature and initial concentration. Overall, none of the models adequately described the degradation of MITC and 1,3-D isomers over the range of the initial concentrations. First-order and half-order kinetics adequately described the degradation of MITC and 1,3-D isomers at each initial concentration, with the correlation coefficients greater than 0.78 (r2> 0.78). However, the derived rate constant was dependent on the initial concentration. The first-order rate constants varied between 6 and 10x for MITC for the concentration range of 3 to 140 mg kg(-1), and between 1.5 and 4x for 1,3-D isomers for the concentration range of 0.6 to 60 mg kg(-1), depending on temperature. For the same initial concentration range, the variation in the half-order rate constants was between 1.4 and 1.7x for MITC and between 3.1 and 6.1x for 1,3-D isomers, depending on temperature. Second-order kinetics and the Michaelis-Menten model did not satisfactorily describe the degradation at all initial concentrations. The degradation of MITC and 1,3-D was primarily biodegradation, which was affected by temperature between 20 and 40 degrees C, following the Arrhenius equation (r2 > 0.74).     

Phenol degradation using combined effects of hydrodynamic cavitation and oxidant: Doehlert matrix

Hydrodynamic cavitation (HC)-based treatments have been proposed for the degradation of phenol as a toxic pollutant. The present work aimed to optimize the degradation of phenol using HC by means of Doehlert experimental design, which has not been previously addressed. Initially, operational parameters of hydraulic characteristics of the pump, inlet pressure, solution pH, and initial concentration were optimized; later, the effects of pH solution and H₂O₂ loading or initial pollutant concentration on phenol degradation were explored using the Doehlert experimental design. It was observed that phenol degradation is strongly dependent on the pH of the solution. Also, the acidic condition favors the formation of hydroxyl radicals and thus, the degradation of phenol. Based on the Doehlert matrix, the 94.1% phenol degradation and 68.60% total organic carbon (TOC) were obtained in 180 min at 304.5 mg/L of hydrogen peroxide at an initial concentration of 20 mg/L, 2.0 pH, and 90 psi inlet pressure, providing a cavitational yield of 6.33 × 10⁻⁶ mg/J and minimum treatment cost of US$/L 0.13. Overall, it has been observed that HC can be a promising route for the removal of pollutants (phenol) effectively using hydrogen peroxide as an additive.     

Fenton试剂高级氧化法降解甲基橙模拟废水研究

甲基橙是一种较难降解的有机苯环偶氮染料之一，研究其降解性能对其他染料废水体系的降解研究具有普遍参考价值。通过研究Fenton试剂降解甲基橙过程中的H202浓度、Fe2＋浓度、反应时间和反应体系pH值对甲基橙降解的影响，确定其最佳降解工艺条件为：当甲基橙浓度为20mg／L、pH值为3、Fe2＋浓度为1．5mmol／L、H2O2为32mmol/L时，降解率达到最大值（98．95％）。