Mercury oxidation promoted by a selective catalytic reduction catalyst under simulated Powder River Basin coal combustion conditions

A bench-scale reactor consisting of a natural gas burner and an electrically heated reactor housing a selective catalytic reduction (SCR) catalyst was constructed for studying elemental mercury (Hg(o)) oxidation under SCR conditions. A low sulfur Powder River Basin (PRB) subbituminous coal combustion fly ash was injected into the entrained-flow reactor along with sulfur dioxide (SO2), nitrogen oxides (NOx), hydrogen chloride (HCl), and trace Hg(o). Concentrations of Hg(o) and total mercury (Hg) upstream and downstream of the SCR catalyst were measured using a Hg monitor. The effects of HCl concentration, SCR operating temperature, catalyst space velocity, and feed rate of PRB fly ash on Hg(o) oxidation were evaluated. It was observed that HCl provides the source of chlorine for Hg(o) oxidation under simulated PRB coal-fired SCR conditions. The decrease in Hg mass balance closure across the catalyst with decreasing HCl concentration suggests that transient Hg capture on the SCR catalyst occurred during the short test exposure periods and that the outlet speciation observed may not be representative of steady-state operation at longer exposure times. Increasing the space velocity and operating temperature of the SCR led to less Hg(o) oxidized. Introduction of PRB coal fly ash resulted in slightly decreased outlet oxidized mercury (Hg2+) as a percentage of total inlet Hg and correspondingly resulted in an incremental increase in Hg capture. The injection of ammonia (NH3) for NOx reduction by SCR was found to have a strong effect to decrease Hg oxidation. The observations suggest that Hg(o) oxidation may occur near the exit region of commercial SCR reactors. Passage of flue gas through SCR systems without NH3 injection, such as during the low-ozone season, may also impact Hg speciation and capture in the flue gas.     

Pilot-scale study of the effect of selective catalytic reduction catalyst on mercury speciation in Illinois and Powder River Basin coal combustion flue gases

A study was conducted to investigate the effect of selective catalytic reduction (SCR) catalyst on mercury (Hg) speciation in bituminous and subbituminous coal combustion flue gases. Three different Illinois Basin bituminous coals (from high to low sulfur [S] and chlorine [Cl]) and one Powder River Basin (PRB) subbituminous coal with very low S and very low Cl were tested in a pilot-scale combustor equipped with an SCR reactor for controlling nitrogen oxides (NOx) emissions. The SCR catalyst induced high oxidation of elemental Hg (Hg0), decreasing the percentage of Hg0 at the outlet of the SCR to values <12% for the three Illinois coal tests. The PRB coal test indicated a low oxidation of Hg0 by the SCR catalyst, with the percentage of Hg0 decreasing from approximately 96% at the inlet of the reactor to approximately 80% at the outlet. The low Cl content of the PRB coal and corresponding low level of available flue gas Cl species were believed to be responsible for low SCR Hg oxidation for this coal type. The test results indicated a strong effect of coal type on the extent of Hg oxidation.     

Release of Mercury Vapor from Coal Combustion Ash

Abstract

The long-term stability of Hg in coal combustion byproducts (CCBs) was evaluated at ambient and near-ambient temperatures. Six CCB samples with atypically high levels of total Hg were selected for study assuming a greater potential for release of measurable amounts of Hg vapor. The samples selected included two fly ash samples from U.S. eastern bituminous coal, two fly ash samples from South African low-rank coal, one fly ash from Powder River Basin (PRB) subbituminous coal blended with petroleum coke, and one PRB subbituminous coal fly ash incorporated with flue gas desulfurization material.

Air scrubbed of Hg was passed through compacted 100-g aliquots of each sample at 1 mL/min and vented to a gold-coated quartz trap to collect released Hg vapor. The samples were maintained at ambient and near-ambient (37 °C) temperatures. All samples released low-picogram levels of Hg after 90 days. No pattern was evident to link the total Hg content to the rate of release of Hg vapor. An average of 0.030 pg Hg/g CCB/day was released from the samples, which equates to 2.2 x 10^-8 lb Hg/ton CCB/year. If this were applied to a coal-fired power plant production of 200,000 tons of fly ash per year, there would be a maximum potential release of 0.0044 lb, or 2.00 g, of Hg per year. Experiments are continuing to determine long-term vapor release of Hg from CCBs. All samples have been set up in duplicate at ambient temperature with an improved apparatus to reevalu-ate results reported in this article.     

Pilot-Scale Study of the Effect of Selective Catalytic Reduction Catalyst on Mercury Speciation in Illinois and Powder River Basin Coal Combustion Flue Gases

Abstract

A study was conducted to investigate the effect of selective catalytic reduction (SCR) catalyst on mercury (Hg) speciation in bituminous and subbituminous coal combustion flue gases. Three different Illinois Basin bituminous coals (from high to low sulfur [S] and chlorine [Cl]) and one Powder River Basin (PRB) subbituminous coal with very low S and very low Cl were tested in a pilot-scale combustor equipped with an SCR reactor for controlling nitrogen oxides (NO_x) emissions. The SCR catalyst induced high oxidation of elemental Hg (Hg⁰), decreasing the percentage of Hg⁰ at the outlet of the SCR to values <12% for the three Illinois coal tests. The PRB coal test indicated a low oxidation of Hg⁰ by the SCR catalyst, with the percentage of Hg⁰ decreasing from ～96% at the inlet of the reactor to ～80% at the outlet. The low Cl content of the PRB coal and corresponding low level of available flue gas Cl species were believed to be responsible for low SCR Hg oxidation for this coal type. The test results indicated a strong effect of coal type on the extent of Hg oxidation.     

Spatial distribution and partitioning of polychlorinated biphenyl and organochlorine pesticide in water and sediment from Sarno River and Estuary,Southern Italy

The Sarno River is nicknamed “the most polluted river in Europe”. The main goal of this study is to enhance our knowledge on the Sarno River water and sediment quality and on its environmental impact on the gulf of Naples (Tyrrhenian Sea, Central Mediterranean Sea) in order to become a useful assessment tool for the regional administrations. For these reasons, 32 selected polychlorinated biphenyls (PCBs) and aldrin, α-BHC, β-BHC, δ-BHC, γ-BHC (lindane), 4,4′-DDD, 4,4′-DDE, 4,4′-DDT, dieldrin, endosulfan I, endosulfan II, endosulfan sulphate, endrin, endrin aldehyde, heptachlor, heptachlor epoxide (isomer B) and methoxychlor were determined in the water dissolved phase (DP), suspended particulate matter (SPM) and sediments. Total concentrations of PCBs ranged from 1.4 to 24.9 ng L^?1 in water (sum of DP and SPM) and from 1.01 to 42.54 ng g^?1 in sediment samples. The concentrations of total organochlorine pesticides (OCPs) obtained in water (sum of DP and SPM) ranged from 0.54 to 7.32 ng L^?1 and from 0.08 to 5.99 ng g^?1 in sediment samples. Contaminant discharges of PCBs and OCPs into the sea were calculated in about 1,247 g day^?1 (948 g day^?1 of PCBs and 326 g day^?1 of OCPs), showing that this river should account as one of the main contribution sources of PCBs and OCPs to the Tyrrhenian Sea.     

Mercury and methyl mercury in higher fungi and their relation with the substrata in a cinnabar mining area

195 specimens of higher fungi and their substrata collected in the Hg mining area of M.Amiata and around Siena (Central Italy), were analyzed for their total Hg content. Whereas wood decomposers and many species of mycorrhizal fungi accumulated the metal at a very low rate, some mycorrhizal species and all the humus decomposers may accumulate up to 100 μg.g^?1d.w. of Hg and in the least contaminated sites, up to 63 times as much Hg as the substratum. Instead in mineralized areas the concentration factor rarely exceeded 1. The methyl mercury content of 35 species (almost all edible), ranged between 0.01 and 3.7 μg.g^?1 d.w..The possible significance of these findings and the toxicologic implications for local co$\text{n}$ sumers are considered.     

Determination of PM2.5 sources using time-resolved integrated source and receptor models

Multivariate statistical techniques are applied to particulate matter (PM) and meteorological data to identify the sources responsible for evening PM spikes at Sunland Park, NM (USA). The statistical techniques applied are principal components analysis (PCA), redundancy analysis (RDA), and absolute principal components scores analysis (APCSA), and the data evaluated are 3-h average (6–9 p.m.) PM_2.5 mass and chemical composition and 1-h average PM_2.5 and PM₁₀ mass and environmental data collected in the winter of 2002. Although the interpretation of the data was complicated by the presence of sources which are likely changing in time (e.g. brick kilns), the multivariate analyses indicate that the evening high PM_2.5 is associated with burning-activities occurring to the south of Sunland Park, and these emissions are characterized by elevated Sb, Cl⁻, and elemental carbon; ∼68% of the PM_2.5 mass can be attributed to this source. The PM₁₀ evening peaks, on the other hand, are mainly caused by resuspended dust generated by vehicular movements south of the site and transported by the local terrain-induced drainage flow.     

Atmospheric trace element deposition: principal component analysis of ICP-MS data from moss samples

Data from a Norwegian survey on atmospheric deposition, including 33 elements in 495 moss samples collected in 1990, are presented. The biomonitor moss used was Hylocomium splendens, and the analyses were carried out by ICP-MS. Principal component analysis is used to identify possible sources of the elements determined in the mosses. Dominant factors represent long-range atmospheric transported elements (Bi, Pb, Sb, Mo, Cd, V, As, Zn, Tl, Hg, Ga), windblown mineral particles (Y, La, Al, Li, U, Th, Ga, Fe, V, Cr), local emission sources (Ni, Cu, Co, and As; Zn, Cd, and Hg; Fe, Cr, and Al), transport from the marine environment (Mg, B, Na, Sr, Ca), and contribution from higher plants (Cs, Rb, Ba, Mn). Comparison of the results with similar surveys from 1977 and 1985 show a decreasing contribution of most long-range transported elements to southern Norway.     

A laboratory-incubated redox oscillation experiment to investigate Hg fluxes from highly contaminated coastal marine sediments (Gulf of Trieste,Northern Adriatic Sea)

Mercury (Hg) mobility at the sediment–water interface was investigated during a laboratory incubation experiment conducted with highly contaminated sediments (13 μg g^-1) of the Gulf of Trieste. Undisturbed sediment was collected in front of the Isonzo River mouth, which inflows Hg-rich suspended material originating from the Idrija (NW Slovenia) mining district. Since hypoxic and anoxic conditions at the bottom are frequently observed and can influence the Hg biogeochemical behavior, a redox oscillation was simulated in the laboratory, at in situ temperature, using a dark flux chamber. Temporal variations of several parameters were monitored simultaneously: dissolved Hg (DHg) and methylmercury (MeHg), O₂, NH₄ ⁺, NO₃ ^- + NO₂ ^-, PO₄ ^3-, H₂S, dissolved Mn²⁺, dissolved inorganic and organic carbon (DIC and DOC). Under anoxic conditions, both Hg (665 ng m² day^-1) and MeHg (550 ng m² day^-1) fluxed from sediments into the water column, whereas re-oxygenation caused concentrations of MeHg and Hg to rapidly drop, probably due to re-adsorption onto Fe/Mn-oxyhydroxides and enhanced demethylation processes. Hence, during anoxic events, sediments of the Gulf of Trieste may be considered as an important source of DHg species for the water column. On the contrary, re-oxygenation of the bottom compartment mitigates Hg and MeHg release from the sediment, thus acting as a natural “defence” from possible interaction between the metal and the aquatic organisms.     

Temporal variability of mercury speciation in urban air

Semi-continuous measurements of ambient mercury (Hg) species were performed in Detroit, MI, USA for the calendar year 2003. The mean (±standard deviation) concentrations for gaseous elemental mercury (GEM), particulate mercury (HgP), and reactive gaseous mercury (RGM) were 2.2±1.3 ng m⁻³, 20.8±30.0, and 17.7±28.9 pg m⁻³, respectively. A clear seasonality in Hg speciation was observed with GEM and RGM concentrations significantly (p<0.001) greater in warm seasons, while HgP concentrations were greater in cold seasons. The three measured Hg species also exhibited clear diurnal trends which were particularly evident during the summer months. Higher RGM concentrations were observed during the day than at night. Hourly HgP and GEM concentrations exhibited a similar diurnal pattern with both being inversely correlated with RGM. Multivariate analysis coupled with conditional probability function analysis revealed the conditions associated with high Hg concentration episodes, and identified the inter-correlations between speciated Hg concentrations, three common urban air pollutants (sulfur dioxide, ozone, and nitric oxides), and meteorological parameters. This analysis suggests that both local and regional sources were major factors contributing to the observed temporal variations in Hg speciation. Boundary layer dynamics and the seasonal meteorological conditions, including temperature and moisture content, were also important factors affecting Hg variability.     

Atmospheric emissions of F,As, Se,Hg, and Sb from coal-fired power and heat generation in China

Coal is one of the major energy resources in China, with nearly half of produced Chinese coal used for power and heat generation. The large use of coal for power and heat generation in China may result in significant atmospheric emissions of toxic volatile trace elements (i.e. F, As, Se, Hg, and Sb). For the purpose of estimating the atmospheric emissions from coal-fired power and heat generation in China, a simple method based on coal consumption, concentration and emission factor of trace element was adopted to calculate the gaseous emissions of elements F, As, Se, Hg, and Sb. Results indicate that about 162 161, 236, 637, 172, and 33 t F, As, Se, Hg, and Sb, respectively, were introduced into atmosphere from coal combustion by power and heat generation in China in 2009. The atmospheric emissions of F, As, Se, Hg, and Sb by power and heat generation increased from 2005 to 2009 with increasing coal consumptions.     

Release of mercury vapor from coal combustion ash

The long-term stability of Hg in coal combustion by-products (CCBs) was evaluated at ambient and near-ambient temperatures. Six CCB samples with atypically high levels of total Hg were selected for study assuming a greater potential for release of measurable amounts of Hg vapor. The samples selected included two fly ash samples from U.S. eastern bituminous coal, two fly ash samples from South African low-rank coal, one fly ash from Powder River Basin (PRB) subbituminous coal blended with petroleum coke, and one PRB subbituminous coal fly ash incorporated with flue gas desulfurization material. Air scrubbed of Hg was passed through compacted 100-g aliquots of each sample at 1 mL/min and vented to a gold-coated quartz trap to collect released Hg vapor. The samples were maintained at ambient and near-ambient (37 degrees C) temperatures. All samples released low-picogram levels of Hg after 90 days. No pattern was evident to link the total Hg content to the rate of release of Hg vapor. An average of 0.030 pg Hg/g CCB/day was released from the samples, which equates to 2.2 x 10(-8) lb Hg/ton CCB/year. If this were applied to a coal-fired power plant production of 200,000 tons of fly ash per year, there would be a maximum potential release of 0.0044 lb, or 2.00 g, of Hg per year. Experiments are continuing to determine long-term vapor release of Hg from CCBs. All samples have been set up in duplicate at ambient temperature with an improved apparatus to reevaluate results reported in this article.     

Chemical content and source apportionment of 36 heavy metal analysis and health risk assessment in aerosol of Beijing

The concentration levels of 36 airborne heavy metals and atmospheric radioactivity in total suspended particulate (TSP) samples were measured to investigate the chemical characteristics, potential sources of aerosols, and health risk in Beijing, China, from September 2016 to September 2017. The TSP concentrations varied from 6.93 to 469.18 μg/m³, with a median of 133.97 μg/m³. The order for the mean concentrations of heavy metals, known as hazardous air pollutants (HAPs), was as follows: Mn > Pb > As > Cr > Ni > Se > Cd > Co > Sb > Hg > Be; Non-Designated HAPs Metals: Ca > Fe > Mg > Al > K > Na > Zn > P > Ba > Ti > Cu > Sr > B > Sn > I > V > Rb > Ce > Mo > Cs > Th > Ag > U > Pt. The median concentration of As was higher than China air quality standard (6 ng/m³). The gross α and β concentration levels in aerosols were (1.84?±?1.59) mBg/m³ and (1.15?±?0.85) mBg/m³, respectively. The enrichment factor values of Cu, Ba, B, Ce, Tl, Cs, Pb, As, Cd, Sb, Hg, Fe, Zn, Sn, I, Mo, and Ag were higher than 10, which indicated enriched results from anthropogenic sources. Pb, As, and Cd are considered to originate from multiple sources; fireworks released Ba during China spring festival; Fe, Ce, and Cs may come from stable emissions such as industrial gases. The health risks from anthropogenic metals via inhalation, ingestion, and dermal pathway were estimated on the basis of health quotient as well as the results indicated that children faced the higher risk than adults during the research period. For adults, the health risk posed by heavy metals in atmospheric particles was below the acceptable level.

     

Characterization of Activated Carbon Fiber Filters for Pressure Drop,Submicrometer Particulate Collection,and Mercury Capture

ABSTRACT

The use of activated carbon fiber (ACF) filters for the capture of particulate matter and elemental Hg is demonstrated. The pressure drop and particle collection efficiency characteristics of the ACF filters were established at two different face velocities and for two different aerosols: spherical NaCl and combustion-generated silica particles. The clean ACF filter specific resistance was 153 kg m^-2 sec^-1. The experimental specific resistance for cake filtration was 1.6 × 10⁶ sec^-1 and 2.4 × 10⁵ sec^-1 for 0.5- and 1.5-μm mass median diameter particles, respectively. The resistance factor R was approximately 2, similar to that for the high-efficiency particulate air filters. There was a discrepancy in the measured particle collection efficiencies and those predicted by theory. The use of the ACF filter for elemental Hg capture was illustrated, and the breakthrough characteristic was established. The capacity of the ACF filter for Hg capture was similar to other powdered activated carbons.     

Atmospheric trace element concentrations in total suspended particles near Paris,France

To evaluate today’s trace element atmospheric concentrations in large urban areas, an atmospheric survey was carried out for 18 months, from March 2002 to September 2003, in Saclay, nearby Paris. The total suspended particulate matter (TSP) was collected continuously on quartz fibre filters. The TSP contents were determined for 36 elements (including Ag, Bi, Mo and Sb) using two analytical methods: Instrumental Neutron Activation Analysis (INAA) and Inductively Coupled Plasma Mass Spectrometry (ICP-MS). The measured concentrations were in agreement within the uncertainties with the certified values for the polycarbonate reference material filter SRM-2783 (National Institute for Standard Technology NIST, USA). The measured concentrations were significantly lower than the recommended atmospheric concentrations. In 2003, the Pb atmospheric level at Saclay was 15 ng/m³, compared to the 500 ng/m³ guideline level and to the 200 ng/m³ observed value in 1994. The typical urban background TSP values of 1–2, 0.2–1, 4–6, 10–30 and 3–5 ng/m³ for As, Co, Cr, Cu and Sb, respectively, were inferred from this study and were compared with the literature data. The typical urban background TSP concentrations could not be realised for Cd, Pb and Zn, since these air concentrations are highly influenced by local features. The Zn concentrations and Zn/Pb ratio observed in Saclay represented a characteristic fingerprint of the exceptionally large extent of zinc-made roofs in Paris and its suburbs. The traffic-related origin of Ba, Cr, Cu, Pb and Sb was demonstrated, while the atmospheric source(s) of Ag was not identified.     

Persistent organic pollutants in the atmosphere from urban and industrial environments in the Rhine Valley: PCBs, PCDD/Fs

Polychlorinated biphenyls (PCBs) and polychlorinated dibenzodioxin and furan (PCDD/F) concentrations in the atmosphere were analysed using passive air samplers (PAS) close to the Rhine River between France and Germany. Collectors were placed in industrial, urban, rural and remote areas (Vosges Mountains) between March 2009 and August 2010, and the mean PCB concentrations (sum of 22 congeners) were 3.3, 3.9, 4.1 and 1.4 ng?PAS^?1?day^?1, respectively. Two events during the sampling period were observed in April 2009 and February–March 2010 with the highest PCB concentrations found in the industrial area (19.6 ng?PAS^?1?day^?1). PCDD/F level were measured during these periods, and the maximum concentration observed was from 37.5 fg?WHO?PAS^?1?day^?1     

Remanence of lead pollution in an urban river system: a multi-scale temporal and spatial study in the Seine River basin,France

Total lead (Pb) concentration and Pb isotopic ratio (²⁰⁶Pb/²⁰7Pb) were determined in 140 samples from the Seine River basin (France), covering a period of time from 1945 to 2011 and including bed sediments (bulk and size fractionated samples), suspended particulate matter (SPM), sediment cores, and combined sewer overflow (CSO) particulate matter to constrain the spatial and temporal variability of the lead sources at the scale of the contaminated Seine River basin. A focus on the Orge River subcatchment, which exhibits a contrasted land-use pattern, allows documenting the relation between hydrodynamics, urbanization, and contamination sources. The study reveals that the Pb contamination due to leaded gasoline that peaked in the 1980s has a very limited impact in the river nowadays. In the upstream Seine River, the isotopic ratio analysis suggests a pervasive contamination which origin (coal combustion and/or gasoline lead) should be clarified. The current SPM contamination trend follows the urbanization/industrialization spatial trend. Downstream of Paris, the lead from historical use originating from the Rio Tinto mine, Spain (²⁰⁶Pb/²⁰⁷Pb?=?1.1634?±?0.0001) is the major Pb source. The analysis of the bed sediments (bulk and grain size fractionated) highlights the diversity of the anthropogenic lead sources in relation with the diversity of the human activities that occurred in this basin over the years. The “urban” source, defined by waste waters including the CSO samples (²⁰⁶Pb/²⁰⁷Pb?=?1.157?±?0.003), results of a thorough mixing of leaded gasoline with “historical” lead over the years. Finally, a contamination mixing scheme related to hydrodynamics is proposed.     

Distribution and accumulation of elements (As, Cu, Fe, Hg, Mn, and Zn) in tissues of fish species from different trophic levels in the Danube River at the confluence with the Sava River (Serbia)

Pikeperch (Sander lucioperca), European catfish (Silurus glanis), common carp (Cyprinus carpio), and gobies (Neogobius gymnotrachelus, Neogobius melanostomus) were collected from the Danube River (Belgrade section), and samples of liver, muscle, or whole-body composites (in the case of gobies) were analyzed for As, Cu, Fe, Hg, Mn, and Zn with inductively coupled plasma optical spectrometry to find out if there was a correlation between accumulation of these elements in predatory and prey species, as well as in pairs of species with overlapping diets. Concentrations of all analyzed elements were either higher (Cu, Fe, Mn, Zn) in liver than in muscle, or equal (As, Hg), except for Hg in carp, which was higher in muscle. Mercury concentration in liver and muscle of predators (catfish, pikeperch) was significantly (<10^?4) higher than in prey fishes (carp and gobies). The results indicate that Hg concentration was biomagnified through the food chain. Concentrations of As, Fe, and Hg in carp liver and gobies whole-body composite were similar, but carp had significantly (<10^?4) higher values of Zn and Cu in liver. The regression analysis and trendline equations indicate that the concentrations of all tested elements, except for As in liver, and Mn and Fe in muscle, were similar in predatory fish (pikeperch and catfish), on one hand, and in prey fish (carp and gobies), on the other hand. Distinctly high Zn concentration in carp is very common in this species due to its physiology. Concentrations of Hg and Zn were higher than the maximum acceptable concentration due to the high pollution level in this section of the Danube River, accordingly posing a risk for the human consumption of these fish species.     

Variations in source apportionments of nutrient load among seasons and hydrological years in a semi-arid watershed: GWLF model results

Quantifying source apportionments of nutrient load and their variations among seasons and hydrological years can provide useful information for watershed nutrient load reduction programs. There are large seasonal and inter-annual variations in nutrient loads and their sources in semi-arid watersheds that have a monsoon climate. The Generalized Watershed Loading Function model was used to simulate monthly nutrient loads from 2004 to 2011 in the Liu River watershed, Northern China. Model results were used to investigate nutrient load contributions from different sources, temporal variations of source apportionments and the differences in the behavior of total nitrogen (TN) and total phosphorus (TP). Examination of source apportionments for different seasons showed that point sources were the main source of TN and TP in the non-flood season, whereas contributions from diffuse sources, such as rural runoff, soil erosion, and urban areas, were much higher in the flood season. Furthermore, results for three typical hydrological years showed that the contribution ratios of nutrient loads from point sources increased as streamflow decreased, while contribution ratios from rural runoff and urban area increased as streamflow increased. Further, there were significant differences between TN and TP sources on different time scales. Our findings suggest that priority actions and management measures should be changed for different time periods and hydrological conditions, and that different strategies should be used to reduce loads of nitrogen and phosphorus effectively.     

Spatial and temporal trends of metals and arsenic in German freshwater compartments

Cadmium, lead, mercury, copper, nickel, zinc, and arsenic were analyzed in suspended particulate matter (SPM), zebra mussels, and bream sampled yearly under the program of the German Environmental Specimen Bank (ESB) in the rivers Rhine, Elbe, Danube, Saar, Mulde, and Saale and in Lake Belau. Temporal and spatial trends were analyzed, correlations between metal levels in different specimen types assessed, and sampling sites ranked according to their metal levels by calculating a Multi-Metal Index (MMI) for every specimen type and site. SPM: Highest metal loads were detected in Mulde, Saale, and Elbe right downstream of the Saale confluence. In the Elbe, metal loads in SPM were mostly highest in the upper and middle section of the river while in Rhine and Saar concentrations increased downstream. Temporal trends since 2005 were detected only at three sites. Zebra mussel: MMIs were highest in the tidal section of the Elbe and the lower Rhine and lowest in Lake Belau and the upper Danube. Different temporal trends were detected since the early 1990s depending on site and metal. Bream: As, Pb, Cu, and Hg were analyzed in muscle tissue and Pb, Cd, Cu, and Zn in liver. For both tissues, MMIs were highest in Mulde and Saale and the lower and middle Elbe. Since the early 1990s, Hg, Pb, and Cu decreased in bream muscle at many sites while As increased at 6 of the 17 sites. The findings indicate that Hg, Pb, and Cu have obviously decreased in many freshwater ecosystems in recent years, whereas As and Ni levels have increased at several sites. Metal levels and temporal trends mostly differed between the specimen types under investigation and only few correlations between specimen types were detected. This underlines the importance of including different components of an ecosystem when assessing its environmental quality.