Leaching characteristics of residual lateritic soils stabilised with fly ash and lime for geotechnical applications

The effective use of residual lateritic soils as fill material for various construction activities is often limited by the difficulty in handling them. Attempt to improve their workability with fly ash and lime has shown promising results, although accompanied by risk of release of heavy metal leachates to the groundwater. In the present work, the leaching properties from residual lateritic soils from a part of Northeast India stabilised with fly ash and lime (CaO) was investigated with the help of single batch leaching test and column leaching test for different soil-fly ash-lime mixes. Test results show that the high pH induced by lime treatment of the mixes helps in keeping most of the metals within the stabilised soil matrix. Although the heavy metal concentrations in the leachates were generally within permissible limits, the release response for different metals was different suggesting implications for permeate solutions having metal pre-concentrations, such as those emanating from hazardous landfill sites. The observed characteristics provide insights towards the potential and realistic estimates of leaching of metals and its variation due to change in fly ash and lime content in the stabilised mix. Many of these constituents found in the stabilised soil had a first-flush phenomenon. But, as they occur only for short duration (about 5 pore volumes over 5 days) and at low concentration, dilution effect may eliminate them. The effect of continuous permeation on the flow parameters and the leaching pattern of the mixes have also been highlighted.     

The performance of a natural treatment system for landfill leachate with special emphasis on the fate of organic pollutants.

A natural treatment system for the treatment of leachate was studied at Moskogen landfill in southern Sweden. This facility consists of three consecutive ponds and a soil-plant (SP)-system. A test area, receiving water from the third pond with the same hydraulic load as the SP-system, was used for estimation of the latter system. Quality parameters including biochemical oxygen demand, total organic carbon, ammonium, nitrate, orthophosphate, and total suspended solids along the treatment line were determined as well as soluble metals (Cu, Cd, Zn, Cr, Ni, and Pb). In addition a thorough investigation along the treatment line has also been performed concerning volatile organic compounds and semi-volatile organic compounds. Non-polar organic compounds were investigated using gas chromatography-mass spectrometry. Quantification was based on the assumption of equal response for the compounds found in comparison with the chosen marker substances. For polar, water-soluble compounds the measurements were restricted to phenolic compounds using high-performance liquid chromatography. Several different types of organic compounds were found in the raw leachate including aromatics, benzene-sulfonamides, biphenyls, naphthalene, organic phosphates, polycyclic aromatic hydrocarbons, polychlorinated biphenyls, phenols and phthalates. The treatment system efficiently reduced organic pollutants, heavy metals, and nitrogen/phosphorous compounds. Most metals and organic compounds in the leachate were already significantly reduced to a low level in the treatment ponds and ammonium-N was efficiently transformed to nitrate-N in the SP-system.     

The Handling And Disposal Of Residuals From The Treatment Of Urban Stormwater Runoff From Separate Storm Drainage Systems

Given the magnitude of stormwater runoff (from separate storm drainage systems) and its pollutional contribution, the treatment of stormwater would generate residuals in amounts equal to or in excess of the volume of sludge now generated by municipal wastewater treatment. The characteristics of stormwater runoff differ substantially from that of wastewater or combined sewer overflow (CSO) in several important parameters, most notably suspended solids (SS) and organic content. The increased SS content of stormwater runoff results in higher volumes of residuals and increased handling and disposal costs. Similarly, the lower organic and nutrient content of stormwater runoff limits both the effectiveness of conventional biological treatment processes and land application disposal options. Several treatment and handling approaches are discussed and evaluated, including both centralized and satellite options. In addition, the primary and secondary economic (e.g. cost, land requirements) and environmental (e.g. air and water pollution, public health, etc.) impacts of stormwater runoff residuals treatment, handling, and disposal are reviewed.     

Literature review: Electrodialytic remediation and potential environmental applications of oil fly ash

Oil fly ash (OFA) contains environmentally toxic heavy metal and substituted polycyclic aromatic hydrocarbons. This review discusses the physical and chemical properties of OFA and presents information from other types of fly ash that can be used as concepts for the remediation and uses of OFA. Electrokinetic remediation is useful to remove some of the heavy metals for broader uses of the fly ash in agriculture, for making construction material, for contaminated wastewater treatment, and also for carbon dioxide sequestration. This review can be useful to develop approaches for the remediation and environmental management of OFA. © 2012 Wiley Periodicals, Inc.     

Chemical characterization of landfill leachates--400 parameters and compounds

A large number of hazardous compounds can be expected to be present in landfill leachates, many of which have not yet been identified. Thus this study screened samples from 12 Swedish municipal landfill sites for 400 parameters and compounds. More than 90 organic and metal organic compounds and 50 inorganic elements were detected, some of which seem to have not been detected before. Compounds detected include halogenated aliphatic compounds, benzene and alkylated benzenes, phenol and alkylated phenols, ethoxylates, polycyclic aromatic compounds, phthalic esters, chlorinated benzenes, chlorinated phenols, PCB, chlorinated dioxins and chlorinated furans, bromated flame-retardants, pesticides, organic tin, methyl mercury and heavy metals. The presence of this large number of hazardous compounds in landfill leachates should have a significant impact on future landfill risk assessments and the development of leachate treatment methods. We propose that future research should pay more attention to the metal-organic and organic compounds detected in this study. We also suggest using leachate sediments as a matrix for detecting hydrophobic compounds, and reflecting on the degradation phase when evaluating results from monitoring studies. The extensive compilation of compounds in this paper can be used to select compounds to search for in future studies.     

Comparison of leaching characteristics of heavy metals in APC residue from an MSW incinerator using various extraction methods

This study investigates four extraction methods (water extraction, toxicity characteristics leaching procedure (TCLP), modified TCLP with pH control, and sequential chemical extraction (SCE)), each representing different liquid-to-solid (L/S) ratios, pH controls, and types of leachant, and their effects on the leaching concentration of heavy metals in municipal solid waste (MSW) incinerator air pollution control (APC) residue. The results indicated that for extraction with distilled water, the heavy metal leaching concentration (mg/l) decreased with L/S ratio, but the amount of heavy metal released (AHMR), defined as the leached amount of heavy metals to the weight of the tested sample (mg/kg), increased with an increase in L/S ratio, in the range of 2-100. The results also showed that both the leaching concentration and the amount of released metals were strongly pH-dependent in the TCLP and modified TCLP tests. In the case of pHs lower than 6.5, the leaching concentrations of Cd, Pb, Cu, Zn, and Cr decreased with an increase in pH. As pH increased higher than 6.5, Cr and Zn were almost insoluble. Meanwhile, Cd and Cu also showed a similar trend but at pHs of 8.5 and 7.5, respectively. Due to the nature of amphoteric elements, in the case of pHs higher than 7, the Pb leaching concentration increased with increasing pH. In modified TCLP tests with the pH value controlled at the same level as in the SCE test, the heavy metal speciation approached the extractable carbonate bound fraction by the SCE. Both amounts of targeted metals leached from the SCE and modified TCLP tests were much higher than those for the regular TCLP and water extraction tests.     

Treatment of Stormwater using Fibre Filter Media

In this study, a high-rate fibre filter was used as a pre-treatment to stormwater in conjunction with in-line flocculation. The effect of operating the fibre filter with different packing densities (105, 115 and 125 kg/m³) and filtration velocities (20, 40, 60 m/h) with and without in-line flocculation was investigated. In-line flocculation was provided using 5, 10 and 15 mg/L of ferric chloride (FeCl₃·6H₂O). The filter performance was studied in terms of pressure drop (ΔP), solids removal efficiency, heavy metals (total) removal efficiency and total organic carbon (TOC) removal efficiency. It is found that the use of in-line flocculation at a dose of 15 mg/L improved the performance of fibre filter as measured by turbidity removal (95%), total suspended solids reduction (98%), colour removal efficiency (99%), TOC removal (reduced by 30–40 %) and total coliform removal (93%). The modified fouling index reduced from 750–950 to 12 s/L² proving that fibre filter can be an excellent pre-treatment to membrane filtration that may be consider as post-treatment. The removal efficiency of heavy metal was variable as their concentration in raw water was small. Even though the concentration of some of these metals such as iron, aluminium, copper and zinc were reduced, others like nickel, chromium and cadmium showed lower removal rates.     

Ethanol washing of PAH-contaminated soil and Fenton oxidation of washing solution

As a means to remediate soil contaminated by polycyclic aromatic hydrocarbons, we investigated a combined process involving ethanol washing followed by a Fenton oxidation reaction. Artificial loamy soil was contaminated with various representative polycyclic aromatic hydrocarbons (i.e., fluorene, anthracene, pyrene, benzo(b)fluoranthene, or benzo(a)pyrene) at concentrations ten times higher than regulatory soil standards of The Netherlands or Canada, and then washed four times in ethanol, which reduced the concentration of polycyclic aromatic hydrocarbon contamination to below the regulatory standard. Fenton oxidation of ethanol solutions containing anthracene, benzo(a)pyrene, pyrene, acenaphthylene, acenaphthene, benz(a)anthracene, benzo(j)fluoranthene, or indeno(1,2,3-cd)pyrene showed a removal efficiency of 73.3%–99.0%; by contrast, solutions containing naphthalene, fluorene, fluoranthene, phenanthrene, or benzo(b)fluoranthene showed a removal efficiency of 9.6%–27.6%. Since each of the nonremediated polycyclic aromatic hydrocarbons, excluding benzo(b)fluoranthene, are easily biodegradable, these results indicate that the proposed treatment can be successfully applied to polycyclic aromatic hydrocarbon-contaminated soil that does not contain high concentrations of benzo(b)fluoranthene. The main reaction products resulting from Fenton oxidation of ethanol solutions containing anthracene or benz(a)anthracene were anthraquinon or benz(a)anthracene-7,12-dione, respectively; while 1,8-naphthalic anhydride was produced by solutions of acenaphthylene and acenaphthene, and 9-fluorenone by a fluorene solution. Received: June 9, 1998 / Accepted: March 24, 1999     

Metal leachability, heavy metals, polycyclic aromatic hydrocarbons and polychlorinated biphenyls in fly and bottom ashes of a medical waste incineration facility

Medical waste from hospitals and other healthcare institutions has become an imperative environmental and public safety problem. Medical waste in Greece has become one of the most urgent environmental problems, because there are 14,000 tons produced annually, of which only a small proportion is incinerated. In the prefecture of Attica there is only one modern municipal medical waste incinerator (started 2004) burning selected infectious hospital waste (5-6 tons day(-1)). Fly and bottom residues (ashes) are collected and stored temporarily in barrels. High values of metal leachability prohibit the landfilling of these ashes, as imposed by EU directives. In the present study we determined quantitatively the heavy metals and other elements in the fly and bottom ashes of the medical waste incinerator, by inductively coupled plasma emission spectrometry (ICP) and by energy dispersive X-ray analysis (EDAX). Heavy metals, which are very toxic, such as Pb, Cd, Ni, Cr, Cu and Zn were found in high concentrations in both fly and bottom ashes. Metal leachability of fly and bottom ashes by water and kerosene was measured by ICP and the results showed that toxic metals in both ashes, such as Pb, Cr, Cd, Cu and Zn, have high leaching values. These values indicate that metals can become soluble and mobile if ash is deposited in landfills, thus restricting their burial according to EU regulations. Analysis of polychlorinated biphenyls and polycyclic aromatic hydrocarbons in fly and bottom ashes showed that their concentrations were very low. This is the first known study in Greece and the results showed that incineration of medical waste can be very effective in minimizing the most hazardous and infectious health-care waste. The presence of toxic metals with high leachability values remains an important draw back of incineration of medical waste and various methods of treating these residues to diminish leaching are been considered at present to overcome this serious technical problem.     

Waste on the roadside, 'poi-sute' waste: its distribution and elution potential of pollutants into environment

Waste on the roadside, 'poi-sute' waste, was collected in a typical suburb in Japan (Ueda city, the sampling course: 3.2 km). The distribution, characterization of the 'poi-sute' waste and the loading of pollutants from the waste were studied. The average number of pieces of total waste was 690 pieces a month, and 220 pieces of waste were dumped a month per km. There was a tendency for much waste to be discarded around shops staying open until late at night. Regarding the sorts of the waste, cigarette butts are the most prevalent (the average was 150 cigarette butts/km/mo), and second was plastic materials. As for the weight, cigarette butts, plastics and papers were at a similar level (about 90 g/km/mo). The elution of arsenic (0.041 mg/L) and nicotine (3.8 mg/L) was ascertained by a dissolution test of 'poi-sute' cigarette butts obtained by sampling. Furthermore, the loading of heavy metals, such as lead, copper, chromium and cadmium, and polycyclic aromatic hydrocarbons (PAHs) from cigarette butts into the environment was confirmed. The load potentials of heavy metals were 0.020-1.7 mg/km/mo, and that of total-polyaromatic hydrocarbons was 0.032 mg/km/mo. These results indicate that the 'poi-sute' waste has a harmful influence on the environment.     

Leaching of heavy metals in acid mine drainage.

Acid mine drainage is one of the most serious environmental problems that the coal and metal mining industry is currently facing. The generation of low pH drainage enhances the dissolution of heavy metals in water. The samples used in this research originated from three pits at mine dumps. In a study reported in this paper, three types of tests; namely static test, kinetic test and column test were conducted to estimate acid generation and acid neutralization reaction rates, and to predict the solubility of metals and their release rates. Static test showed that all samples had a pH of net acid generation (NAG pH) <4, a net acid producing potential (NAPP) >10 kg H2SO4tonne(-1), and a S-content >3%, which can be classified as a high acid-forming capacity. Simulated runoff in the column tests was equivalent to 5-year average rainfall in Indonesia, the resultant leachates showed acidic behaviour (pH < 3.5). Based on the results, it was found that high mobilization of heavy metals (Cr, Cu, Zn, Cd and Pb) takes place under strong acidic conditions (pH approximately equal 2).     

Leaching behavior of heavy metals and PAHs from MSWI bottom ash in a long-term static immersing experiment

Bottom ash is the main solid residue (in weight) which is produced by municipal solid waste incineration (MSWI) facilities. This material is composed of a mineral matrix and may be used as secondary raw material for construction purpose. However, for this specific application the leaching behavior of the environmentally relevant elements under field conditions is different from the predicted behavior based on results obtained from the standardized leaching test. Therefore, a 70-day simulative experiment has been carried out in this study to investigate the release of major heavy metals (Cu and Pb) and polycyclic aromatic hydrocarbons (PAHs) from several particle fractions of bottom ash under a static leaching condition, where bottom ash was immersed in water at different initial pH values. Results showed that: (1) the leaching behavior of Cu and Pb was much similar with that depicted by the standardized leaching tests, and fit well with the solubility-controlling mechanism; (2) the sorption mechanism on the neoformed phases may control the solubility of Pb, whereas the dissolved organic carbon (DOC) may play an important role in the solubility of Cu; and (3) the leached PAHs were degraded during the later period of leaching process.     

Heavy metal content of combustible municipal solid waste in Denmark.

Data on the heavy metal composition of outlets from Danish incinerators was used to estimate the concentration of Zn, Cu, Pb, Cr, Ni, Cd, As and Hg in combustible waste (wet as received) at 14 Danish incinerators, representing about 80% of the waste incinerated in Denmark. Zn (1020 mg kg(-1)), Cu (620 mg kg(-1)) and Pb (370 mg kg(-1)) showed the highest concentration, whereas Hg (0.6 mg kg(-1)) showed the lowest concentration. The variation among the incinerators was in most cases within a factor of two to three, except for Cr that in two cases showed unexplained high concentrations. The fact that the data represent many incinerators and, in several cases, observations from a period of 4 to 5 years provides a good statistical basis for evaluating the content of heavy metals in combustible Danish waste. Such data may be used for identifying incinerators receiving waste with high concentrations of heavy metals suggesting the introduction of source control, or, if repeated in time, the data must also be used for monitoring the impacts of national regulation controlling heavy metals. It is recommended that future investigations consider the use of sample digestion methods that ensure complete digestion in order to use the data for determining the total heavy metal content of waste.     

Comparison of leaching characteristics of heavy metals from bottom and fly ashes in Korea and Japan

The objective of this research was to compare the leaching characteristics of heavy metals such as cadmium, chromium, copper, nickel, lead, etc., in Korean and Japanese municipal solid waste incineration (MSWI) ash. The rate of leaching of heavy metal was measured by KSLT and JTL-13, and the amount of heavy metals leached was compared with the metal content in each waste component. Finally, bio-availability testing was performed to assess the risks associated with heavy metals leached from bottom ash and fly ash. From the results, the value of neutralization ability in Japanese fly ash was four times higher than that in Korean fly ash. The reason was the difference in the content of Ca(OH)(2) in fly ash. The amount of lead leached exceeded the regulatory level in both Japanese and Korean fly ash. The rate of leaching was relatively low in ash with a pH in the range of 6-10. The bio-availability test in fly ash demonstrated that the amount of heavy metals leached was Pb>Cd>Cr, but the order was changed to Pb>Cr>Cd in the bottom ash. The leaching concentration of lead exceeded the Japanese risk level in all fly ashes from the two countries, but the leaching concentration of cadmium exceeded the regulatory level in Korean fly ash only.     

复合重金属污染高岭土的电动修复

根据电子废弃物拆解场地的污染特征,以复合重金属(Cu,Cd,Pb)污染高岭土为研究对象,考察了电动技术对污染土壤的修复效果。实验结果表明:在电压梯度为1 V/cm、阳极液为自来水、阴极液为柠檬酸-柠檬酸钠缓冲液(pH=5)、靠近阴极设置活性炭渗透反应墙(PRB)的条件下电动修复96 h后,Cu,Cd,Pb的平均去除率分别可达79.93%,99.43%,39.36%;土壤的酸碱性对电动修复效果影响显著,通过在阴极添加缓冲液维持土壤偏酸性条件,有利于重金属污染物的电动去除;在靠近阴极设置活性炭PRB可富集重金属,减少阴极液的污染;迁移率大的酸可提取态重金属较易去除,残渣态重金属稳定性强,去除率较低。     

重金属污染土壤生物毒性的发光菌法测定及评价

向土壤中人为投加重金属污染物,制备了重金属含量不同的一系列污染土壤,对土壤重金属浸提条件进行了探究,并应用明亮发光杆菌T3（Photobacterium phosphoreum T3）对单一Cu、Cd和Pb污染及Cu-Cd和Cu-Pb复合重金属污染土壤的生物毒性进行了测定。实验结果表明,土壤重金属的最佳浸提剂为0.1 mol/L HCl溶液,最佳浸提时间为2.0 h。在单一重金属污染条件下：Cu表现出低浓度促进生长、高浓度抑制生长的双重生物效应,而Cd和Pb则表现出浓度与生物毒性的正相关性;3种重金属污染土壤的毒性强弱顺序为Cd>Pb>Cu。在复合重金属污染条件下,由于重金属之间的相互作用,污染土壤的生物毒性增强。     

Heavy metal release from different ashes during serial batch tests using water and acid

Most ashes contain a significant amount of heavy metals and when released from disposed or used ash materials, they can form a major environmental concern for underground waters. The use of water extracts to assess the easily mobilisable content of heavy metals may not provide an appropriate measure. This study describes the patterns of heavy metal release from ash materials in context with results from the German standard extraction method DIN-S4 (DIN 38 414 S4). Samples of four different ashes (municipal solid waste incineration ash, wood ash, brown coal ash and hard coal ash) were subjected to a number of serial batch tests with liquid renewal, some of which involved the addition of acid to neutralize carbonates and oxides. Release of heavy metals showed different patterns depending on the element, the type of material, the method of extraction and the type of the extractant used. Only a small fraction of the total heavy metal contents occurred as water soluble salts; of special significance was the amount of Cr released from the wood ash. The reaction time (1, 24 or 72 h between each extraction step with water) had only a small effect on the release of heavy metals. However, the release of most of the heavy metals was governed by the dissolution processes following proton inputs, indicating that pH-dependent tests such as CEN TC 292 or others are required to estimate long-term effects of heavy metal releases from ashes. Based on the chemical characteristics of ash materials in terms of their form and solubility of heavy metals, recommendations were made on the disposal or use of the four ash materials.     

Size fractionation of organic matter and heavy metals in raw and treated leachate

This study characterized the organic matter and heavy metals in the leachate from two typical municipal solid waste (MSW) sanitary landfills in China, the recently established (3-year-old) Liulitun landfill and the mature (11-year-old) Beishenshu landfill, using a size fractionation procedure. The organic matter of all raw and treated leachate samples primarily existed in a truly-dissolved fraction with an apparent molecular weight (AMW) of <1 kDa, and its percentage decreased with an increase in overall AMW. The leachate from the newer landfill had a higher percentage of truly-dissolved organic matter. After anaerobic treatment, this leachate had a similar size fraction of organic matter to that seen for the raw leachate of the mature landfill. Biochemical processes had different removal efficiencies for various types of AMW organic matter, and the concentration of moderate AMW organic matter appeared to increase throughout these processes. Most of the heavy metals existed in a colloidal fraction (AMW >1 kDa and particle size <0.45 μm). The behaviors of different species of heavy metals had large variations. The size fractions of heavy metal species were significantly affected by treatment processes and landfill age, except for Zn. The concentration ratio of heavy metals to organic matter was maximal in the colloidal fraction and showed an inverse change to that seen for organic matter concentration changes caused by biochemical processes. Consequently, the pollution levels of heavy metals were substantially increased by treatment processes, although their concentrations decreased.     

Heavy metals fractionation before, during and after composting of sewage sludge with natural zeolite

The main limiting factor, in order to use compost in agriculture, is the total concentration of heavy metals. Natural zeolites, such as clinoptilolite, have the ability to take up and remove those metals by utilizing ion exchange. However, it is important to know about the fractionation of the heavy metals during the thermophilic phase and the maturation phase. The purpose of this work was to determine the changes in the fraction of heavy metals in sewage sludge compost in which clinoptilolite is used as a bulking agent to remove metals. The final result indicates that a significant (p < 0.05) percentage of the metals, which is not removed by the zeolite, is associated with the residual fraction which is considered as an inert form.     

Heavy metal speciation in various types of fly ash from municipal solid waste incinerator

Fly ash (FA) from municipal solid waste incinerators has been known as hazardous waste, which is mostly because of the high content of heavy metal and dioxins. Besides the content, the form of the heavy metals in fly ash is also very important, because it is tightly related with the leaching behavior of fly ash in diverse circumstances. To evaluate the environment potential risk of fly ash, the Tessier chemical extraction method was adopted. In this study, four kinds of fly ash were examined, one sample from China (CFA) and the other three from Japan (RFA, CaFA and NaFA). Five metal elements were detected and they were Ni, Cr, Cd, Pb, and Cu. The result of total heavy metals’ concentration showed CFA has the lowest content. As to the Tessier chemical extraction experiments, the results show that Cd, Pb, and Cu have higher leaching risk in the environment than other heavy metals. The result of leaching test experiment showed that the more exchangeable speciation of Cd, Cr and Pb in FA, the more it could leach out in natural environment.