Use of modified hydroxy-aluminum bentonites for chromium(III) removal from solutions

The retention of chromium(III) from a 2000ppm chromium basic sulfate and tannery waste solution at pH 4.5 using modified hydroxy-aluminum bentonites (OH-Al bentonites) as adsorbents was studied. OH-Al bentonite was prepared by mixing clay with a hydrolyzed commercial chlorohydroxy Al solution. The modified Al bentonites were obtained by (a) a treatment with 0.5M sodium chloride and (b) a treatment with a Na-hexametaphosphate solution (HMP) after adding sodium chloride. The effect of heating the adsorbents at 100, 500, 700 and 800 degrees C on Cr retention as a function of time was also analyzed. Cr retention by modified OH-Al bentonite with HMP increased with time (up to 100mgCr/g) where modified OH-Al bentonite was twice that of untreated bentonite. The relatively high uptake of metal from the salt solution by modified OH-Al bentonite treated at 800 degrees C, in which a complete interlayer collapse occurred, indicated the importance of the contribution of external surface sites to the retention capacity. The maximum Cr uptake from a water waste was 24mg/g, due to interferences and different chromium species in the industrial solution.     

农作物废料对海洋溢油吸附研究

根据海上围油栏围油原理,使用小型围油设备模拟出在围油栏除油后海上剩余溢油的质量M。收集稻壳、小米壳、小麦壳3种农作物废料作为吸油材料,室温下分别测出3种吸油材料对质量为M的溢油的饱和吸附时间。在吸附平衡的条件下,利用紫外分光光度计分别测出3种吸油材料吸附海水表面M质量溢油后的平衡吸附浓度ce。根据物理吸附理论,由平衡吸附浓度ce和平衡吸附量qe分别得出3种材料的Freundlich吸附等温式,从Freundlich吸附等温式比较了3种农作物废料的吸油性能。结果表明:稻壳的吸油性能最佳。     

Application of recycled paper sludge and biomass materials in manufacture of green composite pallet

Rice straw, rice husk and paper sludge are by-products and industrial waste, and are beneficial resources as raw biomass materials used for manufacturing value-added composite products. We investigated the effect on selected mechanical properties of adding rice straw, rice husk and paper sludge to wood composites to replace wood particles for manufacturing green pallets. Results showed that increasing the contents of rice straw and rice husk dramatically decreased the mechanical strength of the composites. This is because the wax and silicate coating of these materials obstructed the strong bonding with UF resin. When 10 wt.% of wood particle was replaced with 10 wt.% of paper sludge, the wood–paper sludge composites showed similar mechanical properties to those of wood particle. Wood particle can be replaced by 10 wt.% of dried paper sludge in accordance with the minimum requirement recommended by standards in green pallet manufacturing.     

Bioremediation of Acidic and Metalliferous Drainage (AMD) through organic carbon amendment by municipal sewage and green waste

Pit lakes (abandoned flooded mine pits) represent a potentially valuable water resource in hot arid regions. However, pit lake water is often characterised by low pH with high dissolved metal concentrations resulting from Acidic and Metalliferous Drainage (AMD). Addition of organic matter to pit lakes to enhance microbial sulphate reduction is a potential cost effective remediation strategy. However, cost and availability of suitable organic substrates are often limiting. Nevertheless, large quantities of sewage and green waste (organic garden waste) are often available at mine sites from nearby service towns. We treated AMD pit lake water (pH 2.4) from tropical, North Queensland, Australia, with primary-treated sewage sludge, green waste, and a mixture of sewage and green waste (1:1) in a controlled microcosm experiment (4.5 L). Treatments were assessed at two different rates of organic loading of 16:1 and 32:1 pit water:organic matter by mass. Combined green waste and sewage treatment was the optimal treatment with water pH increased to 5.5 in only 145 days with decreases of dissolved metal concentrations. Results indicated that green waste was a key component in the pH increase and concomitant heavy metal removal. Water quality remediation was primarily due to microbially-mediated sulphate reduction. The net result of this process was removal of sulphate and metal solutes to sediment mainly as monosulfides. During the treatment process NH(3) and H(2)S gases were produced, albeit at below concentrations of concern. Total coliforms were abundant in all green waste-treatments, however, faecal coliforms were absent from all treatments. This study demonstrates addition of low-grade organic materials has promise for bioremediation of acidic waters and warrants further experimental investigation into feasibility at higher scales of application such as pit lakes.     

Synthesis of mesoporous magnesium oxide: Its application to CO2 chemisorption

Mesoporous magnesium oxide (MgO) was synthesized using mesoporous carbon CMK-3 obtained from mesoporous SBA-15 as exotemplate. P123 was used as the structure-directing template and rice husk ash (RHA) as the silica source for the synthesis of SBA-15, which was subsequently treated with sucrose and sulphuric acid to obtain mesoporous carbon (CMK-3). X-ray powder diffraction (XRD) results and the type-IV adsorption isotherm with H1 hysteresis obtained by N₂ adsorption/desorption study for SBA-15, CMK-3 and mesoporous MgO suggests its resemblance with materials synthesized using conventional silica sources. Mesoporous MgO was subjected for CO₂ adsorption study in TGA; adsorption was 8 and 10 wt% at 25 and 100 °C, respectively. Finally, mesoporous MgO is selective to CO₂ gas, thermally stable and regenerable. Thus, this study contributes a better route to enhance CO₂ gas adsorption and use ecological waste rice husk for the synthesis of such efficient mesoporous materials.     

Study on assessment of slope stability and mixed disposal of overburden in voids of Singrauli Coalfield

The mining industry can be considered the backbone of the Indian economy as well as facilitating the power that drives most of the other industries in the company. The overburden and waste rocks produced during coal mining are major concerns in regard to the amount of land that is required for their disposal, as well as the stability of dumps for these materials, which are of increasing height. Land reclamation issues are also a concern. In this work the adverse impacts caused by the dumping of overburden on land and acidic mine water on water bodies is discussed. Remote sensing tools were used along with the laboratory experimentation to assess the various impacts. This study also shows that silt released from waste dumps, can affected the angle of repose of the overburden dump slope. The angle of repose of the overburden materials varies with particle size composition. Thus, use of in‐pit crushers in large opencast mining operations can effectively reduce the area locked under the waste dumps. The acid neutralization potential of fly ash and overburden for the treatment of acid water was tested in the laboratory by using fly ash and waste rock materials on acidic coalfield water. The results are encouraging, and fly ash may prove to be a good acid neutralizer when used in conjunction of coal overburden material.     

Kinetic and equilibrium isotherm studies for the adsorptive removal of Brilliant Green dye from aqueous solution by rice husk ash

The present study deals with the adsorption of Brilliant Green (BG) on rice husk ash (RHA). RHA is a solid waste obtained from the particulate collection equipment attached to the flue gas lines of rice husk fired boilers. Batch studies were performed to evaluate the influences of various experimental parameters like initial pH (pH0), contact time, adsorbent dose and initial concentration (C0) on the removal of BG. Optimum conditions for BG removal were found to be pH0 approximately 3.0, adsorbent dose approximately 6 g L(-1) of solution and equilibrium time approximately 5 h for the C0 range of 50-300 mg L(-1). Adsorption of BG followed pseudo-second-order kinetics. Intra-particle diffusion does not seem to control the BG removal process. Equilibrium isotherms for the adsorption of BG on RHA were analyzed by Freundlich, Langmuir, Redlich-Peterson (R-P), Dubnin-Radushkevich (D-R), and Temkin isotherm models using a non-linear regression technique. Langmuir and R-P isotherms were found to best represent the data for BG adsorption onto RHA. Adsorption of BG on RHA is favourably influenced by an increase in the temperature of the operation. Values of the change in entropy (DeltaS0) and heat of adsorption (DeltaH0) for BG adsorption on RHA were positive. The high negative value of change in Gibbs free energy (DeltaG0) indicates the feasible and spontaneous adsorption of BG on RHA.     

Enhancement of biomethane production from cattle manure with codigestion of dilute acid pretreated lignocellulosic biomass

It is well known that dilute sulfuric acid pretreatment of the lignicellulosisc biomass is an effective approach used for the production of the ethanol. However, there are less studies on the biogas production from the pretreated lignocellulosics and hardly data available on the codigestion of cattle manure with the pretreated lignocellulosisc material. The aim of this study was to evaluate biomethane production potential of codigestion of cattle manure with dilute acid pretreated lignocellulosic biomass. Sugarcane bagasse and rice husk was pretreated with dilute sulfuric acid or phosphoric acid at 121°C for 20 minutes and subsequently subjected to anaerobic digestion alone or codigested with cattle manure.

The results showed that codigestion of 1% phosphoric acid pretreated rice husk with cattle manure led to the highest methane production of 115 Nmlg^?1VS while monodigestion of cattle manure and phosphoric acid pretreated rice husk produced 98 and 87 Nmlg^?1VS, respectively. An inhibition was observed in anaerobic digestion of sulfuric acid pretreated rice husk and sugarcane bagasse during monodigestion and codigestion with cattle manure.

The study concludes that dilute phosphoric acid pretreated lignocellulosics like sugarcane bagasse and rice husk can be used as a cosubstrate with cattle manure in anaerobic digestion for enhanced methane production. Dilute sulfuric acid pretreatment, which is effective method for the bioethanol production, causes inhibition during anaerobic digestion of the pretreated lignocellulosics.     

Adsorption of Cu(II) ions from aqueous solutions on biochars prepared from agricultural by-products

In this study, the adsorption of Cu(II) from aqueous solutions by agricultural by-products, such as rice husks, olive pomace and orange waste, as well as compost, was evaluated. The aim was to obtain sorbent materials (biochars) through hydrothermal treatment (300?°C) and pyrolysis (300?°C and 600?°C). The effect of adsorbent dose, pH, contact time and initial Cu(II) concentration in batch-mode experiments was investigated. The optimum Cu(II) adsorption conditions was found to occur at 5-12?g/L adsorbent dose, initial pH 5-6, and reaction time 2-4?h. Furthermore, the adsorption kinetics were best described by the pseudo-second order model for all the tested materials, while the adsorption equilibrium best fitted by the linear and Freundlich isotherms. Comparing rice husks and olive pomace, the higher adsorption capacity resulted after pyrolysis at 300?°C. With respect to the orange waste and compost, the highest adsorption capacity was observed using biochars obtained after hydrothermal treatment and pyrolysis at 300?°C.     

Land application of biomass residue generated from palm oil processing: its potential benefits and threats

Man’s increased demand for food and better living conditions has led to over exploitation of resources and the consequent generation of enormous amounts of liquid and solid waste materials. This is one of the global challenges for mankind. In Malaysia, palm oil mill waste (POMW) contributes the highest proportion of industrial solid wastes produced yearly. Wastes from the mills include palm oil mill effluent, decanter cake, empty fruit bunches, seed shells and the fibre from the mesocarp. Direct application of POMW into agricultural soil has resulted in a number of problems such as water pollution, leaching. However, with application rates specific for targeted plant species, land application can be employed as a permanent solution to the problem of waste from palm oil mills. This review examines the characteristics of each of the palm oil wastes and their potential for use as a future fertilizer supplement.     

废钻井液对环境污染及固化处理室内研究

目前我国许多油田钻井井场位于稻田、麦田、虾池和鱼塘周围，而废钻井液中含有无机盐、重金属组分、油品及大量有机聚合物，其中有些是有害物质，一口井的废钻井液一般可达200～300m~3。这些废钻井液堆放在井场不进行处理会对周围环境造成较大污染。为此，如何处理这些废钻井液是目前令人极为关心的课题。本文分析了我国一些油田废钻井液的毒性；介绍了毒性提取、评价方法及其对土壤、植物和海洋生物的影响，同时重点介绍用化学固化方法处理废钻井液的结果。通过对现场的5个废钻井液的固化处理室内试验证实，废钻井液固化后有一定强度，其水浸出液清彻透明，达到排放标准，固化体可进行掩埋恢复地貌，也可作为建筑材料使用。     

A technical and investment analysis of intermediate-scale rice residue conversion systems

This paper describes the technical and economic factors affecting rice husk residue conversion to energy. A summary of the physical and chemical characteristics is provided, with an overview of the commercially available conversion systems. An analysis of two intermediate rice residue conversion systems is included to determine the most probable fuel requirements and financial/economic costs and benefits of both systems. Recommendations are presented regarding the conditions that must be present to ensure financial viability of these systems.     

酸改性活性炭在重金属与氨氮废水处理中的应用

重金属以及氨氮是造成水体污染的重要物质,在对水体重金属以及氨氮的去除方法中,活性炭吸附法有一定的进展.本文参照常见的酸类物质如硝酸、盐酸、硫酸、磷酸、柠檬酸和其他酸性物质对活性炭改性去除重金属和氨氮的研究,综述了各种酸改性的机理和对活性炭的影响,定性地比较了活性炭在各种酸改性后的去除能力.总结了对酸性改性活性炭在去除重金属和氨氮应用中的发展方向和前景,对于日后用酸性废水改性活性炭以达到以废治废的功效有着指导、借鉴作用.     

Improvement of soil quality after "alperujo" compost application to two contaminated soils characterised by differing heavy metal solubility

Reclamation of trace element polluted soils often requires the improvement of the soil quality by using appropriate organic amendments. Low quality compost from municipal solid waste has been tested for reclamation of soils, but these materials can provide high amounts of heavy metals. Therefore, a high-quality compost, with low levels of heavy metals, produced from the main by-product of the Spanish olive oil extraction industry ("alperujo") was evaluated for remediation of soils affected by a pyritic mine sludge. Two contaminated soils were selected from the same area: they were characterised by differing pH values (4.6 and 7.3) and total metal concentrations, which greatly affected the fractionation of the metals. Compost was applied to soil at two rates (equivalent to 48 and 72 Tm ha(-1)) and compared with an inorganic fertiliser treatment. Compost acted as an available nutrient source (C, N and P) and showed a low mineralisation rate, suggesting a slow release of nutrients and thus favouring long term soil fertility. In addition, the liming effect of the compost led to a significant reduction of toxicity for soil microorganisms in the acidic soil and immobilisation of soil heavy metals (especially Mn and Zn), resulting in a clear increase in both soil microbial biomass and nitrification. Such positive effects were clearly greater than those provoked by the mineral fertiliser even at the lowest compost application rate, which indicates that this type of compost can be very useful for bioremediation programmes (reclamation and revegetation of polluted soils) based on phytostabilisation strategies.     

污泥土地利用中重金属铜污染地下水的潜在风险研究

本研究旨在通过土柱淋溶实验来研究堆肥污泥土地利用后重金属铜的溶出性,以及对地下水的影响。结果表明:与去离子水相比,模拟酸雨(pH=4.5)会使土壤中Cu的淋溶强度增加,并更能促使其向下迁移。经长期淋溶后发现,淋出液中铜的浓度呈现有起伏的递减趋势,最高峰浓度达到0.0702mg/L,远低于地下水Ⅲ类标准(1.0mg/L),污泥土地利用后Cu对地下水的污染风险较小。     

Pyrolysis Investigation For Bio-Oil Production From Various Biomass Feedstocks In Thailand

This study investigated the bio-oil production from vacuum pyrolysis of potential biomass feedstocks in Thailand. Experiments were carried out on palm empty fruit bunch, rice straw, rice husk, eucalyptus wood, rubber wood (Hevea Brasiliensis), and Teng wood (Shorea Obtuse) in a lab-scale-fixed bed reactor. The results showed that the product distribution was strongly dependent on temperature and biomass properties. Maximum oil yields, i.e., 50–60 wt %, were reached at 450–550°C. Due to mild temperature, most of alkalis originally present in biomass concentrated in product char, and only traces were detected in oil. Two-third of energy in biomass was in the product oil.     

An analysis of future platinum resources,emissions and waste streams using a system dynamic model of its intentional and non-intentional flows and stocks

Platinum is increasingly used intentionally and non-intentionally in several applications. This has raised the concern about its future resources, emissions and losses during its life cycle. On the one hand, increasing platinum emissions might affect human health. On the other hand, the accumulated platinum in mineral waste, soil, landfill sites and construction materials as a result of the emissions, losses and the utilization of secondary materials can be seen as potential resources for platinum. This paper is aimed at (1) analyzing the long term impacts of the use of platinum intentionally and non-intentionally on its future demand and supply, release to the environment and accumulation in mineral waste, soil, landfill sites and construction materials and (2) quantifying the amount of platinum in secondary materials that would be available for platinum future supply. The analysis is carried out on a global level using a system dynamic model of platinum intentional and non-intentional flows and stocks. The analysis is based on four scenarios for the introduction of fuel cell vehicles (FCVs). The results show that platinum demand is increasing overtime in all scenarios at different rates and its identified resources are expected to deplete before the end of the century with or without the introduction of FCVs. The release of platinum to the environment and the accumulation in soil are expected to decrease when conventional ICE vehicles is replaced by FCVs. The amount of platinum accumulated in mineral waste, soil, landfill sites and construction materials by the time platinum is depleted are more than double its identified resources and would be potential resources for platinum that are available in different parts of the world. The methodology presented in this paper can be used in the assessment of other technologies and other metals.     

废钻井液固化实验研究

利用经实验筛选的固化剂配方对废钻井液进行了固化处理的室内配方研究。结果表明,经该固化剂配方处理后的固结材料在水中浸泡5d后的浸出液在色度、化学需氧量、pH值、石油类、悬浮物含量和重金属含量等指标方面可达到国家《污水综合排放标准》(GB8978-1996)中的二级标准。     

重量法测定含动、植物油和矿物油废水应注意的问题

废水监测中，用重量法测定污（废）水中的动、植物油和矿物油是常用方法之一。为了保证测试结果的准确性，减少误差，提高分析测试质量，作者以多年的实践经验结合塔里木油田采油厂生产污水和餐饮行业生活废水的测定，对测定两种不同含油类废水应注意的问题进行探讨。供同行在实际工作中参考。     

Effect of collection system on mineral content of biowaste

The EU is committed to encourage biological treatments of organic waste as an alternative to landfill and also to enhance organic matter recycling. When these wastes are composted, the composition of the initial raw materials is very important in order to obtain a good quality product. In this article, the mineral composition of the organic fraction obtained from source-sorted collection (SC) and the organic fraction mechanically separated (MS) from mass-collected municipal solid waste was evaluated. Also, the compositions of these 2 raw materials that are used in the current Spanish municipal solid waste biological treatment facilities were compared. The mineral elements analyzed were the total content of the heavy metals Zn, Cu, Ni, Cr, Pb and Cd, and the plant nutrients P, K, Na, Ca, Mg, Fe and Mn. The results obtained were expressed on dry matter basis and on mineral matter basis. Important differences were detected between SC and MS samples, on both dry and mineral matter basis. In general, nutrient contents are higher in SC than in MS, and heavy metal contents are significantly lower in SC. Our results also support the idea that the heavy metal migration from the non-compostable materials to the decomposable matrix takes place from the beginning of the process while both types of materials are in contact.