Simultaneous quantification of Bi(III) and U(VI) in environmental water samples with a complicated matrix containing organic compounds

Trace amounts of bismuth(III) and uranium(VI) can be simultaneously determined in a single scan by adsorptive cathodic stripping voltammetry in the presence of cupferron as a complexing agent. Optimal conditions were found to be: 0.1 mol?L^?1 acetate buffer (pH 5.3), 5?×?10^?5?mol?L^?1 cupferron, accumulation potential of ?0.25 V, and accumulation time of 30 s. The linear range of Bi(III) and U(VI) was observed over the concentration range from 2?×?10^?9 to 2?×?10^?7?mol?L^?1 and from 1?×?10^?8 to 5?×?10^?7?mol?L^?1, respectively. The influence of the main components of real water samples such as foreign ions and organic substances (surface active substances, humic substances) was precisely investigated. The method was applied to the simultaneous measurements of bismuth and uranium in natural water samples.     

A nanosilver-based spectrophotometric method for determination of malachite green in surface water samples

A new spectrophotometric method is reported for the determination of nanomolar level of malachite green in surface water samples. The method is based on the catalytic effect of silver nanoparticles on the oxidation of malachite green by hexacyanoferrate (III) in acetate–acetic acid medium. The absorbance is measured at 610 nm with the fixed-time method. Under the optimum conditions, the linear range was 8.0?×?10^?9–2.0?×?10^?7?mol?L^?1 malachite green with a correlation coefficient of 0.996. The limit of detection (S/N?=?3) was 2.0?×?10^?9?mol?L^?1. Relative standard deviation for ten replicate determinations of 1.0?×?10^?8?mol?L^?1 malachite green was 1.86 %. The method is featured with good accuracy and reproducibility for malachite green determination in surface water samples without any pre-concentration and separation step.     

Determination of hydrazine hydrate based on electrochemiluminescence of Ru(bpy) 3 2+

Considering of the basic properties and also the two nitrogen atoms in the structure, hydrazine hydrate was employed to be an amine additive candidate, to build a Ru(bpy) ₃ ²⁺ /hydrazine electrochemiluminescence (ECL) system, and ECL of Ru(bpy) ₃ ²⁺ has been employed for the determination of hydrazine hydrate in the paper. The result demonstrated that the logarithmic ECL increasing (ΔECL?=?ECL_{after addition of hydrazine}???ECL_{before addition of hydrazine}) versus the logarithmic concentration of hydrazine hydrate is linear over a concentration range of 1.0?×?10^?9 to 1.0?×?10^?5?mol/L, on both glassy carbon and Pt electrodes in a pH 9 phosphate buffer. The hydrazine hydrate detection limit was down to 1.0?×?10^?9?mol/L, comparatively lower than other detection methods. To check its applicability, the proposed method was applied to the determination of hydrazine hydrate added into a tap water sample with good reproducibility and stability. All these provide a possibility to develop a novel ECL detection method for hydrazine in water.     

The evaluation of the association constant between R-SN and Hg2+

The effective determination of heavy metals from environmental media is among the most important issues for many industrialized countries. The interaction between RS-N, as novel heavy metal probe, and metal ions was studied. RS-N shows selective color change from colorless to pink in the presence of Hg²⁺ in methanol/water solvent and the UV–Vis study shows peak at 560 nm. Fluorescence data revealed that the fluorescence enhance of RS-N by Hg²⁺ dramatically was the result of the formation of [Hg²⁺]RS-N complex. The effective association constants (K _a ) were 3.97?×?10⁵ and 0.204?×?10⁵ M^?1 for Hg²⁺ and Cu²⁺ to RS-N, respectively. The thermodynamic parameters, enthalpy change (ΔH ⁰) and entropy change (ΔS ⁰), were calculated to be ?6.431?±?0.226 kJ/mol and ?0.129?±?0.008 J/K/mol, respectively, according to van’t Hoff equation on the basis of Gibbs free energy (ΔG ⁰) ranged from ?33.8326 to ?28.5389 kJ/mol.     

Evaluation of applicability of the Sartorius Airport MD8 sampler for detection of Bacillus endospores in indoor air

This study was designed to evaluate the measuring range and lowest limit of detection of Bacillus endospores in the ambient room air when the Sartorius MD8 sampler, and two different culture methods for bacterial enumeration were used. Different concentrations of bioaerosol were generated inside the test chamber filled with either the high-efficiency particulate air (HEPA)-filtered air or with the ambient room air. The detection of endospores in the HEPA-filtered air was achievable: (1) when they were aerosolized at a concentration above 7.56?×?10³ CFU/m³ and analyzed with spread plate method, and (2) when they were aerosolized at a concentration above 4.00?×?10² CFU/m³ and analyzed with pour plate method. The detection of endospores in the ambient room air was possible: (1) when they were aerosolized at a concentration above 9.1?×?10³ CFU/m³ and analyzed with spread plate method, and (2) when they were aerosolized at a concentration above 5.6?×?10² CFU/m³ and analyzed with pour plate method. The microorganisms present in the ambient room air interfere with precise quantification of Bacillus endospores when their concentration is relatively low. The results of this study may be helpful in critical assessment of the results obtained from monitoring the air for bacterial endospores.     

Bioaccumulation and toxicity of arsenic in cyanobacteria cultures separated from a eutrophic reservoir

The bioaccumulation and toxicity of arsenate (arsenic (As)(V)) was studied using three cultures of cyanobacterial species—Oscillatoria tenuisa, Anabaena affinis, and Microcystis aeruginosa—that were isolated from a eutrophic reservoir. The As(V) uptake depended on the cyanobacterial species, the growth phase of the cyanobacteria, the duration of exposure, and the initial concentration of As(V). The specific growth rates of the three cultures immediately following the logarithmic phase were 0.033–0.041 L/day when the initial concentration of As(V) was 50 mg/L. These rates were 2.3–3.6 times less than those in the original culture medium without As(V). The rate of intake of As(V) in the logarithmic phase cultures greatly exceeded that in the stationary cultures. The accumulation of As(V) by the three cultures increased rapidly within 1 week from the initial value of 3.23?×?10^?2–5.40?×?10^?2 to 5.06?×?10^?1–6.73?×?10^?1 ng/cell in the logarithmic phase. The effective concentrations (EC₅₀) of As(V) for inhibiting the growth of the three cyanobacterial species growth of at 72 h followed the order Oscillatoria tenuisa (3.8 mg/L)?>?A. affinis (2.6 mg/L)?>?M. aeruginosa (1.2 mg/L). The cyanobacterial species that was most sensitive to As(V) was M. aeruginosa. Preliminary results from SEM-map studies suggest most of the As(V) in Microcystis aeruginosa accumulated in the cytoplasm (intercellular), while in O. tenuisa and A. affinis, a large proportion of As(V) bound to the cell wall (extracellular). These differences were understood with reference to the variation among the metabolic properties and morphological characteristics of the cyanobacterial species.     

New kinetic-spectrophotometric method for monitoring the concentration of iodine in river and city water samples

A new kinetic method has been developed for the determination of iodine in water samples. The method is based on the catalytic effect of I^? with the oxidation of Indigo Carmine (IC) by KBrO₃ in the sulfuric acid medium. The optimum conditions obtained are 0.16 M sulfuric acid, 1?×?10^?3 M of IC, 1?×?10^?2 M KBrO₃, reaction temperature of 35°C, and reaction time of 80 s at 612 nm. Under the optimized conditions, the method allowed the quantification of I^? in a range of 12–375 ng/mL with a detection limit of 0.46 ng/mL. The method was applied to the determination of iodine in river and city water samples with the satisfactorily results.     

Seasonal and spatio-temporal distribution of faecal-indicator bacteria in Tyume River in the Eastern Cape Province, South Africa

We assessed the incidence of faecal-indicator bacteria in Tyume River over a 12-month period between August 2010 and July 2011. Total coliforms, faecal coliforms and enterococci were determined by the membrane filtration method. Total coliforms were detected in counts ranging from 2.1?×?10² to 3.4?×?10⁴?CFU/100 ml. Faecal coliform counts ranged from 1?×?10² to 1.6?×?10⁴?CFU/100 ml while enterococci counts were in the range of 3.3?×?10¹ to 5.1?×?10³?CFU/100 ml. Indicator bacteria counts increased from upstream to downstream sampling sites. Counts of indicator bacteria at all sites were significantly affected by seasonal changes. The bacteriological qualities of the river water were poor, exceeding the guideline of 200 CFU/100 ml and 33 CFU/100 ml for faecal coliforms and enterococci, respectively, for recreational water. Faecal coliform counts also exceeded the 1,000 CFU/100 ml guideline for water used in fresh produce irrigation. Microbial source tracking results showed that faecal pollution was predominantly of human origin during spring at all sampling sites. During other seasons, human faecal pollution was largely confined to midstream and downstream sampling sites. Generally, the presence of faecal-indicator bacteria in the river water samples suggests faecal pollution of this freshwater resource, raising the possibility of the presence of pathogenic microorganisms in the water and a threat to public health.     

A very sensitive flow-injection spectrophotometric determination method for iron (II) and total iron using 2′, 3, 4′, 5, 7-pentahydroxyflavone

In this study, an ultra-sensitive and highly selective, rapid flow-injection spectrophotometric method for the determination of iron (II) and total iron has been proposed. The method was based on the reaction between iron (II) and 2′, 3, 4′, 5, 7-pentahydroxyflavone in slightly acidic solution with a strong absorption at 415 nm. The carrier solution used was 1?×?10^?5 M 2′, 3, 4′, 5, 7-pentahydroxyflavone in 0.1 M HAc/Ac^? buffer solution at pH 4.5. Parameters that affect simultaneously the determination of iron (II) and interfering ions were tested. The relative standard deviation for the determination of 50 μg L^?1 iron (II) was 0.85 % (n?=?10), and the limit of detection (blank signal plus three times the standard deviation of the blank) was 3 μg L^?1, both based on injection volumes of 20 μL. The method has been successfully applied to the determination of iron (II) and total iron in water samples and ore samples. The method was verified by analysing a certified reference material Zn/Al/Cu 43XZ3F.     

The potential of biogas production from municipal solid waste in a tropical climate

The objective of this study was to estimate the potential of organic municipal solid waste generated in an urban setting in a tropical climate to produce biogas. Five different categories of wastes were considered: fruit waste, food waste, yard waste, paper waste, and mixed waste. These fractions were assessed for their efficiency for biogas production in a laboratory-scale batch digester for a total period of 8 weeks at a temperature of 15–30 °C. During this period, fruit waste, food waste, yard waste, paper waste, and mixed waste were observed to produce 0.15, 0.17, 0.10, 0.08, and 0.15 m³ of biogas per kilogram of volatile solids, respectively. The biogas produced and caloric value of each feedstock was in the range of 1.25?×?10^?3 m³ (17 kWh)/cap/day (paper waste) to 15?×?10^?3 m³ (170 kWh)/cap/day (mixed waste). Paper waste produced the least (<1×10^?3(<17.8 kWh)/cap/day), and mixed waste produced the highest methane yield (10?×?10^?3 m³ (178 kWh)/cap/day). Thus, mixed waste was found to be more efficient than other feedstocks for biogas and methane production; this was mainly related to the better C/N ratio in mixed waste. Taking the total waste production in Jimma into account, the total mixed organic solid waste could produce 865?×?10³ m³ (5.4 m³/capita) of biogas or 537?×?10³ m³ (3.4 m³/capita) of methane per year. The total caloric value of methane production potential from mixed organic municipal solid waste was many times higher than the total energy requirement of the area.     

Application of cold-induced aggregation microextraction as a fast,simple, and organic solvent-free method for the separation and preconcentration of Se(IV) in rice and various water samples

The developed method is based on cold-induced aggregation microextraction of Se(IV) using the 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid as an extractant followed by spectrophotometry determination. The extraction of Se(IV) was performed in the presence of dithizone as the complexing agent. In this method, a very small amount of 1-butyl-3-methylimidazolium hexafluorophosphate was added to the sample solution containing Se-dithizone complex. Then, the solution was kept in a thermostated bath at 50 °C for 4 min. Subsequently, the solution was cooled in an ice bath and a cloudy solution was formed. After centrifuging, the extractant phase was analyzed using a spectrophotometric detection method. Some important parameters that might affect the extraction efficiency were optimized (HCl, 0.6 mol L^?1; dithizone, 4.0?×?10^?6 mol L^?1; ionic liquid, 100 μL). Under the optimum conditions, good linear relationship, sensitivity, and reproducibility were obtained. The limit of detection (LOD) (3S_b/m) was 1.5 μg L^?1, and the relative standard deviation (RSD) was 1.2 % for 30 μg L^?1 of Se(IV). The linear range was obtained in the range of 5–60 μg L^?1. It was satisfactory to analyze rice and various water samples.     

Radioactive Contamination Control by Atmospheric Dispersion Assessment of Airborne Indicator Contaminants: Numerical Model Validation

In this work, a numerical model is proposed to estimate air concentration of released airborne radioactive contaminants ¹³¹I and ¹³⁷Cs. A Gaussian dispersion model is used to assess the atmospheric dispersion of radioactive contaminants released continuously from a nuclear power plant as a result of an accident. The model uses various input parameters such as source height, release rate, stability class, wind speed, and wind direction. The validation of the model was carried out by comparing its predicted values with published experimental data. The model was extensively tested by simulating several accidental situations. The main conclusion drawn from these tests is that for large downwind distances from the release point, the contaminant concentrations predicted by the model diverge drastically from measured data, while for short distances, the predicted values generally agree quite well with experimental data. The obtained activity concentrations range from 1.57?×?10² to 6.43?×?10³ Bq/m³ for ¹³¹I and from 3.18?×?10^?2 to 9.72?×?10² Bq/m³ for ¹³⁷Cs. The estimated standard deviation coefficients values range of 7.2 to 6847.7 m, and the maximum absolute error predicted by the model for these parameters was less than 5%.     

Human health damage caused by particulate matter PM10 and ozone in urban environments: the case of Athens, Greece

Studies conducted over the past decades have provided substantial evidence that both the long- and the short-term exposures to ozone and particulate matter are responsible for mortality and cardiopulmonary morbidity. This paper examines the relationship between exposure to ambient concentrations of ozone (O₃) and particulate matter with aerodynamic diameter of less than 10 μm (PM₁₀) and public health and provides the quantification of the burden of disease from PM₁₀ and O₃-related mortality and morbidity through a Life Cycle Impact Assessment focused on the greater area of Athens, Greece. Thus, characterizations factors (CFs) for human health damage are calculated in 17 sites in Athens, in terms of the annual marginal change in the disability-adjusted life years (DALYs) due to a marginal increase in the ambient concentrations. It is found that the PM₁₀ intake factors range between 1.25?×?10^?6 and 2.78?×?10^?6, suggesting that 1.25–2.78 μg of PM₁₀ are inhaled by the Athenian population per kg of PM₁₀ in the urban atmosphere. Mortality due to chronic exposure to PM₁₀ has a dominant contribution to years of life lost with values ranging between 6.2?×?10^?5 and 1.1?×?10^?4. On the other hand, the mortality caused by short-term exposure to O₃ is weaker with the CFs ranging between 1.58?×?10^?7?years of life lost in the urban/traffic areas and 4.71?×?10^?7?years in the suburbs. Finally, it is found that 9,000 DALYs are lost on average in Athens, corresponding to 0.0018 DALYs per person. This is equal to 0.135 DALYs per person over a lifetime of approximately 75 years, assuming constant emission rates for the whole period.     

Synthesis and characterization of zeolites prepared from industrial fly ash

In this paper, we present the possibility of using fly ash to produce synthetic zeolites. The synthesis class F fly ash from the Stalowa Wola SA heat and power plant was subjected to 24 h hydrothermal reaction with sodium hydroxide. Depending on the reaction conditions, three types of synthetic zeolites were formed: Na-X (20 g fly ash, 0.5 dm³ of 3 mol?·?dm^?3 NaOH, 75 °C), Na-P1 (20 g fly ash, 0.5 dm³ of 3 mol?·?dm^?3 NaOH, 95 °C), and sodalite (20 g fly ash, 0.8 dm³ of 5 mol?·?dm^?3 NaOH?+?0.4 dm³ of 3 mol?·?dm^?3 NaCl, 95 °C). As synthesized materials were characterized to obtain mineral composition (X-ray diffractometry, Scanning electron microscopy-energy dispersive spectrometry), adsorption properties (Brunauer-Emmett-Teller surface area, N₂ isotherm adsorption/desorption), and ion exchange capacity. The most effective reaction for zeolite preparation was when sodalite was formed and the quantitative content of zeolite from X-ray diffractometry was 90 wt%, compared with 70 wt% for the Na-X and 75 wt% for the Na-P1. Residues from each synthesis reaction were the following: mullite, quartz, and the remains of amorphous aluminosilicate glass. The best zeolitic material as characterized by highest specific surface area was Na-X at almost 166 m²?·?g^?1, while for the Na-P1 and sodalite it was 71 and 33 m²?·?g^?1, respectively. The ion exchange capacity decreased in the following order: Na-X at 1.8 meq?·?g^?1, Na-P1 at 0.72 meq?·?g^?1, and sodalite at 0.56 meq?·?g^?1. The resulting zeolites are competitive for commercially available materials and are used as ion exchangers in industrial wastewater and soil decontamination.     

Utility of cefixime as a complexing reagent for the determination of Ni(II) in synthetic mixture and water samples

A simple, sensitive, and accurate UV spectrophotometric method has been developed for the determination of nickel in synthetic mixture and water samples. The method is based on the complexation reaction of nickel ion with cefixime, thus leading to the formation of Ni–cefixime complex in ethanol-distilled water medium at room temperature. The complex showed the maximum absorption wavelength at 332 nm. Beer’s law is obeyed in the working concentration range of 0.447–4.019 μg?mL^?1 with apparent molar absorptivity of 7.314?×?10³?L?mol^?1?cm^?1 and Sandell’s sensitivity of 0.008 μg/cm²/0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.016 and 0.054 μg?mL^?1, respectively. The factors such as cefixime concentration and solvent affecting the complexation reaction were carefully studied and optimized. The method is validated as per the International Conference on Harmonisation guideline. The method is successfully applied to the determination of Ni(II) in synthetic mixture and wadi water samples collected from Al Rustaq. The same water samples are also analyzed by atomic absorption spectrophotometry. Both methods determined the amount of Ni(II) in water sample and found to be approximately the same.     

Distributions, sources, and ecological risks of DDT-related contaminants in water, suspended particulate matter, and sediments from Haihe Plain, Northern China

The residual levels of dichlorodiphenyltrichloroethane (DDT) and its metabolites (DDXs, including p,p′-DDT, DDD, and DDE) in water, suspended particulate matter (SPM), and sediments from major rivers, lakes, and reservoirs in Haihe Plain were measured with a gas chromatograph equipped with a ⁶³Ni microelectron capture detector. In the fall of 2004, the contents of the total DDXs in the water and SPM were 0.29?±?0.69 ng L^?1 and 423.13?±?577.85 ng g^?1 dry wt., respectively. In the spring of 2005, the total DDXs were 0.36?±?0.91 ng L^?1 for water and 35.93?±?62.65 ng g^?1 dry wt. for SPM. The average concentration of DDXs for sediments was 7.10?±?7.57 ng g^?1 dry wt. during the two seasons. The Eastern-Hebei-Province Coastland River System was the most polluted, which was mainly attributable to the extensive use of DDT pesticide and dicofol in that system. Recent DDT inputs still occur in some regions, as indicated by DDT/(DDD + DDE) > 1 at 29–36 % of the sites for water and 55–61 % of the sites for SPM. The potential ecological risks of DDT in the water were assessed using a species sensitivity distribution model. Only shrimp and crabs were found to have potentially affected fraction values of 1.63?×?10^?3 to 2.27?×?10^?4, with probabilities beyond the hazardous concentration for 5 % of species (HC5) values of 1.90–2.56 %, suggesting only slight risks. DDXs in the sediments of some sites were also of potential risk to benthic organism based on consensus-based sediment quality guidelines.     

Occurrence of disinfection by-products in tap water distribution systems and their associated health risk

The concentrations of trihalomethanes (THMs), including chloroform, bromodichloromethane, dibromochloromethane, and bromoform, and haloacetic acids (HAAs; monochloroacetic acid, monobromoacetic acid, dibromoacetic acid, dichloroacetic acid, and trichloroacetic acid) were measured in tap waters passing through water distribution systems of six water treatment plants in Seoul, Korea, and their associated health risks from exposure to THMs through ingestion, dermal contact, and inhalation were estimated using a probabilistic approach. The concentration ranges for total THMs and HAA₅ were 3.9–53.5 and <LOD–49.5 μg/L, respectively. Among DBPs, chloroform, bromodichloromethane, dichloroacetic acid, and trichloroacetic acid were the most frequently detected. Spatial and seasonal variations in concentrations of THMs and HAAs in the six water distribution systems were significant (P?<?0.001).The mean lifetime cancer risks through ingestion, dermal contact, and inhalation during showering ranged as 7.23–10.06?×?10^?6, 2.19–3.63?×?10^?6, and 5.22–7.35?×?10^?5, respectively. The major exposure route to THMs was inhalation during showering. Sensitivity analysis showed that shower time and shower frequency had a great impact on the lifetime cancer risk by the exposure to THMs in tap water.     

Cloud point extraction–atomic absorption spectrometry for pre-concentration and determination of cadmium in cigarette samples

A new complexing agent, 2-((2-((1H-benzo[d]imidazole-2yl)methoxy)phenoxy)methyl)-1H-benzo[d]imidazole (BIMPI), was used in cloud point extraction and applied for selective pre-concentration of trace amounts of cadmium in cigarette samples. Cadmium was complexed with BIMPI in a buffer solution (pH?=?10) using Triton X-114 as surfactant and quantitatively extracted into a small volume of the surfactant-rich phase after centrifugation. Under optimized conditions (pH?=?10.0, 0.8?×?10^?4?mol?L^?1 BIMPI and 0.08 % (w/v) Triton X-114), calibration graph was linear in the range of 34.0–1,670.0 μg?L^?1. The proposed method was applied to the determination of Cd in various cigarette (tobacco) samples which gave satisfactory results.     

Voltammetric determination of platinum at a lead film electrode in environmental water samples

The paper presents the first report on the application of a lead film electrode for the determination of ultratrace concentrations of platinum. The procedure is based on preconcentration of the Pt(IV)-formaldehyde complexes at an in situ plated lead film electrode held at ?0.9 V (vs. Ag/AgCl), followed by a negatively sweeping differential pulse voltammetric scan. The composition of the supporting electrolyte, the influence of accumulation potential and time on the sensitivity of platinum responses are discussed. The detection limit of Pt(IV) with the accumulation time of 60 was equal to 9.2?×?10^?12 mol L^?1. The application of this method was tested by recovery of Pt(IV) from spiked environmental water samples.     

Polycyclic aromatic hydrocarbons in soils from Urumqi, China: distribution, source contributions, and potential health risks

Concentrations of 16 priority polycyclic aromatic hydrocarbons (PAHs) were measured in 28 surface soils samples collected from Urumqi, northwest China, for examination of distributions, source contributions, and potential health effects. The results indicated that the sum of 16 PAHs concentration ranged from 331 to 15,799 μg?kg^?1 (dw) in soils, with a mean of 5,018?±?4,896 μg?kg^?1 (n?=?28). The sum of seven carPAHs concentration ranged from 4 to 1,879 μg?kg^?1 (dw; n?=?28). The highest ∑PAHs concentrations were found at roadsides and industrial sites, followed by those at parks, rural areas, and business/residential areas. Coal combustion, emission of diesel and gasoline from vehicles, and petroleum source were four sources of PAHs as determined by PMF analysis, which contributed 51.19, 19.02, 18.35, and 11.42 % to the PAH sources, respectively. Excellent coefficients of correlation between the measured and predicted PAHs concentrations suggested that the PMF model was very effective to estimate sources of PAHs in soils. Incremental lifetime cancer risk values at the 95th percentile due to human exposure to surface soils PAHs in Urumqi were 2.02?×?10^?6 for children and 2.72?×?10^?5 for adults. The results suggested that the current PAHs levels in soils from Urumqi were pervasive and moderately carcinogenic to children and adults.