生物强化技术处理难降解有机污染物的研究进展

阐述了生物强化技术的原理，概括了旧内外有关生物强化技术处理难降解有机污染物的应用实例及效果。介绍了生物强化技术应用中有关高效降解菌和生物强化菌剂的研究与开发现状，进一步讨论了应用生物强化技术的主要控制参数，展望了生物强化技术的发展方向。     

四溴双酚A降解技术的研究进展

综述了微生物、物理和化学降解技术等几种主要的四溴双酚A（TBBPA）降解技术的研究进展。阐述了各种降解技术的机理和优缺点。指出今后重点的研究方向是：根据不同的反应机理和生长特性分离出微生物降解TBBPA的优势菌种，探索将TBBPA彻底碳化的工艺条件;优化高级氧化法降解TBBPA的反应条件，使之更适于工程应用;将还原法与微生物降解技术或高级氧化法相结合，先将TBBPA快速还原成双酚A，再进一步彻底碳化成CO2和H2O。     

氰化物污染土壤微生物修复方法初步研究

利用经过筛选和驯化的降氰菌处理氰化物污染土壤,实现氰化物的降解和去除,据此建立降氰菌修复含氰土壤的新方法。结果表明,降氰菌处理效果快速有效,经过3 d生物培养,氰化物降解率达到31.2%;随着培养时间延长,微生物群落代谢能力发生变化,在第3~8 d氰化物降解率增长缓慢,在第8 d达到33.3%。通过降氰菌种资源的筛选和应用,为氰化物污染土壤的修复提供了清洁、经济、有效的技术思路。     

萘降解菌的筛选及其对多环芳烃的降解

从柴油污染土壤中筛选分离出一株萘降解菌N-3,进行了菌种鉴定及萘双加氧酶基因(nah)验证,并考察了该菌对不同种类多环芳烃(PAHs)的降解能力及降解过程中脱氢酶活性的变化。实验结果表明:该菌为铜绿假单胞菌(Pseudomonas aeruginosa),含有nah基因;当分别对液体培养基中质量浓度为50 mg/L的萘、菲、蒽、芘、芴降解84 h时,菌株N-3对萘、菲、蒽、芘、芴的降解率分别为28.81%,34.83%,36.65%,27.50%,23.47%。菌株N-3的脱氢酶活性与其对不同PAHs的降解率呈一定的正相关性。该菌不仅能有效降解萘,且对其他种类PAHs也有一定降解作用。     

生物强化技术处理化纤废水

采用生物强化技术,即利用从废水中分离、筛选出的降解丙烯腈与总氰的特效菌株,使化纤废水加营养盐的培养基中丙烯腈降解率达98．7％,总氰降解率达84％。将分离到的特效菌株进行混合培养,其降解丙烯腈与总氰的最佳体积比为1．0：（1．5～2．0）。使用该技术不必改变化纤废水处理场原有工艺。     

降解多环芳烃的微生物的分离、鉴定方法及应用

阐述了降解多环芳烃的微生物的分离和鉴定方法；介绍了多环芳烃降解微生物的驯化方式；综述了多环芳烃降解菌的应用研究情况；对消除环境中多环芳烃污染问题的相关研究进行了展望并指出了将实验室筛选分离到的多环芳烃高效降解菌应用到实际环境中需解决的主要问题。     

微生物降解有机磷农药的研究进展

利用微生物及其酶降解有机磷农药行之有效。以乐果、甲基对硫磷、甲胺磷、杀螟硫磷和毒死蜱为有机磷农药的代表，从可降解这些有机磷农药的微生物的筛选、基因工程菌的构建、生物降解酶的研究及其应用3个方面进行了综述，指出了未来的研究方向。     

土壤氰化物污染生物修复技术研究进展

综述了植物修复、微生物修复和生物联合修复等土壤氰化物污染生物修复技术的降解机理、降解途径及降解影响因素的研究进展,探讨了氰化物生物修复技术的发展趋势和应用前景。指出基于提高修复时效和针对土壤复合污染类型的多技术融合研究、基于提高微生物耐受性和降解效率的菌株固定化及菌根真菌-植物联合技术研究以及基于工程化应用为导向的现场试验研究是未来研究的重点领域,为土壤氰化物污染的综合治理和修复提出了新思路。     

对苯二甲酸降解菌固定化生物流化床处理精对苯二甲酸废水

采用微生物筛选、纯化技术，获得了降解对苯二甲酸（TA）的YPC—TA1，YPC—TA2，YPC-TA3，YPC—TA44株菌株。将筛选出的TA降解菌固定化，处理初始TA质量浓度为2650mg／L的模拟废水，降解36h后TA去除率达100％。用TA降解芮在生物流化床反应器中处理PTA废水，最佳容积负荷为6.7kg／（m^3·d）。生物流化床反应器可在容积负荷为6．0～6．5kg／（m^3·d）的较佳条件下长周期稳定运行，COD去除率保持在91％左右，TA去除率保持在94％左右。低pH废水冲击和高容积负荷废水冲击时COD，TA去除率均明显下降，恢复正常讲水后3～4d，COD，TA去除率均恢复正常。     

一株双酚A降解菌的筛选、鉴定及其生长、降解条件

从沈阳北部污水处理厂曝气池活性污泥中驯化、分离及筛选得到一株以双酚A为唯一碳源的高效降解菌株D-17,通过菌体形态、生理生化反应特性及16S r DNA基因测序分析对其进行了鉴定,并研究了该菌株的生长及双酚A降解条件。菌种鉴定结果表明,该菌为乙酸钙不动杆菌(Acinetobacter calcoaceticus)。实验结果表明:该菌株的生长及降解双酚A的最适条件为溶液pH 7.0,接种量10%,摇床转速150 r/min,降解温度30℃,降解时间5d;当双酚A初始质量浓度为60 mg/L时,双酚A降解率达52.62%;投加蛋白胨后,双酚A降解率提高至57.15%。     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

富拉尔基发电总厂200MW机组除尘器改造

对富拉尔基发电总厂5号炉的设计条件进行了分析，针对燃用低硫煤，飞灰比电阻高，场地较小，除尘效率要求高的情况，在电除尘器的设计上采取有效措施，达到了排放要求。     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

Effect of Degree of Substitution of Octenyl Succinate Starch on Enzymatic Degradation

Octenyl succinate starch of degree of substitution (ds) 0.03, 0.07, and 0.11 was synthesized in an aqueous medium. These compounds were then tested for the susceptibility to enzymatic degradation. The multiple-enzyme regime of -amylase, amyloglucosidase, and pullulanase was chosen for the evaluation. This combination of enzymes had been proven to degrade 99.5% of unmodified starch to glucose and hence was chosen for this study. It was found that even small amounts of subsituent caused a considerable decrease in the extent of degradation. The net extent of degradation decreased with increasing ds. Surprisingly, the amount of glucose from all three substituted substrates was quite similar, suggesting the effect small amounts of subtituent had on the enzymatic activity.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

袋式除尘器气流分布数值计算研究

采用结构化/非结构化混合网格技术、多孔介质模型及k-ε两方程湍流模型,对某袋式除尘器及进出口管道内的气体流场进行了数值计算.计算结果表明,合理布置导流板后,袋式除尘器两箱体流量偏差为1.8％;除尘器下游滤袋单元处理气量偏大,中游滤袋单元处理气量较小,最大流量与最小流量偏差为22.3％；靠近除尘器进口处灰斗内存在气流回流特性,易造成粉尘的二次附着现象.     

Kinetics of Hydrolytic Degradation of PLA

The chemical recycling of poly(lactic acid) (PLA) to its monomer is crucial to reduce both the consumption of renewable resources for the monomer synthesis and the environmental impact related to its production and disposal. In particular, the production of lactic acid from PLA wastes, rather than from virgin raw materials, it is also possible to achieve considerable primary energy savings. The focus of this work is to analyse deeply the PLA hydrolytic decomposition by means of a kinetic model based on two reactions mechanism. To this end, new experimental data have been gathered in order to investigate a wider temperature range (from 140 to 180 °C) and to extend the water/PLA ratio up to 50 % of PLA by weight. The reported results clearly highlight that more than 95 % of PLA is hydrolyzed to water-soluble lactic acid within 120 min, when it is hydrolyzed within 160–180 °C. Furthermore, the kinetic constant is highly influenced by reaction temperature. The proposed “two reactions” kinetic mechanism complies satisfactorily with the experimental data under analysis.     

Effects of temperature on the release of nutrient elements of solid organic materials under conditions of oversaturation

The effects of temperature on the release of chemical components of six solid organic materials under conditions of oversaturation were investigated in this paper. The six materials were peat moss (PM), weathered coals (WC), charred rice husks (CRH), sawdust (Sd), turfgrass clippings (TC), and chicken manure (CM). Significant differences were observed in the available nitrogen and phosphorus content of the aqueous extracts of organic materials at different temperatures. The available nitrogen content in aqueous extracts of PM and WC at 25 °C was higher than that registered at 15 °C and 35 °C. Available nitrogen content in the aqueous extracts of CRH, Sd, TC, and WC at 35 °C was higher than at 15 °C and 25 °C. The available phosphorus content in the aqueous extracts of organic materials at 35 °C was higher than that available at 15 °C and 25 °C, with the exception of Sd. In addition, the release of available phosphorus in the aqueous solution of organic materials at different temperatures varied constantly for 108 h. The release of potassium (K⁺) and sodium (Na⁺) ions in the aqueous extracts of organic materials was basically steady over time, with the exception of CM. High temperature (35 °C) may significantly hasten the release of K⁺ from organic substrates (except for WC) with low temperatures significantly inhibiting release of K⁺ in Sd and CRH. High temperatures (35 °C) might significantly facilitate the release of Na⁺ in CM and TC. However, no significant differences were manifested in the release of Na⁺ from organic substrates at different temperatures, with the exception of CM and TC. Moreover, no significant differences were observed in the release of calcium, magnesium and iron ions with time, nor were there any significant differences in the contents of iron ions in the aqueous extracts of organic materials at different temperatures. The results indicate that multiple mediums should be pretreated in water for a week before being used for planting. They should be used when all mineral elements of organic materials are steady and ignoring the effect of organic mediums.