生物膜细菌藻酸盐对Cu2+的吸附动力学研究

以生物膜中提取的细菌藻酸盐为原料制备藻酸钙为吸附剂,对水溶液中的Cu2+进行了吸附动力学研究.试验结果表明,吸附时间、溶液初始pH和吸附剂投加量对藻酸钙吸附Cu2+影响显著.当溶液初始pH为4.0、Cu2+初始质量浓度为100 mg/L、吸附剂投加量为0.7 g/L时,藻酸钙对Cu2+的平衡吸附量为56.15 mg/g.水溶液中Cu2+在藻酸钙上的吸附动力学过程可用准二级动力学方程来模拟.吸附等温线研究表明,藻酸钙吸附Cu2+的过程可用Langmuir和Freundlich模型来描述.100 mmol/L 乙二胺四乙酸(EDTA)可有效解吸95.6%的Cu2+,实现Cu2+的回收与吸附剂的重复利用.     

核桃壳对模拟废水中Cu~(2+)的吸附性能研究

采用核桃壳作为吸附剂,对模拟废水中的Cu2+进行吸附去除,考察了吸附剂粒径、水样初始pH、吸附剂用量、Cu2+初始浓度、吸附时间等因素对Cu2+吸附效果的影响,确定最佳吸附参数,并进行了吸附动力学和吸附等温线分析。结果表明:最佳吸附参数为核桃壳吸附剂粒径1.25~1.60mm、水样初始pH 5.0、吸附剂用量2.5g,Cu2+初始质量浓度20mg/L、吸附时间360min,在此条件下100mL水样在200r/min、25℃条件下吸附的Cu2+去除率达70%以上,吸附量约为0.702mg/g;本实验过程采用伪二级动力学方程的拟合更好,R2均在0.9以上,Cu2+吸附速率与其浓度的二次方成正比;Langmuir方程可以较好地描述核桃壳吸附剂对Cu2+的吸附过程,此吸附过程是单分子层的吸附。     

交联壳聚糖对铀的吸附研究

以壳聚糖(CTS)为原料,在碱性条件下用环氧氯丙烷对壳聚糖进行化学改性,制得不溶水的交联壳聚糖(CCTS)。利用CCTS吸附铀(UO22+),探讨吸附动力学规律以及初始浓度,pH值的影响。实验结果表明,CCTS对UO22+的吸附符合Langmu ir吸附等温模型,并能用准二级速率方程对吸附动力学加以描述。当在CCTS为10 mg,pH为3,UO22+初始浓度为50μg/mL条件下,CCTS对UO22+的吸附去除率为98%以上。     

皂化改性橘子皮生物吸附剂对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、氢氧化钠处理,得到改性橘子皮生物吸附剂SOP,将其用于对重金属离子Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的吸附。研究了溶液pH、吸附时间和重金属离子初始浓度对SOP吸附性能的影响。结果表明,重金属离子在生物吸附剂上的吸附速率快,符合准二级动力学方程。SOP对重金属离子的吸附等温线符合Lang-muir模型,根据Langmuir模型计算SOP对Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为56.82、152.4、66.27、33.90和23.02 mg/g,均高于改性前。常见阳离子的存在对重金属离子吸附的影响较小,改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂。     

改性棉铃壳对水中刚果红的吸附性能

通过甲醇酯化制备改性棉铃壳吸附剂,利用红外光谱仪、扫描电镜等表征了改性前后棉铃壳表面结构和官能团变化情况,考察了改性棉铃壳投加量、刚果红初始浓度和溶液pH等因素对改性棉铃壳吸附水中刚果红的性能影响,并通过实验分析了改性棉铃壳对水中刚果红吸附动力学。结果表明,改性后棉铃壳表面官能团明显改变,表面光滑、致密。改性棉铃壳对刚果红的吸附效果较未改性棉铃壳明显提高,增加刚果红初始浓度和吸附时间可以增加改性棉铃壳对刚果红的吸附量。在溶液pH为6、吸附剂投加量为20 g·L-1,吸附时间为120 min时,刚果红的去除率可达79.1%。改性棉铃壳对刚果红的吸附过程符合Lagergren准二级动力学模型,吸附过程属于化学吸附,吸收速率受表面扩散和颗粒内扩散控制。     

聚甲亚胺酰胺树脂对水中Cu~(2+)的吸附

制备了聚甲亚胺酰胺树脂,对其进行傅里叶变换红外光谱分析。采用批处理方法实验了pH、铜离子初始浓度、吸附时间、吸附剂用量对吸附量的影响,研究了等温吸附模型和吸附动力学模型。优化后的吸附条件为:在铜离子溶液体积50 mL、初始浓度为300 mg/L、pH为6.0时,吸附剂投放量50 mg、吸附时间60 min,此时吸附量达到269.1 mg/g,去除率达89.7%。25℃时在研究浓度范围内,铜离子吸附过程用Langmuir等温线模型和Freundlich等温线模型描述均可;与准一级动力学方程、Elovich方程及内扩散方程相比,准二级动力学方程能更好地描述其吸附动力学过程。     

橘子皮皂化交联改性及其对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、NaOH和CaCl2处理,得到皂化交联改性橘子皮(SCOP)生物吸附剂,将其用于对重金属离子Cu2+、pb2+、Cd2+、Zn2+和Ni2+的吸附,并研究了溶液pH、吸附时间和重金属离子初始浓度对SCOP吸附性能的影响.结果表明,重金属离子在改性橘子皮上的吸附速率快,符合准二级动力学方程；改性橘子皮对Cu2+、pb2+、Zn2+和Ni2+的吸附等温线符合Langmuir方程,对Cd2+的吸附等温线符合Freundlich方程,根据Langmuir方程计算对Cu2+、pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为72.73、209.80、85.84、56.18、33.80mg/g,均高于改性前.改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂.     

花生壳、大豆壳和柚子皮对Cr3+、Cu2+和Ni2+的吸附研究

采用农林废弃物花生壳、大豆壳、柚子皮对重金属离子Cr3+、Cu2+和Ni2+进行吸附研究,探讨反应时间、吸附剂用量、pH、重金属离子初始浓度以及温度对吸附的影响.结果表明:柚子皮对Cr3+、Cu2+、Ni2+的吸附效果优于花生壳和大豆壳,其在20℃、pH 5.00、10.0 mg/kg条件下,反应360 min,Cr3+、Cu2+、Ni2+的吸附率分别可达83.20％、84.50％、59.10％;花生壳、大豆壳和柚子皮对Ni2+的吸附率远低于Cr3+和Cu2+；花生壳、大豆壳和柚子皮对Cr3+、Cu2+、Ni2+的吸附动力学可以用准二级动力学方程描述；吸附率随初始重金属离子浓度增加而降低,其吸附等温线可以用Langmuir方程描述；在一定范围内,吸附率随吸附剂用量增加而增加；溶液初始pH在2～5时,吸附率随pH增大而增加；Cu2、Ni2+的吸附量随温度的上升而逐渐减少,但Cr3+的吸附量随着温度的上升而略增加.     

改性硅胶对水溶液中Pd2+的吸附

采用氨基硫脲对硅胶进行改性并表征,探讨了改性硅胶(SG-TSC)对水溶液中Pd2+的吸附性能。实验考察了p H值、吸附剂质量、吸附时间以及Pd2+初始浓度等因素对吸附的影响,并探讨了SG-TSC对Pd2+吸附动力学及等温吸附特性。结果表明:在p H为3~6范围内,吸附效果最好。吸附平衡时间为90 min,吸附动力学符合二级速率方程,颗粒内扩散与液膜扩散共同影响着吸附过程。Langmuir等温吸附方程能较好地描述Pd2+在SG-TSC上的吸附特性,298 K时静态饱和吸附容量为0.105 mmol/g。热力学参数计算结果表明,SG-TSC吸附水溶液中的Pd2+是自发、吸热和熵值增加的过程。     

改性甘蔗渣对Cu2+和Zn2+的吸附机理

研究了均苯四甲酸二酐(PMDA)和乙二胺四乙酸二酐(EDTAD)改性甘蔗渣对重金属离子Cu2+和Zn2+的吸附性能,包括吸附动力学和吸附等温线。结果表明,改性后的甘蔗渣对重金属离子Cu2+和Zn2+的吸附容量有显著提高,对Cu2+和Zn2+吸附等温线均符合Langmuir方程,吸附为单分子层吸附。根据Langmuir方程,PMDA和EDTAD改性甘蔗渣对Cu2+的吸附量分别为60.21和33.45 mg/g,对Zn2+的吸附量分别是70.53和36.53 mg/g。两种改性甘蔗渣对两种金属离子的吸附在30 min内均可完成,用准二级吸附动力学方程模拟动力学过程得到较好的线性相关性。以EDTA溶液为洗脱剂对吸附Cu2+和Zn2+的改性甘蔗渣进行洗脱再生,再生的吸附剂可反复使用。     

矸石基X型分子筛对水中Co2+、Cu2+、Cd2+和Cr3+的去除

以煤矸石为原料,采用碱熔后水热合成法制备X型分子筛并进行XRD、SEM、BET和Zeta电位分析。研究其对水中Co2+、Cu2+、Cd2+和Cr3+4种离子的吸附性能,包括吸附等温线、吸附动力学以及初始金属离子浓度、pH值对吸附性能的影响。所合成的矸石基X型分子筛的BET比表面积为676.02 m2/g,微孔孔容为0.263 cm3/g。吸附实验表明,矸石基X型分子筛能有效去除上述4种离子,同时实现煤矸石的资源化和金属离子的去除。4种离子的平衡吸附量均随初始浓度的增大而增大,相同条件下平衡吸附量的大小顺序为Cd2+>Cr3+>Cu2+>Co2+。准二级动力学模型能很好地描述4种离子的吸附动力行为。Langmuir模型对Co2+、Cu2+和Cd2+吸附的拟合较Freundlich模型高,说明其主要表现为物理吸附过程。4种离子的吸附速率均由液膜扩散和颗粒内扩散共同控制。     

硅烷化改性沸石对重金属离子的吸附性能

制得一种用于重金属废水处理的新型硅烷化改性沸石吸附剂,成本低、效果显著且稳定。通过对改性沸石表征,分析了改性对沸石结构的影响。结果表明,改性一定程度降低了原沸石的晶体特征,但基本上保持了其结构组成;硅烷化改性成功地在沸石上接枝了氨基。对硅烷化沸石的特性研究,得出硅烷化沸石对Ni2+、Cu2+、Zn2+和Pb2+吸附最佳投加量为1、1、1.6和0.6 g/L,且此时对4种离子的去除率也较好;吸附动力学研究得出,其吸附过程可用二级动力学方程较好地拟合;吸附达到平衡时,4种金属离子的平衡吸附量分别为11.23、17.41、15.45和59.42 mg/g;硅烷化沸石对金属离子的吸附行为更符合Langmuir模型,为化学吸附;在酸性条件下(pH=2～6),硅烷化沸石仍保持一定的吸附能力,具有一定的耐酸性。     

改性玉米秸秆吸附Cu2+的动力学和热力学

本研究用ZnCl2作为活化剂,使用功率640 W的微波照射4 min的方法制备改性玉米秸秆。考察投加量、pH、吸附时间对吸附性能的影响,并对等温吸附特征、吸附动力学和热力学进行了系统研究。结果表明:投加量为0.2 g,pH为6,改性玉米秸秆对Cu2+具有很好的吸附效果,吸附在8 h后达到平衡。该吸附过程符合Langmuir及Freundlich等温吸附模型和准二级动力学方程,其反应的吉布斯自由能△G<0,为自发反应过程。     

Copper (II) adsorption by the extracellular polymeric substance extracted from waste activated sludge after short-time aerobic digestion

The extracellular polymeric substance (EPS) extracted from waste activated sludge (WAS) after short-time aerobic digestion was investigated to be used as a novel biosorbent for Cu²⁺ removal from water. The EPS consisted of protein (52.6 %, w/w), polysaccharide (30.7 %, w/w), and nucleic acid (16.7 %, w/w). Short-time aerobic digestion process of WAS for about 4 h promoted the productivity growth of the EPS for about 10 %. With a molecular weight of about 1.9?×?10⁶ Da, the EPS showed a linear structure with long chains, and contained carboxyl, hydroxyl, and amino groups. The sorption kinetics was well fit for the pseudo-second-order model, and the maximum sorption capacity of the EPS (700.3 mg Cu²⁺/g EPS) was markedly greater than those of the reported biosorbents. Both Langmuir model and Freundlich model commendably described the sorption isotherm. The Gibbs free energy analysis of the adsorption showed that the sorption process was feasible and spontaneous. According to the complex results of multiple analytical techniques, including scanning electron microscopy, Fourier transform infrared spectroscopy, atomic force microscopy, etc., the adsorption process took place via both physical and chemical sorption, but the electrostatic interaction between sorption sites with the functional groups and Cu²⁺ is the major mechanism.     

4种脂肪多胺修饰硅胶对铅离子的吸附

为了合成高效铅离子吸附剂,了解其对铅离子的吸附规律。采用(3-氯丙基)三甲氧基硅烷(CPTS)架桥法,以硅胶(SG)为载体,乙二胺(EDA)、二乙烯三胺(DETA)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)为表面修饰剂,合成了4种胺化硅胶,测定了它们的红外光谱、热重等性质以及对Cu2+、Zn2+和Pb2+的吸附能力。结果表明,4种胺化硅胶对Pb2+的吸附量均大于Cu2+和Zn2+的吸附量,其中DETA修饰硅胶对Pb2+的吸附量较高。4种胺化硅胶对Pb2+的吸附过程较好地符合拟二级动力学模型以及Langmuir和Scatchart等温吸附热力学模型,其对Pb2+吸附的速率常数、饱和吸附量以及吸附位点数由大到小的顺序一致,均为SG-DETASG-TEPASG-EDASG-TETA。4种胺化硅胶对Pb2+的吸附速率和吸附量呈现"奇数胺"增强效应,亲和常数则依次减小。阐明了脂肪多胺修饰硅胶对Pb2+的吸附规律,并进一步讨论了Scatchart和Langmuir热力学模型的统一性。     

Preparation of lactic acid modified cellulose nanoparticles by microwave heating for preconcentration of copper from blood and food samples

In this study, nano-sized cellulose modified with lactic acid (MW-Ce-LA) was prepared with the assistant of microwave then used for the adsorption of Cu²⁺ from real samples. This modified cellulose was characterized by means of FTIR, TEM, XRD, and elemental analysis. ICP-OES was used for determination of Cu²⁺. The effect of pH, adsorption times, temperature, sorbent dose, and initial adsorbate concentration were studied to detect the ideal adsorption condition. Langmuir model proved to be the best to fit the adsorption isotherm experiments with maximum adsorption capacity of 90.3 mg g^?1 Cu²⁺. Calculated thermodynamic parameters (ΔG° and ΔH°) for adsorption of Cu²⁺ on MW-Ce-LA suggested exothermic and nonspontaneous character of the adsorption process. The reusability tests indicated regeneration of the prepared adsorbent simply using 1 mol L^?1 of HCl. The examined method was used effectively to preconcentrate Cu²⁺ from water, blood, and food samples.

     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源，CTAB和PEG-6000为模板剂，合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌，并且以该样品为吸附剂，对含Cu²⁺的溶液进行了静态吸附实验。结果表明，以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41，其比表面积为869.5 m²/g，孔容为0.97 cm³/g，平均孔径为3.3 nm；溶液pH为5~6时，MCM-41对Cu²⁺的去除效果最好；MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g；MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明，该过程符合准二级动力学模型。     

Multi-component adsorption of copper,nickel and zinc from aqueous solutions onto activated carbon prepared from date stones

The removal of Cu²⁺, Ni²⁺, and Zn²⁺ ions from their multi-component aqueous mixture by sorption on activated carbon prepared from date stones was investigated. In the batch tests, experimental parameters were studied, including solution pH, contact time, initial metal ions concentration, and temperature. Adsorption efficiency of the heavy metals was pH-dependent and the maximum adsorption was found to occur at around 5.5 for Cu, Zn, and Ni. The maximum sorption capacities calculated by applying the Langmuir isotherm were 18.68 mg/g for Cu, 16.12 mg/g for Ni, and 12.19 mg/g for Zn. The competitive adsorption studies showed that the adsorption affinity order of the three heavy metals was Cu²⁺?>?Ni²⁺?>?Zn²⁺. The test results using real wastewater indicated that the prepared activated carbon could be used as a cheap adsorbent for the removal of heavy metals in aqueous solutions.     

Kinetic studies of adsorption of lead(ll) from aqueous solution by wine-processing waste sludge.

A waste sludge produced from a wine-processing wastewater treatment process was used as an adsorbent to removal of heavy metal-lead(II) from aqueous solution. Results of kinetic experiments demonstrated that the adsorption was effective and rapid. Four different kinds of adsorption kinetic models (i.e., pseudo-first-order, pseudo-second-order, and two intra-particular mass diffusion models) were used to investigate the adsorption mechanisms. A normalized standard deviation was used to find the best adsorption kinetic model for the removal of lead(ll) by the sludge. The comparison shows that the kinetic adsorption data can be well-described by the pseudo-second-order adsorption model and that sorption might be a rate-limiting control. The adsorption-rate constant and adsorption capacity of pseudo-second-order adsorption equation were calculated. The parameters (initial lead(II) concentration, sludge-particle size, and sludge dosages), which affect the adsorption capacity of sludge, were discussed by using the pseudo-second-order adsorption equation.