Ru-TiO_2光电极对亚甲基蓝的光电催化降解

采用阳极氧化法制备Ru-TiO2光电极,以该电极为工作电极,石墨作对电极,饱和甘汞电极为参比电极,对亚甲基蓝溶液的光电催化降解进行了研究。结果表明:煅烧温度600℃,掺杂1%Ru的Ru-TiO2光电极催化活性最好;以紫外灯(125 W)为光源,当外加偏压0.2 V,pH为5时,Ru-TiO2光电催化亚甲基蓝120 min可使其完全脱色;亚甲基蓝的光电催化降解遵从Langmuir-Hinshelwood动力学模型,测得其反应速率常数k=0.781 mmol/(L.min),吸附常数K=0.225 L/mmol。     

基于过碳酸钠的类Fenton体系对亚甲基蓝的降解动力学

采用改良低温结晶法制备过碳酸钠(sodium percarbonate,SPC),对其进行XRD表征,并用以作为氧化剂构建类Fenton体系(SPC/Fe~(2+))降解亚甲基蓝(MB),对其降解的影响因素及反应动力学进行了研究。结果表明,在该体系中,当溶液初始pH分别为2~10时,亚甲基蓝的去除率在1 min时均可达到97%以上,说明该体系可高效去除水体中的亚甲基蓝,反应速率快,且过碳酸钠的使用可以拓宽Fenton反应的pH范围。该反应的最佳工艺条件为0.75 g·L~(-1)硫酸亚铁,300 mg·L~(-1)过碳酸钠,亚甲基蓝去除率在反应10 min后可达99.0%。亚甲基蓝在该体系中的降解遵循二级反应动力学方程,反应速率常数分别为64.50×10~(-3)L·(mol·s)~(-1),快于Fenton体系的17.83×10~(-3)L·(mol·s)~(-1)。该体系反应活化能为16.6 kJ·mol~(-1),远小于Fenton体系(46.234 kJ·mol~(-1)),说明以过碳酸钠为氧化剂更有利于非均相类Fenton反应的发生。     

Ru-TiO2光电极对亚甲基蓝的光电催化降解

采用阳极氧化法制备Ru—TiO2光电极，以该电极为工作电极，石墨作对电极，饱和甘汞电极为参比电极，对亚甲基蓝溶液的光电催化降解进行了研究。结果表明：煅烧温度600oC，掺杂1％Ru的Ru-TiO2光电极催化活性最好；以紫外灯（125W）为光源，当外加偏压0．2V，pH为5时，Ru-TiO2光电催化亚甲基蓝120min可使其完全脱色；亚甲基蓝的光电催化降解遵从Langmuir—Hinshelwood动力学模型，测得其反应速率常数k：0．781mmol／（L·min），吸附常数K=0．225L／mmol。     

铁碳微电解填料制备及其对亚甲基蓝的降解

针对传统铁碳微电解工艺中填料易板结的问题,在较低的烧结温度800℃条件下,将铁、活性炭、粘结剂和催化剂按一定配料比混合烧结4 h制备了一种铁碳微电解填料。将印染废水中的染料成分亚甲基蓝作为目标污染物,探究溶液pH、铁碳材料添加量和亚甲基蓝起始浓度等反应条件对亚甲基蓝降解效率的影响。在pH=3,铁碳投加量30 g·L~(-1),亚甲基蓝浓度10 mg·L~(-1)的条件下,亚甲基蓝的去除率达到55%左右;相同条件下对于微电解填料的循环使用实验中亚甲基蓝的去除率能维持在50%以上,证明了该微电解填料具有连续运行的能力。另外,通过微电解与芬顿反应联用的初步实验发现联用效果对于亚甲基蓝的降解率能大幅度提升至90%以上,证明微电解与芬顿反应联用具有较大的应用潜力。     

热氧化法制备Ti/RuO_2-TiO_2-IrO_2电极及处理亚甲基蓝废水

采用热氧化法制备Ti/RuO_2-TiO_2-IrO_2钛基氧化物材料,通过SEM、XRD、XRF等方法对制备物形貌和结构进行表征分析,用该涂层材料为阳极,不锈钢为阴极,活性炭颗粒为粒子电极构成电解系统处理亚甲基蓝模拟废水。结果表明,电解时间60 min时,该装置对亚甲基蓝脱色率达到87.83%,COD去除率达到74.45%,脱色率符合表观一级反应动力学规律。将Ti/RuO_2-TiO_2-IrO_2电极与其他常用电极对MB废水的降解效果进行比较分析,该电极对废水脱色率高于其他电极。     

亚甲基蓝表面修饰纳米TiO2降解造纸废水动力学

以亚甲基蓝(MB)作为表面修饰剂,采用简单的化学吸附法制备亚甲基蓝表面修饰的纳米TiO2光催化剂(TiO2-MB)。经表面修饰后,TiO2-MB光催化剂波长响应范围红移至可见光区575 nm处。探讨了光催化剂量、光照时间和溶液pH值对TiO2-MB光催化降解造纸废水的影响;研究了纳米TiO2-MB对造纸废水的暗吸附规律和光降解性能。结果表明:纳米TiO2-MB对造纸废水的吸附规律都较好地符合Langmuir和Freundlich吸附等温模型,属于吸热反应;光催化降解动力学符合Langmuir-Hinshelwood动力学模型。在160 W高压汞灯光照80 min,3.0 g/L纳米TiO2-MB光催化降解pH=2.0的造纸废水(COD:2 069.8 mg/L),COD去除率可达94.7%,处理效果远高于避光条件下。光催化剂经8次使用仍具有较高的催化活性。     

ZnO在光催化降解亚甲基蓝染料领域中应用研究

以Zn(CH3COO)2·2H2O为起始原料,采用非水解溶胶—凝胶法合成ZnO光催化剂,并对其进行了表征。以亚甲基蓝为光催化反应的模型化合物,考察了ZnO光催化剂的紫外光催化活性,探索了清除剂(异丙醇、草酸铵、对苯醌、H2O2酶)对ZnO紫外光催化活性的影响。结果表明,此方法制备的ZnO具有良好的光催化性能,光照1h,ZnO光催化降解亚甲基蓝的脱色率达到84.1%;而同样条件下,TiO2光催化降解亚甲基蓝的脱色率为73.8%。     

复合型生物炭对废水中亚甲基蓝的吸附作用

以木屑、二氧化硅为原料,采用慢速热解法制备了木屑生物炭(BC)和木屑-二氧化硅复合型生物炭(CBC),并对其物理化学性质进行表征,同时研究其吸附水中亚甲基蓝的吸附等温方程、动力学过程和影响因素。结果表明,和BC相比,CBC的比表面积、孔体积和平均孔径分别增加了2.85、7.00、1.21倍。CBC和BC对亚甲基蓝的吸附符合Langmuir吸附等温方程,其最大吸附量分别为26.60、5.37mg/g,CBC对亚甲基蓝的吸附能力更强。CBC和BC对亚甲基蓝的吸附动力学过程遵循准二级动力学方程。此外,和BC相比,CBC对亚甲基蓝的吸附效果受pH和离子强度影响较小。     

累托石/氧化亚铜纳米复合材料的制备及光催化性能研究

以累托石为载体,用液相合成法制备了累托石/纳米氧化亚铜复合材料,采用SEM、XRD对其进行了表征,并以吸附降解亚甲基蓝的效果探讨了复合材料的吸附及光催化性能.结果表明,在最佳条件为:溶液呈碱性,亚甲基蓝初始浓度90 mg/L,复合材料用量1.33 g/L,温度60℃,反应20 mim时复合材料对亚甲基蓝的降解率可达到9...     

酸改性泥炭对含亚甲基蓝废水的吸附净化作用

采用稀硝酸对泥炭进行改性处理获得酸改性泥炭,并将其用于处理亚甲基蓝废水。考察初始溶液pH、接触时间、酸改性泥炭投加量和亚甲基蓝溶液初始浓度等因素对酸改性泥炭吸附效果影响。结果表明,初始溶液pH、接触时间、酸改性泥炭投加量和亚甲基蓝溶液初始浓度对酸改性泥炭吸附性能都有一定的影响。在最佳的反应条件下(接触时间为60 min,反应温度为35℃,初始溶液pH为7.12,酸改性泥炭投加量为2 g),亚甲基蓝去除率可达90.88%,其吸附较好地符合Freundlich和Langmuir等温方程,拟合相关系数均大于0.9。通过热力学计算发现,ΔG<0、ΔS>0,表明该吸附反应是自发的、吸热反应。且该吸附过程符合准二级动力学方程(R2=0.98)。     

Treatment of dilute methylene blue-containing wastewater by coupling sawdust adsorption and electrochemical regeneration

In the present work, the coupling of adsorption and electrochemical oxidation on a boron-doped diamond (BDD) electrode to treat solutions containing dyes is studied. This coupling may be convenient for the treatment of diluted pollutant that is limited by the low rate of electrooxidation due to mass-transfer limitation. A pre-concentration step by adsorption could minimize the design of the electrochemical reactor. The adsorbent chosen was mixed with softwood sawdust, and methylene blue was chosen as the model dye molecule. Isotherms of adsorption and kinetics were investigated as well as the effects of current density and regeneration time. The BDD electrochemical oxidation of methylene blue adsorbed onto sawdust led simultaneously to its degradation and sawdust regeneration for the next adsorption. It was observed that multiple adsorption and electrochemical regeneration cycles led to an enhancement of adsorption capacity of the sawdust. This study demonstrated that adsorption–electrochemical degradation coupling offers a promising approach for the efficient elimination of organic dyes from wastewater.     

New catalyst comprising Silicotungstic acid and MCM-22 for degradation of some organic dyes

A heterogeneous catalyst comprising Keggin type polyoxometalate, silicotungstic acid (SiW₁₂), and MCM-22 was synthesized using wet impregnation method and characterized by acidity measurement, BET, FT-IR, XRD, and SEM. Their catalytic activity was evaluated for the degradation of cationic organic dyes like methylene blue (MB), crystal violet (CV), and an azo dye Chryosidine Y (CY) in an aqueous solution. The experimental parameters such as catalyst amount, initial dye concentration, and contact time were studied for the degradation of dyes, and it was found that the cationic dyes like methylene blue and crystal violet show better activity as compared to azo dye Chryosidine Y. This may be attributed to better electrostatic interaction of these cationic dyes with the residual negative surface charge of the catalyst, due to presence of SiW₁₂ ion as it is rich in surface oxygens and surface hydroxyl groups. The control experimental results showed that the presence of SiW₁₂ at the surface of MCM-22 promoted the degradation reactions, and presence of multiple W–O bonds in polyoxometalate also played a key role in this reaction. The catalyst exhibits recycling ability without any significant loss in activity up to four cycles.

     

污泥活性炭对次甲基蓝废水的吸附

立足于污泥的资源化,利用化学活化法制得的污泥基活性炭,处理次甲基蓝染料废水.考察了污泥活性炭的粒径以及染料废水的pH值对染料脱色效果以及活性炭的吸附量的影响,并对吸附过程进行等温吸附线和吸附动力学分析.结果表明,在本研究的范围内,污泥活性炭的粒径越小、染料废水的pH值越高,则污泥活性炭对染料废水的吸附效果越好.当粒径在200目以上时,去除率及吸附量分别为88.2％和136.7 mg/g;当pH值为11时,去除率和吸附量分别为90.4％和91.9 mg/g.污泥活性炭对次甲基蓝染料的吸附脱除符合Langmuir吸附等温线和Lagergren准二级动力学方程.     

新型二氧化铅电极处理有机染料废水的研究

研究了高压塑片法制备新型二氧化铅电极的工艺,通过循环伏安、X衍射和扫描电镜等手段对电极性能的考察表明,该电极不仅具有高电催化活性,还有很好的抗腐蚀性能.通过与普通石墨电极的对比实验,进一步探讨了该电极降解中性枣红染料的机制和工艺条件.结果表明,该电极在脱色和COD降解方面都有明显的优越性.在含磷酸盐和氯离子的体系中,降解效率尤为突出.     

新型二氧化铅电极处理有机染料废水的研究

研究了高压塑片法制备新型二氧化铅电极的工艺,通过循环伏安、X衍射和扫描电镜等手段对电极性能的考察表明,该电极不仅具有高电催化活性,还有很好的抗腐蚀性能.通过与普通石墨电极的对比实验,进一步探讨了该电极降解中性枣红染料的机制和工艺条件.结果表明,该电极在脱色和COD降解方面都有明显的优越性.在含磷酸盐和氯离子的体系中,降解效率尤为突出.     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.     

Electrochemical degradation of Acid Blue and Basic Brown dyes on Pb/PbO2 electrode in the presence of different conductive electrolyte and effect of various operating factors

Electrocatalytic degradation of Acid Blue and Basic Brown dyes from simulated wastewater on lead dioxide anode was investigated in different conductive electrolytes. It was shown that complete degradation of these dyes is dependent primarily on type and concentration of the conductive electrolyte. The highest electrocatalytic activity was achieved in the presence of NaCl (2g/l) and could be attributed to indirect oxidation of the investigated dyes by the electrogenerated hypochlorite ions formed from the chloride oxidation. In addition, contribution from direct oxidation could also be possible via reaction of these organic compounds with the electrogenerated hydroxyl radicals adsorbed on the lead dioxide surface. In the presence of NaOH, the electrocatalytic activity of the employed anode was not comparable to that in NaCl due primarily to the absence of chloride. This indicates that dyes degradation in NaOH occurs exclusively via direct electrochemical process. However, in H2SO4, the electrode performance was poor due partially to the absence of chloride from the conductive solution. The possibility of electrode poisoning as a result of growth of adherent film on the anode surface or production of stable intermediates not easily further oxidized by direct electrolysis in H2SO4 might also be accountable for the poor performance observed in this conductive electrolyte. Optimizing the conditions that ensure effective electrochemical degradation of Acid Blue and Basic Brown dyes on lead dioxide electrode necessitates the control of all the operating factors.     

Degradation of carbofuran in water by solar photocatalysis in presence of photosensitizers

The effect of the presence of photosensitizers, methylene blue (MB) and rose Bengal (RB), on the degradation of carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate) in water in a solar photocatalytic system was investigated. It was found that as compared to MB, RB generally showed a stronger effect on the decomposition of carbofuran under comparable conditions. Among the conditions studied, adding 2 x 10(-6) M of RB, that corresponding to 2% of the initial concentration of carbofuran solution in the system, rendered the most effective degradation of carbofuran. As a result, a carbofuran removal percentage of 69.9%, a mineralization efficiency of 28.0%, and a microtoxicity reduction of 65.0% could be achieved. The degradation and mineralization of carbofuran was found to follow the pseudo-first order reaction kinetics. The decomposition mechanism of carbofuran was further investigated through identification of the intermediates to elaborate the influence of dye photosensitizer on the solar photocatalysis of carbofuran in water. On the basis of the intermediates identified, including carbofuran phenol, 3-hydroxy carbofuran phenol, and substituted alcohols (3-phenoxy 1-propanol, 2-ethyl 1-hexanol, 2-butoxyl ethanol), it appears that hydrolysis and hydroxylation were the two key mechanisms for decomposing carbofuran during the process of solar photocatalysis with the aid of dye photosensitizer.